CARBOHYDRATE POLYMERS
·
2015
·
IF 4.074
Xianglong Li,Huanhuan Chen,Bin Yang
Centrifugal spinning and electrospinning have proved to be effective techniques for fabricating micro-to-nanofibers. However, starches of amylopectin content above 65% cannot be fabricated to fiber by electrospinning. This paper is focus on the centrifugal spinnability of amylopectin rich starches. We investigated the amylopectin content of starches by Dual-wavelength colorimetry, studied the rheological properties of starch dopes to determine entanglement concentration ( c e ) by rotary rheometer. Results indicated that amylopectin rich native corn and potato starches, which with amylopectin content higher than 65%, were suitable for centrifugal spinning to micro-to-nanofibers. Additionally, starch-based fibers were successfully fabricated from the amylose rich corn starch as well. Rheological studies showed that the entanglement concentration ( c e ) of starch solution was crucial for successful centrifugal spinning.
研究领域:
材料科学
·
食品科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2025
·Vol. 16
·期 1
·1-14
·
IF 15.7
Cao Yuanming,Tan Ji,Sun Tingting,Deng Yechuan,Zhang Min,Guan Shiwei,Zhang Xianming,Wei Chao,Huo Panpan,Zhuo Mingpeng,Zhu Hongqin,Qiu Jiajun,Liu Xuanyong
Hydrovoltaic technologies that generate electricity by absorbing or transferring free water without chemical reactions have been explored as potential candidates for renewable energy. Self-powered flexible sensors, including hydrovoltaic fibers, are becoming an important research direction in the field of renewable energy. However, integrating sensing and power generation in functional fibers remains challenging due to the need to regulate water movement to achieve performance differences. Here, we present a gas-liquid two-phase flow spinning method, inspired by spider multimodal spinning, that uses bubble-triggered spinning-liquid deformation to fabricate hollow, solid spindle, and ratchet tooth-shaped fibers. These structures alter water adsorption and transfer behaviors, making them suitable for targeted applications in hydrovoltaic devices for energy and sensing fields. Shaped fibers prepared from alginate-bridged MoS₂ enable a wide range of hydrovoltaic applications. The obtained fiber has a power density of 2.18 mW/cm 3 , stable operation at 2.1 V for 43 hours, and sensitivity of 9.36 mV/RH%/s, leading to the development of smart masks for nasal cycle monitoring, diagnosis, and therapy as potential applications. Spinning materials were extended to materials such as carboxymethyl cellulose, polyvinyl alcohol, etc., inspiring the design of structure-responsive hydroelectric materials and advancing textile electronics.
研究领域:
材料科学
·
能源技术
·
生物医学工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Advanced Science
·
2023
·Vol. 10
·期 36
·2305226
·
IF 15.1
Shaoji Wu,Caihong Gong,Zichao Wang,Sijia Xu,Wen Feng,Zhiming Qiu,Yurong Yan
Hydrogel fibers have attracted substantial interest for application in flexible electronics due to their ionic conductivity, high specific surface area, and ease of constructing multidimensional structures. However, universal continuous spinning methods for hydrogel fibers are yet lacking. Based on the hydrophobic mold induced regional heterogeneous polymerization, a universal self-lubricating spinning (SLS) strategy for the continuous fabrication of hydrogel fibers from monomers is developed. The universality of the SLS strategy is demonstrated by the successful spinning of 10 vinyl monomer-based hydrogel fibers. Benefiting from the universality of the SLS strategy, the SLS strategy can be combined with pre-gel design and post-treatment toughening to prepare highly entangled polyacrylamide (PAM) and ionic crosslinked poly(acrylamide- co -acrylic acid)/Fe 3+ (W-PAMAA/Fe 3+ ) hydrogel fibers, respectively. In particular, the W-PAMAA/Fe 3+ hydrogel fiber exhibited excellent mechanical properties (tensile stress > 4 MPa, tensile strain > 400%) even after 120 days of swelling in the pH of 3–9. Furthermore, owing to the excellent multi-faceted performance and one-dimensionality of W-PAMAA/Fe 3+ hydrogel fibers, flexible sensors with different dimensions and functions can be constructed bottom-up, including the one-dimensional (1D) strain sensor, two-dimensional (2D) direction sensor, three-dimensional (3D) pressure sensor, and underwater communication sensor to present the great potential of hydrogel fibers in flexible electronics.
研究领域:
材料科学
·
柔性电子学
·
高分子化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COMPOSITES COMMUNICATIONS
·
2024
·
IF 6.5
Buguang Zhou,Xiangfei Bu,Jiecong Li,Can Gao,Xiakeer Saitaer,Jiansheng Guo
In recent years, triboelectric nanogenerators (TENGs) have garnered extensive attention in the realm of self-powered sensors due to their capability to harness low-frequency mechanical energy. Among these, textile-based triboelectric nanogenerator stands out as a pivotal platform for wearable sensing. Nevertheless, conventional approaches, such as directly coating triboelectric materials on fabrics, often compromise the inherent properties. In this study, we utilized our self-developed electro-centrifugal spinning equipment to continuously fabricate core-sheath yarns with micro/nano structures, resulting in the development of pocket-shaped fabric-based (PF) TENGs. This innovative design preserves the original softness and breathability of the fabric while delivering substantial electrical output owing to its layered structure and extensive specific surface area. PF–TENGs can accurately detect electrical output signals from various motion states. This electro–centrifugal spinning technology offers new research directions and sensing application prospects for self-powered smart textile development.
