ELECTROCHIMICA ACTA
·
2017
·
IF 4.798
Wei Fang,Naiqing Zhang,Lishuang Fan,Kening Sun
Polypyrrole-coated Bi 2 O 3 @CMK-3 nanocomposite is prepared by nanocasting technique and chemical polymerization method. Bi 2 O 3 nanoparticles are dispersed into CMK-3 matrix, and polypyrrole is coated onto the surface of Bi 2 O 3 @CMK-3. Polypyrrole-coated Bi 2 O 3 @CMK-3 nanocomposite as an anode material for lithium-ion batteries has an outstanding power capability (321 mAh g −1 at a current rate of 6 A g −1 ) and a significantly improved cycling ability (380 mAh g −1 after 1000 cycles at a current rate of 5 A g −1 ). The greatly enhanced electrochemical performance of polypyrrole-coated Bi 2 O 3 @CMK-3 nanocomposite is associated with the synergistic effect of highly conductive CMK-3, polypyrrole layer and Bi 2 O 3 nanoparticles. Such a configuration inhibits the aggregation of Bi 2 O 3 nanoparticles and preserves the structure integrity of electrode material, in addition to highly improving the electrical conductivity and maintaining the stable structure of solid electrolyte interface film.
研究领域:
材料科学
·
能源存储
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2015
·
IF 2.037
Qiaobei Dong,Yan Sun,Wei Su,Jia Liu
The use of hydrate formation in porous media is an effective method for gas storage and separation. The equilibrium isotherms of CH4 and N2 in CMK-3, a mesoporous carbon material, were measured under different tetrahydrofuran (THF) concentrations and temperatures. The higher is the temperature required, the greater is the formation pressure needed, but the presence of THF significantly reduces the hydrate formation pressure. When THF exists, both CH4 and N2 form structure II (sII) hydrate; however, the amount of hydrate generation is lower than the theoretical value. As the operating pressure increases, some of the sII CH4 hydrate may transform into structure I (sI) and the amount of hydrate generation increases. The desorption isotherms showed that the gas hydrate decomposed completely when the operating pressure was below the hydrate decomposition pressure. In addition, it is feasible to separate gas mixtures via hydrate formation using the different gas hydrate formation pressures.
研究领域:
化学工程
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Nanomaterials
·
2019
·Vol. 9
·期 3
·364
·
IF 4.034
Yanfeng Chen,Cuiyin Liu,Yue Situ,Jian Liu,Hong Huang
In this work, the CMK-3 is successfully prepared with SBA-15 as the template and first annealed to 2000 °C to improve thermal conductivity. The annealed CMK-3 has a thermal conductivity of 6.981 W m−1K−1higher than un-annealed CMK-3. The annealed CMK-3 is used to encapsulate the RT44HC, and RT44HC/annealed CMK-3 has 10-fold of thermal conductivity and enhanced thermal stability than RT44HC. The RT44HC/annealed CMK-3 has a large melting enthalpy of 177.8 J g−1and good thermal stability. The RT44HC/annealed CMK-3 has optical absorptive coefficient of visible range of solar spectrum, which identify seven-fold higher than RT44HC. The RT44HC/annealed CMK-3 has great photo-thermal performance, and the photo-driven energy charging and discharging rate of RT44HC/annealed CMK-3 is almost 30-fold larger than the RT44HC. The results show that the annealed CMK-3 is a great mesoporous carbon nanomaterial for phase change materials and the annealed CMK-3 based phase change material has great potential in solar thermal utilizations such as solar water heating system and solar heating building systems.Keywords:solar thermal systems;phase change material;annealed CMK-3;thermal conductivity;photo-driven charging and discharging rate
研究领域:
材料科学
·
能源工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROCHIMICA ACTA
·
2024
·Vol. 191
·期 10
·1-13
·
IF 5.3
Guo Liang,Zhou Shijin,Xue Jinyan,Liu Zenghui,Xu Shuqing,He Zhangxu,Yang Huaixia
A sandwich electrochemical sensor was fabricated based on multi-walled carbon nanotubes/ordered mesoporous carbon/AuNP (MWCNTs/CMK-3/AuNP) nanocomposites and porous core–shell nanoparticles Au@PdNPs to achieve rapid and sensitive detection of AFB 1 in complex matrices. MWCNTs/CMK-3/AuNP nanocomposite, which was prepared by self-assembly method, served as a substrate material to increase the aptamer loading and improve the conductivity and electrocatalytic activity of the electrode for the first signal amplification. Then, Au@PdNPs, which were synthesized by one-pot aqueous phase method, were applied as nanocarriers loaded with plenty of capture probe antibody (Ab) and signal molecule toluidine blue (Tb) to form the Au@PdNPs-Ab-Tb bioconjugates for secondary signal amplification. The sensing system could still significantly improve the signal output intensity even in the presence of ultra-low concentration target compound due to the dual signal amplification of MWCNTs/CMK-3/AuNP nanocomposites and Au@PdNPs-Ab-Tb. The method exhibited high selectivity, low detection limit (9.13 fg/mL), and strong stability to differentiate AFB 1 from other mycotoxins. Furthermore, the sensor has been successfully applied to the quantitative determination of AFB 1 in corn, malt, and six herbs, which has potential applications in food safety, quality control, and environmental monitoring. Graphical Abstract
