CERAMICS INTERNATIONAL
·
2023
·Vol. 50
·期 6
·9753-9761
·
IF 5.2
Li Li,Haoliang Yang,Yongjie Wang,Faling Ling,Xianju Zhou,Guotao Xiang,Zhongmin Cao,Sha Jiang,Zhiyu Yang,Yongbin Hua
Novel Ca 2 ScNbO 6 (CSNO): Cr 3+ phosphors were synthesized through a solid-phase method. The crystal structures, luminescence performances, and applications were introduced in this work. The optimized doping concentration was found with a Cr 3+ concentration of 0.01 mol. Under the 336 nm excitation, the recorded photoluminescence spectrum in the range of 650–1300 nm indicated that the obtained sample can emit a broad near-infrared emission with a dominant peak of 858 nm while the full width at half maximum (FWHM) was determined to be 191 nm. To gain a deeper comprehension of the luminescent properties, the crystal field strength was investigated as Dq/B = 2.03, and the electron-phonon coupling for parameter S was calculated to be about 2.01. As for the potential application, utilizing the variable temperature decay lifetime technique, the relative sensitivity (S R ) was approximately 1.16% K −1 at 387 K, which can be promised for utilization in optical temperature measurement. On the other hand, a near-infrared phosphor-converted lighting-emitting diode ( Pc -LED) was fabricated for night vision. Eventually, the security ink based on the obtained sample was made for use in the anti-counterfeiting field.
研究领域:
材料科学
·
光学工程
·
无机化学
·
功能材料
·
生物医学工程
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Decai Huang,Sisi Liang,Dejian Chen,Jie Hu,Kunyuan Xu,Haomiao Zhu
The emerging applications of near-infrared (NIR) spectroscopy technology in medicine and food security call for compact and efficient NIR light source such as NIR phosphor converted LEDs (pc-LED). Currently, most of the NIR phosphors suffer from low photoluminescence (PL) quantum yield and poor thermal or chemical stability. Herein, a fluoride garnet NIR Na 3 Al 2 Li 3 F 12 :Cr 3+ phosphor was successfully synthesized via coprecipitation method. It can be excited efficiently by blue or red light and shows a broad emission band covering 650–1000 nm (bandwidth of ~110 nm) with a PL quantum yield of 78%. The fine electronic structure of Cr 3+ ions in the host was revealed by the measurement of temperature-dependent (8–300 K) excitation and emission spectra analysis. Particularly, at 423 K, the Na 3 Al 2 Li 3 F 12 :5%Cr 3+ sample retained ~99% of the PL intensity at room temperature, exhibiting excellent PL thermal stability. A NIR pc-LED was fabricated by combining the Na 3 Al 2 Li 3 F 12 :5%Cr 3+ phosphor with a commercial blue LED chip, and radiant flux of 14.3 mW in NIR region was obtained at 60 mA drive current. Furthermore, the penetration of NIR light generated by this pc-LED in chicken breast was reached. The results suggested that Na 3 Al 2 Li 3 F 12 :Cr 3+ is a promising candidate for broadband pc-LED in NIR spectroscopy applications.
研究领域:
材料科学
·
光学工程
·
生物医学光子学
·
半导体器件
·
分析化学
✓ 已验证
DOI
高影响因子
OPTICS AND LASER TECHNOLOGY
·
2024
·
IF 4.6
Shulei Li,Zhenxu Lin,Quantong Deng,Fu Deng,Mingcheng Panmai,Junying Chen,Yuheng Mao,Shimei Liu,Jun Dai,Yunbao Zheng,Rui Huang,Sheng Lan
Realization of long-term stable lasing from all-inorganic perovskite supercrystals is highly desirable for practical applications in optoelectronic devices. However, lasing from perovskite supercrystals excited by continuous wave laser light remains a challenge due to the photoluminescence degradation induced by thermal accumulation. Here, we report highly stable lasing with low threshold fom a CsPbClBr 2 supercrystal placed on a thin Ag film, which form a CsPbClBr 2 /Ag microcavity, by managing the thermal distribution inside the CsPbClBr 2 supercrystal. Combined numerical simulations and lifetime measurements, the localized electric field in such a hybrid microcavity leads to a spatially localized temperature distribution, which plays a crucial role in suppressing the thermal accumulation on the surface and in eliminating non-radiative recombination defects. The effective thermal management in the hybrid microcavity renders highly stable lasing with low threshold under the irradiation of continuouw wave laser light. Our findings provide a feasible and universal approach to the development of long-term stable perovskite laser.
