INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2019
·
IF 4.784
Xiujuan Zhao,Yangyang Luo,Peixin Tan,Mingxian Liu,Changren Zhou
A high-performance oil-water separation device that built by environment-friendly materials is a promising strategy to solve water pollution problem. In this study, we developed an oil-water separation system with chitin/halloysite nanotubes (C/HNTs) composites. C/HNTs were crosslinked by epichlorohydrin and freeze-dried, then a porous sponge was formed. The C/HNTs sponge was modified to be hydrophobic via immersing into bromohexadecane ethanol solution. The surface structure, mechanical properties, microstructure, oil absorption and oil-water separation ability of the C/HNTs sponge were investigated. The addition of HNTs significantly increased the compressive strength of chitin sponge without influence on porous structure . IR spectra indicated the successful coating of bromohexadecane on the C/HNTs sponge surface, which enabled the hydrophobicity and lipophilicity of this construct. The inside construct of the C/HNTs sponges were full of interconnected pores, and the pore size ranged from 250 to 500 μm. The absorption capability for various oil and grease were measured, including methylbenzene, sunflower seed oil , carbon dichloride, n-hexane, chloroform and acetone. It is found that the total amount of chloroform absorbed by a C/HNTs sponge was ~11.23 times of the sponge's weight, and the absorption for hexane was ~3.94 times of the sponge's weight. The sponge also exhibited an excellent oil-water separation ability with as high as 98.7% separation efficiency. All the results suggested that the chitin/HNTs sponges with improved mechanical property would have a great potential in oil-water separation.
研究领域:
材料科学
·
环境工程
·
高分子化学
·
纳米复合材料
·
分离技术
✓ 已验证
DOI
高影响因子
JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY
·
2019
·
IF 3.571
Xu Xu,Fuhao Dong,Xinxin Yang,He Liu,Lizhen Guo,Yuehan Qian,Aiting Wang,Shifa Wang,Jinyue Luo
The absorbent materials synthesized from biosources with low cost and high selectivity for oils and organic solvents have attracted increasing attention in the field of oil spillage and discharge of organic chemicals. We developed a convenient surface-grafting method to prepare efficient and recyclable biobased aerogels from epoxidized soybean oil (ESO)-modified cellulose at room temperature. The porous network-like structure of the cellulose aerogel was still fully retained after undergoing hydrophobic modification with ESO. Moreover, the modified aerogels possessed excellent hydrophobicity with a water contact angle of 132.6°. Moreover, the absorbent ability of the hydrophobic cellulose aerogels was systematically assessed. The results showed that modified aerogels could retain more than 90% absorption capacity even after 30 absorption–desorption cycles, indicating that the ESO-grafted cellulose aerogels have practical applications in the oil–water separation from industrial wastewater and oil-leakage removal.
研究领域:
材料科学
·
环境工程
·
化学工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2019
·
IF 4.784
Quan-Yong Cheng,Xiao-Li Zhao,Yi-Dong Li,Yun-Xuan Weng,Jian-Bing Zeng
Traditional superhydrophobic cotton fabrics (SCFs) for oil/water separation were usually fabricated by surface coating with inorganic nanoparticles combined with nonrenewable and nonbiodegradable or even toxic fossil-based chemicals, which would lead to secondary environmental pollution after their lifetime. In this study, we report robust, nanoparticle-free, fluorine-free SFC, which was prepared by acid etching followed by surface coating with epoxidized soybean oil resin (CESO) and subsequent modification with stearic acid (STA). No toxic compound and no nanoparticle were included within the SCF and all the raw materials including cotton fabric, CESO and STA are biodegradable and derived from biological resources. The SCF showed excellent mechanical stability and chemical/environmental resistances. The superhydrophobicity of the SFC survived from mechanical abrasion , tape peeling, ultrasonication , solvent erosion and low/high temperature exposure. The SCF also exhibited good acid/alkali resistance with contact angle over 150° toward different pH water droplets. Moreover, the SCF could efficiently separate oil/water mixtures with efficiency above 97.9% and the superhydrophobicity remained after reusing for at least 10 times. The fully biological-derived SCF with excellent mechanical and chemical resistances exhibit great potential for separation of oil/water mixtures.
