JOURNAL OF MEMBRANE SCIENCE
·
2024
·
IF 8.4
Yingbo Li,Jing Ma,Hongjun Lin,Cheng Chen,Saleam Raza,Qianqian Zeng,Xinchun Lu,Liguo Shen
The development of composite membranes utilizing transition metal carbides and nitrides, exemplified by Ti 3 C 2 T x (MXene), has proven efficacious in the treatment of oily wastewater. However, challenges arise from the prolonged and convoluted transport paths within MXene interlayer nanochannels, significantly impeding mass transfer and diminishing membrane permeability. This investigation incorporated porous covalent organic frameworks (COFs) as intercalating agents into two-dimensional (2D) MXene-based membranes to expand the interlayer nanochannels. The resulting MXene@COF-TpBD functional layer polyethersulfone (PES) composite membrane exhibited a distinctive dual superoleophobic surface, concurrently manifesting underwater superoleophobicity and underoil superhydrophobicity (underwater oil contact angle >150°, underoil water contact angle >150°). The membranes exhibited excellent water flux (up to 4092.7 L m −2 h −1 ·bar −1 ), efficient oil-water emulsion separation (up to 1908.4 L m −2 h −1 ·bar −1 , rejection rates >99.78 %), noteworthy fouling resistance and structural stability, outperforming most of existing similar membranes. Furthermore, supported by the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, the incorporation of COF-TpBD improved the antifouling characteristics of the composite membrane. This work presents innovative insights into the improvement of 2D MXene membranes and the use of COF-TpBD for the specific remediation of oily wastewater.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
NANOTECHNOLOGY
·
2024
·Vol. 35
·期 30
·305703
·
IF 2.9
Lang Liu,Wei Wang,Ye Hong
Membrane distillation technology could utilize low-grade heat to desalinate brine, but the membrane material often suffers from disadvantages of low permeation flux and weak robustness to contaminants. To address these issues, the commercial polytetrafluoroethylene (PTFE) membrane was modified by cost-effective chemicals of tannic acid and (3-Aminopropyl)-triethoxysilane (APTES) to construct hydrophilic/underwater superoleophobic nano-rough structures on the surface to enhance its flux and oil-fouling resistance in direct contact membrane distillation. The results show that a high underwater oil contact angle of 180° is observed to the membrane surface due to the rough nanostructures functionalized by abundant hydroxyl groups. Despite the additional mass transfer resistance provided by the rough nanostructures, the flux was increased noticeably. This is mainly attributed to the strong interactions between the abundant hydroxyl groups of hydrophilic layer surface and water molecules, leading to a part of free water staying at intermediate transition state (IW). The mass transfer resistance of the hydrophilic layer itself is reduced as a consequence of decreased evaporation enthalpy of water, thereby increasing the flux. Moreover, while the flux of the pristine membrane is reduced by 84.18%, the flux of Janus membrane remains the same when treating mineral oil brine emulsions with oil concentration up to 1500 ppm in comparison with the result for 35 g l−1 brine solution, indicating that the Janus membrane is safe from the oil contamination. Our work provides a fine guidance for membrane distillation to treat high oily brine.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MATERIALS SCIENCE AND TECHNOLOGY
·
2017
·
IF 1.538
Sirong Yu,Hao Li
In this work, a simple method, including electrodeposition and chemical modification, for fabrication of a superhydrophobic and oleophobic coating on steel substrate is reported. The surface morphology of this coating showed concave structure, and the contact angles of water and glycerol on this coating surface were about 153.57° and 149.32°, respectively. In addition, the water droplet was easy to roll on this coating surface, and the sliding angle was smaller than 10°. The contact angle of the water/ethanol droplet with different surface tension, from 56 to 36 mN m−1, was also >130° on this coating surface, indicating this as superhydrophobic and oleophobic coating surface with good lyophobicity. Moreover, this coating surface had excellent non-sticking property for the water droplet under a certain external pressure, self-cleaning property and long-term stability.