研究领域:
光学工程
·
凝聚态物理
·
材料科学
·
纳米光子学
·
激光技术
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2021
·
IF 3.599
Yanting Zhu,Chenxia Li,Degang Deng,Hua Yu,Hao Li,Le Wang,Changyu Shen,Xufeng Jing,Shiqing Xu
A series of Eu 2+ /Cr 3+ co-doped BaAl 12 O 19 phosphor was synthesized by traditional high temperature solid stated method, and the temperature-sensitive characteristic of the phosphor was researched. Due to the temperature sensitivity of the fluorescence lifetime of Cr 3+ , the thermometry based on fluorescence lifetime can be realized. Furthermore, the emissions of Eu 2+ ion and Cr 3+ ion can be well separated, which shows the excellent signal recognition ability of this phosphor. The Eu 2+ /Cr 3+ co-doped BaAl 12 O 19 phosphor can be used for the thermometry based on fluorescence intensity ratio. A dual-mode optical thermometry is proposed and researched in the temperature range of 293–563 K by using the decay lifetime of Cr 3+ emission and in the temperature range of 295–476 K by using the fluorescence intensity ratio of Eu 2+ to Cr 3+ as temperature readout. The maximum values of relative sensitivity are 0.466% K −1 at 363 K and 0.259% K −1 at 476 K. The Eu 2+ /Cr 3+ co-doped BaAl 12 O 19 phosphor has excellent optical temperature characteristic , and its dual-mode thermometry characteristics provide convenience for the application of this material. This phosphor has potential application prospects in the field of optical thermometry.
研究领域:
材料科学
·
光学工程
·
无机化学
·
传感器技术
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2022
·
IF 6.371
Yonghui Xu,Liang Zhang,Shuwen Yin,Xiudi Wu,Hongpeng You
Despite significant progress has been made in the luminescent materials for white light emitting diodes (WLEDs), it is still desirable to develop novel highly efficient phosphors with appropriate excitation and high visible emission for high color rendering WLEDs. In this study, we report a novel phosphor BaGa 2 Si 2 O 7 :Ce 3+ ,Tb 3+ (BGSO:Ce 3+ ,Tb 3+ ) with highly effective green luminescence. BGSO:Ce 3+ ,Tb 3+ phosphor represents a broad excitation band in the range of 300–400 nm and intense emission at approximately 542 nm with a high photoluminescence quantum efficiency of 76.4%. The structure, luminescence, and energy transfer from the Ce 3+ and Tb 3+ ions were investigated in detail. Moreover, the incorporation of Na + or K + ions into BGSO:Ce 3+ ,Tb 3+ for charge compensation can improve the emission intensity and thermal stability. Moreover, a near ultraviolet (n-UV) pumped prototype WLED device was fabricated and it exhibited bright warm-white light with CIE chromaticity coordinates of (0.3561, 0.3344), high color-rendering index (Ra=90.4), and low CCT (3330 K) upon 20 mA driving current. This work provides a new strategy to develop high-quality solid-state LED phosphors.
研究领域:
材料科学
·
光学工程
·
固体物理
·
发光材料
·
半导体器件
✓ 已验证
DOI
高影响因子
MATERIALS RESEARCH BULLETIN
·
2023
·
IF 5.4
Huimin Li,Shan Wang,Ran Pang,Lihong Jiang,Da Li,Su Zhang,Chengyu Li,Hongjie Zhang
Contactless thermometer based on fluorescence intensity ratio shows unparalleled characteristics compared with traditional contact thermometers. However, few materials are suitable for high temperature (above 573 K) measurement. In this work, Pr 3+ was selected as the emitter and Y 3 GaO 6 :xPr 3+ luminescent thermometers were designed. The phase, crystal structure and morphology were identified using X-ray diffraction, Rietveld refinement and scanning electron microscope. The spectra with multiple ranges were temperature sensitive due to the cross-relaxion mechanism that occurs in the luminescence process. The parameters for temperature measurement were determined based on the peak intensity ratio of 506 and 610 nm at different temperatures (from 293 to 823 K). Y 3 GaO 6 :0.01Pr 3+ displays excellent temperature sensitive performance, in which the relative sensitivity values increase along with the temperature in a wide temperature range and reach 4.09 % K −1 . The thermometric visualization in Y 3 GaO 6 :xPr 3+ can be achieved due to the widely varying luminescence colors at different temperatures.