研究领域:
分析化学
·
食品安全
·
环境监测
·
纳米技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CARBOHYDRATE POLYMERS
·
2023
·
IF 11.2
Miao Cheng,Yifan Yuan,Huaijia Jing,Jing Hu,Qianqian Liu,Tao Wei,Ruirui Wang,Wanfei Li,Bo Liu
Phase change materials (PCMs) have attracted numerous attention owing to their high energy storage density, cost-effective and operationally simple, however, the “solid-liquid” leakage and limited solar absorbance seriously hinder their widespread applications. Herein, an innovative chitosan/cellulose nanocrystal/CMK-3 (CS/CNC/CMK-3) aerogel based shape-stable PCM (SSPCM) was successfully synthesized, in which chemically cross-linked CS and CNC acted as three-dimensional supporting skeleton , CMK-3 endowed solar-to-thermal energy conversion ability and the impregnating polyethylene glycol (PEG) acted as the latent heat storage unit. The as-synthesized CS/CNC/CMK-3 aerogel/PEG (CCCA/PEG) showed ultrahigh melting/crystallization enthalpy of 178.5/171.1 J g −1 and excellent shape stability. The PEG was effectively embedded into the hierarchical porous architecture and the composite PCM could preserve its original shape without any leakage even compressed above the melting point of PEG. Meanwhile, the CCCA/PEG exhibited robust thermal reliability with an ultralow enthalpy fading rate of 0.030 ± 0.012 % per cycle over 100 thermal cycles. Intriguingly, the introduction of CMK-3 also significantly improved the solar-to-thermal energy conversion performance of CCCA/PEG, and a high solar-to-thermal conversion efficiency of 93.1 % could be realized. This work provided a potential strategy to design and synthesize high-performance sustainable SSPCM, which showed tremendous potential in the practical solar energy harvesting, conversion and storage applications.
研究领域:
材料科学
·
能源工程
·
环境科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2022
·
IF 9.136
Gaozu Liao,Peng Xu,Ping Lu,Xiaojiao Qing,Zhanjiang Yu,Yu Chang,Weirui Chen,Yiming Tang,Jing Wang,Xi Wang,Xukai Li,Laisheng Li,Dehua Xia
Single Co atoms dispersed on CMK-3 was synthesized and employed as efficient catalyst to degrade APAP in O 3 /PMS process. The results of morphology and structure characterization indicated that the as prepared catalyst possessed uniform array of mesoporous channel structure with a long-range. Co atoms were single atomic dispersed in CMK-3 skeleton with the form of CoN 4 coordination. The BET surface area and average pore diameter of 3.6% SA Co/CMK-3 were measured as 956 m 2 /g and 3.6 nm, respectively. For APAP degradation by 3.6% SA Co/CMK-3 + PMS/O 3 process, TOC removal efficiency reached to 60% and 78.9% in initial 1 min and 15 min, respectively. The influence of initial pH was investigated and demonstrated that APAP could be efficiently mineralized in a wide pH range. In addition, high mineralization rates were also achieved for other refractory organics (nitrobenzene and sulfamethoxazole). Radical quenching experiments and ESR indicated that SO 4 •− , •OH and 1 O 2 were all responsible for APAP degradation. DFT simulations elucidated that single Co atoms and N-heteroatoms on 3.6% SA Co/CMK-3 served as dual reaction sites for PMS and O 3 decomposition, which enhanced the ROS generation and APAP mineralization.
研究领域:
环境科学
·
催化
·
水处理
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2025
·
IF 7.7
Xingxing Yu,Faxun Wang,Huakang Zong,Yufei Gan,Guotao Duan,Yuanyuan Luo
The modification of ionic liquid electrolytes is of particular importance for the development of high-performance electrochemical oxygen sensors with zero power consumption but still quite challenging. Herein, we designed and synthesized an electrochemical oxygen sensor based on the modified Pt/CMK-3-COOH-[EMIM][OAc] ionic liquid as composite electrolyte, where the -COOH functional group was introduced by acidifying CMK to provide hydrogen protons, and then Pt nanoparticles with different contents were loaded to improve the activity of the sensor towards O 2 gas as well as the conductivity of ionic liquid. Such composite ionic liquid sensor exhibits excellent O 2 detection ability with high sensitivity (0.58 μA/[%O 2 ]), high stability, wide detection range (0.4-10%), and zero-power consumption, along with the detection limit as low as 0.4%. Furthermore, it has humidity-independent gas-sensing characteristic. Moreover, density functional theory (DFT) calculations combined with experimental results were applied to deeply unveil the improved O 2 sensing mechanism. Compared with CMK, the introduction of Pt/CMK-3-COOH material increases the conductivity of the ionic liquid, decreases the adsorption energy of the sensor for O 2 and hydrogen protons, promotes the oxygen reduction reaction, and simulates the transfer of effective charge, thereby significantly improving O 2 sensing. This work provides a high-performance ionic liquid oxygen sensor, showing potential application in zero-power consumption and low concentration O 2 detection.
