KEY ENGINEERING MATERIALS
·
2020
·
IF 0
Yi Peng Wang,Song Yang,Yun Zhen Jia,Pei Jian Sun,Xue Hui Sun,Hong Bo Wang,Jun Wei Guo,Xiao Bing Zhang,Hui Min Liu,Cong Nie
In this study, carboxymethyl peanut shell (CPS) was prepared, and then peanut shell-based porous material (PPS) was obtained by the complexation reaction of CPS with Cu2+. The carboxymethyl content of CPS increased gradually with the increase of the amounts of monochloroacetic acid and sodium hydroxide, and the Cu2+ loading amount of PPS increased gradually with the increase of carboxymethyl content. The scanning electron microscope results showed that PPS-1, PPS-2, PPS-3 (PPS-1~3) had many nanoscale pores. The nitrogen adsorption-desorption results suggested that PPS-1~3 were all mesoporous materials with an average pore diameter of about 10 nm, while their Brunauer-Emmet-Teller surface area and pore volume of PPS-1 to PPS-3 increased gradually. Compared with the control cigarette, the release of HCN in cigarette mainstream smoke could be effectively reduced with the use of PPS-1~3, the reduction rate of HCN per total particulate matter were 54.9%, 63.1% and 67.0%, respectively.
研究领域:
材料科学
·
环境科学
·
烟草研究
✓ 已验证
DOI
Nanomaterials
·
2022
·Vol. 12
·期 16
·2755
·
IF 5.719
Yue Xu,Huan Liao,Jing Zhang,Haijun Lu,Xinghua He,Yi Zhang,Zhenbin Wu,Hongyu Wang,Minghua Lu
Recovery phosphorus (P) from P-contaminated wastewater is an efficient and environmentally friendly mean to prevent water pollution and alleviate the P shortage crisis. In this study, oyster shell as calcium sources and peanut shells as carbon sources (mass ratio 1:1) were used to prepare a novel Ca-modified biochar (OBC) via co-pyrolysis, and its potential application after P adsorption as a P biofertilizer for soil was also investigated. The results shown that OBC had a remarkable P adsorption capacity from wastewater in a wide range of pH 4–12. The maximum P adsorption capacity of OBC was about 168.2 mg/g with adsorbent dosage 1 g/L, which was about 27.6 times that of the unmodified biochar. The adsorption isotherm and kinetic data were better described by Langmuir isotherm model (R2> 0.986) and the pseudo second-order model (R2> 0.975), respectively. Characterization analysis of OBC before and after P adsorption by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and specific surface area and porosity analyzer (BET) indicated that the remarkable P adsorption capacity of OBC was mainly ascribed to chemical precipitation, electrostatic adsorption, and hydrogen bonding. Pot experiment results showed that OBC after P adsorption could significantly promote the germination and growth ofSpinacia, which manifested that OBC after P adsorption exhibited a good ability to be reused as P fertilizer for soil.Keywords:phosphorous;oyster shell;peanut shell;biochar;P biofertilizer
研究领域:
环境科学
·
农业科学
✓ 已验证
DOI
PubMed
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Yang Liu,Yuanyuan Wang,Jie Ma,Runping Han
ABSTRACT In this study, peanut shell was modified using β-cyclodextrin (β-CD) and citric acid to improve the adsorption capacity for removal of lead ion (Pb 2+ ) and bisphenol S (BPS) from solution in batch mode. Scanning electron microscopy, Fourier-transform infrared spectroscopy, elemental analysis, X-ray fluorescence analysis, specific surface area analysis, thermogravimetric analysis, etc were used to characterize the adsorbent before and after modification. The results showed that the adsorbent was successfully modified. The adsorption results of Pb 2+ and BPS on β-CD-PS indicated that acidic conditions were not conducive to the adsorption of Pb 2+ , the adsorption of BPS basically remained unchanged at pH 2~7, and alkaline conditions were not conducive to the adsorption. The presence of salt had a negative effect on Pb 2+ , but had no effect on the adsorption of BPS. The Langmuir and Koble–Corrigan models could predict the equilibrium adsorption process of Pb 2+ while Temkin and Koble–Corrigan models could describe the equilibrium adsorption process of BPS. The adsorption quantity from experiments is 89.6 mg·g –1 for Pb 2+ and 16.2 mg·g –1 for BPS at 293 K, respectively. The adsorption process of Pb 2+ was consistent with the pseudo-first-order and Elovich models, indicating the presence of ion-exchange in the adsorption process; the adsorption of BPS was consistent with the pseudo-second-order model, indicating that chemisorption was the main rate-controlling step. Thermodynamic studies indicated that the adsorption of Pb 2+ was a spontaneous and endothermic reaction with increasing entropy, while the adsorption of BPS was a spontaneous and exothermic reaction with decreasing entropy. 0.1 mol·L –1 HNO 3 could desorb and regenerate the β-CD-PS adsorbed Pb 2+ for three times, and 75% C 2 H 5 OH had a better desorption and regeneration effect for BPS loaded β-CD-PS. β-CD-PS can effectively remove the lead ion and BPS from mixtures and the study can provide the basis for the effective utilization of peanut shell in environmental remediation.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