研究领域:
材料科学
·
光学工程
·
无机化学
·
传感器技术
·
功能材料
✓ 已验证
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2016
·Vol. 18
·期 10
·7341-7348
·
IF 4.449
Xiong Liu,Dong Wang,Hong Gao,Zhou Yang,Yan Xing,Hui Cao,Wanli He,Huihui Wang,Jianming Gu,Huiying Hu
A novel kind of monodonor–bisacceptor (D–A–A) C60 charge-transfer complex was synthesized by the high-yielding [2+2] click chemistry reaction and the Prato reaction. Both electrochemical and UV-vis spectra studies were carried out and they proved that the side groups of the fullerene derivatives played an important role in the energy gaps, and also affected the third-order non-linear optical response. The experimental investigation on the third-order non-linear optical phenomena of the fullerene derivatives was measured using the Z-scan technique at different wavelengths (532 nm and 1064 nm). All the compounds exhibited very special non-linear optical properties when pumped by 21 ps pulses at 532 nm which suggested that there were two different types of reversible photo-isomerization. The optical-limiting performance has also been studied which proved indirectly the mechanism models of the reversible photo-isomerization.
研究领域:
材料科学
·
光学工程
·
纳米化学
·
非线性光学
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2014
·Vol. 26
·期 2
·884-890
·
IF 1.966
Li Rui,Wang Yan-ze,Mao Zhi-yong,Wang Da-Jian
A remote phosphor coating by using Sr 3 (Al,Si)(O, F) 5 :Ce 3+ (SASF:Ce 3+ ) on glass substrate was prepared by a simple and convenient screen printing method. The crystalline phase and the distribution of SASF:Ce 3+ crystals in coating were investigated by XRD and SEM, respectively. The scattering light and absorption light properties of remote phosphor coating with different thicknesses were discussed through Lambert–Beer’s law. The relationship between luminous efficiency and absorption coefficient was demonstrated. White light emitting diode prototype fabricated with blue chip and the prepared patterned SASF:Ce 3+ remote phosphor in this work showed excellent performances, opening a cost-effective process to generate planar white light.
研究领域:
材料科学
·
光学工程
·
发光材料
·
固态照明
·
功能涂层
✓ 已验证
DOI
高影响因子
Materials Today Chemistry
·
2022
·
IF 7.613
S. Wu,Y. Fu,Q. Liu,P. Xiong,D. Wang,G. Zhang,S. Yuan,Y. Chen
Developing highly efficient cyan-emitting fluorescent materials is essential to bridge the cyan gap in phosphor-converted white light-emitting diodes for full-spectrum white illumination. Here, a Bi-doped cyan phosphor has been reported to solve this gap. The phase purity, photoluminescence emission/excitation spectra, concentration quenching, lifetime decay curves, and temperature-dependent photoluminescence emission spectra were systematically investigated. SrLaGaO 4 :Bi 3+ exhibits a broad excitation band (250–400 nm), which matches with the emission of a commercial near-ultraviolet light-emitting diode chip. The cyan light peaked at 475 nm is observed, which is attributed to the 3 P 1 → 1 S 0 transition of Bi 3+ . The thermal quenching experiment was performed, and the activation energy was calculated as 0.36 eV. Finally, full-spectrum white light-emitting diode devices were fabricated using SrLaGaO 4 :Bi 3+ phosphors, commercial blue BaMgAl 10 O 17 :Eu 2+ phosphor, green (Ba, Sr) 2 SiO 4 :Eu 2+ phosphor, and red CaAlSiN 3 :Eu 2+ phosphor, which displayed an International Commission on an illumination coordinate of (0.3732, 0.3850), a correlated color temperature of 4290 K, and a color rendering index of 93.2 at a drive current of 20 mA. This result indicates that SrLaGaO 4 :Bi 3+ plays an essential role in bridging the cyan gap, providing new inspiration for applying cyan-emitting phosphors in full-spectrum white lighting.
