COLLOIDS AND SURFACES B-BIOINTERFACES
·
2019
·
IF 3.973
Lingyan Yang,Liliang Chen,Yi-Chun Chen,Lei Kang,Jiantao Yu,Yuhang Wang,Chengjia Lu,Tsutomu Mashimo,Akira Yoshiasa,Chia-Hua Lin
Immiscible bimetallic Ag–Cu system has been synthesized by the pulsed plasma in liquid method with a graph of one pulse duration. Herein, by combining X-ray power diffraction, K-edge X-ray absorption near edge structure and high-resolution transmission electron microscopy, our results indicate that homogeneously alloyed Ag–Cu nanoparticles (Ag–Cu NAs) have the average diameter about 2.1 nm, composed by 48.5 at% Ag and 51.5 at% Cu with chemical analysis and the estimated lattice parameter was 3.873 Å. The antibacterial property of Ag–Cu NAs was detected against E. coli and S. aureus strains according to the colony formed abilities of bacteria on agar plates covered with the nanoparticles. With very short incubation period, Ag–Cu NAs completely inhibited the E. coli and S. aureus growth at an ultralow concentration. The mechanism of antibacterial property of Ag–Cu NAs was performed by the inductively coupled plasma-atomic emission spectrometry and the plane wave pseudopotential method implemented in the CASTEP package based on the density functional theory. The Ag + dissolution is correlated with antibacterial activity for Ag–Cu NAs-assisted antibacterial treatment. These findings obtained revealed that our Ag–Cu NAs could be served as a containing material of numerous bacteria-free products in order to avoid their bacterial contamination.
研究领域:
材料科学
·
微生物学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Materials Research and Technology-JMR&T
·
2020
·
IF 5.289
Wei Wang,Yaping Liu,Gang Wang,Caiwang Tan,Wei Cao
In this study, the carbon fiber reinforced ZrB 2 -SiC composite ceramic was joined to Ti6Al4V alloy with Ag-Cu eutectic alloy filler at varied holding time and a fixed temperature of 800℃. Interface microstructure and shear strength of brazing joints were studied. The brazed ZSC f ceramics/AgCu/TC4 alloy is endowed with good metallurgical bondings. A typical interfacial structure of joints brazed for 10 min was found as ZSC f /TiC/Ti 5 Si 3 /Ag(s,s)/Cu(s,s) + TiC/TiCu/Ti 2 Cu/(TiC + TiCu)/TC4 alloy. Increase of holding time did not vary the precipitated phase of the joints but decreased thickness of the Ag(s, s) and Cu(s, s) reaction layer and gradually thickened the Ti-Cu reaction layer near the TC4 side. The formation process of reaction products was discussed in detail. The holding time substantially influenced shear strength of the joints. A maximum shear strength of 39 MPa was reached at a brazing time of 20 min.
研究领域:
材料科学
·
焊接工程
✓ 已验证
产品关联
DOI
高影响因子
Chemical Engineering and Processing-Process Intensification
·
2024
·
IF 3.8
Xiaocui Zhang,Xiaoxin Wang,Jun Gao,Jiangcheng Li,Xiangfeng Liang,Qinghui Shou
The global need for bromide ions (Br - ) has driven the research focus to extract them from various liquid ores. Highly efficient and selective adsorbent is still lacking. MOF with large surface area and structural stability are promising candidate for Br - extraction. In this work, we prepared Cu-MOF-74 nanocrystals. Abundant hydroxyl groups on them spontaneously reduced Ag + to Ag 0 nanoparticles, resulting in the fabrication of Ag 0 doped Cu-MOF-74. The crystalline structure retains after the doping of Ag 0 when the mass ratio of silver nitrate to MOF is <0.5. The crystals are distorted or even damaged when the ratio is higher than 1.0 according to XRD and DFT calculation. The adsorption capacity of Ag 3 -Cu-MOF-74 is 232.92 mg g -1 , surpassing the capacities of most previously documented adsorbents. The desorption of Br - and thereafter the recovery of adsorbent could be realized through light driven decomposition of AgBr. This MOF adsorbent shows promising application potential in Br - recovery from various liquid ores.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2024
