INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2019
·
IF 4.784
Xiujuan Zhao,Yangyang Luo,Peixin Tan,Mingxian Liu,Changren Zhou
A high-performance oil-water separation device that built by environment-friendly materials is a promising strategy to solve water pollution problem. In this study, we developed an oil-water separation system with chitin/halloysite nanotubes (C/HNTs) composites. C/HNTs were crosslinked by epichlorohydrin and freeze-dried, then a porous sponge was formed. The C/HNTs sponge was modified to be hydrophobic via immersing into bromohexadecane ethanol solution. The surface structure, mechanical properties, microstructure, oil absorption and oil-water separation ability of the C/HNTs sponge were investigated. The addition of HNTs significantly increased the compressive strength of chitin sponge without influence on porous structure . IR spectra indicated the successful coating of bromohexadecane on the C/HNTs sponge surface, which enabled the hydrophobicity and lipophilicity of this construct. The inside construct of the C/HNTs sponges were full of interconnected pores, and the pore size ranged from 250 to 500 μm. The absorption capability for various oil and grease were measured, including methylbenzene, sunflower seed oil , carbon dichloride, n-hexane, chloroform and acetone. It is found that the total amount of chloroform absorbed by a C/HNTs sponge was ~11.23 times of the sponge's weight, and the absorption for hexane was ~3.94 times of the sponge's weight. The sponge also exhibited an excellent oil-water separation ability with as high as 98.7% separation efficiency. All the results suggested that the chitin/HNTs sponges with improved mechanical property would have a great potential in oil-water separation.
研究领域:
材料科学
·
环境工程
·
高分子化学
·
纳米复合材料
·
分离技术
✓ 已验证
DOI
高影响因子
RSC Advances
·
2017
·Vol. 7
·期 55
·34461-34465
·
IF 3.108
Tingting Zheng,Ang Li,Zhanying Li,Wenbin Hu,Lin Shao,Lingbin Lu,Yang Cao,Yongjun Chen
As an environmentally friendly aerogel with outstanding performances, the improvement of mechanical properties is urgently required for cellulose aerogel development. In this study, a cellulose aerogel with good mechanical properties was successfully fabricated using nanocrystalline cellulose (NCC) as reinforcer. Characterization results demonstrated that NCC was embedded well into the cellulose aerogel. Tests and evaluation showed that the compressive modulus of the NCC reinforced cellulose aerogel was significantly improved, about 6 times higher than that of the pure cellulose aerogel. Furthermore, after modification with trimethylchlorosilane via a cold plasma treatment, the NCC reinforced aerogel became hydrophobic but its oleophilic property remained. This aerogel showed good adsorption capacity, reached saturation rapidly and possessed good reusability. Reinforced mechanical properties with NCC make this cellulose aerogel a very promising material for highly efficient separation and extraction of organic pollutants and oils from water.
研究领域:
材料科学
·
高分子化学
·
环境功能材料
·
纳米复合材料
·
绿色材料
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2018
·
IF 2.906
Bo Lin,Jian Chen,Zeng-Tian Li,Fu-An He,De-Hao Li
In this work, the fluoroalkylsilane-modified SiO 2 nanoparticles (NPs) were immobilized on the polyurethane sponges by a highly efficient drop-coating method using different polymers including poly(vinylidene fluoride), poly(vinylidene fluoride-ter-trifluoroethylene-ter-chlorotrifluoroethylene), polystyrene , and polyurethane as the adhesives to achieve the superhydrophobic modification of the polyurethane sponges for oil-water separation. The successful fluoroalkylsilane modification for the SiO 2 NPs was confirmed by TEM, SEM , FITR, XPS, and TGA. Furthermore, the surface-modified polyurethane sponges were investigated by SEM and two-dimensional EDS mapping. The contact angles of the surface-modified polyurethane sponges were in the range of 151.6°–154.3°, which confirmed the realization of the superhydrophobic modification for the polyurethane sponges. The demonstration experiments showed that the resulting surface-modified polyurethane sponge could effectively remove oil from the oil-water mixture by direct absorption or gravity-driven filtration. Moreover, the surface-modified polyurethane sponges possessed not only high absorption capability for different oils including peanut oil, pump oil, and silicone oil but also good reusability . We believe that such novel surface-modified polyurethane sponges might be potential candidates for the oil-water separation.
研究领域:
材料科学
·
环境工程
·
纳米技术
·
表面化学
·
分离科学
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 139
·期 12
·51827
·
IF 3.125
Yuan Li,Lu Zhang,Fayong Li,Ke Wang,Xiaoru Wu,Hailu Liu,Bibo Long,Yang Zhao,Dong Xie,Junjia Chen
The hydrophobic modification of cellulose nanofibers (CNF) was carried out via free radical polymerization using methyl methacrylate (MMA) as the monomer to improve the compatibility between CNF and poly lactic acid (PLA). Followed by the preparation of the novel nanocomposites in combination of the organic montmorillonite and the substrate. The resulting nanocomposites were then coated on paper surface using a cast-coating process in an attempt to improve the barrier properties towards water vapor and oxygen. In addition, the composite films are prepared via a solution casting method. The water vapor transmission rate (WVTR), water vapor permeability (WVP), oxygen transmission rate (OTR), and tensile strength of the as-prepared films were systematically measured. The corresponding results demonstrated that the WVTR, WVP and OTR decreased with the addition of a certain content of MCNF in coatings. 0.2 wt% MCNF is the optimum content, showing the best gas resistance and tensile performance. The lowest value of WVTR and WVP are 10.30 g/(m 2 ⋯24 h) and 3306.58 g⋯μm/(m 2 ⋯24 h) for films with 0.2 wt% MCNF added, which is 88.23% and 26.05% lower than that of PLA composite film without NFC.
研究领域:
高分子材料
·
纳米复合材料
·
包装材料
·
表面涂层
·
生物基材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）