Materials
·
2020
·Vol. 13
·期 5
·1135
·
IF 3.057
Lei Zha,Heping Li,Ning Wang
TC11 alloy is a promising structural material, and has a wide range of applications in many corrosive and high temperature hydrothermal systems. The passive film has an important influence on its electrochemical behavior. In this study, in-situ electrochemical methods (that is, open circuit potential (OCP), linear polarization (LP) and electrochemical impedance spectroscopy (EIS)) were used to monitor the long period electrochemical behavior of TC11 alloy in 0.01 M Na2SO4solution at 300 °C/10 MPa. The growth kinetics of the passive film was mainly studied. The correlation between the evolution of the electrochemical behavior and the growth of the oxide film was discussed. The results showed that although the OCP gradually stabilized after twenty thousand seconds, henceforth the polarization resistance (Rp) was still increasing due to the thickening of the passive film. An equivalent circuit was proposed to fit the EIS experimental data, leading to determination of film capacitance and film resistance. Besides, the electrochemical data was interpreted in terms of the point defect model (PDM). The EIS results are consistent with theRpresults.Keywords:TC11 alloy;passive film;time;high temperature and pressure;EIS;PDM
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Geoenergy Science and Engineering
·
2024
·
IF 0
Jian Wang,Jinsheng Sun,Xianbin Huang,Kaihe Lv,Xiaodong Dong,Yuan Geng,Shuixiang Xie
There is a lack of viscosity enhancers for high-temperature and high-density solid-free completion solutions in high-temperature and high-pressure oil and gas reservoirs. To address the problem of insufficient temperature resistance of biopolymers and poor performance of conventional viscosifiers in high-temperature and high-density solid-free completion fluids, an anti-temperature viscosifiers for high-density solid free completion fluids was synthesized using N,N-dimethylacrylamide(DMAA), diallyldimethylammonium chloride(DMDAAC) and the amphoteric ion [2-(Methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium Hydroxide(SBMA) as the main monomers. FPOD has salt-responsive properties. With the increase of brine concentration, the degree of stretching of FPOD molecular chain increased and formed a network structure through intermolecular forces, which provided a viscosity increasing effect on the solution. FPOD has good temperature resistance. The apparent viscosity of 1 wt% FPOD in 1.75 g/cm 3 CaBr 2 brine was 37 mPa·s, and after aging at 150 °C, the viscosity was still 32.5 mPa·s. The performance of FPOD before and after aging is better than other viscosifiers. FPOD is simple to prepare and has good viscosity enhancement effect in high density solid-free brines. Moreover, FPOD is well-compatible with other treatment agents for completion fluids, and the HTHP filtration loss of the completion fluid system with 2 wt% FPOD added at 150 °C is only 5 mL. FPOD could solve the problem of insufficient high temperature resistance and viscosity increasing performance of viscosifiers in high density brine completion fluids, and provide a new technical approach to drilling high-temperature and high-pressure oil and gas reservoirs.
研究领域:
石油工程
·
高分子化学
✓ 已验证
产品关联
DOI
Gels
·
2024
·Vol. 10
·期 8
·505
·
IF 5
Shengming Huang,Tengfei Dong,Guancheng Jiang,Jun Yang,Xukun Yang,Quande Wang
Addressing the high friction and torque challenges encountered in drilling processes for high-displacement wells, horizontal wells, and directional wells, we successfully synthesized OAG, a high-temperature and high-salinity drilling fluid lubricant, using materials such as oleic acid and glycerol. OAG was characterized through Fourier-transform infrared (FTIR) spectroscopy and thermogravimetric analysis (TGA). The research findings demonstrate the excellent lubricating performance of OAG under high-temperature and high-salinity conditions. After adding 1.0% OAG to a 4% freshwater-based slurry, the adhesion coefficient of the mud cake decreased to 0.0437, and at a dosage of 1.5%, the lubrication coefficient was 0.032, resulting in a reduction rate of 94.1% in the lubrication coefficient. After heating at 200 °C for 16 h, the reduction rate of the lubrication coefficient reached 93.6%. Even under 35% NaCl conditions, the reduction rate of the lubrication coefficient remained at 80.3%, indicating excellent lubrication retention performance. The lubricant OAG exhibits good compatibility with high-density drilling fluid gel systems, maintaining their rheological properties after heating at 200 °C and reducing filtration loss. The lubrication mechanism analysis indicates that OAG can effectively adsorb onto the surface of N80 steel sheets. The contact angle of the steel sheets increased from 41.9° to 83.3° before and after hot rolling, indicating a significant enhancement in hydrophobicity. This enhancement is primarily attributed to the formation of an extreme-pressure lubricating film through chemical reactions of OAG on the metal surface. Consequently, this film markedly reduces the friction between the drilling tools and the wellbore rocks, thereby enhancing lubrication performance and providing valuable guidance for constructing high-density water-based drilling fluid gel systems.