研究领域:
材料科学
·
纺织工程
·
纳米技术
·
能源技术
✓ 已验证
产品关联
DOI
高影响因子
RARE METAL MATERIALS AND ENGINEERING
·
2014
·
IF 0.153
Cao Xingxing,Zhang Xuebin,Shao Hao,Feng Yi
Ferroferric oxide nanotubes were prepared by calcining and reducing the composite nanofiber precursors fabricated by electrospinning. Influences of the electrospun parameters (PVA concentration of solution, applied voltage and collector distance) on the preparation of the composite nanofiber precursors were discussed. The structural properties of the obtained nanotubes were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The formation mechanism of the Fe 3 O 4 nanotubes was investigated through the nonequilibrium heat-treatment procedure. Furthermore, the magnetic property of Fe 3 O 4 was measured using a vibrating sample magnetometer. Results reveal that the tubes show a uniform and continuous morphology, whose outer and inner diameters are about 100 nm and 50 nm, respectively. Fe 3 O 4 possesses saturation magnetization ( M s ) of 54.2 A·m 2 /kg, coercivity ( H c ) of 215×79.6 A/m and remanent magnetization ( M r ) of 12.8 A·m 2 /kg, respectively.
研究领域:
材料科学
·
纳米技术
✓ 已验证
DOI
高影响因子
CRYSTENGCOMM
·
2011
·Vol. 13
·期 11
·3905-3909
·
IF 4.006
Dongfei Sun,Xingbin Yan,Jiangtao Chen,Shengxue Yu,Litian Hu,Qunji Xue
In this paper, Zn2TiO4 and TiN nanofibers were prepared by a facile combination of electrospinning followed by thermolysis under different atmospheres. An N,N-dimethyl formamide (DMF)–ethanol solution of poly(vinylpyrrolidone) (PVP), Ti(IV)–isopropoxide (Ti(OC4H9)4) and zinc acetate (ZnAc) was used as the electrospinning precursor and the electrospun nanofibers were calcined at 600 °C in air to generate Zn2TiO4 nanofibers. Subsequently, a conversion from Zn2TiO4 nanofibers to TiN nanofibers was realized through a heat treatment at 1000 °C under an ammonia atmosphere. Investigations using field-emission scanning electron and transmission electron microscopes (FESEM and TEM) revealed the nano-scale fibrous morphology of the obtained products. Energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD) studies confirmed the chemical composition and crystalline structure of the Zn2TiO4 and TiN nanofibers, respectively. The electrochemical properties of the as-prepared TiN nanofibers indicated that the capacitance characteristic of the TiN phase was the electric double-layer capacitance. The value of the specific capacitance gradually decreased with the increase of discharge current density.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2012
·Vol. 108
·期 4
·961-965
·
IF 1.63
Shao Hao,Zhang Xuebin,Chen Fanyan,Liu Shasha,Ji Yi,Zhu Yajun,Feng Yi
In this paper, smooth α -Fe 2 O 3 nanotubes have been successfully synthesized by electrospinning of ferric nitrate–polyvinyl alcohol solution followed by calcination in air. The morphologies and structures of the samples were characterized by transmission electron microscopy, scanning electron microscopy and X-ray diffraction. The catalytic properties were studied by differential thermal analysis and thermogravimetric analysis. The results indicated that the as-prepared α -Fe 2 O 3 nanotubes showed a continuous morphology and an extremely high degree of crystallization. The average inner and outer diameters of the obtained α -Fe 2 O 3 nanotubes were about 60 nm and 100 nm, respectively. The obtained α -Fe 2 O 3 nanotubes were able to lower the temperature of the high-temperature thermal decomposition of ammonium perchlorate, while they had little effect on the crystallographic phase transformation and the low-temperature thermal decomposition.