研究领域:
电化学传感
·
生物医学工程
·
分子诊断
·
即时检测
·
生物传感器
·
转化医学
✓ 已验证
产品关联
DOI
高影响因子
Coatings
·
2025
·Vol. 15
·期 9
·1027
·
IF 2.8
Minglei Yang,Zhenhong Xu,Chongjun Tang,Shuaijie Wang,Zhourong Xiao,Fei Ye
This research introduces a synergistic photoelectrocatalytic (PEC) system designed for the effective degradation of tetracycline (TC), integrating a PO43−-grafted Mo-doped BiVO4(PO43−-Mo:BiVO4) photoanode with a Pd-loaded ordered mesoporous carbon (Pd/CMK-3) cathode. The incorporation of Mo doping and PO43−modification significantly improved the photoanode’s charge separation efficiency, achieving a photocurrent density of 2.9 mA cm−2, and fine-tuned its band structure to enhance hydroxyl radical (·OH) generation. Meanwhile, the Pd/CMK-3 cathode promoted a two-electron oxygen reduction reaction pathway, producing hydrogen peroxide (H2O2) and facilitating molecular oxygen activation via atomic hydrogen (H*) intermediates. Under optimized conditions—1.0 V vs. Ag/AgCl of anodic potential, pH 6.58, and oxygen saturation—the combined system accomplished 80% TC degradation within 60 min, markedly surpassing the performance of the photoanode (72%) or cathode (71%) alone. Notably, this synergistic approach also reduced energy consumption to 0.0065 kWh m−3, outperforming individual components. Radical quenching experiments and liquid chromatography–mass spectrometry (LC-MS) analysis revealed that the photogenerated holes (h+) and ·OH were the key reactive species responsible for TC mineralization. The system demonstrated remarkable stability, with only a 2.96% decline in activity, and effectively degraded other contaminants, such as phenol, 4-chlorophenol, and ciprofloxacin. This study highlights an energy-efficient PEC strategy that harnesses the combined strengths of anodic oxidation and cathodic molecular oxygen activation to significantly enhance the removal of organic pollutants.
研究领域:
环境化学
·
材料科学
·
催化化学
·
水处理技术
·
功能材料
·
电化学
·
光催化
·
污染物降解
✓ 已验证
产品关联
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2024
·
IF 4.9
Lixia Luo,Jinglin Shui,Yingying Gu,Dandan Wang,Jiangyang Qin,Yanan Wang,Yong Mei
In order to detect the cervical cancer biomarker squamous cell carcinoma antigen (SCCA) in human serum, an electrochemical immunosensor was constructed. Zirconium 1,4-dicarboxybenzene MOF (UiO-66), with a high specific surface area, was coupled with gold nanoparticles (AuNPs), creating the UiO-66@AuNPs nanomaterial. This coupling increased the sensitivity of the electrochemical immunosensor by providing many biological binding sites for antibodies to bind to Au-S bonds. Then, mesoporous carbon (CMK-3) was added to the UiO-66@AuNPs nanomaterial to obtain a CMK-3@UiO-66@AuNPs nanocomposite. This further increased the electron transfer proficiency of the material and enhanced the electrochemical signal. Finally, the sensitive detection of squamous cell carcinoma antigen (SCCA) was made possible by unique immunological responses between antigens and antibodies. Transmission electron microscopy (TEM) analysis of CMK-3@UiO-66@AuNPs revealed embedded surfaces and voids; cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) confirmed the successful assembly of the electrochemical immunosensor. The developed electrochemical immunosensor demonstrated good linearity (R 1 2 = 0.999) from 0.01 pg/mL to 10,000 pg/mL, which is the concentration range of SCCA in human serum. The limit of detection was 0.0034 pg/mL (at an S/N ratio of 3). The immunosensor exhibited excellent precision, stability and selectivity, with a high rate of recovery (98.26–101.8 %). The experimental validation studies demonstrated that the electrochemical immunosensor was effective for the detection of SCCA in human serum, offering a novel method for the early diagnosis and dynamic surveillance of cervical cancer.
