JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2024
·
IF 9.4
Jiahang Zou,Hanxu Yang,Shilin Wu,Zhengquan Xiao,Zhipeng Jiang,Wangqiang Shen,Yongtao Li
Ether-based electrolytes are known for their high stability with lithium metal anodes (LMAs), but they often exhibit poor high-voltage stability. Structural optimization of ether-based solvent molecules has been proven to effectively broaden the electrochemical window of these electrolytes, yet the optimization rules within cyclic ethers remain unclear. Herein, we investigate the impact of methyl substitution positions on the molecular properties of 1,3-dioxolane (DOL), a commonly used cyclic ether. The results show that the introduction of methyl groups can effectively inhibit the ring-opening polymerization of DOL. Besides, 4-methyl-1,3-dioxolane (4-Me DOL), with larger steric hindrance compared to 2-methyl-1,3-dioxolane (2-Me DOL), exhibits weaker solvation ability, favoring the formation of anion-rich inner solvation sheath layers and anion-derived interfaces. Even at conventional concentrations, 1 M LiFSI in 4-Me DOL (LiFSI/4-Me DOL) electrolyte demonstrates good LMA stability and an expanded electrochemical window up to 4.6 V. The Li-LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM523) cell using LiFSI/4-Me DOL could stably cycle over 300 times. This work reveals a new design principle for solvent molecules.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHINESE JOURNAL OF CHEMICAL ENGINEERING
·
2024
·
IF 3.7
Yue Zhou,Wenjun Li,Hongjun Hu,Zhaohui Wang,Zhaoliang Cui
The membrane aeration biofilm reactor (MABR) represents an innovative approach to wastewater treatment, integrating gas separation membranes with biofilm process and demonstrating effectiveness in treating wastewater rich in ammonia nitrogen. In this system, hollow fiber membranes are essential, serving as a substrate for biofilm attachment while facilitating oxygen transfer to microorganisms through aeration, hydrophobic microporous membranes are utilized in MABR applications. This study focuses on the use of poly-4-methyl-1-pentene (PMP) hollow fiber membranes, which exhibit superior oxygen permeation capabilities compared to traditional hydrophobic microporous membranes. To overcome the challenges posed by the hydrophobic nature and low bubble point of PMP microporous membranes, a hydrophilic modification was conducted using dopamine/poly(ethyleneimine) (DOPA/PEI) co-deposition to enhance microbial adhesion on the membrane surface. The composite membrane modified with DOPA/PEI exhibited an approximately 20% higher NH 4 + -N removal efficiency than the unmodified membrane. These findings suggest that the incorporation of DOPA/PEI significantly improves MABR performance, underscoring its potential for further research and development in membrane technology for MABR.
研究领域:
环境工程
·
生物技术
·
膜科学
✓ 已验证
产品关联
DOI
高影响因子
Environmental Science-Nano
·
2023
·Vol. 10
·期 12
·3317-3328
·
IF 7.3
Baoyu Li,Wengui Duan,Guishan Lin,Yucheng Cui,Rongzhu Wen,Chuwen Liu,Yulu Xie
Natural product-based nanopesticide is an effective and sustainable approach for solving the environmental issues caused by the application of current commercial herbicides. In this study, 21 novel L-carvone-derived 4-methyl-1,2,4-triazole-thioether derivatives 5a–5u were rationally designed by transketolase-based in silicon virtual screening, synthesized, and structurally characterized using FT-IR spectroscopy, 1H/13C NMR spectroscopy, and HRMS technique. Besides, the herbicidal activity of the target compounds against Brassica campestris and Echinochloa crusgalli L. was evaluated, and the bioassay results revealed that compound 5a with the most significant herbicidal and TK-inhibition activities could serve as a potential TK inhibitor and could serve as a leading compound for further study of green herbicides. Subsequently, the molecular skeletons of chitosan and L-carvone were incorporated for developing high-efficiency nanopesticide carriers, and thus samples 7a–7d were synthesized by N-alkylation of chitosan and characterized using various methods. Compared with unmodified chitosan, L-carvone-derived nanochitosan carrier 7b with the micro-morphologies of nubby lumps and porous surfaces exhibited higher dispersibility and similar thermostability. Finally, L-carvone-derived 4-methyl-1,2,4-triazole-thioether/nanochitosan complexes 7b/5a, 7c/5a, and 7d/5a with better 5a-loading capacities and multi-stage sustained releasing performances were constructed, and the herbicidal activities of 7b/5a and 7d/5a against Brassica campestris were evaluated in the petri dish and greenhouse. It was found that 7b/5a and 7d/5a exhibited significant herbicidal activities. Among them, 7b/5a had great potential as a green and eco-friendly nanopesticide for weed control.
