JOURNAL OF MEMBRANE SCIENCE
·
2018
·
IF 6.578
Jianfeng Li,Shujuan Guo,Zhaozan Xu,Jianguo Li,Zihe Pan,Zhiping Du,Fangqin Cheng
In order to reduce the wetting and fouling propensity of polyvinylidene fluoride (PVDF) membrane during coking wastewater treatment by membrane distillation, two kinds of omniphobic PVDF composite membranes were prepared by coating SiO 2 nanoparticles on PVDF membrane surface via electrostatic adsorption or chemical bonding respectively, and subsequently fluorination. The coated SiO 2 nanoparticles observed as amounts of nano-scale protrusions by scanning electron microscope constructed a re-entrant structure and enhanced membrane surface roughness . The omniphobicity of the modified membranes was confirmed by high contact angles (> 150°) for water, diiodomethane and ethylene glycol on the membrane surface. The omniphobic layer with SiO 2 nanoparticles coated via chemical bonding was more stable than electrostatic adsorption. Both the omniphobic PVDF membranes exhibited stable and high rejections of the inorganic and organic contaminants, which were determined by conductivity, total organic carbon and three-dimensional excitation-emission fluorescence spectroscopy of the distillate. The modified omniphobic membranes also showed much less flux decline than the pristine PVDF membrane in direct contact membrane distillation tests (120 h), suggesting their excellent anti-fouling performance. This study indicates that coating silica nanoparticles via chemical bonding is an effective and promising method to fabricate omniphobic PVDF membrane for coking wastewater treatment.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2016
·Vol. 42
·期 6
·7767-7773
·
IF 2.758
Shuangbing Li,Jixiao Wang,Song Zhao,Wei Cai,Zhi Wang,Shichang Wang
The unmodified and 3-(trimethoxysilyl) propyl methacrylate (TPM) modified silica nanoparticles were synthesized via the modified Stöber method. The structure and chemical composition of silica nanoparticles were determined by scanning electron microscope (SEM), X-ray diffraction (XRD) characterization, Fourier Transform Infrared Spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The results demonstrate that silica nanoparticles with the diameter of 90 nm and amorphous state are successfully modified by TPM. The rheological test results demonstrated that surface modification of nanoparticles and medium exerted great influence on the rheological properties of silica particle suspension. Under high shear rate of about 250 s −1 , the viscosity of suspension comprising unmodified silica nanoparticles and deionized water , TPM-modified silica nanoparticles and deionized water, TPM-modified silica nanoparticles and polyethylene glycol , is about 0.4 Pa.s, 0.1 Pa.s and 30 Pa.s, respectively. The results are significant for preparing homogenous and stable silica nanoparticle suspension, and meaningful for ceramic processing .
研究领域:
材料科学
·
纳米技术
·
陶瓷加工
·
胶体化学
·
高分子材料
✓ 已验证
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2011
·
IF 2.13
Xin Tian,Zhengping Dong,Yifan Huang,Jiantai Ma
In this work, molecular logic element modified multifunctional silica nanoparticles having high magnetization have been successfully prepared. These multifunctional nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), Elementary analysis, X-ray powder diffraction (XRD) and Vibrating sample magnetometer (VSM). The characterization datum indicated that the organic ligand was successfully grafted on the surface of the magnetic silica nanoparticles . The fluorescent changes of the hybrid material upon the addition of cations (H + , F − and their mixture) is utilized as an INHIBIT logic gate at the molecular level, using the fluorescence intensity signal as output.