研究领域:
材料科学
·
石油工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
DIAMOND AND RELATED MATERIALS
·
2012
·
IF 1.913
Liang Li,Aiguo Zhou,Libo Wang,Shangsheng Li,Dongxu Wu,Chengqi Yan
In this paper, titanium aluminum carbide (Ti 3 AlC 2 ) was studied as the binder of polycrystalline cubic boron nitride (PCBN) to overcome the weaknesses of traditional metal binders and ceramic binders. The composites of cubic boron nitride (cBN) and Ti 3 AlC 2 were in situ synthesized from the mixtures of Ti, Al, TiC and cBN powders at high temperature (1050 °C–1250 °C) and under high pressure (4.5 GPa) (HTHP). The Ti 3 AlC 2 proportion in as-prepared composites increased as the processing temperature increased from 1050 °C to 1150 °C. At 1200 °C, part of Ti 3 AlC 2 decomposed to form new TiC. At 1250 °C, cBN transformed to hBN and reacted with other materials. The composites processed at 1200 °C had the optimal mechanical properties , including friction coefficient , hardness and mass loss of worn Si 3 N 4 ball. From the microstructure of as-prepared composites, agglomeration of cBN particles existed; however, the cBN particles, in general, were evenly distributed in the matrix of Ti 3 AlC 2 . The cBN particles strongly bonded with the matrix with a clear interface.
研究领域:
材料科学
·
机械工程
✓ 已验证
产品关联
DOI
高影响因子
FLUID PHASE EQUILIBRIA
·
2023
·
IF 2.6
Shuo Yuan,Yi Liu,Jingwei Cui,Xiong Zheng
Hydrocarbons have wide applications in various industrial processes, and the knowledge of thermophysical properties is the foundation for their utilization. As an important thermophysical property, the thermal conductivity of fluids is vital in the evaluation of energy conversion quality, like heat transfer enhancement , thermodynamic cycle efficiency evaluation, etc. Therefore, obtaining accurate experimental data is of great importance for the utilization of hydrocarbons. Here, the thermal conductivities of liquid n-nonane and n-undecane were investigated using the transient hot-wire method (combined expanded uncertainty is 2.0 %) with a wide temperature and pressure range from 293.15 to 523.15 K and 0.1 to 15.0 MPa. For the convenience of engineering applications, a polynomial as a function of temperature and pressure was proposed to correlate the experimental data, the average absolute deviations between experimental data and fitted data are 0.29 % for n-nonane and 0.35 % for n-undecane, which indicates that the polynomial describes the experimental data well in the measured region. Meanwhile, the available literary data were collected and compared with our results, and good agreement was found between literary data and our results. This work is not only helpful for the industrial applications of hydrocarbons but also helps to understand the internal mechanism of the thermal conductivity of hydrocarbons.
研究领域:
化学工程
·
热物理
✓ 已验证
产品关联
DOI
高影响因子
THERMOCHIMICA ACTA
·
2016
·
IF 1.938
X.K. Gao,X. Wen,H. Zhou,Q. Zhu,J.L. Wang,X.Y. Li
In this work, a novel and simple method was put forward to measure the isobaric specific heat capacity for the kerosene RP-3 with a flow-calorimeter at the conditions of high temperature and high pressure. Based on the energy conservation principle, the formula for heat capacity was derived and its measurement was realized by the convective mixing method between the hot and cold fuel. Taking the precision of the instrument and the error transfer into account, the relative expanded uncertainty of this method was acquired of about ± 6.38% (coverage factor k = 2). Meanwhile, the accuracy and reliability were verified by the standard material of water and n -decane. In the temperature range from (296.2–719.0) K and under pressure range from (2.4–4.0) MPa, the measurement for the kerosene RP-3 was carried out and the experimental observations were compared and agreed well with the published data. At last, an empirical correlation relationship of heat capacity due to the temperature and pressure was presented by using Garg’s model with the measured experimental data.