Surfaces and Interfaces
·
2022
·
IF 6.137
Xueqiang Liu,Diandi Li,Jiguang Li,Jianle Wang,Shujie Liang,Hong Deng
Heavy metal ion pollution (e.g., Hg, Pb, Cr, Cd) that has a great threat to human health is a global concern, because of their great toxicity (e.g., carcinogenicity and mutagenicity). Therefore, it is necessary to find an economical and efficient technology to remove metal. In recent years, modified biochar plays an important role in the removal of heavy metal. However, most of the biochar modification methods rely on high temperature and long time, which limits their application in practical engineering. In this study, we firstly synthesized HMBC (MnO X -OBC, peanut shells as raw materials) using H 2 O 2 -NaOH method, where the materials only need to be modified for 10 min at ambient temperature to obtain high adsorption performance. The maximum Pb(Ⅱ) and Cd(Ⅱ) adsorption capacities of HMBC were 164.59 mg g − 1 and 36.77 mg g − 1 , respectively, which were 7.2 times and 5.6 times that of the unmodified PBC (peanut shells derived biochar ) , and the main adsorption mechanisms were complexation, ion exchange, cation-π interaction and precipitation. The adsorption process of lead and cadmium by HMBC was more consistent with the Freundlich model and Pseudo-second-order adsorption kinetics . HMBC had high selectivity for lead and cadmium, and the adsorption performance of HMBC was basically not reduced after five cycles. The above experimental results show that the newly prepared HMBC has the potential to treat lead and cadmium industrial wastewater.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2014
·
IF 3.84
Meiling Wang,Guowen Meng,Qing Huang
A prototype of environmentally friendly and low-cost fluorescence sensor, consisting of spinach-extracted chlorophyll- a modified alkali-treated peanut shell (denoted as chlorophyll- a @peanut shell), is achieved and used for trace detection of Hg 2+ in aqueous solutions through fluorescence quenching method. The chlorophyll- a @peanut shell exhibits a linear dynamic detection range from 0 to 19 × 10 −8 M for Hg 2+ with a detection lower limit of 8.5 × 10 −9 M. The feasibility of sensitive and selective detection of Hg 2+ using the chlorophyll- a @peanut shell is also demonstrated in the test of Hg 2+ in synthetic polluted lake waters, showing excellent anti-interference ability to common impurities like silt and alga. Further experiments demonstrate that the improved sensing property of the chlorophyll- a @peanut shell for Hg 2+ than that of chlorophyll- a in solution is ascribed to the selective Hg 2+ adsorption of the alkali-treated peanut shell, which might also be used for the remediation of Hg 2+ in polluted waters. The design concept using non-toxic plants may open a new door to the environmentally friendly and low-cost materials for detection and remediation of environmental pollutants .
研究领域:
环境科学
·
生物化学
✓ 已验证
DOI
高影响因子
Journal of Cleaner Production
·
2020
·
IF 7.246
Jiwen Yang,Guozhao Ji,Yuan Gao,Weng Fu,Muhammad Irfan,Lan Mu,Yulin Zhang,Aimin Li
Adsorptive removal by porous carbon materials has been considered an attractive technique to treat wastewater polluted by antibiotics. To produce porous biochar with high-yield and high-performance for chloramphenicol adsorption, this study prepared biochar from peanut shells using ammonium polyphosphate via pyrolysis . The combined effects of the main process parameters on biochar production were studied to determine the optimum operating conditions by response surface methodology based on Box-Behnken design. Low-dose ammonium polyphosphate has a significant positive effect on the yield, surface functional groups, pore volume, and surface area of biochar. This is caused by the richness of nitrogen and phosphorus in ammonium polyphosphate and its flame retardant property. The high-yield biochar with a surface area of 979 ± 25 m 2 /g was obtained at a mass ratio of ammonium polyphosphate/peanut shell of 0.55, at 650 °C with a retention time of 60 min. The as-prepared biochar exhibited excellent adsorption performance with a monolayer chloramphenicol adsorption capacity of 423.7 mg/g. This was due to the high surface area, micropores formed by nano-sized particles, and richness of N- and P-containing functional groups. The characterization before and after chloramphenicol adsorption indicated micro-pore-filling, Van der Waals force , π-π interaction, and hydrogen-bonding interaction are the main adsorption mechanisms of chloramphenicol adsorption on as-prepared biochar. This study offered new insights on the preparation of biochar from waste biomass for application in wastewater treatment .
