JOURNAL OF ELECTROANALYTICAL CHEMISTRY
·
2016
·
IF 2.822
Yanmeng Cai,Yue Wang,Xinyu Han,Liwen Zhang,Shichang Xu,Jixiao Wang
The composites of carbon nanotube (CNT) and the conducting polymer polypyrrole (PPy) doped with dodecyl benzene sulfonate (DBS − ) and Cl − were prepared respectively by chemical oxidation method and made into two types of composite electrode (PPy-DBS/CNT and PPy-Cl/CNT) for capacitive deionization (CDI) cell. Enhanced electrochemical performance of the composite electrodes was confirmed by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) test. The results of CV showed that the specific capacitance of PPy/CNT doped with either DBS − or Cl − was about 2.3–2.5 times that of the CNT electrode. And EIS test demonstrated that the charging resistance for both the PPy-DBS/CNT and PPy-Cl/CNT electrodes was dramatically reduced and only about 10% that of the CNT electrode. By pairing the two composite electrodes with CNT electrodes, four cells were assembled to study the effects of electrode assembling patterns on the desalination performance of the CDI process. The results indicated that the CDI cells involving either the PPy-DBS/CNT electrode or the PPy-Cl/CNT electrode, or both of them exhibited much higher electrosorption capacity (from 40.8 to 72.36 mg/g) than that of the CDI cell assembled with two CNT electrodes (about 12.6 mg/g). And the composite electrodes kept good stability and fast regeneration rate after several desalting cycles. Thus, it is believed that the enhanced performance and optimized electrode assembly of the CDI cell should be with the composite electrodes that have the good ability of ion selective adsorption for cations or anions.
研究领域:
材料科学
·
环境工程
·
电化学
·
水处理技术
·
功能高分子材料
✓ 已验证
DOI
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2024
·Vol. 130
·期 11
·835
·
IF 2.5
Kou Chen,Duan Bin,Shi Lichun,Yang Hongcai,Ni Heng,Wang Haiyuan,Ye Qing,Hu Junshan,Hu Shigang
The Sc 3+ ions doped NaYF 4 : Yb 3+ , Er 3+ upconversion (UC) nanoparticles are synthesized by thermal decomposition method. We successfully obtained the upconversion luminescence (UCL) nanoparticles from green emission to red emission through doping Sc 3+ ions with different concentrations. Based on the XRD, the phase change process of Sc 3+ ions doped NaYF 4 nanocrystalline phase were demonstrated. More importantly, through the analysis of UC spectrum data, the change in the phase of the NaY/ScF 4 : Yb 3+ , Er 3+ nanocrystalline corresponds to the change in its luminous properties. It determines that the change of crystal field will lead to the change of luminescence, and then modulate the luminescence. NaScF 4 : Yb 3+ , Er 3+ UC nanoparticles exhibit strong red light emission. In addition, the temperature-sensitive properties of the optimal doping concentration of Sc 3+ ion were tested. The sensitivity of NaYF 4 : Yb 3+ , Er 3+ nanoparticles doped with Sc 3+ ion reached the maximum value of 0.024 K − 1 at 498 K. The nanocrystalline has great application value in the fields of optical temperature measurement, biomedicine, bioprobes and colorful display.
研究领域:
材料科学
·
光学工程
·
生物医学工程
·
纳米技术
·
分子影像学
✓ 已验证
DOI
高影响因子
BULLETIN OF MATERIALS SCIENCE
·
2016
·Vol. 39
·期 1
·187-193
·
IF 0.895
CAO RENPING,QIN ZHENGDONG,JIANG SHENHUA,LIANG AIHUI,LUO ZHIYANG,YU XIAOGUANG
A series of CaNb 2 O 6 : x Sm 3+ (0 ≤
x
≤ 10 mol%) and CaNb 2 O 6 : Sm 3+ , Na + /B 3+ phosphors were synthesized by the solid-state reaction method in air. Their crystal structures and luminescence properties were investigated and analysed, respectively. Host CaNb 2 O 6 emitted blue light with excitation 270 nm. CaNb 2 O 6 : x Sm 3+ phosphors showed a systematically varied hue from blue to white by changing Sm 3+ ion concentration from 0 to 10 mol% with excitation of 270 nm and their chromaticity coordinates were the regions from (0.1665, 0.1767) to (0.2484, 0.2260). Luminescence properties of CaNb 2 O 6 : Sm 3+ phosphor were tuned and improved significantly by codoping B 3+ or Na + ions. Energy transfer between Nb \(_{\mathbf {2}}\textit {O}_{\mathbf {6}}^{\boldsymbol {2-}}\) group and Sm 3+ ion was observed and analysed via luminescence properties. The luminous mechanism was explained by energy level scheme and energy transfer process in CaNb 2 O 6 : Sm 3+ phosphor. The strong excitation band peaking at ∼ 407 nm indicated that the CaNb 2 O 6 : Sm 3+ , Na + /B 3+ phosphor has a potential application in white light-emitting diodes based on near-UV LED chip.