研究领域:
物理化学
·
能源工程
✓ 已验证
DOI
高影响因子
Minerals
·
2019
·Vol. 9
·期 1
·44
·
IF 2.25
Lidong Dai,Haiying Hu,Wenqing Sun,Heping Li,Changcai Liu,Mengqi Wang
The electrical conductivity of dry sintered olivine aggregates with various contents of magnetite (0, 3, 5, 7, 10, 20, and 100 vol. %) was measured at temperatures of 873–1273 K and a pressure of 2.0 GPa within a frequency range of 0.1–106Hz. The changes of the electrical conductivity of the samples with temperature followed an Arrhenius relation. The electrical conductivity of the sintered olivine aggregates increased as the magnetite-bearing content increased, and the activation enthalpy decreased, accordingly. When the content of interconnected magnetite was higher than the percolation threshold (~5 vol. %), the electrical conductivity of the samples was markedly enhanced. As the pressure increased from 1.0 to 3.0 GPa, the electrical conductivity of the magnetite-free olivine aggregates decreased, whereas the electrical conductivity of the 5 vol. % magnetite-bearing sample increased. Furthermore, the activation energy and activation volume of the 5 vol. % magnetite-bearing sintered olivine aggregates at atmospheric pressure were calculated to be 0.16 ± 0.04 eV and −1.50 ± 0.04 cm3/mole respectively. Due to the high value of percolation threshold (~5 vol. %) in the magnetite impurity sample, our present results suggest that regional high conductivity anomalies in the deep Earth’s interior cannot be explained by the presence of the interconnected magnetite-bearing olivine aggregates.Keywords:electrical conductivity;magnetite;olivine aggregates;percolation threshold;high temperature and high pressure
研究领域:
地球物理学
·
矿物学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2020
·
IF 7.183
Eryue Song,Kaifeng Wei,Haiqian Lian,Jingxian Hua,Hongxu Tao,Tingting Wu,Yichang Pan,Weihong Xing
Metal-organic frameworks (MOFs) used as molecular sieve membranes materials to gas separation has attracted much attention. However, the separation performance was also limited by its intrinsic flexibility of frameworks. Controlling its flexibility is still a big challenge. Herein, the doping of 2-aminobenzimidazole (ambz) into the ZIF-8 framework can obviously improve its original rigidity, which is due to the improved rigidity of the Zn‒N bond. Correspondingly, the high-quality doped ZIF-8 membrane for effective separation of C 3 H 6 /C 3 H 8 mixture were also fabricated. Compared with the permeation results on pure ZIF-8 membranes, the ambz-doped ZIF-8 membrane exhibited two specific transportation performance improvements. The first was that drop extent of C 3 H 6 /C 3 H 8 selectivity on the doped ZIF-8 membrane with the increase in feeding pressure was decreased, and the selectivity was also irreversible as the feeding pressure was released. This phenomenon was attributed to improved rigidity of the framework. The second was that the C 3 H 6 permeance was almost independent on the permeating temperature, which was also totally different with that on the pure ZIF-8 membrane, resulting from the significant change of adsorptive heat and diffusion energy of propylene on the ambz-doped ZIF-8 membrane. Therefore, this ambz-doped ZIF-8 membrane is promising in real world C 3 H 6 /C 3 H 8 separation.
研究领域:
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
Materials Today Communications
·
2025
·
IF 4.5
Changjiang Xiao,Haoyu Zheng,Xiang Li,Lihui Tang
In order to achieve dense SiC ceramics with better properties, SiC w /SiC ceramics without additives were prepared by high-temperature (1450 °C) and high-pressure (5.5 GPa) (HTHP) sintering using SiC whiskers (SiC w ) as a reinforcing phase. The high pressure causes the sintering temperature to be significantly reduced and the sintering time to be greatly shortened. A comprehensive analysis was conducted to elucidate the effect of SiC w content on the structure and mechanical properties of SiC ceramics. As the SiC w content increases, the properties of SiC w /SiC ceramics first improved and then decreased. At 5.0 wt% SiC w , there is the best bonding state between SiC whiskers and SiC matrix, therefore, SiC w /SiC ceramics exhibit the highest relative density of 99.08 %, maximum Vickers hardness of 23.02 GPa and fracture toughness of 9.02 MPa⋅m 1/2 . The main toughening mechanisms are assumed to be the crack deflection, bridging effect and pull-out of whisker.