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF MOLECULAR SCIENCES
·
2024
·Vol. 25
·期 14
·7583
·
IF 4.9
Shibo Liu,Qishan Zhang,Jiani Liu,Jiarui Li,Wenjia Liu,Yuan Wang,Shaojun Yuan
The doping of porous carbon materials with nitrogen is an effective approach to enhance the electrochemical performance of electrode materials. In this study, nitrogen-doped porous carbon derived from peanut shells was prepared as an electrode for supercapacitors. Melamine, urea, urea phosphate, and ammonium dihydrogen phosphate were employed as different nitrogen dopants. The optimized electrode material PA-1-1 prepared by peanut shells, with ammonium dihydrogen phosphate as a nitrogen dopant, exhibited a N content of 3.11% and a specific surface area of 602.7 m2/g. In 6 M KOH, the PA-1-1 electrode delivered a high specific capacitance of 208.3 F/g at a current density of 1 A/g. Furthermore, the PA-1-1 electrode demonstrated an excellent rate performance with a specific capacitance of 170.0 F/g (retention rate of 81.6%) maintained at 20 A/g. It delivered a capacitance of PA-1-1 with a specific capacitance retention of 98.8% at 20 A/g after 5000 cycles, indicating excellent cycling stability. The PA-1-1//PA-1-1 symmetric supercapacitor exhibited an energy density of 17.7 Wh/kg at a power density of 2467.0 W/kg. This work not only presents attractive N-doped porous carbon materials for supercapacitors but also offers a novel insight into the rational design of biochar carbon derived from waste peelings.
研究领域:
材料科学
·
能源存储
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMOSPHERE
·
2016
·
IF 3.698
Chunlu Li,Nan Chen,Yanan Zhao,Rui Li,Chuanping Feng
In this study, an effective defluoridation adsorbent was developed by depositing polypyrrole (PPy) on granular peanut shell biological carbon (BC) via in situ chemical oxidative polymerization. The variables of defluoridation process (i.e., adsorbent dosage, fluoride solution pH, and anionic interference) were tested. The mechanism was determined by isotherm and kinetic studies, Brunauer-Emmett-Teller (BET) method, scanning electronic microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy and automatic titration. The PPy-grafted BC (PPy/BC) composite performed commendably from pH 2.0 to 10.0, and exhibited high selectivity for fluoride in the presence of several co-existing anions. The experimental data were described well by a Langmuir isotherm curve, and the maximum adsorption capacity was 17.15 mg g −1 . Kinetic studies illustrated the adsorption process was accomplished via surface adsorption as well as by intraparticle diffusion. In addition, mesoporous diffusion was the rate-controlling step in intraparticle diffusion process. BET and SEM analysis revealed the sponge-like polymer adhered to the BC and plugged the pores. XPS, FTIR, and SEM confirmed that fluoride removal was accomplished via the replacement of doped ionizable chloride ions (Cl − ) coupled with positively charged nitrogen (N + ), computation of XPS data enabled the formulation of a three-layer-deep hypothesis for PPy.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
PubMed
高影响因子
POLYMER BULLETIN
·
2015
·Vol. 72
·期 10
·2455-2469
·
IF 1.438
Bai Liangjiu,Wang Dongju,Chen Hou,Li Dongxin,Xu Yuanyuan,Yu Lili,Wang Wenxiang
Abstract Peanut shell (PNS) was used to prepare a novel adsorbent to achieve resource recovery of the agricultural residue. The hydroxyl groups of peanut shell were turned into –C(CH 3 ) 2 –Br pendant groups to initiate polymerization of acrylonitrile. Graft copolymer peanut shell/polyacrylonitrile (PNS- g -PAN) was modified by hydroxylamine hydrochloride to transform the cyano groups into amidoxime (AO) groups. The modified copolymer of AO-PNS- g -PAN was used as adsorbent. The maximum adsorption capacity for Hg(II) was 4.45 mmol g −1 . The adsorption process fitted well the Freundlich isotherm model and followed pseudo-second-order model. The modified copolymer demonstrated its potential as an efficient adsorbent to solve the problem of Hg(II) contamination. Graphical abstract The peanut shell (PNS) macroinitiator was obtained by acylation of hydroxyl groups on the cellulose backbone of the peanut shell and initiated by Cu(0)-mediated RDRP of acrylonitrile. PNS- g -PAN was modified by NH 2 OH·HCl and used to remove heavy metal ions. The maximum adsorption capacity of Hg(II) was 4.45 mmol g −1 .
