COMBUSTION SCIENCE AND TECHNOLOGY
·
2013
·
IF 1.011
Ming-Di Li,Zhong Wang,Yang Zhao,Rui-Na Li,Shuai Liu
An experimental study was reported on premixed ethanol/n-heptane/oxygen/argon flames at low pressure (4.655 kPa) with ethanol blending ratios of 0 (Flame 1), 15% (Flame 2), and 30% (Flame 3). The equivalence ratio was 1.0. Flame species were identified using molecular beam mass spectrometry with tunable synchrotron photoionization. The flame temperature profiles were measured with a Pt-6%Rh/Pt-30%Rh thermocouple. The mole fraction profiles of major and intermediate flame species under different ethanol ratios were analyzed in this article. Experimental results showed that the temperature profiles of measured flames fall almost on a single curve, which means that ethanol had little effect on flame temperature. The peak mole fraction of the main combustion products occurred 2–6 mm above the burner. With the increase of ethanol blending ratios, the mole fractions of H2, CO, and CO2 decreased, the mole fraction of H2O increased, and the mole fractions of intermediate combustion products (C2H2, C2H4, HCHO, C3H3) decreased. During the combustion process, the oxygen atom of ethanol partly replaces the O2, thus the final mole fraction of O2 increased with the increase of ethanol ratios.
研究领域:
化学工程
·
燃烧学
✓ 已验证
产品关联
DOI
高影响因子
OPTICS EXPRESS
·
2023
·Vol. 31
·期 5
·8098-8109
·
IF 3.8
Jia Wang,Jia Wang,Jia Wang,Xiaojian Hao,Xiaojian Hao,Xiaojian Hao,Baowu Pan,Xiaodong Huang,Xiaodong Huang,Haoliang Sun,Haoliang Sun,Pan Pei,Pan Pei
Existing non-contact flame temperature measuring methods depend on complex, bulky and expensive optical instruments, which make it difficult for portable applications and high-density distributed networking monitoring. Here, we demonstrate a flame temperature imaging method based on a perovskite single photodetector. High-quality perovskite film epitaxy grows on the SiO2/Si substrate to fabricate the photodetector. Duo to the Si/MAPbBr3 heterojunction, the light detection wavelength is extended from 400 nm to 900 nm. Then, a perovskite single photodetector spectrometer has been developed using the deep-learning method for spectroscopic measurement of flame temperature. In the temperature test experiment, the spectral line of doping element K+ has been selected to measure the flame temperature. The photoresponsivity function of the wavelength was learned based on a commercial standard blackbody source. The spectral line of element K+ has been reconstructed using the photocurrents matrix by the regression solving photoresponsivity function. As a validation experiment, the “NUC” pattern is realized by scanning the perovskite single-pixel photodetector. Finally, the flame temperature of adulterated element K+ has been imaged with the error of 5%. It provides a way to develop high precision, portable, low-cost flame temperature imaging technology.
研究领域:
材料科学
·
光学工程
·
人工智能
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Omega
·
2024
·
IF 3.7
Xijin Wang,Zhitao Liu,Qian Chen,Jing Yang,Yao Zhu,You Fu,Yiming Ma,Feiyun Chen,Xin Liao
The development of high energy gun propellants faces significant challenges in terms of erosion, partly due to the inadequate effectiveness of erosion inhibitors. In this paper, the influence of quite different flame temperature of five gun-propellants on erosion-reducing efficiency of four representative inhibitors materials (talc/TiO2/ PDMS/Paraffin) were studied in vented erosion vessel tester. From aspects of morphologies and element compositions of erode steel samples, as well as the pressure and heat generated by propellant burning, the relevant erosion-reducing processes and mechanisms were discussed. The results indicated that erosion inhibitors should be appropriately selected according to the type of gun propellant. The erosion of gun propellants having extremely high flame temperature of 3810 K were hardly reduced using talc, TiO2, and PDMS inhibitors, which can generate numerous solid particles aggravating the melt-wipe process. While paraffin exhibits a uniquely positive erosion-reducing efficiency for the gun propellant having a flame temperature of 3810 K, that was attributed to the mitigated melt-wipe process. The inference was further supported by the high-volume cooling gas, resulting from the higher burning pressure of propellants loading with paraffin and excellent heat absorption capacity of paraffin tested with propellants having higher propellant flame temperature. The obtained results indicated that the factors of flame temperature of gun propellants should be taken into the design and composition optimization of an effective inhibitor. This work could provide potential reference for the development of future novel inhibitors, which serves as high energy gun propellants.
研究领域:
材料科学
·
燃烧学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
OPTICS EXPRESS
·
2017
·Vol. 25
·期 20
·A932
·
IF 3.307
Fan Yang,Xiaoli Kang,Jiangshan Luo,Laixi Sun,Handing Xia,Zao Yi,Yongjian Tang
We report the first laser emission from flash ignition of Zr/Al nanoparticles with the addition of strong oxidizer KClO4 using Nd: YAG as a laser medium. The mixture Zr/Al/Kp-45 (mass ratio = 33%Zr: 33%Al: 34%KClO4) has the highest brightness temperature Tb = 4615 K and the adiabatic flame temperature Tf = 4194 K with the duration of 20 ms. At 1064 nm we measured a maximum output energy of 702.5 mJ with the duration of nearly 10 ms by using only 100 mg mixture with an output coupler (transmission T = 10%). Further optimizing the concentration cavity and increasing the mixture content will yield much higher efficiency and output energy.
研究领域:
材料科学
·
光学
·
激光物理
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FIBERS AND POLYMERS
·
2024
·Vol. 25
·期 4
·1177-1191
·
IF 2.2
Peng Hao,Song Xiaolan,Song Dan,Wang Yi,An Chongwei,Luo Chunwang
The nano-boron powder (n-B) exhibits remarkable efficacy as a combustion catalyst, making it a prime candidate for use in solid propellant metal burners. Nevertheless, throughout the storage phase, the surface of n-B powder is prone to oxidation and substantial agglomeration, resulting in challenges with ignition and incomplete energy dissipation when utilizing boron powder. The synthesis of nano-boron/nitrocellulose/ammonium dinitramide@fluorine rubber (n-B/NC/ADN@F 2602 ) is accomplished via the coaxial electrospinning technique, with n-B uniformly dispersed within the core–shell fiber. The n-B is evenly distributed within the core–shell fiber, and as a result of F 2602 encapsulation, the moisture absorption of n-B/NC/ADN@F 2602 has decreased from 191.6 to 10.1%. In the course of combustion, the fibrous composite of n-B/NC/ADN@F 2602 undergoes an escalation in the rates of energy output and energy release, owing to the constraints imposed by external F 2602 . The n-B/NC/ADN@F 2602 demonstrates a 1.3-fold rise in peak pressure and a 1.15-fold increase in maximum pressure rise rate compared to n-B/NC/ADN. Furthermore, the maximum flame temperature is elevated by 150.5 ℃, and the combustion heat is augmented by approximately 8.7%. The findings of the energy performance assessment reveal that the mean molecular weight (MC) of the combustion byproduct of n-B/NC/ADN@F 2602 stands at 27.6 g·mol −1 , markedly surpassing that of n-B/NC/ADN. The aforementioned findings exemplify that coaxial electrospinning is an exceedingly efficacious technique for enhancing nanostructures, thereby amplifying the reactivity of energetic particles and offering novel insights into their application in energetic materials.
研究领域:
材料科学
·
纳米技术
·
燃烧工程
·
高分子科学
·
含能材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）