研究领域:
材料科学
·
环境工程
·
高分子化学
·
表面科学
·
可持续技术
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 139
·期 17
·52018
·
IF 3.125
Xianggui Zhang,Xianglong Li,Antuo Wang,Bin Yang,Teng Hou,Yishen Lu,Jing Zhou
The separation of stable oil/water emulsions is an urgent global issue. In this work, a porous and superhydrophobic polytetrafluoroethylene (PTFE) fibrous membrane was obtained by first centrifugal spinning PTFE/potato starch fibers and then heat treating the fibers to remove the starch. Results showed that spherical protrusions and irregular striped protrusions appeared on the surface of the prepared PTFE fibers, which significantly increased the roughness and hydrophobicity of the fibrous membrane. In addition, number density and shapes of these protrusions could be tuned by changing the extent of the heat treatment and the potato amylose content during the fiber preparation. The water contact angle on the structured PTFE membranes was as high as 160°, and the water sliding angle was as low as 3.4°. The results of oil/water separation experiments showed that the oil removal rate reached 99.5% based a permeability of 3670 L/m 2 /h, which suggested that the obtained PTFE fibrous membrane has great potential for use in oil/water emulsions separation.
研究领域:
材料科学
·
环境工程
·
膜分离技术
·
表面科学
·
化学工程
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2019
·
IF 4.784
Shaojie Zhang,Chao Yu,Na Liu,Yun Teng,Cuiyu Yin
In this study, cellulose pulp and urea were used to synthesize cellulose carbamate (nitrogen content reaches 4.5%) by low-cost and environmentally friendly solid-liquid phase method. Cellulose carbamate fluid was prepared by using sodium hydroxide aqueous solution as solvent. The fluid was regenerated and formed in a coagulation bath , and finally a regenerated cellulose membrane with high transparency and separation ability was obtained. The simple chemical treatment of cellulose not only greatly increased the mass fraction of cellulose dissolution (It has reached 15%) and retains the original crystal form and thermal stability of cellulose. The surface of the membrane was relatively dense, and the inside has regular microchannel . The factors affect the transparency and water flux of regenerated cellulose membranes were discussed by orthogonal experimental range analysis. The ability of the regenerated cellulose membrane to reject dyes was tested. The results showed that the rejection of methyl blue and congo red reached 100%, and the rejection rate of methyl orange reached 60%. The oil/water separation ability and the anti-pollution ability of the regenerated cellulose membrane were tested. The oil/water separation effect reached 100%. This membrane may have application prospect in water treatment, biotechnology.
研究领域:
材料科学
·
环境工程
·
膜技术
·
高分子化学
·
水处理
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2018
·
IF 5.091
Zanru Guo,Hongjian Gu,Qiang Chen,Zhanfeng He,Wenyuan Xu,Jiali Zhang,Yongxin Liu,Leyan Xiong,Longzhen Zheng,Yujun Feng
Hypothesis The effective separation and recovery of oils from water is important for the protections of ecosystems and the environment. Polymeric porous monoliths have been demonstrated as attractive absorbents for oil/water separation. However, the recyclability was mainly realized by squeezing, combustion, or centrifugation, which may restrict in elastic materials, destroy the adsorbates or need special apparatus. Thus it is desirable to developing monoliths with controllable oil absorption and desorption. Experiments A series of “smart” monoliths with pH-induced switchable wettability were fabricated by high internal phase emulsion (HIPE) polymerization and epoxide ring-opening for the incorporation of amine groups. The resultant monoliths and their wettabilities were examined using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), nitrogen adsorption/desorption and contact angle analysis, respectively. The oil separation efficiency and recyclability were evaluated. Findings The monoliths with macroporous structure can undergo switchable wettability under reversible pH stimulation. As an absorbent, the monoliths not only separated and recovered organic solvents and oils (including crude oil) from aqueous mixtures through a reversible and recyclable absorption and desorption process upon alternating the pH between 7.0 and 1.0, but also continuously expulsed oils from water surfaces in a continuous manner with the aid of external driving pressures. Moreover, the monoliths also allowed the effective separation of surfactant-free and surfactant-stabilized oil-in-water emulsions with high separation efficiency.
