SOLID STATE IONICS
·
2014
·
IF 2.112
Jing Yang,Zhen Huang,Bingxin Huang,Jing Zhou,Xiaoxiong Xu
NASICON-type structure lithium ion conductors have been considered as promising solid electrolytes due to its very high Li + -ion conductivity and chemical stability. In this paper, NASICON-type structured Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) glass–ceramics are prepared from crystallization of glass powders, which are obtained by a simple melt-quench method. NH 4 H 2 PO 4 , H 3 PO 4 , P 2 O 5 and H 3 PO 4 &Al(PO 3 ) 3 are used as phosphorus sources, respectively. The obtained LAGP glass–ceramics are systematically characterized with X-ray diffraction, field emission scanning electron microscopy , differential scanning calorimetry and AC impedance spectroscopy . The different impurities are formed depending on the phosphorus sources, which further influence the microstructure. As a result, the lithium ion conductivity is significantly affected by the phosphorus sources. The highest conductivity of 5.21 × 10 − 4 S·cm − 1 is obtained when H 3 PO 4 is used as the phosphorus source under optimum conditions.
研究领域:
材料科学
·
固态离子学
·
无机非金属材料
·
能源材料
·
电化学
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2020
·Vol. 46
·期 8
·10917-10924
·
IF 3.83
Li Yang,Qiushi Dai,Lei Liu,Dingsheng Shao,Kaili Luo,Sidra Jamil,Hong Liu,Zhigao Luo,Baobao Chang,Xianyou Wang
Solid electrolytes could address the increasingly urgent safety and energy density concerns of lithium-ion batteries. Among several kinds of solid electrolytes, Ta-doped Li 7 La 3 Zr 2 O 12 (Ta-LLZO) became a research hotspot because of its high Li-ion conductivity and chemical stability against Li-metal and air. However, the preparation of high quality LLZO ceramic electrolyte via conventional air ambient sintering method is still a big challenge due to the serious “Li-loss” and abnormal grain growth phenomenon during the long-time high-temperature sintering process . Herein, a new rapid ultra-high-temperature air ambient sintering method without mother powder (MP) is put forward for the preparation of high quality Ta-LLZO ceramic electrolyte. The rapid sintering strategy can effectively restrain “Li-loss”. Furthermore, it is demonstrated that the none-mother-powder method is superior to traditional mother-powder method. Ta-LLZO ceramics sintered without MP via this rapid sintering method own small grain size, tight grain boundary, dense microstructure and high conductivity. Specifically, the Ta-LLZO ceramic sintered at 1360 °C for 10 min without MP exhibits high conductivity (8.5 × 10 −4 S cm −1 at 25 °C) and high relative density (97%), which equate those made by hot pressing sintering method. Without MP, the sintering process can avoid a lot of material waste and simplify the operation process. Moreover, the rapid sintering process can sharply shorten sintering time and reduce energy consumption. Therefore, this low-cost high-efficient sintering strategy can be effectively used in the large-scale production of high-quality Ta-LLZO ceramic electrolyte.
研究领域:
材料科学
·
固态离子学
·
能源材料
·
电化学
·
无机非金属材料
·
电池技术
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2018
·Vol. 43
·期 7
·3741-3749
·
IF 4.229
Xingcheng Hu,Ravi Muchakayala,Shenhua Song,Jingwei Wang,Jianjun Chen,Manlin Tan
Polymeric ionic liquid-based gel electrolyte films are a new generation of electrolyte materials for flexible energy storage device applications. In this work, Li-ion conducting gel electrolyte films are prepared with the polymeric ionic liquid poly(diallydimethylammonium) bis(trifluoromethane sulfonyl)imide (poly(DADMATFSI)) as the host polymer and the lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt as the dopant . The crystalline nature, thermal stability, ionic conductivity and electrochemical stability window of the polymeric electrolyte films are analyzed by various characterization techniques. It is found that the polymeric electrolyte films exhibit high flexibility and excellent thermal stability. Their room-temperature electrical conductivity increases with increasing LiTFSI concentration and reaches a high value of 1.00 × 10 −3 S cm −1 at 20 wt% LiTFSI. The ionic transference numbers of the polymeric electrolyte films are in the range of 0.98–0.99, indicating that they are perfect ion conductors. Finally, the electrochemical stability window of the 20 wt% LiTFSI-doped polymeric electrolyte film is determined as approximately 6 V, which is a promising value for flexible energy storage device applications.
