Coatings
·
2023
·Vol. 13
·期 4
·714
·
IF 3.4
Su Liu,Liuxin Shi,Mengyun Liu,Wei Chen,Qiang Cheng,Xiuli Song
In recent years, textiles with antimicrobial properties have attracted more and more attention. As natural antimicrobial agents, essential oils’ potential application value lies in their ability to provide textiles with antimicrobial functions. In this paper, organic solvent extraction (n-hexane, petroleum ether, ethanol) and steam distillation were used to extract saffron petal essential oil (SPEO). It was found that organic solvent extraction (ethanol) had the highest extraction rate and the most apparent bacteriostatic effect. SPEO-Ms were prepared using the composite condensation method with gelatin and chitosan. The microstructure, encapsulation efficiency, slow-release performance, infrared spectrum, and thermal stability of the SPEO-Ms were evaluated. The results showed that the microencapsulated essential oil had good bacteriostatic properties. Antimicrobial cotton fabric was prepared by impregnating microcapsules onto cotton fibers. The effects of the microcapsules’ concentration on the whiteness, air permeability, moisture permeability, and bacteriological inhibition of the fabric were investigated. The results revealed that SPEO-Ms have the potential to be used as a new antimicrobial agent in textiles.Keywords:saffron flower petal essential oil;microcapsule;antimicrobial cotton fabric;cotton fabric
研究领域:
纺织科学
·
微生物学
·
植物化学
✓ 已验证
产品关联
DOI
高影响因子
POLYMER DEGRADATION AND STABILITY
·
2019
·
IF 3.78
Zulan Liu,Songmin Shang,Ka-lok Chiu,Shouxiang Jiang,Fangyin Dai
The electrically conductive and flame-retardant bifunctional cotton fabrics were fabricated by polymerizing pyrrole (Py) onto the cotton fabrics and followed by doping phytic acid (PA) via a chemical oxidation method. The prepared cotton fabrics were then characterized by Four-point Probes Resistivity Measurement, Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Fourier Transform Infrared Spectroscopy (FTIR), Vertical Burning Test and Thermogravimetric Analysis (TGA). The results of SEM and FTIR tests indicated that pyrrole was successfully polymerized on the cotton fabrics. The EDS measurements showed that the phosphorus increased with increasing phytic acid concentration. The results of four-point probes resistivity measurement, vertical burning test and TGA test exhibited that both the electrical conductivity and the Limit Oxygen Index (LOI) of the treated fabrics increase with increasing phytic acid concentration. The LOI of the cotton fabric increased from 18% to 37.6% after the cotton fabric was deposited with polypyrrole and doped with phytic acid. The conductivity of the treated cotton fabrics is mainly affected by the pyrrole concentration and can reach about 0.28 S cm −1 .
研究领域:
材料科学
·
纺织工程
✓ 已验证
产品关联
DOI
高影响因子
POLYMER DEGRADATION AND STABILITY
·
2019
·
IF 3.78
Shengnan Li,Ling Zhong,Shuo Huang,Dingfei Wang,Fengxiu Zhang,Guangxian Zhang
A novel flame-retardant ammonium salt of cholamine (methylenephosphonic acid) ethylene-organic phosphate acid (ACMPEP) with reactive -P O(ONH 4 ) 2 and OH groups was synthesized and characterized using nuclear magnetic resonance spectroscopy . The flame retardant not only could be grafted onto cotton fibers through P O C covalent bonds , but also react with each other to form poly-ACMPEP. The results showed that the finished cotton fabrics have excellent flame retardance, good stiffness and durability. The limiting oxygen index (LOI) value of 30% ACMPEP-treated cotton was 42.0%, and after 50 laundering cycles, the LOI value still had 30.0%. Thermogravimetric analysis (TGA) results showed that the decomposition temperature of treated cotton fibers in N 2 and air was 253 °C and 247 °C, lower than that of the control cotton fibers. Additionally, thermogravimetric-Fourier transform infrared (TG-FTIR) spectroscopy analysis indicated that the treated cotton fibers only released little combustible volatile during the thermal pyrolysis process. The cone calorimetry results showed that the heat release rate (HRR) and the total heat release (THR) of treated cottons were much lower than those of control cottons. The bending length increased 44.8% for the cotton fabric treated with 30% ACMPEP. The scanning electron microscopy (SEM) and the X-ray diffraction suggested that the finishing process only slightly affected the cotton fiber structure. The FTIR spectroscopy analysis confirmed the cross-linking reaction between ACMPEP molecules and cellulose . The tensile strengths of the finished cotton fabrics decreased a little. Together, the results suggested that the ACMPEP-treated cotton fabrics have excellent flame retardance and durability.