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
Green Chemistry Letters and Reviews
·
2022
·
IF 6.016
Dongcan Lv,Guangce Jiang,Chengpeng Li,Qianchen Zhu,Zhimin Wang
Modified biomass is a green and renewable sorbent to remove organic pollutants in water. In this study, an efficient bio-based adsorbent was obtained by Fenton-like pretreatment of peanut hull with FeOCl, which can be used to efficiently remove methylene blue from water. The adsorption experiment showed that under the conditions of 25°C, pH 6.0, MB concentration of 100 mg·L−1 and adsorbent dosage of 1.0 g·L−1, the adsorption equilibrium could be achieved within 6 min, with MB removal rate of 85.1% and maximum adsorption capacity of 132 mg·g−1, which was much higher than that of untreated peanut hull (64 mg·g−1). Material characterization showed that Fenton-like pretreatment resulted in the surface morphology change and pore structure formation of peanut hull, and the specific surface area increased significantly, which was an important reason for rapid adsorption. The adsorption mechanism showed that the adsorption of methylene blue followed pseudo second-order models, and conformed to Redlich-Peterson and Langmuir models. According to the thermodynamic analysis results, it is concluded that the adsorption process is endothermic and spontaneous. Adsorption mechanism includes hydrogen bonding, static electricity and van der Waals force.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
WATER AIR AND SOIL POLLUTION
·
2024
·Vol. 235
·期 2
·1-12
·
IF 3.8
Liu Yuze,Liang Yinxiu,Cui Wenjie,Zhai Hongyan,Ji Min
The contamination of chromium (Cr(VI)) in groundwater threatens public health because of the industrial development being historically less supervised. To remove Cr(VI) from groundwater and other surface waters, a new FeCl 3 -modified magnetic biochar (MBPH550) was prepared from a waste peanut hull. The magnetic potential was to facilitate the separation of absorbent from the water phase. The removal efficiency, adsorption kinetics and isotherm models, and adsorption mechanism of Cr(VI) on MBPH550 were investigated. MBPH550 had a large specific surface of 243.23 m 2 /g and saturation magnetization of 5.65 emu/g. MBPH550 achieved a removal efficiency of Cr(VI) up to 92.2% ± 2.0%. Low pH favored the adsorption of Cr(VI). At pH 6.0, the adsorption of Cr(VI) on MBPH550 fits the Elovich kinetic model and Freundlich isothermal adsorption model, with an equilibrium adsorption capacity of 6.64 mg/g. In addition to the direct functional group coordination and precipitation on the surface of MBPH550, Cr(VI) was also reduced to Cr 3+ , Cr(OH) 3 , Cr 2 O 3 , and FeCr 2 O 4 , which were all deposited on the surface of MBPH550. MBPH550 could be a widely applied efficient adsorbent for removing Cr(VI) from wastewater, groundwater, and leachate of Cr-contaminated soil. Graphical abstract
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
BIOMASS & BIOENERGY
·
2024
·
IF 5.8
Yonghui Xu,Yufei Liu,Wei Zhan,Dingle Zhang,Yiyun Liu,Yi Xu,Zhengshun Wu
This study explores the transformation of peanut shells, an abundant agricultural waste, into high-efficiency activated carbon for CO 2 capture using a two-step pyrolysis and K 2 CO 3 activation method. Observations indicated that with an increasing impregnation ratio, the activated carbon demonstrates remarkable improvements in structural properties, achieving specific surface areas and pore volumes of 1150.02 m 2 /g and 0.46 cm 3 /g, respectively. Among the prepared samples, the activated carbon obtained with a peanut shell to K 2 CO 3 impregnation mass ratio of 1:2 exhibits superior CO 2 adsorption capacity at 1 bar, with values of 3.76 mmol/g at 25 °C and 5.70 mmol/g at 0 °C. The CO 2 adsorption isotherms of the activated carbon conform to the Langmuir and Freundlich models. These results demonstrate the potential of this method in addressing environmental concerns, particularly in mitigating CO 2 emissions, and highlight the broader application prospects of biomass-derived activated carbon in environmental management.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）