研究领域:
环境科学
·
高分子材料
·
分离科学
·
界面化学
·
功能材料
✓ 已验证
DOI
高影响因子
RSC Advances
·
2017
·Vol. 7
·期 55
·34461-34465
·
IF 3.108
Tingting Zheng,Ang Li,Zhanying Li,Wenbin Hu,Lin Shao,Lingbin Lu,Yang Cao,Yongjun Chen
As an environmentally friendly aerogel with outstanding performances, the improvement of mechanical properties is urgently required for cellulose aerogel development. In this study, a cellulose aerogel with good mechanical properties was successfully fabricated using nanocrystalline cellulose (NCC) as reinforcer. Characterization results demonstrated that NCC was embedded well into the cellulose aerogel. Tests and evaluation showed that the compressive modulus of the NCC reinforced cellulose aerogel was significantly improved, about 6 times higher than that of the pure cellulose aerogel. Furthermore, after modification with trimethylchlorosilane via a cold plasma treatment, the NCC reinforced aerogel became hydrophobic but its oleophilic property remained. This aerogel showed good adsorption capacity, reached saturation rapidly and possessed good reusability. Reinforced mechanical properties with NCC make this cellulose aerogel a very promising material for highly efficient separation and extraction of organic pollutants and oils from water.
研究领域:
材料科学
·
高分子化学
·
环境功能材料
·
纳米复合材料
·
绿色材料
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2018
·
IF 2.906
Bo Lin,Jian Chen,Zeng-Tian Li,Fu-An He,De-Hao Li
In this work, the fluoroalkylsilane-modified SiO 2 nanoparticles (NPs) were immobilized on the polyurethane sponges by a highly efficient drop-coating method using different polymers including poly(vinylidene fluoride), poly(vinylidene fluoride-ter-trifluoroethylene-ter-chlorotrifluoroethylene), polystyrene , and polyurethane as the adhesives to achieve the superhydrophobic modification of the polyurethane sponges for oil-water separation. The successful fluoroalkylsilane modification for the SiO 2 NPs was confirmed by TEM, SEM , FITR, XPS, and TGA. Furthermore, the surface-modified polyurethane sponges were investigated by SEM and two-dimensional EDS mapping. The contact angles of the surface-modified polyurethane sponges were in the range of 151.6°–154.3°, which confirmed the realization of the superhydrophobic modification for the polyurethane sponges. The demonstration experiments showed that the resulting surface-modified polyurethane sponge could effectively remove oil from the oil-water mixture by direct absorption or gravity-driven filtration. Moreover, the surface-modified polyurethane sponges possessed not only high absorption capability for different oils including peanut oil, pump oil, and silicone oil but also good reusability . We believe that such novel surface-modified polyurethane sponges might be potential candidates for the oil-water separation.
研究领域:
材料科学
·
环境工程
·
纳米技术
·
表面化学
·
分离科学
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Chao Yang,Jun Yang,Ge Song,Limin Zang,Qifan Liu,Jianhui Qiu,Xue Yang,Chun Wang
Oil/water separation has recently attracted a great deal of attention for research due to the frequent occurrence of an oil spill as well as the increase of industrial and household oily wastewater. Therefore, the purpose of this study is to demonstrate underwater superoleophobic crosslinked phosphorylated poly(vinyl alcohol) hydrogel coated stainless steel mesh (CL-PPVA@SSM), which was fabricated using a simple dip-coating method and aldol reaction on the mesh substrate. The as-prepared CL-PPVA@SSM is capable of separating oil from a variety of different oil/water mixtures with high separation efficiency up to 99.2%, excellent recyclability and fast water permeate flux of 467.7 L m –2 h –1 , which makes it suitable for the separation of oil-water mixtures from oil-water emulsions. Also, in the oil-water separation process, the CL-PPVA@SSM is capable to remove organic dye from the water. The CL-PPVA@SSM exhibits stability under various harsh conditions such as mechanical abrasion. Importantly, the CL-PPVA@SSM shows a massive potential to separate kitchen waste oil/water mixtures due to the underwater superoleophobic property as required for the recycling of kitchen waste oil. Therefore, this method has been met with a promising application prospect of practical application.
研究领域:
材料科学
·
环境工程
·
高分子化学
·
表面工程
·
化学工程
·
纳米技术
·
水处理技术
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）