研究领域:
材料科学
·
纺织工程
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2024
·
IF 7.7
Huanggen Yang,Pei Zhang,Qi Zheng,Guochao Nie,Asif Hayat,Majed A. Bajaber,Saleem Raza,Duofu Li,Yan Sui
A unique combination of cotton fabric (CF) with a mixture of EDTA and APTES Fe 3 O 4 magnetic particles was developed and utilized for the first time as an adsorbent for removing pollutants from wastewater. Initially, Fe 3 O 4 was synthesized using the co-precipitation method. Further, the surface of Fe 3 O 4 was modified by introducing amino functional groups through a reaction with APTES, resulting in Fe 3 O 4 -NH 2 . Following this, the surface of carbon fiber (CF) was altered using ethylenediaminetetraacetic acid (EDTA) to create CF@EDTA. Through the use of EDC-HCl and NHS, Fe 3 O 4 -NH 2 was attached to the surface of CF@EDTA, resulting in the final product CF@EDTA/Fe 3 O 4 . Subsequently, the prepared CF@EDTA/Fe 3 O 4 was utilized to adsorb metal pollutants from wastewater, with a thorough analysis conducted using various characterization techniques including FTIR, SEM, EDX , XRD , VSM , and XPS to study the materials. The study specifically aimed to assess the adsorption performance of our cotton-based material towards As(III) and Cr 3+ metal ions. The pH study was also performed. Results indicated that the material exhibited an adsorption capacity of approximately 714 mg/g for As(III) ions and 708 mg/g for Cr 3+ ions. The Langmuir and Freundlich models, as well as pseudo-first and second-order models were also analyzed. The Langmuir and pseudo-second-order models were found to best fit the data. In terms of regeneration and reusability, the materials showed straightforward regeneration and recyclability for up to 15 cycles. The remarkable adsorption capacity, combined with the unique blend of cotton and Fe 3 O 4 magnet, along with its recyclability, positions our material CF@EDTA/Fe 3 O 4 as a promising contender for wastewater treatment and other significant areas in water research.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Materials & Interfaces
·
2019
·
IF 8.456
Sudip Kumar Lahiri,Pengcheng Zhang,Cheng Zhang,Lin Liu
Limited robustness is a serious drawback for superhydrophobic coatings and degrades the performance of superhydrophobic surfaces in practical applications. Although fluororeagents have excellent durability for superhydrophobicity, their use has been restricted due to various health and environmental concerns. In this work, we describe a facile and efficient fabrication strategy for creating robust fluorine-free superhydrophobic composite coatings that are prepared by a simple dip-dry method, in which the H3BO3-incorporated SiO2–alkyl-silane coatings are deposited on woven cotton fabric surfaces followed by polydimethylsiloxane modification. The coated surface shows a large water contact angle of 157.95 ± 2° and a small sliding hysteresis angle (SHA) of 3.8 ± 0.6°, demonstrating excellent superhydrophobicity. The coated fabric surface also exhibited robustness and durability, withstanding a tape-peeling test (under 48.05 kPa) for around 80 repetitions and sandpaper rubbing (loaded 100 g) for 40 cycles. Furthermore, the coated fabric surface displayed self-healing and oil–water separation capacities. The developed superhydrophobic coatings in this study are robust, environmentally benign, and easy to fabricate, showing promising applications in textile industries.
研究领域:
材料科学
·
纺织工程
·
表面化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FIBERS AND POLYMERS
·
2018
·Vol. 19
·期 5
·1024-1031
·
IF 1.353
Lei Wenwen,Sun Yufa,Huang Bin,Zhou Xiangdong
The polyurethane modified organic silicone (PU-SA) was successfully synthesized via step-by-step polymerization with isophorone diisocyanate (IPDI) and polypropylene glycol (PPG) used as monomers, dibutyltindilaurate (DBTDL) as the catalyst, trimethylolpropane (TMP) and N-methyldiethanolamine (MDEA) as the chain extender, and amino-terminated siloxane (SA) as the blocking agent. The chemical structure of PU-SA was characterized by Fourier transform infrared spectroscopy (FT-IR). X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) showed that PUSA had been successfully finished on the surface. Additionally, the thermogravimetric analysis (TGA) demonstrated that the PU-SA treated fabrics showed low decomposition temperature and slightly high char residue. As a finishing agent, the effect of PU-SA on the handle of cotton fabrics was also studied by using a Kawabata Evaluation System for Fabrics (KES-F). The experimental results found that PU-SA had a significant improvement on the bending properties, surface properties, and compressional properties. Moreover, the mechanical and anti-wrinkle properties of the cotton fabrics were also enhanced.