研究领域:
植物学
·
农业科学
·
材料科学
✓ 已验证
DOI
高影响因子
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING
·
2023
·Vol. 48
·期 12
·16471-16482
·
IF 2.9
Zainuddin Muhd Izzudin Fikry,Ahmad Abdul Latif,Subramaniam Reasmyraj R.
Carbon dioxide (CO 2 ) separation with membrane technology has become the focus of researchers over the past decades due to its lower energy consumption and cheaper alternative. Mixed matrix membrane (MMM) of poly(4-methyl-1-pentene) (PMP) with nano fumed silica particles was studied to determine the feasibility of using MMM to separate CO 2 from nitrogen (N 2 ) gas. The critical concentration of PMP (7 wt%) was utilized to form the membrane in this study in order to ensure the polymer chain entanglement occurs to form a dense structure. Agglomeration of particle can be observed on the surface with scanning electron microscopy (SEM) imaging with 10 and 15 wt% of nano fumed silica loading in PMP matrix. This observation is further confirmed with energy-dispersive X-ray (EDX) mapping across the cross-sectional area which shows clustered nano fumed silica particle with loading of 10 and 15 wt%. With 7.5 wt% filler loading and at 1 bar, the MMM seems to give the best gas permeance performance with CO 2 permeance of 4.62 GPU (100.54 Barrer) and N 2 permeance of 0.20 GPU (4.31 Barrer) which makes the highest ideal selectivity to be about 23, which was the highest ideal selectivity achieved in this study. Meanwhile, when the pressure was increased from 1 to 7 bar, the CO 2 permeability increased almost linearly followed by a steady decline in CO 2 /N 2 ideal selectivity.
研究领域:
膜技术
·
气体分离
·
高分子科学
·
纳米复合材料
·
环境工程
✓ 已验证
DOI
高影响因子
LANGMUIR
·
2023
·
IF 3.9
Donghai Sheng,Lin Zhang,Hao Jia,Baoming Guo,Xiangjun Zhang,Yuan Li
As the key component of extracorporeal membrane oxygenation (ECMO), artificial lung membranes have low gas permeability and plasma leakage problems, and the contact between membrane materials and blood can cause coagulation, leading to the blockage of medical equipment and seriously threatening the safety of human life. In our work, poly(4-methyl-1-pentene) hollow fiber membranes (PMP HFMs) were prepared by the thermally induced phase separation (TIPS) method, the redox method was adopted for the surface hydroxylation of PMP HFMs, and then, heparin (Hep) and 2-(methacryloyloxy)ethyl(2-(trimethylammonio)ethyl) phosphate (MPC) were grafted to the surface of PMP HFMs to prepare anticoagulant coatings. The gas permeability and hemo-compatibility of the coatings were investigated by various characterization methods, such as gas flow meter, scanning electron microscope, extracorporeal circulation experiment, etc. The results show that PMP HFMs possess a bicontinuous pore structure with a dense surface layer, which could maintain good gas permeability with an oxygen permeance of 0.8 mL/bar·cm2·min and stable gas selectivity. Furthermore, the whole blood circulation of rabbit indicated that a composite surface of bioactive Hep and biopassive MPC might be used as artificial lung membranes without the formation of thrombosis within 21 days.
研究领域:
生物医学工程
·
材料科学
✓ 已验证
DOI
高影响因子
LANGMUIR
·
2023
·
IF 3.9
Donghai Sheng,Lin Zhang,Hongfei Shang,Baoming Guo,Yuan Li
The contact between the blood and the surface of medical materials causes a series of rejection reactions. In this process, the plasma protein is adsorbed to the surface of materials within seconds and binds to glycoprotein receptors on platelets, causing platelet activation, coagulation cascade, and complement activation to form thrombus, which greatly limits the application of medical materials. In our work, the surface of poly(4-methyl-1-pentene) hollow fiber membranes (PMP HFMs) was coated with a diamond-like carbon (DLC) film by the ion plating method. The blood compatibility of the DLC coating was evaluated by protein adsorption, platelet adhesion, clotting time, red blood cell (RBCs) hemolysis, dynamic coagulation, and extracorporeal blood circulation tests. Compared with the unmodified PMP membrane, the DLC film could effectively reduce protein adsorption and platelet adhesion and prolong the coagulation time. The DLC coating showed BSA adsorption of as low as 0.53 μg/cm2 as well as a long activated partial thromboplastin time (APTT) value of 71.84 s. Furthermore, the PMP membrane modified with the DLC coating was used for extracorporeal blood circulation without thrombosis forming within 28 days. The DLC coating is one of the most promising medical coatings as an artificial lung membrane in extracorporeal membrane oxygenation (ECMO) equipment.