·
IF 5.8
Shihao Xiong,Tao Peng,Liangliang Huang,Rui wang,Beibei He,Jun Jin,Huanwen Wang,Yansheng Gong
Semiconductor photocatalytic nitrogen reduction reaction (PNRR) stands as a promising clean technique for ammonia synthesis, yet it confronts numerous challenges. In this study, Ag nanoparticle-modified Cu-doped Bi 2 WO 6 (ACB) porous composite materials with varying mass percentages were successfully synthesized using a solvothermal reduction approach. The incorporation of transition metal Cu effectively modulates the energy band position of Bi 2 WO 6 . Furthermore, the introduction of Ag nanoparticles significantly suppresses the recombination of photogenerated carriers. Without adding sacrificial agent, the photocatalytic nitrogen fixation yield of ACB reaches an impressive 184.93 μmol·g −1 ·h −1 , which is 5.44 times higher than that of pristine Bi 2 WO 6 . A comprehensive analysis of the experimental results reveals that the combined effect of Cu doping and Ag nanoparticle loading endows ACB with an increased exposure of active sites, thereby significantly enhancing its photocatalytic nitrogen fixation performance. This research offers a promising approach for the design of metal nanoparticle-supported catalysts for PNRR, holding significant implications for the advancement of other material systems.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
Materials Research Express
·
2016
·Vol. 3
·期 6
·065018
·
IF 0.968
Pinhua Zhang,Guangliang Cui,Chuanhai Xiao,Mingzhe Zhang,Li Chen,Changmin Shi
We fabricated an Ag decorated Cu (Ag@Cu) nano/microstructure ordered array by facile template-free 2D electrodeposition combined with a galvanic reduction method for SERS applications. The Cu nano/microstructure ordered arrays were first synthesized by a 2D electrodeposition method, then Ag nanocubes were decorated on the arrays by galvanic reduction without any capping agent. The pollution-free surface and edge-to-face heterostructure of Ag nanocubes and Cu nano/microstructure arrays provide the powerful field-enhancements for SERS performance. The results verified that the Ag@Cu nano/microstructure ordered arrays have excellent activity for 4-Mercaptopyridine, and the sensitivity limit is as low as 10−8 M. Therefore, this facile route provides a useful platform for the fabrication of a SERS substrate based on nano/microstructure ordered arrays.
研究领域:
材料科学
·
纳米技术
·
光谱学
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·
IF 5.1
Chaochen Chen,Fang Lei,Ying Shi,Jianjun Xie,Lei Zhang,Lingcong Fan
The surface metallization of Si 3 N 4 ceramics with the Ag–Cu conductive paste containing CuO was systematically investigated. The interfacial reactions between CuO and Si 3 N 4 promoted the surface metallization of the ceramic substrate in an argon atmosphere. The effects of Ag and Cu relative contents on the evolution of the thick film surface morphology were studied. The electrical properties and tensile strength of composite ceramic substrates were enhanced through the generation of Ag–Cu eutectic solution within the thick film layer. The effect of brazing time on the properties of Ag–Cu/Si 3 N 4 composite ceramic substrates was investigated. Mechanical testing and scanning electron microscopy (SEM) were used to analyze the interface tensile strength of the Ag–Cu/Si 3 N 4 composite substrates and the morphology of the Ag–Cu film, and the bonding mechanism of the composite ceramic substrate was studied. When the sample was brazed at 800 °C for 20 min, the maximum tensile strength of 23.6 MPa between the Ag–Cu film and ceramic substrate was obtained, the lowest resistivity of 6.22 μΩ•cm was obtained. The bonding interface between thick film layer and the ceramic substrate formed the Ag–Cu mechanical structure was benefit for improving the comprehensive performance of the Cu/Si 3 N 4 composite ceramic substrate.