研究领域:
材料科学
·
纺织工程
·
高分子化学
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2020
·Vol. 44
·期 8
·3504-3513
·
IF 3.288
Qingqing Zhou,Jiayi Chen,Tianchi Zhou,Jianzhong Shao
A flame-retardant conductive cotton fabric switch was successfully prepared by the in situ polymerization of polyaniline doped with novel phytic acid (PA) by impregnation in an ice water bath for 24 h. The surface morphology, chemical composition, and thermal properties of the fabric before and after the in situ polymerization of polyaniline with PA were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), thermogravimetric analysis (TG), and TG-FTIR. The experimental results demonstrated that the limiting oxygen index (LOI) of the original fabric increased to 32% and the sheet resistance (Rs) decreased to 1.13 kΩ □−1. Under the PA de-doped state, the fabric had no flame-retardant and conductivity properties. Nevertheless, the excellent flame-retardant and conductivity properties of the fabric were obtained once more after re-doping with PA, which indicated that the flame-retardant and conductive textile switch was prepared successfully. Remarkably, the variation in the P content by XPS and the characteristic absorption peak of PA by FTIR made the doping behavior of PA on the surface of different fabrics clear. During the pyrolysis of the original and finished fabric, the maximum decomposition temperature (Tmax) and the maximum emission (Te) of light gas decreased from 380 °C to 290 °C, and the carbon residue content increased from 12.6% to 39.2% at 700 °C, which indicated that the in situ polymerization of aniline doped with PA resulted in the superior flame-retardant property of the fabric. This work provides a green method and basis for the preparation of multi-functional textiles, thus improving the added value of textiles.
研究领域:
材料科学
·
纺织工程
✓ 已验证
产品关联
DOI
高影响因子
TEXTILE RESEARCH JOURNAL
·
2022
·
IF 2.455
Huizhen Ke,Qin Fang,Yitong Han,Huanda Zheng,Laijiu Zheng,Yuanyuan Dong
Traditional water-based flame-retardant finishing causes serious pollution due to the use of a large number of chemicals, and color change is easily generated since the flame-retardant finishing takes place after the cotton dyeing. An eco-friendly flame-retardant finishing of dyed cotton was explored using 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO), 2,2′-oxybis-(5,5-dimethyl-1,3,2,-dioxaphosphorinane-2,2′-disulfide) (5060), SiO2, DOPO/SiO2 (1:1), 5060/SiO2 (1:1) and DOPO/5060 (1:1) in supercritical CO2. The effects of finishing time and pressure as well as temperature on the flame-retarding properties of the cotton were discussed. As expected, samples with the higher weight gain rates exhibit a lower after-flame time as well as after-glow time. In different flame-retardant systems, cotton fabric finished with DOPO presents the lowest after-flame time of 20.6 s and after-glow time of 0 s at 130°C, 22 MPa and 120 min due to its biphenyl ring and O=P-O bond. Moreover, tiny fluctuations of L*, a*, b* and K/S values occurred from 32.10 to 34.24, 5.78 to 6.05, –37.89 to –37.64 and 10.59 to 10.81 when the cotton samples were treated with DOPO, 5060, SiO2, DOPO/SiO2 (1:1), 5060/SiO2 (1:1) and DOPO/5060 (1:1), proving that no significant negative role in the color property of the samples occurs after supercritical CO2 finishing.
