JOURNAL OF MEMBRANE SCIENCE
·
2020
·
IF 7.183
Yanwei Sun,Chunshan Song,Xinwen Guo,Sungwon Hong,Jungkyu Choi,Yi Liu
Metal-organic framework (MOF) membranes have received increasing attention due to their unprecedented potential for energy-efficient gas separation. Compared with other MOF materials (like ZIF), fabrication and microstructural manipulation of high-performance Ti-MOF-based membranes, although being very attractive due to their excellent chemical and thermal stability, remained relatively less investigated due to the limitations of available titanium sources and heating modes. In this study, different Ti sources (TPOT, TiS 2 , and MXene) and heating modes (conventional heating, multi-mode microwave heating, and single-mode microwave heating) were examined for the preparation of NH 2 -MIL-125 membranes showing diverse microstructures and gas separation performances. The present work revealed that for the first time, MXene , the new two-dimensional Ti carbide , could be used as Ti source for synthesizing MOF membranes. The best performing NH 2 -MIL-125 membranes, which were obtained with TiS 2 as the metal source under single-mode microwave heating, exhibited the highest H 2 /CO 2 selectivity (ca. 17.2) as well as considerable H 2 permeance (1.7 × 10 −7 mol m −2 s −1 Pa −1 ), owing to an enhanced non-thermal effect of single-mode microwave heating and balanced dissolution rate of TiS 2 .
研究领域:
材料科学
·
膜分离技术
·
化学工程
·
纳米材料
·
气体分离
·
可持续能源
✓ 已验证
DOI
高影响因子
RSC Advances
·
2015
·Vol. 5
·期 118
·97256-97263
·
IF 3.84
Qianqian Huang,Weiqiang Yu,Rui Lu,Fang Lu,Jin Gao,Hong Miao,Jie Xu
Catalytic conversion and application of bio-based platform chemicals is of great significance. Itaconic acid, one of the abundant and renewable bio-based platform chemicals, could be hydrogenated to produce methylsuccinic acid, which has important applications in pharmaceutical synthesis. Traditional catalysts can be corroded, leached and deactivated in an acid reaction environment, and the stability of the catalysts is a great challenge. Carbothermal reduction was employed to prepare stable ruthenium-based catalysts, and the results confirmed that CO generated in situ functioned as an efficient reducing species in the carbothermal reduction process. The catalysts were applied for the hydrogenation of itaconic acid, and showed good stability and resistance to acid with no obvious loss of activity and less leaching in recycling tests compared to hydrogen reduced samples which exhibited an apparent decrease of 22% for the conversion of itaconic acid. The carbothermal reduced catalysts could maintain 99% conversion and 99% selectivity for methylsuccinic acid, and maintained good stability and acid-resistance under a higher temperature and longer reaction time.
研究领域:
催化化学
·
绿色化学
·
生物质转化
·
有机合成
·
材料化学
·
工业催化
·
可持续能源
✓ 已验证
DOI
高影响因子
Journal of Energy Chemistry
·
2021
·
IF 9.676
Yu Kang,Yujia Han,Cong Wei,Kuo Liu,Ming Tian,Chuande Huang,Chaojie Wang,Jian Lin,Baolin Hou,Xiaoli Pan,Yang Su,Lin Li,Riguang Zhang,Yong Hao,Xiaodong Wang
Thermochemical two-step CO 2 splitting is a potential approach that fixes the sustainable resource into transportable liquid fuels. However, the harsh CO 2 splitting conditions, the limited oxygen release kinetics and capacity of metal oxides block further promoted the CO yield and solar-to-fuel energy efficiency. Here, we propose a different carbon cycle assisted by Ni/La 2 O 3 via coupling methane decomposition with thermochemical CO 2 splitting, replacing conventional metal oxides cycle. Superior performance was demonstrated with methane conversion reached around 94% with almost pure H 2 generation. Encouragingly, CO 2 conversion of 98% and CO yield of 6.9 mmol g −1 derived from CO 2 were achieved, with peak CO evolution rate (402 mL min −1 g −1 ) of orders of magnitude higher than that in metal oxide process and outstanding thermodynamic solar-to-fuel energy efficiency (55.5% vs. 18.5%). This was relevant to the synergistic activation of La 2 O 3 and Ni for CO 2 in carbon cycle, thus improving CO 2 splitting reaction with carbon species.