研究领域:
材料科学
·
表面工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POLYMER SCIENCE PART A-POLYMER CHEMISTRY
·
2016
·Vol. 54
·期 13
·2040-2049
·
IF 3.114
Tao Qian,Juanjuan Wang,Tiantian Cheng,Xiaoli Zhan,Qinghua Zhang,Fengqiu Chen
The poly(methyl methacrylate) -b- poly(2-[[[[2-(perfluorohexyl)]-sulfonyl]-amino]ehthyl] methacrylate) (PMMA -b- PC 6 SMA) copolymers were successfully synthesized for the first time using activator regenerated by electron transfer atom transfer radical polymerization (ARGET ATRP) method. Under optimized reaction conditions, the degree of polymerization (DP) of resulting copolymers increased approximately linearly with monomer conversion. Structures of a well-defined block copolymer were determined by GPC, FT–IR, and 1 H-NMR spectra. Results from AFM and contact angle measurements of polymer films revealed the presence of block segments derived from PC 6 SMA, as indicated by the obvious increase in hydrophobicity and oleophobicity. The relationship between surface composition and surface wetting ability was confirmed by XPS and AFM spectra. Compared with the random copolymer PMMA -co- PC 6 SMA, C 6 SMA dosages in the PMMA -b- PC 6 SMA copolymers were greatly decreased, which retained its hydrophobic and oleophobic properties. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54 , 2040–2049
研究领域:
高分子化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2023
·
IF 8.6
Zehao Chen,Ting Zhao,Qing Tan,Jihao Zuo,Shouping Xu,Yunjun Nong,Xiufang Wen,Pihui Pi
The crude oil spillage and large-scale industrial release of oily effluents has led to significant ecological degradation and resource wastage. Traditional superwetting materials encounter intractable challenges for treating surfactant-stabilized oil–water emulsions, including trade-off effect of permeation flux and separation efficiency, and low emulsion processing life. These issues considerably impede advancements in oil–water separation industry. In order to enhance the demulsification durability of materials while ensuring high separation efficiency and flux, this work doped perfluorooctanoic acid (PFOA) onto the modified sponge surface with superhydrophilic charged surface, and a unique in-air superhydrophilic-oleophobic sponge was prepared. This special surface allows rapid water phase permeation yet offers remarkably more stable oleophobicity compared with traditional underwater oleophobic materials when processing a large amount of emulsions. The intrinsic oleophobicity endows the sponge outstanding fouling resistance and greatly increases the one-cycle emulsion treatment amount up to 1695 L·m −2 . Moreover, the sponge's inherent long permeation channels and surface charge maintain a high separation efficiency of over 97 %. The large pores of the sponges and superhydrophilic surface provide a high permeation flux exceeding 40,000 L·m −2 ·h −1 . The sponge with high separation efficiency, flux, and capacity marks a significant advancement, offering a promising strategy for superwetting material applications in oil-in-water emulsion separation fields.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2024
·
IF 8.1
Qian Xiang,Yan Liu,Bo Wang,Chengyi Huang,Lilin Wang,Jinsong He,Dong Tian,Fei Shen,Yanzong Zhang
To realize efficient treatment of oily wastewater, various super-wetting materials have been developed. Oily wastewater is often complex and may contain both oil-in-water and water-in-oil emulsions. However, most of the current studies focus on the treatment of single emulsions, and there are fewer studies on the simultaneous separation of oil-in-water and water-in-oil emulsions. In this paper, by removing hemicellulose and lignin from bamboo processing waste powder (BPWP), the treated bamboo powder (TBP) containing mainly cellulose was obtained. TBP has superoleophobicity underwater and superhydrophilicity underoil, which can separate not only various oil-in-water emulsions stabilized by surfactants, but also water-in-oil emulsions stabilized by different surfactants, and the separation efficiency is higher than 99 %. The separation efficiencies of TBP for different water-in-oil emulsions were all higher than 99 %. On this basis, we have established an intelligent device that makes full use of underwater super-hydrophobic and under-oil super-hydrophilic properties to realize the purification of water and de-watering and recycling of floating oil in complex oil-water systems. This work provides a very promising direction for industrial application in practical oily wastewater treatment and fuel recovery.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2024