研究领域:
生物医学工程
·
癌症研究
·
电化学
·
纳米技术
·
分析化学
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2020
·
IF 5.774
Xiaoxiang Cheng,Weiwei Zhou,Daoji Wu,Congwei Luo,Ruibao Jia,Peijie Li,Lu Zheng,Xuewu Zhu,Heng Liang
In this study, ordered mesoporous carbons (OMCs), i.e., CMK-3 and CMK-8 were pre-deposited on ultrafiltration membrane surface to alleviate membrane fouling by organic matter in the water. CMK-3 shows a typical 2D hexagonal symmetrical structure with long straight parallel channels, while CMK-8 exhibits a 3D porous structure with cubic channels. The pre-deposited CMK-3/CMK-8 layers exhibited significantly superior performance for both flux enhancement and fouling mitigation, whereas powdered activated carbon (PAC) showed limited influence. The fouling mechanism was apparently altered by the OMCs pre-deposition layers, and pore blocking always dominated throughout the filtration process without the formation of cake filtration. In comparison with PAC, CMK-3 and CMK-8 were more effective for the rejection of tryptophan-like protein substances, which were the major foulants causing membrane fouling. The effects of pollutant fraction and deposited amount (i.e., 6, 12, 25 and 50 g/m 2 ) were systematically explored, and the results indicated that this technology was more efficient for alleviating the fouling induced by humic acid and bovine serum albumin, whereas ineffective for sodium alginate fouling, and the optimal deposited amount varied with the pollutant fraction. CMK-3 exhibited significantly superior performance than CMK-8, likely due to its long straight parallel channels with lower internal resistance for pollutants adsorption. Both adsorption and size exclusion of the pre-deposited layers contributed to fouling mitigation. These results demonstrate that pre-depositing with OMCs as alternatives to conventional PAC shows promising potential for mitigating membrane fouling in water treatment.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
ENERGY & FUELS
·
2023
·
IF 5.3
Peng Guo,Songling Zhang,Xiuwu Liu,Shijie Zhu,Huimin Li,Jilin Cao
Compared with the synthesis process of the CMK-3 material, the ordered mesoporous carbon (OMC) materials were successfully synthesized by simplifying the synthesis steps. The silica/P123 composite material that had formed nanostructures was not filtered, washed, and calcined to form SBA-15 material, but it was directly used as a hard template to synthesize OMC materials. The self-assembly of block polymers (P123) in the pore space was not removed but directly carbonized as partial carbon source. The template agent (surfactant P123) was not removed but used as part of the carbon source. The synthetic materials exhibited large pore volume, high specific surface area, regular hexagonal pore structures, and good long-range order, which was confirmed by the 77 K N2 adsorption–desorption isotherms, transmission electron microscopy (TEM), and small-angle X-ray diffraction (XRD). The synthetic materials were applied to capture carbon dioxide, and the results of carbon dioxide capture were better than those of the CMK-3 material reported previously. Under the conditions of 3.4 MPa pressure and 275 K temperature, the CO2 capture capacity of the dry synthetic MC-1.5–0.8 material without water was 25 mmol/g at 275 K, which was 1.4 times that of the dry CMK-3 material. In addition, the CO2 capture capacity of the same pre-adsorbed water MC-1.5–0.8 sample with Rw = 3.8 at 3.3 MPa was 47.6 mmol/g, which was 1.9 times that of the dry MC-1.5–0.8 sample.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
ACS Sustainable Chemistry & Engineering
·
2018
·
IF 6.14
Liqiao Zhong,Yong Lu,Haixia Li,Zhanliang Tao,Jun Chen
Aqueous rechargeable sodium-ion batteries (ARSIBs) are promising candidates for large-scale energy storage applications due to their high safety, low cost, and environmental friendliness. However, appropriate anode materials with high capacity for ARSIBs are limited, and their cycling stability is generally unsatisfactory. Here we report high-performance ARSIBs with polyacrylamide hydrogel as electrolyte and alloxazine (ALO) encapsulated in CMK-3 as anode. The hydrogel with solid content of 60% could effectively mitigate the dissolution issue of sodiated ALO because its cross-linked structure is helpful to reserve H2O. The ALO/CMK-3 anode based on a two-electron transfer reaction could deliver a high capacity of 160 mA h g–1. The introduction of CMK-3 could improve the electrical conductivity of ALO and further reduce the dissolution of sodiated ALO because of its high conductivity and nanochannel structure. The full ARSIBs exhibit an energy density of 50 W h kg–1 (based on the total mass of active electrode materials) with good capacity retention of 90% after 100 cycles at 2 C and high rate capability of 146 mA h g–1 at 10 C (1 C = 250 mA g–1). This work paves the way to construct high-performance ARSIBs with high-capacity organic anode and hydrogel electrolyte.
研究领域:
能源材料
·
电化学
·
电池技术
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）