研究领域:
能源化学
·
催化化学
·
可持续能源
·
热化学转化
·
二氧化碳利用
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2011
·Vol. 36
·期 13
·7374-7380
·
IF 4.057
Wei Wang,Qiang Zhao,Jinxiang Dong,Jinping Li
A novel silver oxides oxygen evolving catalyst (Ag-OEC) for hydrogen production by water splitting was formed in situ on an indium tin oxide anode, in a near-neutral potassium tetraborate (K 2 B 4 O 7 ) electrolyte. The catalyst exhibited high activity and low overpotential for O 2 evolution under mild conditions. The main functional composition of the catalyst was a redox couple of Ag 2 O/AgO. Catalytic activity during oxygen evolution was evaluated by cyclic voltammetry and Tafel plot. The effects of the concentration, temperature, and pH of K 2 B 4 O 7 solution on the catalyst, and the Faradaic efficiency of the oxygen evolving reaction were examined. The results show that the Ag-OEC exhibits excellent oxygen evolution properties, with an oxygen evolving overpotential of 318 mV at a current density of 1 mA/cm 2 .
研究领域:
电催化
·
能源化学
·
材料科学
·
物理化学
·
可持续能源
✓ 已验证
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2024
·Vol. 12
·期 5
·114091
·
IF 7.4
Xiaolong Dai,Tiangui Qi,Xiaobin Li,Zhihong Peng,Guihua Liu,Qiusheng Zhou,Yilin Wang,Leiting Shen
In recent years, lithium iron phosphate (LFP) batteries have been widely used in the electric vehicle industry. The recycling of spent LFP will be propitious to conserving resources and alleviating the environmental risks it poses. In this study, a selective extraction method for lithium from spent LFP was proposed using nitric acid . Lithium leached into the liquid phase, while P and Fe remained in the leaching residue. Under the conditions of 120°C, HNO 3 /Li molar ratio of 2, and time of 2 h, the leaching efficiency of lithium reached 99.5 %, with a selectivity reaching 82.1 %. Initially, LFP was decomposed to liberate Li, Fe, and P in the liquid phase. Subsequently, ferrous ions were oxidized to trivalent, high-valent iron ions re-precipitated as FePO 4 ·2 H 2 O. Thermodynamic calculations indicate that the temperature and pH value of the extraction system have significant influence on both the oxidation and reprecipitation steps. An imbalance of Fe/P ratio (<1) in the raw material hinders the selectivity of lithium extraction , and supplementing this portion of Fe can enhance the selectivity to over 90 %. Additionally, LiCO 3 and anhydrous FePO 4 were effectively regenerated from the leachate and residue. This study provides a novel approach for the recycling of spent LFP and probably contributes to the sustainability of the lithium ion battery industry.
研究领域:
环境科学
·
冶金工程
·
材料回收
·
可持续能源
·
化学工程
✓ 已验证
DOI
高影响因子
APPLIED ENERGY
·
2024
·
IF 10.1
Yaning Kong,Honglin Yu,Mengqi Liu,Guodong Zhang,Fei Wang
Hydrate was considered to be the next generation hydrogen storage material , and hydrate-based hydrogen storage (HBHS) would play an important role in future hydrogen economy, but sluggish hydrate formation kinetics presents huge technological challenge for its application. Herein, a nano promoter of -SO 3 − @PSNS was prepared by soap-free emulsion polymerization , and a dual kinetic promoter system (L-methionine/-SO 3 − @PSNS) was applied to enhance the formation kinetics of mixed H 2 /DIOX hydrate. At a moderate condition (12 MPa and 274.15 K), hydration efficiency under a driving force of 2.1 MPa is significantly enhanced by the synergy of the dual kinetic promoters, hydrate induction time reduces from 443.2 ± 209.73 min to 24.7 ± 17.16 min, while hydrate growth rate increases by 43.75%, and hydrogen storage capacity is up to 0.473 ± 0.041 wt% that increases by 62.8%. At a more moderate condition (10 MPa and 274.15 K) with an extremely low driving force of 0.1 MPa, enhanced hydrate formation was obtained in a composite promotion system of the dual kinetic promoters and dual thermodynamic promoters (THF/DIOX), which also performs exceptionally in term of recycling. The presence of a small amount (0.35 mol%) of THF reduces the induction time by 93.5%, and hydrate growth rate increases by 130.18%, while satisfactory hydrogen storage capacity (0.346 ± 0.017 g/g) is still remained in mixed H 2 /DIOX/THF hydrate, the structure of which was confirmed by Raman spectrum . This work presents an effect approach on enhancing the formation kinetics of H 2 -contained hydrate under low driving force, and this finding provides important insight for HBHS.