研究领域:
材料科学
·
催化化学
✓ 已验证
产品关联
DOI
高影响因子
MOLECULES
·
2023
·Vol. 28
·期 8
·3430
·
IF 4.6
Hongtao Guo,Xiaofan Ma,Qiqi Lv,Chunmei Zhang,Gaigai Duan
Compared with traditional metal materials, carbon-based materials have the advantages of low density, high conductivity, good chemical stability, etc., and can be used as reliable alternative materials in various fields. Among them, the carbon fiber conductive network constructed by electrospinning technology has the advantages of high porosity, high specific surface area and rich heterogeneous interface. In order to further improve the conductivity and mechanical properties of pure carbon fiber films, tantalum carbide (TaC) nanoparticles were selected as conductive fillers. The crystallization degree, electrical and mechanical properties of electrospun TaC/C nanofibers at different temperatures were investigated. As the carbonization temperature increases, the crystallization degree and electrical conductivity of the sample also increases, while the growth trend of electrical conductivity is markedly slowed. The best mechanical properties of 12.39 MPa was achieved when the carbonization temperature was 1200 °C. Finally, through comprehensive analysis and comparison, it can be concluded that a carbonization temperature of 1200 °C is the optimum.Keywords:electrospinning;electrical property;pyrolysis temperature;carbonization
研究领域:
材料科学
·
纳米技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF MOLECULAR SCIENCES
·
2023
·Vol. 24
·期 8
·7649
·
IF 5.6
Yanjing Liu,Xiyue Li,Yuezhou Liu,Yaping Huang,Fuming Wang,Yongfang Qian,Ying Wang
Due to their high porosity, large specific surface area, and structural similarity with the extracellular matrix (ECM), electrospun nanofiber membranes are often endowed with the antibacterial properties for biomedical applications. The purpose of this study was to synthesize nano-structured Sc2O3-MgO by doping Sc3+, calcining at 600 °C, and then loading it onto the PCL/PVP substrates with electrospinning technology with the aim of developing new efficient antibacterial nanofiber membranes for tissue engineering. A scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS) were used to study the morphology of all formulations and analyze the types and contents of the elements, and an X-ray diffraction (XRD), thermogravimetric analysis (TGA), and Fourier transform attenuated total reflection infrared spectroscopy (ATR-FTIR) were used for further analysis. The experimental results showed that the PCL/PVP (SMCV-2.0) nanofibers loaded with 2.0 wt% Sc2O3-MgO were smooth and homogeneous with an average diameter of 252.6 nm; the antibacterial test indicated that a low load concentration of 2.0 wt% Sc2O3-MgO in PCL/PVP (SMCV-2.0) showed a 100% antibacterial rate againstEscherichia coli(E. coli).Keywords:nano-textured;Sc2O3-MgO;antibacterial;electrospinning
研究领域:
生物医学工程
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of the American Chemical Society
·
2014
·
IF 11.444
Huilin Hou,Lin Wang,Fengmei Gao,Guodong Wei,Bin Tang,Weiyou Yang,Tom Wu
Recently, preparation of mesoporous fibers has attracted extensive attentions because of their unique and broad applications in photocatalysis, optoelectronics, and biomaterials. However, it remains a great challenge to fabricate thoroughly mesoporous nanofibers with high purity and uniformity. Here, we report a general, simple and cost-effective strategy, namely, foaming-assisted electrospinning, for producing mesoporous nanofibers with high purity and enhanced specific surface areas. As a proof of concept, the as-fabricated mesoporous TiO2 fibers exhibit much higher photocatalytic activity and stability than both the conventional solid counterparts and the commercially available P25. The abundant vapors released from the introduced foaming agents are responsible for the creation of pores with uniform spatial distribution in the spun precursor fibers. The present work represents a critically important step in advancing the electrospinning technique for generating mesoporous fibers in a facile and universal manner.
研究领域:
材料科学
·
纳米技术
·
电化学
·
催化
·
高分子科学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2025
·
IF 8.5
Cen Zhang,Sicheng Li,Di Chen,Wenjing Lu,Chaogeng Xiao
Multicore-shell nanofibers were fabricated by integrating emulsion electrospinning and coaxial electrospinning technologies, in which the multicore section of the nanofibers was prepared by electrospinning of gelatin-stabilized emulsions, and the shell layer was coaxially electrospun from zein solution. Coaxial electrospinning of zein helped form emulsion-based electrospun fibers with bead-in-string, spindle-like, and straight morphologies. The hydrogen bonding between gelatin and zein contributed to the enhanced thermal properties of coaxially electrospun nanofibers. The coating of zein as shell greatly improved fiber surface wettability and mechanical strength. The release behavior of curcumin from the nanofibers was dominated by Fickian diffusion, and the zein shell as a physical barrier favored the prolonged release of curcumin and then the long-lasting antibacterial activity towards Escherichia coli . This work thus gives an insight into the development of the nanofibers by emulsion-coaxial electrospinning as encapsulation matrices for the application in food products.
研究领域:
食品科学
·
材料科学
·
生物医学工程
✓ 已验证
DOI
PubMed
高影响因子
POLYMER
·
2024
·
IF 4.1
Miaomiao Xue,Zhenzhen Quan,Xiaohong Qin,Jianyong Yu,Yuling Li
Numerous experimental data indicate that higher viscosity solutions make it easier to obtain coarser fibers. However, the influences of viscosity on the whipping behavior of the jet and their subsequent impacts on the formation of terminal fiber during electrospinning remain topics of ongoing research. Simulation model and experiment presented in this study aim to solve these problems. The simulation model alters the dimensionless parameter F ve to predict the impacts of different viscosities on the bending behavior of the electrospun jet, while the experiment observes this behavior under different viscosities by regulating the solution concentration. The consistency of the simulation and experimental data implies the accuracy of the conclusions in this paper. Furthermore, the simulation model and experiment have demonstrated that a higher viscosity jet results in a smaller radius of the jet trajectory and lower jet velocity, which in turn leads to the formation of coarser fiber.
研究领域:
材料科学
·
物理学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）