研究领域:
材料科学
·
无机化学
·
发光材料
·
固体物理
·
光电子学
✓ 已验证
DOI
高影响因子
MATERIALS RESEARCH BULLETIN
·
2023
·
IF 5.4
Yu Zhang,Kai Li,Xuelian Zhou,Kaixuan Wang,Ze Wang,Sur Lig,Kefu Chao,Fengqi Zhao
Cr 3+ -doped near-infrared phosphors have recently attracted a wide attention. Here, NIR Ca 1- y Sr y Al 12- x Ga x O 19 :0.12Cr 3+ phosphors are obtained by a high-temperature solid-phase method. First, a series of CaAl 7.88 Ga 4 O 19 :0.12Cr 3+ samples is studied and shows that the crystal field strength can be tuned by cation substitutions, until achieving a sharp emission at 692 nm and a broad emission at 780 nm under a 400 nm excitation, and an internal quantum yield of 90.73%. A further substitution by an appropriate amount of Sr 2+ is suggested to be beneficial to increase the rigidity of the crystal structure by Debye temperature calculations. Experimentally, it is observed that Sr 2+ for Ca 2+ substitutions did not affect the luminescence wavelength and resulted in a significant increase of the thermal stability. When 0.7 Sr 2+ substitute Ca 2+ , the thermal stability at 450 K increased by 28% compared to the samples without Sr 2+ .
研究领域:
材料科学
·
无机化学
·
固体物理
·
光学材料
·
功能材料
✓ 已验证
DOI
高影响因子
PARTICLE & PARTICLE SYSTEMS CHARACTERIZATION
·
2023
·Vol. 40
·期 8
·2300032
·
IF 2.7
Hao Jiang,Chenxi Zang,Yixiu Dong,Min Lai,Shuhong Xu,Jingkun Xu
CsPbX 3 (X = Cl, Br, I) nanocrystals (NCs) are competitive materials for a wide range of applications because of their outstanding optoelectronic properties. Ion doping has been demonstrated as one powerful method for improving the optical properties of CsPbX 3 NCs. However, the conventional ion-doping approaches are tedious, and generally performed under an inert atmosphere and high temperature. In this work, a one-step ultrasonic-assisted approach is demonstrated to prepare doped CsPbX 3 NCs. To demonstrate the universality of the ultrasonic-assisted ion-doping approach, three ion-doped perovskite NCs are prepared, which represent three common improvements effects of ion doping on perovskite NCs, namely improved stability, PL emission, and photoluminescence quantum yields (PLQYs) of perovskite NCs. Sr-doped CsPbI 3 NCs showed improved phase stability. Mn-doped CsPbCl 3 NCs showed dual-color emissions at 406 and 580 nm. The PLQYs of the as-prepared Ni-doped CsPbCl 3 NCs are greatly improved, from 10.1% to 71%. Such a simple and versatile ion-doping approach may promote the practical applications of all-inorganic perovskite NCs.
研究领域:
材料科学
·
纳米技术
·
光电子学
·
无机化学
·
半导体材料
✓ 已验证
DOI
高影响因子
ADVANCED POWDER TECHNOLOGY
·
2019
·Vol. 30
·期 9
·1920-1931
·
IF 3.25
Ting Wang,Bing–rui Li,Li–guang Wu,Yu–bing Yin,Bo–qiong Jiang,Ju–qing Lou
La 3+ - or Yb 3+ -doped TiO 2 supported on the surface of reduced graphene oxide were fabricated by adsorbed-layer nanoreactor synthesis (ANS) coupling with a solvothermal treatment to extend photocatalysis application in the advanced treatment of simulated wastewater with high salt concentration. Results showed that La 3+ or Yb 3+ could distribute in the TiO 2 lattice, only in ANS preparation with graphene oxide as the carrier, to replace Ti 4+ during the solvothermal treatment, thus introducing TiO 2 mixed-crystal and heterojunction structures in the catalysts. La 3+ or Yb 3+ caused lattice distortion structures and anionic vacancies in the TiO 2 lattice. The anionic vacancies (oxygen vacancies) might generate Ti 3+ in catalysts, thus enhancing visible-light response, due to impurity levels introduced by La 3+ or Yb 3+ . As the strong adsorption capability of the catalyst for phenol was not interfered by salt ions in the simulated wastewater, the catalysts could efficiently degrade phenol. The highest removal rate of phenol was approximately 90%.