研究领域:
纺织科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
MOLECULES
·
2023
·Vol. 28
·期 7
·3175
·
IF 4.6
Xiaolei Song,Congzhu Xu,Wendong Yao,Jieyun Wen,Qufu Wei,Yonggui Li,Xinqun Feng
Magnetic protective fabrics with fine wearability and great protective properties are highly desirable for aerospace, national defense, and wearable protective applications. The study of the controllable preparation method of Nd3+doped in Fe3O4nanoparticles with supposed magnetic properties remains a challenge. The characterization of the microstructure, elemental composition, and magnetic properties of NdFe2O4nanoparticles was verified. Then, the surface of NdFe2O4was treated with glyceric acid to provide sufficient –OH. Subsequently, the connection of the nanoparticle by the succinimide group was studied and then grafted onto cotton fabrics as its bridging effect. The optimal loading rate of the functional fabrics with nanoparticles of an average size of 230 nm was 1.37% after a 25% alkali pretreatment. The color fatness to rubbing results showed better stability after washing and drying. The corresponding hysteresis loop indicated that the functional fabrics exhibited typical magnetism behavior with a closed “S” shape and a magnetic saturation value of 17.61 emu.g−1with a particle size of 230 nm. However, the magnetic saturation value of the cotton fabric of 90 nm was just 4.89 emu.g−1, exhibiting controllable preparation for the aimed electromagnetic properties and great potential in radiation protective fields. The electrochemical properties of the functional fabrics exhibited extremely weak electrical conductivity caused by the movement of the magnetic dipole derived from the NdFe2O4nanoparticles.Keywords:NdFe2O4nanoparticles;grafting;cotton fabric;magnetic protective
研究领域:
材料科学
·
纺织工程
·
电磁学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2023
·
IF 5.2
Xiaoye Bi,Dong Xue,Yunpeng Wang,Chencheng Lv,Zexiong Li,Tao Zhao
This research aims to develop a durable and formaldehyde-free flame retardant treatment for cotton fabrics. Phosphorous acid (PA) is employed in conjunction with urea and guanidine carbonate to chemically bond the flame retardant to the cellulose fibers of the fabric. The treated fabrics are evaluated for their flame resistance, comfort, breathability, aesthetics, fire performance, carbon residue, limiting oxygen index, thermal stability, combustion behavior, and fabric properties. The results demonstrate successful grafting of PA onto cotton fabrics, leading to enhanced flame resistance while maintaining the desired fabric characteristics. The treated fabrics exhibit improved fire performance with increased carbon residue from 4.03% to 28.19% and higher LOI values from 18.0% to 43.5%. Moreover, the thermal stability of the fabric is enhanced, resulting in altered combustion behavior characterized by reduced the total heat release from 11.1 kJ/g to 0.1 kJ/g. Importantly, the flame-retardant treatment does not significantly impact the wettability or stiffness of the fabric. This study presents a simple and effective approach to produce highly efficient fire-resistant cotton fabrics, holding promise for various applications where fire safety is a concern.
研究领域:
材料科学
·
纺织工程
·
消防安全
✓ 已验证
产品关联
DOI
高影响因子
FIBERS AND POLYMERS
·
2016
·Vol. 17
·期 2
·305-309
·
IF 1.022
Yu Yalun,Cai Muyuan,Zhou Lan,Shao Jianzhong
The accumulation and autoxidation of residual oily soil from human sebum is regarded as a major reason for the aging and yellowing of clothing and household textiles. In this study, the yellowing degree of cotton fabrics soiled with human sebum components and aged under various environmental conditions (various temperatures, humidities and light intensities etc.) were investigated. The representative sebum components including olive oil, squalene, oleic acid and cottonseed oil were selected and their chemical changes were studied by FTIR analysis. The results showed that, olive oil, squalene, oleic acid and cottonseed oil could caused more significant fabric-yellowing than other components in human sebum, and the yellowing degree could become higher with increasing temperatures, humidities and/or light intensities of aging environments. The chemical structures of olive oil, squalene and oleic acid changed remarkably after aging treatment. The aging products contained hydroxyl groups and carbonyl groups, and the conjugated C=O group was considered to be the chemical species leading to the yellowing of sebum-soiled fabrics.
研究领域:
纺织科学
·
生物化学
✓ 已验证
DOI
高影响因子
Journal of Natural Fibers
·
2021
·
IF 5.323
Xu Meng,YANYAN Dong,WEISHOU Tan,YINGCHAO Xia,Liping Liang
The cotton fabric is esterified with a carboxylic acid (4-azidobenzoic acid) having an azide group to obtain a cotton fabric with an azide group on the surface. Then, the hydrophobic group-containing substance (1-heptyne) was modified on the surface of the cotton fabric through click chemistry, and a cotton fabric with super-hydrophobic and super-lipophilic properties was prepared. Scanning electron microscope (SEM), Fourier transform infrared spectrometer (FTIR), thermogravimetric/differential thermal analyzer (TG), and contact angle measuring instrument were used to characterize the surface morphology and hydrophobicity of the cotton fabric. The effect of pore size on the efficiency of oil-water separation was explored. The results show that the prepared cotton fabric has super-hydrophobic and super-lipophilic properties with a contact angle of up to 154.1°, and it has been successfully applied to oil/water separation. Even for different oil/water mixtures, the separation efficiency was better than 94% on average. The large pore size is beneficial to improve the efficiency of oil-water separation.
研究领域:
材料科学
·
纺织工程
·
化学工程
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）