研究领域:
物理化学
·
能源材料
·
气体储存
·
化学工程
·
纳米材料科学
·
分子模拟
·
可持续能源
✓ 已验证
DOI
高影响因子
Energy Technology
·
2018
·Vol. 7
·期 5
·1800927
·
IF 3.175
Jiacong Wu,Chunmei Li,Wenli Zhang,Juan Han,Lei Wang,Shuhao Wang,Yun Wang
It is a huge challenge for exploiting new photocatalysts with low-cost cocatalysts in place of precious metals to realize high-efficiency H 2 production from water. Herein, a new photocatalyst with a high H 2 production activity is prepared via modification of bimetallic manganese cobalt phosphide (Mn 0.67 Co 1.33 P) nanodots on graphitic carbon nitride (g-C 3 N 4 ). Moreover, the largest H 2 production rate of 113.1 μmol h −1 is obtained over the Mn 0.67 Co 1.33 P/g-C 3 N 4 -5 sample, which is about 2.75 times than that of Pt/g-C 3 N 4 -5 (41.2 μmol h −1 ). The high-performance H 2 production suggests page a page down that the modification effect of Mn 0.67 Co 1.33 P nanodots improves the visible harvest ability and separation efficiency of charge carriers. A typical example to improve the photocatalytic H 2 production performance by fabricating heterostructures using bimetallic phosphide to modify graphitic carbon nitride is provided.
研究领域:
材料科学
·
光催化
·
能源化学
·
纳米材料
·
可持续能源
✓ 已验证
DOI
高影响因子
JOURNAL OF ELECTROANALYTICAL CHEMISTRY
·
2019
·
IF 3.218
Xiaoxia Ren,Shou-Dong Xu,Shibin Liu,Liang Chen,Ding Zhang,Li Qiu
Biomass wastes or biomass derived hard carbon materials with the advantages of green, as well as economic and high reversible capacity have became the promising anode materials for sodium ion batteries (SIBs). Despite this, the poor rate capability hinders their further development. Here, we synthesized lath-shaped hard carbon materials derived from peanut shells by a two-step approach, namely a hydrothermal pretreatment for different treatment time first, and then a carbonized process at 800 °C. Morphology and structural characterizations (SEM, XRD and Raman) prove the hydrothermal pretreatment has a great influence on morphology transformation, the layer spacing, as well as the defect concentration which can enhance the adsorption sites of Na + and shorten the transport route of sodium ions . The PSDHCs-4 (hydrothermal treatment for 4 h) electrode can deliver the highest reversible capacity of 256 ± 5 mAh g −1 , and show the best capacity retention of 97 ± 2% at the current rate of 0.1 C after 100 cycles. More importantly, PSDHCs-4 electrode shows the excellent rate performances with a reversible capacity of 261, 244, 206, 163, 125, and 100 mAh g −1 at the current rates of 0.1, 0.2, 0.5, 1.0, 2.0 and 5.0 C, respectively. These remarkable electrochemical properties indicate that PSDHCs-4 material should be a promising anode material for SIBs.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米材料
·
可持续能源
·
碳材料
✓ 已验证
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2021
·
IF 10.588
Xuefeng Liu,Shijie You,Nanqi Ren,Hao Zhou,Jinna Zhang
This study reports the development of complete solar-driven dual-photoelectrode fuel cell (PFC) based on WO 3 photoanode and Cu 2 O photocathode with peroxymonosulfate (PMS) serving as cathodic electron acceptor . As indicated by photoelectrochemical measurements, the PMS was able to improve thermodynamic properties of photocathode, achieving an increased open circuit potential from 0.42 V to 0.65 V vs standard hydrogen electrode (SHE). Under simulated sunlight irradiation (~100 mW cm −2 ), the maximum power density of 0.12 mW cm −2 could be obtained at current density of 0.34 mA cm −2 , which was 8.57 times of that produced by PFC without PMS (0.014 mW cm −2 ). Correspondingly, adding PMS (1.0 mM) increased overall removal efficiency of 4-chlorophenol (4-CP) from 39.8% to 96.8%, accounting for the first-order kinetic constant ( k =0.056 min −1 ) being 6.67 times of that in the absence of PMS ( k =0.0084 min −1 ). Radical quenching and electron spin-resonance (ESR) results suggested the contribution of free radicals (•OH and SO 4 •- ) and non-radical pathway associated with direct activation of PMS by Cu 2 O photocathode. Fourier transformed infrared (FTIR) analysis confirmed the strong non-radical interaction between Cu 2 O photocathode and PMS, resulting in 4-CP removal via activation of PMS by surface complex on Cu 2 O. The proof-in-concept complete solar-driven dual-photoelectrode fuel cell may offer an effective manner to realize water purification and power generation, making wastewater treatment more economical and more sustainable.