研究领域:
材料科学
·
光学工程
·
固态照明
·
发光材料
·
无机化学
✓ 已验证
DOI
高影响因子
Solar RRL
·
2017
·Vol. 1
·期 10
·1700084
·
IF 0
Yuehui Lu,Zhicheng Chen,Ling Ai,Xianpeng Zhang,Jing Zhang,Jia Li,Weiyan Wang,Ruiqin Tan,Ning Dai,Weijie Song
Photovoltaic (PV) modules are not only an opto-electrical system, but also opto-thermal one, where the optical, electrical, and thermodynamic domains are strongly coupled. The means to suppress both light and heat losses in PV modules remains undeveloped. Herein, a universal route to realize both radiative cooling and light management via the ultra-broadband versatile textures is proposed, originating from the interaction with the visible, near-infrared, and mid-infrared electromagnetic waves (EMWs) via geometric, diffractive, and subwavelength optical effects. The sol–gel imprinted ultra-broadband textures exhibited a near-unity infrared emissivity over 0.96 at the atmospheric window between 8 to 13 μm for radiative cooling, and a solar transmittance and haze above 0.94 and 0.95 at the wavelengths from 350 to 750 nm, respectively, for light management. Applying the ultra-broadband textures imprinted glass to silicon PV modules as an encapsulant cover, the short-circuit current and conversion efficiency were increased by 5.12 and 3.13% in relative terms, respectively. The fabrication of such ultra-broadband versatile textures was photolithography-free, scalable, and PV industry compatible, which provided a cost-effective, long-term durable, and energy-efficient means to both light and thermal management through ultra-broadband matter-EMW interaction not only in PV modules, but also various opto-electro-thermal devices.
研究领域:
光学工程
·
材料科学
·
能源科学
·
光伏技术
·
热力学
·
纳米制造
·
电磁波与物质相互作用
✓ 已验证
DOI
Science China-Materials
·
2021
·Vol. 64
·期 8
·2008-2016
·
IF 8.273
Wen Xin,Lin Chensheng,Luo Min,Fan Huixin,Chen Kaichuang,Ye Ning
[PO 4 ] 3− possesses small microscopic second-order susceptibility and polarizability anisotropy, which inherently result in weak second-harmonic generation (SHG) and small birefringence. Herein, a new noncentrosymmetric phosphate, [C(NH 2 ) 3 ] 3 PO 4 ·2H 2 O, was successfully designed and synthesized by a solution evaporation method. [C(NH 2 ) 3 ] 3 PO 4 ·2H 2 O without metal ions is composed of planar conjugated guanidine cations and PO 4 tetrahedrons, which are connected by hydrogen bonds, forming a three-dimensional network. Physical property measurements indicate that the title compound displays an SHG response of 1.5 × KH 2 PO 4 (KDP) and a larger birefringence (0.055@546.1 nm) compared with most reported ultraviolet nonlinear optical phosphates. Furthermore, first-principles calculations reveal that the π-conjugated planar [C(NH 2 ) 3 ] + cations and [PO 4 ] 3− groups are responsible for its excellent linear and NLO properties.
研究领域:
材料科学
·
光学工程
·
无机化学
·
晶体工程
·
非线性光学
✓ 已验证
DOI
高影响因子
OPTICAL MATERIALS
·
2021
·
IF 3.08
Xiang Meng,Jiajun Ma,Kang Xie,Liang Hong,Junxi Zhang,Zhijia Hu
We have demonstrated a low threshold and tunable flexible random laser (RL) in dye-doped poly ethylene glycol diacrylate (PEG-DA) hydrogel, which was prepared by crosslinking polymerization using PEG-DA monomer and photoinitiator. The random lasering is attributed to the light scattering from the porous structure of hydrogels, and the wavelength of random lasing can be tuned by ~3.2 nm in the temperature range from 30 °C to 70 °C. Under the continuous increasing and decreasing temperature cycle, the random lasing tunable phenomenon can still be observed, which proves that this flexible material can be used as a new temperature sensor . In addition, we also explored the application of flexible laser in phototherapy. Considering the good elasticity and transparency of hydrogels, this thermo-responsive property will be of great significance to the biomedical applications of flexible material.
研究领域:
生物医学工程
·
光学工程
·
高分子材料科学
·
光子学
·
生物传感器
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）