·
IF 6.3
Guoxin Zhu,Xiong Zhang,Yan He
Oily wastewater produced from various industries and oil spills has posed serious threats to the environment and human health. Promisingly, superwetting materials emerge as great candidates for efficient oil/water separation. In this work, a superhydrophilic-superoleophobic melamine sponge was prepared using a facile immersion method. Methyltrimethoxysilane (MTMS) was used as a binder, which combined fluorosurfactant (FS-50) and TiO 2 onto the sponge surface. The coated sponge displayed a water contact angle of 0° and an oil contact angle of 154.5°. Accordingly, it exhibited absorption capacities of above 86 g/g for water and under 1 g/g for oils. Based on its selective permeability and 3D porous structures, the coated sponge could continuously separate various immiscible oil/water mixtures and oil-in-water emulsions with separation efficiencies larger than 99.4 % and 98.7 %, respectively. Notably, the superhydrophilic-superoleophobic sponge was extended to present opposite wettability towards polar and nonpolar liquids. Consequently, it achieved continuous separation of immiscible oil/oil mixtures, with separation efficiency over 99.1 %. Additionally, the coated sponge displayed excellent reusability, great mechanical stability against compression and abrasion, and stable separation performance for various harsh oil/water mixtures. The study presented a promising separation candidate for future applications in oily wastewater treatment and other liquid/liquid separation fields.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
Journal of Water Process Engineering
·
2024
·
IF 6.3
Shusu Shen,Qifeng Fan,Honglin Li,Lunbo Xu,Ganwei Zhang,Renbi Bai
Developing a stable MOF-modified membrane for efficient treatment of oily wastewater remains a challenge. In this study, NH 2 -MIL-88B(Fe) (NM88B) was deposited on the commercial polyvinylidene fluoride (PVDF) membranes, and grafted with perfluorohexane-1-sulfonic acid potassium salt (PFHx) to achieve quaternization modification. This reaction proceeds in an environmentally friendly manner due to the absence of any catalyst. The introduction of fluorine atoms through grafting PFHx resulted in the modified PVDF membrane (NPF) demonstrating remarkable underwater superoleophobic property with an underwater oil contact angle at ∼180°. In separation of various oil-water emulsions, the NPF membrane afforded a high permeation flux (up to 2043 L·m −2 ·h −1 ) and rejection rate (∼99 %). The oil rejection of NPF membrane was >99 % after 10 filtration cycles of n -hexadecane-water emulsion, and the pure water flux of the recovered membrane was kept at 82.65 % of the original flux, indicating a very good reusability and stability. Filtration of mixed dye/oil-water emulsions showed that the NPF membrane remove 99 % of both oil and dye from the mixture. This work provides a simple and stable modification of PVDF membrane, exhibiting remarkable underwater superoleophobicity and hydrophilicity , thereby harboring substantial prospects in the treatment of oily wastewater.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY
·
2024
·
IF 5.9
Yan Liu,Yanhong Wu,Hongchun Chen,Rujing He,Hong Xiao,Chengyi Huang,Xiaojing Wang,Zhenxing Zeng,Jinsong He,Yanzong Zhang
At present, there are few studies on the removal of water from oil, but water in fuel can cause machine malfunctions and even safety accidents, which cannot be ignored. In this study, an oil-resistant superhydrophilic/air superoleophobic sponge (SS-MS) was designed to selectively absorb water from oil. Through layer by layer deposition, polyphenols, particles, and fluorinated surfactants were assembled on the sponge, finally achieving the effect of super hydrophilic and super oil phobic in the air. The contact angle of the modified sponge SS-MS on diesel oil can reach 153°, and the absorption efficiency of water in diesel oil can reach more than 99 %. Moreover, a continuous selective absorption device for water in oil was constructed, the SS-MS sponge can still achieve a water absorption efficiency of 98 % after ten cycles. Importantly, the SS-MS has excellent mechanical and chemical stability under 80 % strain, different pH, UV irradiation times and temperatures. In addition, the materials used in this study are all green and low-pollution substances, and melamine sponge has the advantages of low price, light weight, good elasticity and high porosity. In summary, SS-MS offers a new approach to remove water from fuel and has the potential for large-scale applications.
