JOURNAL OF POWER SOURCES
·
2016
·
IF 6.333
Gang Peng,Xiayin Yao,Hongli Wan,Bingxin Huang,Jingyun Yin,Fei Ding,Xiaoxiong Xu
An insightful study on the fundamental lithium storage behavior of all-solid-state lithium battery with a structure of LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA)/Li 10 GeP 2 S 12 /Li-In is carried out in this work. The relationship between electrochemical performances and particle size, surface impurities and defects of the NCA positive material is systematically investigated. It is found that a ball-milling technique can decrease the particle size and remove surface impurities of the NCA cathode while also give rise to surface defects which could be recovered by a post-annealing process. The results indicate that the interfacial resistance between the NCA and Li 10 GeP 2 S 12 is obviously decreased during the ball-milling followed by a post-annealing. Consequently, the discharge capacity of NCA in the NCA/Li 10 GeP 2 S 12 /Li-In solid-state battery is significantly enhanced, which exhibits a discharge capacity of 146 mAh g −1 at 25 °C.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态离子学
·
电池技术
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2018
·
IF 5.116
Chuankai Fu,Shuaifeng Lou,Yi Cao,Yulin Ma,Chunyu Du,Pengjian Zuo,Xinqun Cheng,Weiping Tang,Yongmin Wu,Yunzhi Gao,Hua Huo,Geping Yin
Recently, rechargeable lithium metal polymer battery (LMPB) attracts increasing attention because of its high safety and energy density properties. However, the high contact interfacial resistance of solid-state electrode and electrolyte is still an obstacle to satisfy the demand of high current density and long cycle stability, especially at room and lower temperature. Here, we develop a simple and efficient heat treatment method, to improve the interfacial compatibility between electrode and electrolyte in all-solid-state LMPB, successfully realizing workable LMPB at a reduced temperature (30 °C). The LMPB shows excellent cycling performance and rate capability in the voltage range of 2.5–4.2 V. The behavior of Li + plating/stripping on the surface of lithium metal anode is greatly enhanced. Meanwhile, the interfacial resistance of the LMPB decrease significantly after the heat treatment process .
研究领域:
材料科学
·
电化学
·
能源存储
·
固态电池
·
界面工程
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·Vol. 51
·期 8
·10774-10782
·
IF 5.1
Jitao Yi,Xinyue Zhang,Shanliang Chen,Ting Sun,Qinghui Jiang,Yong Liu
BiCuSeO-based materials show great promise for thermoelectric generators in waste heat recovery due to their excellent thermoelectric properties. However, the limited focus on device development has hindered their industrial-scale implementation. Here, high-performance BiCuSeO-based compounds with exceptional thermal stability were synthesized and remained stable aging for 400 h, making them suitable for investigation in the device bonding process. The BiCu80AgP is identified as the optimal solder from eight candidates, effectively connecting the copper (Cu) electrode with BiCuSeO-based compounds. The optimized bonding process substantially resulted in an impressive interfacial shear strength of about 15 MPa and reduced interfacial resistance to 2.2 mΩ cm 2 . Interface analysis revealed the formation of diverse, complex compounds, with variations in their concentrations greatly affecting joint performance. Achieving a uniform distribution of these compounds effectively mitigated thermal expansion mismatches and extended joint longevity by a factor of 6.6. This research proposes a novel fabrication method for BiCuSeO-based thermoelectric devices utilizing BCu80AgP solder, providing a foundation for future advancements in this field.
研究领域:
材料科学
·
热电转换
·
固态物理
·
能源材料
·
界面工程
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2016
·Vol. 41
·期 22
·9611-9618
·
IF 3.205
Jinhua Xiao,Wenying Zhang,Chunyan Xiong,Bo Chi,Jian Pu,Li Jian
Spinel oxides with the general formula of MnCu x Co 2−x O 4 (x = 0.1, 0.3, 0.5, 0.7 respectively) are used as coating materials on the metallic interconnect SUS 430 alloy to reduce the cathodic performance degradation by Cr poisoning and the interfacial resistance to improve the surface stability. The effect of Cu doping at the B position of spinel on the electrical conductivity and coefficient of temperature expansion (CTE) is investigated to determine the oxidation behavior and effectiveness as a protective layer. The result confirms that MnCu 0.5 Co 1.5 O 4 spinel shows highest electrical conductivity of 105.46 S cm −1 at 750 °C in air and an average CTE value of 12.27 × 10 −6 K −1 at temperature range of 20–960 °C. MnCu 0.5 Co 1.5 O 4 coating is stable enough after 2000 h cyclic oxidation at 750 °C. The growth of Cr 2 O 3 and formation of MnCr 2 O 4 in the scale layer are effectively suppressed by the presence of MnCu 0.5 Co 1.5 O 4 coating. The oxidation kinetics obeys the parabolic law with a rate constant as low as 2.76 × 10 −15 g 2 cm −4 ·s −1 and the ASR contributed by the oxide scale is 8.04 mΩ cm 2 at 750 °C. The research indicates that MnCu 0.5 Co 1.5 O 4 is a promising coating material for metallic interconnects of the intermediate temperature solid oxide fuel cells .
研究领域:
材料科学
·
能源材料
·
固体氧化物燃料电池
·
表面工程
·
电化学
·
高温腐蚀
·
功能涂层
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）