研究领域:
材料科学
·
陶瓷工程
✓ 已验证
产品关联
DOI
高影响因子
FOOD CHEMISTRY
·
2025
·
IF 9.8
Xishun Peng,Yiheng Yuan,Anjiang Lu,Cunwei Wang,Caizhen Zu,Haili Zhang,Zhongchen Bai
Glyphosate (Gly) residues in agricultural products have a serious health risk, so it is urgent to seek a sensitive and convenient method for recognizing Gly residues in food. In this study, we proposed an electrochemical surface-enhanced Raman spectroscopy (EC-SERS) sensor of polyaniline/reduced graphene oxide/Ag/Cu (PANI/RGO/Ag/Cu) film to detect Gly residues. The EC-SERS sensor of PANI/RGO/Ag/Cu film had a large specific surface area, which could increase the binding sites of cu 2+ /Gly clathrates for boosting specifically its SERS signal. Moreover, Ag/Cu nanoparticles on the surface of film could effectively increase the differential pulse voltammetry signal and SERS signal of Gly molecules. The limit of detection of EC-SERS sensor to Gly could reach 1.9 nM. In addition, the EC-SERS sensor we prepared could also sensitively identify Gly residues on fresh fruit peels. The PANI/RGO/Ag/Cu film we proposed in this paper has great potential for selective and accuracy detecting Gly residues in agricultural products.
研究领域:
食品科学
·
分析化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Materials & Interfaces
·
2024
·
IF 8.3
Hu Li,Yingying Peng,Weixiang Zhou,Jun Guo,Chao Gao,Yapeng He,Mingxi Pan,Congqing Yang,Hui Huang
In the development of back electrodes for perovskite solar cells (PSCs), the major challenges are stability and cost. To address this, we present an innovative approach: Simultaneous evaporation of two independently controlled sources of metal materials was performed to achieve a uniform distribution of the alloy electrodes. In this study, Ag–Cu alloys (the molar ratio of Ag/Cu is 7/3) with a high-index crystal face (111) and a work function matching perovskite were prepared using a codeposition technique. These properties mitigate nonradiative carrier recombination at the interface and reduce the energy barrier for carrier migration. Consequently, compared to Ag based PSCs (22.77%), the implementation of Ag–Cu alloy (Ag/Cu is 7/3)-based PSCs resulted in a power conversion efficiency of 23.72%. In a 1500 h tracking test in ambient air, the Ag–Cu alloy (Ag/Cu is 7/3)-based PSCs maintained their initial efficiency of 86%. This can be attributed to almost no migration of elements from the Ag–Cu alloy electrode to the perovskite layer. Our work presents a vital strategy for improving the stability of PSCs and reducing the costs associated with the back electrode in PSCs.
研究领域:
材料科学
·
能源技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Science China-Technological Sciences
·
2015
·Vol. 58
·期 5
·881-888
·
IF 1.192
Yang AiLing,Li ShunPin,Wang YuJin,Wang LeLe,Bao XiChang,Yang RenQiang
Ag@Cu 2 O core-shell metal-semiconductor nanoparticles (NPs) were prepared by using solution phase strategy. It was found that Ag@Cu 2 O core-shell NPs were easily converted to Ag@Cu bimetallic core-shell NPs with the help of surfactant PVP and excessive reducer ascorbic acid in air at room temperature, which is a unique phenomenon. Varying volumes of Ag colloidal solutions were added into the reaction mixtures containing fixed initial concentrations of Cu 2+ and PVP, Ag@Cu 2 O and Ag@Cu core-shell NPs with fixed core size but varying outer shell thicknesses could be obtained. The composites, structures, morphologies and extinction properties of Ag@Cu 2 O and Ag@Cu core-shell NPs were systematically characterized by XRD, TEM and extinction spectra. Both of these NPs show wide tunable optical properties. The extinction peaks could be shifted from 421 nm to 700 nm. FTIR results reveal that Cu + ions on the surface of Cu 2 O nanocrystalline coordinate with N and O atoms in PVP and further are reduced to metallic Cu by excessive ascorbic acid and then form a nucleation site on the surface of Cu 2 O nanocrystalline. PVP binds onto a different site to proceed with the reduction until all the Cu sources in Cu 2 O NPs are completely assumed. And the shell of Cu 2 O is converted to Cu shell. The synthesis approach in this paper is simple and also a promising reference for synthesizing other core-shell NPs. Ag@Cu 2 O NPs can be easily converted to Ag@Cu NPs in air at room temperature, which is promising to be used in electronic devices.