研究领域:
材料科学
·
环境工程
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2019
·
IF 7.015
Wei Zhang,Yubing Lu,Jun Liu,Xipeng Li,Baoan Li,Shichang Wang
Superhydrophobic and oleophobic membrane applied in membrane distillation was fabricated by constructing a re-entrant composite structure via immobilizing silica nanoparticles (NPs) on the polyvinylidene fluoride (PVDF) membrane. The silica coated membrane with the assistance of polydopamine (PDA) was then fluorosilanized by means of a silane coupling agent 1H,1H,2H,2H-perfluorooctyltrichlorosilane. A series of characterizations were implemented to investigate the effects of modification process on the structure and performance of the PVDF composite membranes . The fouling and wetting behaviors of original and modified membranes were explored by direct contact membrane distillation (DCMD) tests using a mixed solution of inorganic salts, organic matter and surfactant as the feed. The results indicated that silica NPs and fluorinated silane were presented on the PVDF membrane substrate. After surface modification, the liquid entry pressure (LEP) increased by 120%, in addition, the water contact angle (WCA) increased from 127.0° to 169.0°, and the oil contact angle (OCA) increased from 2.8° to 112.1°. The modification process showed no effect on the pore size and pore structure . Furthermore, the composite membrane exhibited excellent chemical stability and prominent mechanical stability. The re-entrant structure resulting from nanoparticles and microspheres and the omniphobic feature were conferred on the composite membrane. The DCMD tests showed that the composite membrane kept a stable permeate flux in the long-term concentration experiment, with the salt rejection rate approximately 100%. What's more, the composite membrane did not suffer from fouling and wetting, and still dry and clean after the test. In comparison, the pristine membrane was seriously polluted during the test, and the permeate flux decreased to 28.3% of the initial value. Overall, the novel modified PVDF composite membrane reported in this work presents outstanding anti-fouling performances.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
Journal of Water Process Engineering
·
2022
·
IF 7.34
Lin Chen,Fangqing Li,Longjie Jiang,Fudong He,Yufei Wei
Polytetrafluoroethylene (PTFE) hydrophobic membranes used in direct contact membrane distillation (DCMD) processes were prone to fouling and wetting by oil and surfactants, which hampered their broad industrial application. In this work, a new Janus composite membrane was developed by modifying UiO-66-NH 2 with polyvinyl alcohol (PVA) as a cross-linking agent and immobilizing the modified UiO-66-NH 2 on the PTFE membrane by vacuum filtration. By tuning the ratio of PVA to MOF , an optimally proportioned Janus membrane was obtained, and its performance was tested in DCMD experiments through the use of a sodium chloride feed solution containing hexadecane and sodium dodecyl sulfate. The top layer of this Janus membrane exhibited underwater oleophobicity (130.1 ± 0.96°) and hydrophilicity in the air (54.0 ± 0.92°), while the bottom layer is hydrophobic (132.3 ± 0.97°). Compared to the pristine PTFE membrane, the modified Janus membrane demonstrated promising resistance to both membrane fouling and wetting of oils and surfactants. The desalination rate of 99.99% was still achieved within 24 h with the conductivity remaining lower than 10 μS/cm and the flux maintained at 21.3 L/(m 2 ·h). As a result, the Janus composite membrane developed in this study was shown to be a prospective alternative for treating wastewater containing oily substances and surfactants in a resourceful manner.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2016
·Vol. 18
·期 36
·25394-25400
·
IF 4.449
Yuqi Li,Hui Zhang,Mizi Fan,Jiandong Zhuang,Lihui Chen
Oil–water separation has recently become an important subject due to the increasing incidence of oil spills. Materials with underwater superoleophobic properties have aroused considerable interest due to their cost-effectiveness, environmental friendliness and anti-fouling properties. This paper presents a robust salt-tolerant superoleophobic aerogel inspired by seaweed used without any further chemical modification for oil–seawater separation. The green aerogel is prepared by freeze-drying of sodium alginate (SA)–nanofibrillated cellulose (NFC) using Ca2+ ions as the crosslinking agent. The three-dimensional (3D) interconnected network structure of the developed aerogel ensures its high mechanical strength and good flexibility. The natural hydrophilicity of the polysaccharides contained in the aerogel ensures its excellent underwater superoleophobicity, antifouling and salt-tolerance properties. More impressively, the as-prepared aerogel can even keep its underwater superoleophobicity and high hydrophilicity after being immersed in seawater for 30 days, indicating its good stability in marine environments. Furthermore, the aerogel could separate oil–seawater mixtures with a high separation efficiency (of up to 99.65%) and good reusability (at least 40 cycles). The facile and green fabrication process combined with the excellent separation performance and good reusability makes it possible to develop engineering materials for oil–water separation in marine environments.
研究领域:
材料科学
·
环境科学
·
海洋科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）