研究领域:
环境科学
·
材料化学
·
光催化
·
水处理
·
纳米材料
·
表面化学
·
环境功能材料
✓ 已验证
DOI
高影响因子
Small
·
2023
·Vol. 19
·期 40
·2303227
·
IF 13.3
YuanZhe Wu,Quan Zong,Chaofeng Liu,Yanling Zhuang,Daiwen Tao,Jiangying Wang,Jingji Zhang,Qilong Zhang,Guozhong Cao
Vanadyl phosphate (VOPO 4 ·2H 2 O) has been regarded as one of the most promising cathode materials for aqueous Zn-ion batteries due to its distinct layered structure. However, VOPO 4 ·2H 2 O has not yet demonstrated the exceptional Zn ion storage performance owing to the structural deterioration during repeated charging/discharging process and poor intrinsic conductivity. In this work, 2D sodium vanadyl phosphate (NaVOPO 4 ·0.83H 2 O, denoted as NaVOP) is designed as a cathode material for Zn-ion batteries, in which sodium ions are preinserted into the interlayer, replacing part of water. Benefiting from the in situ surface oxidization, improved electronic conductivity, and increased hydrophobicity, the NaVOP electrode exhibits a high discharge capacity of 187 mAh g −1 at 0.1 A g −1 after activation, excellent rate capability and enhanced cycling performance with 85% capacity retention after 1500 cycles at 1 A g −1 . The energy storage mechanism of the NaVOP nanoflakes based on the rapid Zn 2+ and H + intercalation pseudocapacitance are investigated via multiple ex situ characterizations.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
纳米材料
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2022
·
IF 4.171
Lin Xiang,Xianju Zhou,Yongjie Wang,Li Li,Sha Jiang,Guotao Xiang,Chuan Jing,Jingfang Li,Lu Yao
Near infrared (NIR) light emitting phosphors have attracted more and more attention with the development of science and technology . Herein, we report a series of environmentally-friendly low-cost Fe 3+ -activated ZnGa 2 O 4 phosphors which exhibit intense broadband NIR light emitting. According to density functional theory (DFT) calculations, ZnGa 2 O 4 host possesses an indirect wide bandgap. The emission of the Fe 3+ -doped phosphors demonstrates a wide band spanning from 650 to 850 nm, with the maximum at 720 nm and a full width at half maxima (FWHM) of 70 nm, showing a large overlap with the absorption of phytochromes (PR and PFR). The luminescence intensity remains at 71% when the temperature is raised to 423 K. The phosphors are fabricated into light emitting diodes (LEDs) which produces strong NIR emission with CIE color coordinates of (0.65, 0.31). All these results suggest that ZnGa 2 O 4 :Fe 3+ is a promising NIR luminescent material , which is expected to be a candidate for indoor plant culture LEDs.
研究领域:
材料科学
·
光电子学
·
农业生物技术
·
固体物理
·
无机化学
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2018
·
IF 2.732
Qinghua Yang,Benxue Jiang,Shuilin Chen,Yiguang Jiang,Pande Zhang,Jun Wang,Shiqing Xu,Long Zhang
Al 2 O 3 : Er 3+ /Yb 3+ transparent ceramics codoped with Zn 2+ ions with intense upconversion and near infrared emission were prepared by conventional solid-state reaction and vacuum and hot isostatic pressing sintering. The effects of Zn 2+ incorporation to the structure, transparent, upconversion and NIR luminescence were discussed in detail. The as prepared Al 2 O 3 ceramics exhibited a total transmittance of ~ 75% in infrared regions (800–3300 nm) and ~ 50% in visible regions (500–800 nm). Under the excitation of a 980 nm laser diode , the as prepared Al 2 O 3 ceramics displayed two tense upconversion emission peaks of a green one centered at 550 nm and a red one centered at 660 nm and a tense near infrared emission peak centered at 1.532 µm, characteristic of Er 3+ emission. Compared with Er 3+ /Yb 3+ doped only, Zn 2+ codoped Al 2 O 3 :Er 3+ /Yb 3+ transparent ceramics showed higher upconversion and near infrared emission of ~ 11 times and ~ 4 times, respectively. The enhancement mechanism due to incorporation of Zn 2+ ions was also discussed in detail.
研究领域:
材料科学
·
光学材料
·
无机非金属材料
·
发光材料
·
陶瓷工程
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2023
·
IF 3.6
Bingkai Gao,Lei Zhang,Runqiu Peng,Panlai Li,Qian Wu,Zhijun Wang
The exploration of performance luminescence near-infrared (NIR) material is crucial for rapidly developing NIR spectroscopic techniques. Herein, the NIR LaMg 0.5 Sn 0.5 O 3 :Cr 3+ phosphor was synthesized by a high temperature solid-state method. And its luminescence performance were improved by [In 3+ -Sc 3+ ] substituting for [Mg 2+ -Sn 4+ ]. The half-peak width can be expanded to 211 nm, the emission intensity can reach the seven times of that un-substitution, and the emission intensity at 423 K was maintained at 60 % of that at room temperature , moreover, the internal quantum efficiency can reach 54.2 %. On this basis, the phosphor converted light emitting diodes ( pc -LEDs) were achieved by combining La(Mg 1-x Sn 1-x In x Sc x ) 0.5 O 3 :Cr 3+ with blue LED, importantly, it can be applied to the biodetection and night vision lighting, which indicate its application value.
研究领域:
材料科学
·
生物医学工程
·
光学材料
·
分子影像
·
转化医学
·
光电子学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）