研究领域:
纳米医学
·
生物传感器
·
分子诊断
·
化学生物学
·
智能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
·
2016
·Vol. 33
·期 3
·261-265
·
IF 2.267
Shuangbing Li,Jixiao Wang,Song Zhao,Wei Cai,Zhi Wang,Shichang Wang
The spherical silica particles in narrow size distribution with different diameters of 90 nm, 200 nm, 320 nm and 400 nm were prepared by the modified Stöber method and characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and dynamic light scattering (DLS). The phase composition of particles was characterized by X-ray diffraction. The results indicated that each of the silica particle samples was in amorphous state. The shear thickening fluids (STFs) comprising 53 vol.% of silica particles and 47 vol.% of polyethylene glycol with molecular weight of 200 g mol −1 (PEG200) were prepared and evaluated. The influence of size and size distribution on the critical shear rate and the intensity of shear thickening were analyzed. The STFs prepared by silica nanoparticles with a diameter of 90 nm showed the giant rheological effect with the critical shear rate of 2.51 s −1 , the largest viscosity of 45,500 Pa∙s and the yield stress of 181 kPa. The experiments and the analysis results demonstrated that the suspensions prepared by nanoparticles have high intensity of shear thickening.
研究领域:
胶体化学
·
流变学
·
纳米材料科学
·
软物质物理
·
功能材料
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2016
·
IF 3.15
Qiang Huang,Meiying Liu,Junyu Chen,Ke Wang,Dazhuang Xu,Fengjie Deng,Hongye Huang,Xiaoyong Zhang,Yen Wei
Surface modification of nanomaterials with polymers is an effective route to render new functions and improve the performance of the final nanocomposites. Here, a facile method was developed to fabricate polyacrylic acid (PAA)-grafted monodisperse SiO 2 nanoparticles (SiO 2 -PDA-PAA) through a combination of mussel inspired chemistry and Michael addition reaction. To obtain the products, the SiO 2 nanoparticles were first coated with polydopamine (PDA) through self-polymerization of dopamine under rather mild conditions. The PDA thin films can then be further conjugated with amino-terminated PAA, which was synthesized by chain transfer free radical polymerization using cysteamine hydrochloride as a chain transfer agent and acrylic acid as a monomer. The SiO 2 -PDA-PAA nanocomposites were characterized via transmission electron microscopy, Fourier transform infrared spectroscopy, thermal gravimetric analysis, and X-ray photoelectron spectroscopy. The effects of contact time, solution pH, temperature and methylene blue (MB) concentration on the removal of MB were investigated. The results demonstrated that SiO 2 -PDA-PAA showed significant improvement in adsorption efficiency towards MB. The kinetics and isotherm studies showed that pseudo-second-order and Langmuir isotherm models were well fitted the experimental data. The values of thermodynamics parameters such as entropy change ( ΔS 0 ), enthalpy change ( ΔH 0 ) and Gibbs free energy ( ΔG 0 ) were calculated based on the Van’t Hoff equation. The negative values of thermodynamic parameters indicated that the adsorption of MB was a feasible, spontaneous and exothermic process. In summary, we developed a facile method to fabricate SiO 2 -based polymer nanocomposites, which showed obviously enhanced adsorption capability towards MB.
研究领域:
材料科学
·
环境化学
·
纳米技术
·
高分子化学
·
胶体与界面化学
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2019
·Vol. 136
·期 36
·47922
·
IF 2.188
Nan Pan,Juanrong Qin,Yuwei Fan,Zeke Li,Botao Song
In this study, mesoporous silica nanoparticles (MSNs) were embedded into the hydrophilic poly(vinyl alcohol) (PVA) nanofibrous mats to achieve sustained release of water soluble drug from hydrophilic nanofibrous mats. MSNs were successfully prepared based on a sol–gel method. Water soluble drug naproxen sodium was then loaded into the mesopores of the MSNs, and different amounts of the drug-loaded MSNs were further incorporated into the fibers by the electrospinning process. Morphology of the nanofibrous mats was investigated, and it was found that all the fibers exhibited fibrous structure. Interestingly, lots of protrusions could be observed from the scanning electron microscopy images with high magnification, and numbers of the protrusions increased with the increasing of loading ratios of the MSNs from 5 to 15%. In addition, the wetting behaviors of the nanofibrous mats were also measured, and the water contact angles of all the mats were measured to be 0°. Finally, the drug release results indicated that all the PVA/MSNs composite nanofibrous mats showed an obviously prolonged drug release. The optimal loading ratio of the MSNs in the nanofibers was 10% due to the slowest drug release rate. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136 , 47922.