研究领域:
材料科学
·
陶瓷工程
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2024
·
IF 13.3
Zhi Zhang,Shuai Gao,Haipeng Guo,Yi Wang,Tong Liao,Dongsheng Zhang,Wenqi Zhu,Maohui Bai,Chaochao Fu,Xing Ou,Jixue Shen
The interfacial chemistry influenced by electrolyte components, including lithium salts, solvents, and additives, has attracted significant attention for its critical role in advancing high-performance lithium-ion batteries (LIBs). However, the instability of interfacial interactions between traditional electrolytes and electrodes presents a major obstacle to achieving optimal LIB performance, especially in conditions of high temperature and cut-off voltage. This work introduces an interfacial engineering method utilizing a combination of additives − specifically, fluoroethylene carbonate, ethylene sulfate, and propane sultone (referred to as FDP) − to enhance the conventional carbonate electrolyte for applications in high-voltage and high-temperature LIBs. These additives effectively adjust the interactions between lithium ions and solvents, reducing desolvation energy, thereby decreasing gas evolution, mitigating extensive solvent decomposition, and promoting the formation of a thin, uniform, low-impedance elastic interfacial film on both the anode and cathode. Noteworthy results include a 97.3 % capacity retention at 4.4 V over 250 cycles at 45 °C in a 1.7 Ah-level single crystal LiNi 0.6 Co 0.1 Mn 0.3 O 2 (SC-NCM 613 )||graphite pouch full cell incorporating FDP additives. This interfacial engineering approach facilitated by these multicomponent additives presents a highly promising and practical pathway for achieving long-lasting high-voltage and high-temperature LIBs.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2024
·
IF 5.3
Ling Lin,Yuanhao Luo
Water-based drilling fluids are prone to contamination by high temperatures and high salt, resulting in a deteriorated filtration performance of the drilling fluids, posing a significant threat to the safety of drilling operations. This study utilized N,N-dimethylacrylamide (DMAA), 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS), dimethyldiallylammonium chloride (DMDAAC), N-vinylpyrrolidone (NVP), and nanomaterials (nano-SiO2 and nanolaponite) to prepare a polymer nanocomposite NP-3 as a filtratef reducer for drilling fluids. The thermal stability evaluation of the polymer solution revealed that the thermal degradation temperature order of the different structural units of the polymer is DMAA < AMPS ≈ DMDAAC < NVP, and the temperature resistance of NP-3 in the solution is 220 °C. Evaluation of drilling fluid performance demonstrated that 3.5 wt % NP-3 enabled the drilling fluid to resist contamination from 15 wt % NaCl at 230 °C, with an American Petroleum Institute (API) filtration loss and high-temperature and high-pressure (HTHP) filtration loss after hot rolling of 4.2 and 22.0 mL, respectively. At high temperatures, the degradation of the polymer composite releases nanoparticles, which enhance the density of the filter cake, allowing for adjustable and enhanced control of filtration performance of drilling fluids under high-temperature and high-salty conditions.
研究领域:
石油工程
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Materials
·
2018
·Vol. 11
·期 10
·2020
·
IF 2.467
Hanyi Zhong,Guangcheng Shen,Peng Yang,Zhengsong Qiu,Junbin Jin,Xiaodong Xing
In order to mitigate the loss circulation of oil-based drilling fluids (OBDFs), an oil-absorbent polymer (OAP) composed by methylmethacrylate (MMA), butyl acrylate (BA), and hexadecyl methacrylate (HMA) was synthesized by suspension polymerization and characterized by Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA) and scanning electronic microscopy (SEM). The oil-absorptive capacity of OAP under different solvents was measured as the function of temperature and time. The effect of the OAP on the rheological and filtration properties of OBDFs was initially evaluated, and then the sealing property of OAP particles as lost circulation materials (LCMs) was examined by a high-temperature and high-pressure (HTHP) filtration test, a sand bed filtration test, a permeable plugging test, and a fracture sealing testing. The test results indicated that the addition of OAP had relatively little influence on the rheological properties of OBDF at content lower than 1.5w/v% but increased the fluid viscosity remarkably at content higher than 3w/v%. It could reduce the HTHP filtration and improve the sealing capacity of OBDF significantly. In the sealing treatment, after addition into the OBDF, the OAP particles could absorb oil accompanied with volume enlargement, which led to the increase of the fluid viscosity and slowing down of the fluid loss speed. The swelled and deformable OAP particles could be squeezed into the micro-fractures with self-adoption and seal the loss channel. More important, fluid loss was dramatically reduced when OAP particles were combined with other conventional LCMs by a synergistic effect.Keywords:lost circulation;oil-based drilling fluid;oil absorbent polymer;fracture sealing;combination
研究领域:
石油工程
·
材料科学
✓ 已验证
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）