研究领域:
纳米材料化学
·
无机功能材料
·
胶体与界面化学
·
光谱学
·
半导体物理
✓ 已验证
DOI
高影响因子
IEEE SENSORS JOURNAL
·
2025
·
IF 4.5
Zelong Li,Xuemei Lin,Zengshan Yu,Guochao Shi,Wenying Zhou,Jiahao Cui,Shan Guo,Mingli Wang
Accurate and sensitive detection of bilirubin, cholic acid, and Alanine aminotransferase (ALT) is essential for the early detection of hepatobiliary diseases in healthcare and the medical field. Integrating surface-enhanced Raman scattering (SERS) with deep learning algorithm has shown great application prospect in the early identification of markers of hepatobiliary diseases. Here, an regular Ag decorated Cu-Ag nanoisland-liked SERS biosensor (Ag@5/Ag-Cu@20/PSS) was constructed by using pattered sappire substrate as a template. An additional 5 mins of Ag nanofilm significantly improved the SERS signal intensity and homogeneity, and the sensitivity was enhanced by two orders of magnitude up to 10-10 M for 4-aminothiophenol (4-ATP). Importantly, deep learning algorithms included temporal convolutional networks (TCN), convolutional neural networks (CNN), recurrent neural network (RNN) and Transformer were used to deeply mine SERS spectral data of bilirubin, cholic acid and ALT, extract effective features, and establish an accurate classification and prediction model. Results indicating that the developed SERS biosensor combined with Transformer model demonstrated excellent accuracy (ACC) of 0.9816±0.0090 in qualitatively and quantitatively analyzing of bilirubin, cholic acid, and ALT. The successful application of the SERS biosensor will help improve the accuracy of early identification of bilirubin, cholic acid, and ALT disease markers and promote the early intervention and treatment of hepatobiliary diseases.
研究领域:
生物医学工程
·
分析化学
·
人工智能
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2024
·
IF 8.1
Peilin Jia,Dongzhi Zhang,Xingyan Shao,Jieshuo Zhai,Jishun Guo,Zijian Wang,Xinyi Ji
Hydrogen (H 2 ), as a clean energy source, exhibits significant promise in the realm of new energy vehicles. Utilizing hydrogen sensors with rapid response and high selectivity is crucial for monitoring vehicles and preventing hydrogen leakage incidents. In this study, In 2 O 3 nanomaterials were synthesized via a hydrothermal approach and effectively modified with Ag/Cu bimetallic nanoparticles to fabricate high-performance hydrogen sensors. The optimal work temperature for the Ag/Cu–In 2 O 3 sensor is determined to be 300 °C. At this temperature, the sensor exhibited a response of 9.66–100 ppm H 2 , which is four times higher than the pristine In 2 O 3 sensor. Excellent H 2 selectivity and outstanding long-term stability were exhibited by the sensor in typical interference gas environments encountered in new energy vehicles. The significant enhancement in sensor performance is attributed to the electronic and chemical sensitization effects of Ag/Cu bimetals and the synergistic effects of bimetallic modification. Additionally, computational studies based on density functional theory (DFT) further elucidated the reasons for the improved H 2 gas sensing performance of Ag/Cu–In 2 O 3 nanocomposites. The Ag/Cu–In 2 O 3 nanocomposites show great potential for hydrogen detection applications in the sensor field.
研究领域:
材料科学
·
化学工程
·
能源技术
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2022
·
IF 9.965
Jie Chen,Wenhao Xu,Xingjin Li,Libo Sun,Zihan Zhong,Zitao Zhang,Yun Tang
The optical properties of cost-effective Ag-Cu bimetallic nanocrystals, with synergistically enhanced catalytic and biological activities, are limited within ultraviolet–visible region due to lack of morphology control. In order to overcome this constraint, two-dimensional (2D) Ag-Cu bimetallic heterostructures were designed and synthesized by a seed-mediated colloidal growth method. The conformal Cu domain was epitaxially deposited on Ag nanoplates with different spatial configuration under retention of their 2D shape. Both of the 2D Ag-Cu core@shell and Janus structures display tunable localized surface plasmon resonance from visible to near infrared regions. The results of catalytic reduction of 4-nitrophenol show that the 2D Ag-Cu core@shell structure has better synergistic catalytic performance than Janus structure and Ag plates. In addition to surface-related synergistically enhanced bactericidal performance, their antibacterial effect can also be significantly enhanced by near infrared light irradiation. These results indicate that 2D Ag-Cu heterostructures can benefit from both synergistically improved surface activity and great optical responsive characteristics.
研究领域:
材料科学
·
纳米生物学
·
光学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）