研究领域:
材料科学
·
电化学
·
高分子化学
·
能源存储
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2023
·
IF 6.2
Yanhua Zhang,Yuhang Mei,Xinglong Gao,Yumei Xiao,Zijun Tang,Xing Xiang,Jiadong Deng
The lithium dendrite problem of Li 7 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) solid electrolyte restricts the practical application and development of all-solid-state lithium batteries (ASSLBs). Herein, a LiPON interlayer with Li + conductive and electron non-conductive dynamic properties is constructed at the Li/LLZTO interface. Results show that the electronic conductivity of solid electrolyte after LiPON modification decreased by nearly three orders of magnitude, indicating that it has good ability to hinder electron conduction . The interlayer enhances the wettability between the Li metal anode and LLZTO, resulting in a decrease of battery resistance from 3400 Ω to 700 Ω. The critical current density of the ASSLBs increase from 0.1 mA cm −2 to 1.2 mA cm −2 at room temperature, and the battery cycle number increase from 31 h to over 1000 h. XPS deep etching results show that the LiPON/LLZTO interface has good electrochemical stability. The Kelvin probe force microscope displays a sharp increase in potential within the LiPON interlayer, indicating its successful hindrance of electron conduction to the solid electrolyte. The effective inhibition of lithium dendrites growth is due to LiPON can promote the Li + transmission from LLZTO solid electrolyte to Li anode, and also hinder the electron conduction to LLZTO to form lithium dendrites.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态电池
·
界面工程
✓ 已验证
DOI
高影响因子
Nano Energy
·
2016
·
IF 11.553
Jingxian Zhang,Ning Zhao,Miao Zhang,Yiqiu Li,Paul K. Chu,Xiangxin Guo,Zengfeng Di,Xi Wang,Hong Li
Solid-state electrolytes with high ionic conductivity , large electrochemical window, good mechanical properties , and easy processability are needed for high-energy solid-state lithium batteries . In this work, composite membranes consisting of lithium garnet (i.e. Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 , LLZTO) particles and Li-salt-free polyethylene oxides (PEOs) are produced as solid-state electrolytes. Li-ion-conducting particles in nano-scale are crucial for the enhancement of conductivity and the membranes containing ~40 nm LLZTO particles exhibit conductivities nearly two orders of magnitude larger than those with the micro-scale ones, which is attributed to the difference in specific surface area related to the percolation effect. Compared to the conventional PEO doped with lithium salt, the insulating PEO in PEO:LLZTO membrane electrolyte is conducive to the suppression of lithium dendrite growth owing to prohibition of current flow. With PEO:LLZTO membrane electrolytes in conductivity of 2.1×10 −4 S cm −1 at 30 °C and 5.6×10 −4 S cm −1 at 60 °C, the solid-state LiFePO 4 /PEO:LLZTO/Li and LiFe 0.15 Mn 0.85 PO 4 /PEO:LLZTO/Li cells deliver energy densities of 345 Wh kg −1 (662 Wh L −1 ) and 405 Wh kg −1 (700 Wh L −1 ) (without the package weight or volume) with good rate capability and cycling performance. This study suggests that the conjunction of nano-scale Li-ion-conducting particles and an insulating polymer provides a promising solution to produce powerful solid-state electrolytes for high-performance solid-state lithium batteries .
研究领域:
材料科学
·
电化学
·
能源存储
·
高分子科学
·
固态电池技术
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）