研究领域:
药剂学
·
生物材料
·
纳米医学
·
药物递送系统
·
高分子科学
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2016
·Vol. 27
·期 7
·7265-7273
·
IF 1.798
Zhang Dongjiu,Cheng Haifeng,Zhang Zhaoyang,Kang Yue
This paper introduced a general method of etching suspended graphene by nonmetallic SiO x nanoparticles (SiO x NPs) in graphene synthesis. Effects of etching time, concentration of silica gel and type of graphene on the etching mode of graphene have been systematically considered with using as-grown graphene film on a silica gel coating copper as model system. Nonmetallic SiO x NPs acted as etchant plays important role in the in situ etching process during the fabrication of graphene. The etched multilayer graphene pattern can be modulated from large area films to a rectangle pattern by varying the Si concentration and etching time, while single layer graphene pattern alters little. The morphology and critical structure of SiO x etched graphene were characterized by Raman spectra, transmission electron microscopy, scanning electron microscope and X-ray photoelectron spectrum. The process and mechanism described here open the way for tailoring graphene via nanoparticles instead of metal, which show significant influence of the electrical properties of graphene.
研究领域:
纳米材料学
·
表面科学
·
凝聚态物理
·
材料化学
·
电子显微学
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2018
·
IF 2.906
Bo Lin,Jian Chen,Zeng-Tian Li,Fu-An He,De-Hao Li
In this work, the fluoroalkylsilane-modified SiO 2 nanoparticles (NPs) were immobilized on the polyurethane sponges by a highly efficient drop-coating method using different polymers including poly(vinylidene fluoride), poly(vinylidene fluoride-ter-trifluoroethylene-ter-chlorotrifluoroethylene), polystyrene , and polyurethane as the adhesives to achieve the superhydrophobic modification of the polyurethane sponges for oil-water separation. The successful fluoroalkylsilane modification for the SiO 2 NPs was confirmed by TEM, SEM , FITR, XPS, and TGA. Furthermore, the surface-modified polyurethane sponges were investigated by SEM and two-dimensional EDS mapping. The contact angles of the surface-modified polyurethane sponges were in the range of 151.6°–154.3°, which confirmed the realization of the superhydrophobic modification for the polyurethane sponges. The demonstration experiments showed that the resulting surface-modified polyurethane sponge could effectively remove oil from the oil-water mixture by direct absorption or gravity-driven filtration. Moreover, the surface-modified polyurethane sponges possessed not only high absorption capability for different oils including peanut oil, pump oil, and silicone oil but also good reusability . We believe that such novel surface-modified polyurethane sponges might be potential candidates for the oil-water separation.
研究领域:
材料科学
·
环境工程
·
纳米技术
·
表面化学
·
分离科学
✓ 已验证
DOI
高影响因子
JOURNAL OF MOLECULAR LIQUIDS
·
2019
·
IF 4.561
Xiao-Qian Wei,Wan-Ju Zhang,Lu Lai,Ping Mei,Li-Mei Wu,Yan-Qun Wang
The effects of cationic surfactants on the properties of Pickering emulsions stabilized by silica nanoparticles (nano-SiO 2 ) were investigated. The zeta potential , three-phase contact angle ( θ ), and dynamic interfacial tension (DIT) were measured to analyze the interaction between hydrophilic nano-SiO 2 and four different cationic surfactants (i.e., dodecyltrimethylammonium bromide [DTAB], bis-quaternary ammonium salts [BQAS-12], multiple quaternary ammonium salts [MQAS-12], and dimethyldioctadecylammonium bromide [DDAB-18]). All these surfactants can naturally improve the stability of Pickering emulsions induced by hydrophilic nano-SiO 2 . The nano-SiO 2 /MQAS-12 mixtures exhibited the best ability to stabilize the O/W emulsions, followed by nano-SiO 2 /BQAS-12 mixtures. The nano-SiO 2 /DDAB-18 mixtures can induce emulsion inversion from O/W to W/O. All emulsions exhibited excellent salt tolerance and acid-base resistance properties. Determining the zeta potential showed that nano-SiO 2 had the highest negative charge at the pH of 9.5. Thus, the surfactant molecules can be adsorbed remarkably on the nano-SiO 2 surface. Modification with different cationic surfactants can significantly increase the θ value of nano-SiO 2 , but the bilayers for DTAB-12, BQAS-12, and MQAS-12, except for DDAB-18, were adsorbed. DIT curves indicated that competitive adsorption of the surfactants occurred between the oil/water interface and nano-SiO 2 surface. The competitive adsorption of MQAS-12 was stronger than those of BQAS-12 and DTAB-12. The nano-SiO 2 /DDAB-18 mixture had an apparent induction region and required a considerable amount of time to reach equilibrium. The modified nano-SiO 2 was also not adsorbed in the oil/water interface spontaneously, which may be due to the large size of particles compared with small surfactant molecules.