研究领域:
生物医学工程
·
材料科学
·
血液学
✓ 已验证
DOI
高影响因子
Molecular Catalysis
·
2023
·
IF 4.6
Yuanning Yue,Ying Liao,Jiarong Lu,Yue Pan,Meiyu Zhang,Guiyue Chen,Xin Zhou,Xinyu Kuang,Hui Zhao,Xiaobo Chen,Xiang Feng,Hao Yan,Yibin Liu,Chaohe Yang
Recognizing and modifying the acid property-dependent catalytic characteristics of catalysts are of great importance for Prins condensation reaction. Herein, a series of metal-doped M-NH 4 -PW catalysts ( M =Pt, Fe, Ir, Ru) are successfully synthesized for Prins condensation reaction of formaldehyde and propylene to produce 4-methyl-1,3-dioxane. Our findings demonstrate that the catalytic performance of M-NH 4 -PW catalysts is influenced by the chemical nature of metal site properties with different electron transfer abilities. Specifically, the new Lewis acid decorated by Pt metal on 4-H site is more favorable for the selective adsorption of formaldehyde and activation of its C O bond. Additionally, the synergistic effect between Pt metal sites and nearby O in [PW 12 O 40 ] 3− promotes the formation of C C bonds between protonated formaldehyde and propylene. Consequently, the Pt-NH 4 -PW catalyst exhibits high conversion (> 80 %) and simultaneous selectivity towards 4-methyl-1,3-dioxane selectivity (65 %). This strategy may provide valuable insights for developing efficient multifunctional catalysts for Prins condensation reactions.
研究领域:
催化
·
化学工程
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2025
·
IF 9
Yuhang Guo,Guangzhaoyao Yang,Shiyao Yu,Jing Huang,Fusheng Pan,Runnan Zhang,Haojun Fan,Zhongyi Jiang
Poly (4-methyl-1-pentene) (PMP) is widely used between blood and gas in extracorporeal membrane oxygenation (ECMO). However, it is more suitable to miniaturize the oxygenator from an economic and biosafety standpoint, that necessitates the PMP oxygenation membrane with enhanced gas permeance and hemocompatibility. This study introduced fluorinated covalent organic framework (FCOF) nanofiber into PMP matrix to construct PMP-FCOF hybrid flat sheet membranes and hollow fiber membranes (HFMs) via thermally induced phase separation (TIPS). FCOF exhibits structural and chemical similarity with PMP, ensuring the good compatibility with PMP matrix. The abundant C–F bonds rendered membrane low-surface-energy of ∼30.2 mN m −1 for PMP–FCOF–3 flat sheet membrane, exhibiting better hemocompatibility compared with that of ∼34.4 mN m −1 for the PMP membrane. The fabricated PMP–FCOF–3 HFMs for blood gas exchange with O 2 exchange rate of ∼309.8 mL min −1 m −2 , which was 77.3 % higher than the commercial PMP HFM, and comparable CO 2 exchange rate of ∼251.7 mL min −1 m −2 with commercial PMP HFM. The blood-gas exchange and hemocompatibility were synergistically enhanced by a simple hybrid strategy, exhibiting great application potentials.
研究领域:
生物医学工程
·
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2022
·
IF 10.53
Yiwen Wang,Yang Liu,Qiu Han,Haibo Lin,Fu Liu
Extracorporeal membrane oxygenation is a technique that provides short-term supports to the heart and lungs. It removes CO 2 from the blood and provides enough oxygen, which is a huge help in the fight against COVID-19. As the key component, the artificial lung membranes have evolved in three generations including silicon, polypropylene and poly (4-methyl-1-pentene). Herein, we for the first time design and fabricate a novel poly (4-methyl-1-pentene)/polypropylene (PMP/PP) thin film composite (TFC) membrane with the anticoagulant coating composed of poly (sodium 4-styrenesulfonate) and cross-linked poly (vinyl alcohol). Poly (sodium 4-styrenesulfonate) provides sulfonic acid groups to inhibit the coagulant factors (FVIII and FXII), and cross-linked poly (vinyl alcohol) increase the stability of the anticoagulant coating and further improve the hydrophilicity via abundant hydroxyl groups to depress the protein adsorption. Long-term anticoagulant property was demonstrated by whole human blood for 28 days. Blood compatibility was evaluated by hemolysis rate, anticoagulation activity (APTT, TT and PT), complement activation, platelet activation and contact activation. Pure CO 2 , O 2 and N 2 permeation rates were determined to evaluate the mass transfer properties of PMP/PP TFC membranes. Gas permeation results revealed that gas permeation flux increased in the TFC membranes because of the decrease of crystallinity. Overall, the so prepared PMP/PP membrane shows good CO 2 /O 2 selectivity and blood compatibility as novel TFC artificial lung membrane.
研究领域:
生物医学工程
·
材料科学
·
医疗器械
·
血液相容性
·
气体分离膜
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）