研究领域:
环境科学
·
光催化
·
能源材料
·
电化学
·
水处理技术
·
可持续能源
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2018
·Vol. 7
·期 11
·5991-6000
·
IF 9.931
Weiguang Wang,Hua Tian,Gequn Shu,Dongxing Huo,Fang Zhang,Xiuping Zhu
A bimetallic thermally regenerative ammonia-based battery (B-TRAB) using inexpensive materials efficiently converts low-grade thermal energy into electricity with high power density. Through thermal regeneration of the anolyte, the B-TRAB system realized high-voltage discharge (1.38 V) with redox couples [Cu(II)/Cu and Zn(NH3)42+/Zn] and low-voltage charge (0.72 V) with Zn(II)/Zn and Cu(NH3)42+/Cu. Adding 2 M NH3 to the anolyte of a Cu/Zn-TRAB produced a peak discharge power density of 525 W m−2-electrode (120 W m−2-membrane), and the voltage (or current) and peak power could be doubled by connecting two cells in series (or parallel). In successive regeneration cycles, a maximum power density of 115 W m−2-electrode (26 W m−2-membrane) and a net energy density of 714 W h m−3 were produced at a constant current density of 100 A m−2. The power density was enhanced to 515 W m−2-electrode (118 W m−2-membrane) and maintained in successive cycles by adding acid to the regenerated catholytes, with a net energy density of 299 W h m−3 (discharged at a constant load of 12 Ω and charged at a constant current density of 100 A m−2). A thermal-electricity conversion efficiency of 0.95% (10.7% relative to the Carnot efficiency) was achieved.
研究领域:
能源材料
·
电化学工程
·
热电转换技术
·
可持续能源
·
功能材料
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2022
·Vol. 47
·期 33
·14916-14929
·
IF 7.139
Hongzhi Wang,Chunxiao Wang,Weiguo Zhang,Suwei Yao
Developing non-noble metal catalysts with excellent electrocatalytic performance and stability is of great significance to hydrogen production by water electrolysis, but there are still problems of low activity, complex preparation and high cost. Herein, we fabricated a novel Ni 3 S 2 /Ni(OH) 2 dual-functional electrocatalyst by a one-step fast electrodeposition on nickel foam (NF). While maintaining the electrocatalytic performance of Ni 3 S 2 , the existence of heterostructure and Ni(OH) 2 co-catalyst function greatly improves the overall water splitting performance of Ni 3 S 2 /Ni(OH) 2 –NF. Hence, It shows a low overpotential of 66 mV at 10 mA cm −2 for HER and 249 mV at 20 mA cm −2 for OER. The dual-functional electrocatalyst needs only 1.58 V at 20 mA cm −2 when assembled two-electrode electrolytic cell. Impressively, the electrocatalyst also shows outstanding catalytic stability for about 800 h when 20 and 50 mA cm −2 constant current was applied, respectively which demonstrates a potential electrocatalyst for overall water splitting.
研究领域:
材料科学
·
电化学
·
能源催化
·
纳米材料
·
可持续能源
·
功能材料
·
界面化学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2022
·Vol. 48
·期 9
·3466-3477
·
IF 7.139
Zezhong Li,Jing Xu,Zhenlu Liu,Xinyu Liu,Shengming Xu,Yue Ma
The hydrothermal preparation of NiCo 2 S 4 /ZnIn 2 S 4 photocatalysts with different mass ratios is studied. Ni-cobalt bimetallic sulfide nanosheets are grown on zinc-indium bimetallic sulfide to form a compact heterojunction . First, both NiCo 2 S 4 and ZnIn 2 S 4 exhibit N-type semiconductor characteristics, a heterojunction formed by both can reduce the surface reaction energy barrier and use its synergy, strengthening the charge self-diffusion between the two semiconductors, it means the formation of a strong electric field. From the electron transfer path and band structure , NiCo 2 S 4 /ZnIn 2 S 4 has S-scheme heterojunction characteristics. NiCo 2 S 4 is a reducing photocatalyst (RP), and ZnIn 2 S 4 is an oxidative photocatalyst (OP). Under the action of built-in electric field (BIEF), strong photogenic electrons and holes exist in CB of RP (NiCo 2 S 4 ) and VB of OP (ZnIn 2 S 4 ). Thus, the overall redox capacity of the NiCo 2 S 4 /ZnIn 2 S 4 heterojunction is enhanced. Using visible light, the composite material can be used for photocatalytic hydrogen production . It is further shown that the composite material has a good effect in photocatalytic hydrogen production under the sensitizer eosin Y (EY) system. The optimal hydrogen production is about 221.75 μmol when the mass ratios of NiCo 2 S 4 /ZnIn 2 S 4 is 20%, and the photocatalytic activity of the composite is about 47 times that of ZnIn 2 S 4 . Notably, the stability of the composites is the better. A reasonable photo-catalytic mechanism is proposed based on the band gap and photoelectrochemical properties of heterojunction.
研究领域:
材料科学
·
光催化
·
能源化学
·
纳米材料
·
半导体物理
·
可持续能源
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）