研究领域:
胶体与界面化学
·
纳米材料科学
·
乳液工程
·
物理化学
·
表面科学
✓ 已验证
DOI
高影响因子
Small
·
2024
·Vol. 20
·期 24
·2308304
·
IF 13
Weiqun Li,Chucheng Luo,Jimin Fu,Juan Yang,Xiangyang Zhou,Jingjing Tang,B. Layla Mehdi
Lithium–ion batteries (LIBs) has been developed over the last three decades. Increased amount of silicon (Si) is added into graphite anode to increase the energy density of LIBs. However, the amount of Si is limited, due to its structural instability and poor electronic conductivity so a novel approach is needed to overcome these issues. In this work, the synthesized chromium silicide (CrSi 2 ) doped Si nanoparticle anode material achieves an initial capacity of 1729.3 mAh g −1 at 0.2C and retains 1085 mAh g −1 after 500 cycles. The new anode also shows fast charge capability due to the enhanced electronic conductivity provided by CrSi 2 dopant, delivering a capacity of 815.9 mAh g −1 at 1C after 1000 cycles with a capacity degradation rate of <0.05% per cycle. An in situ transmission electron microscopy is used to study the structural stability of the CrSi 2 -doped Si, indicating that the high control of CrSi 2 dopant prevents the fracture of Si during lithiation and results in long cycle life. Molecular dynamics simulation shows that CrSi 2 doping optimizes the crack propagation path and dissipates the fracture energy. In this work a comprehensive information is provided to study the function of metal ion doping in electrode materials.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
固体物理
·
计算材料学
✓ 已验证
DOI
高影响因子
BIOCHEMICAL AND BIOPHYSICAL RESEARCH COMMUNICATIONS
·
2018
·
IF 2.559
Peng Zhang,Menghuan Tang,Qin Huang,Guanjian Zhao,Ning Huang,Xiang Zhang,Ying Tan,Yuan Cheng
Mesoporous silica nanoparticles (MSNPs) of a small diameter were loaded with the anticancer drug temozolomide (TMZ), coated with polydopamine (PDA), and conjugated with Asn-Gly-Arg (NGR) for use in the treatment of glioma. The accumulation of NGR-MSNPs in C6 cells was shown to be higher than that of unmodified MSNPs. Anticancer drugs can cause autophagy in tumor cells, whereas autophagy inhibitors can block this reaction and enhance the therapeutic effect of the drugs. In this study, we demonstrated that MSNP-TMZ-PDA-NGR had stronger autophagy- and apoptosis-inducing effects in C6 cells than TMZ alone, and its anticancer effect was further enhanced when combined with autophagy inhibition. These results demonstrate that the combination of targeting vehicles and autophagy inhibitors may have research value in the treatment of gliomas.
研究领域:
纳米技术
·
药学
·
肿瘤学
·
细胞生物学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）