MATERIALS & DESIGN
·
2025
·
IF 7.9
Mengjiao Jiao,Yang Zhang,Guishang Pei,Zhuoyang Li,Xuewei Lv
This study focused on the high-temperature phase equilibrium of the Fe 2 O 3 -TiO 2 system by employing the classic phase equilibration and quenching method, X-ray diffraction, electron-probe microanalysis, and thermal analysis experiments. The solubility of the hematite, pseudobrookite, and rutile phases as the equilibrium temperature rose from 1100 °C to 1450 °C was determined. Besides, the solubility of TiO 2 in the spinel phase at 1450 °C was verified by experiments. A comprehensive comparison with the phase diagram optimized by Panda indicates that the solubility of solid solutions involved in the Fe 2 O 3 -TiO 2 system should be larger than the predicted one. Additionally, the ordered rutile phase was transformed into the high-temperature rutile-derived crystallographic shear structure at 1400 °C with Fe 2 O 3 higher than 15 mol%. Furthermore, the eutectic reaction of liquid → pseudobrookite + rutile occurred at 1512 °C. The liquidus was determined to be 1512 °C and 1535 °C at 30 and 75 mol% of TiO 2 , respectively. These measured phase equilibrium data are expected to provide reliable input for future thermodynamic reassessments of the Fe 2 O 3 -TiO 2 system within the CALPHAD framework.
研究领域:
材料科学
·
热力学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2015
·
IF 2.999
Rong Li,Yuefa Jia,Naijing Bu,Jun Wu,Qiang Zhen
Using home-made Fe 2 O 3 /TiO 2 nanopowders as raw material, Fe 2 O 3 /TiO 2 composite ceramic was fabricated in order to use as photocatalysts in practical water purification treatment. The effects of sintering temperature on its phase variation, physical properties and photocatalytic properties were investigated. With sintering temperature increases, the anatase TiO 2 transforms into rutile phase, and reacts with hematite Fe 2 O 3 to form pseudobrookite Fe 2 TiO 5 . Above 800 °C, only Fe 2 TiO 5 and rutile TiO 2 were observed. Correspondingly, the porosity and the photocatalytic activity of Fe 2 O 3 /TiO 2 composite ceramic decreased, especially for samples sintered at 1000 °C, obvious decline in degradation efficiency was observed. The further investigation on photocatalytic degradation of methyl blue (MB) were carried out using ceramics sintered at 880 °C (TFC-880), which exhibited moderate physical and photocatalytical properties. The result showed that TFC-880 exhibited a high photodegradation capability for MB under either UV or visible light. Even in the third circle, it also showed a high degradation rate, meaning it has an extended application such as water treatment.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2020
·
IF 3.83
Hui Mei,Shixiang Zhou,Mingyang Lu,Yong Zhao,Laifei Cheng
For real-time environmental monitoring and gas detection under harsh conditions, gas sensors with high reliability, sensitivity, and selectivity are in increasing demand. Therefore, pine-branch-like α-Fe 2 O 3 /TiO 2 with a core–shell hierarchical heterojunction structure was designed and fabricated for ethanol sensing. The heterojunction increased the O adsorption, resulting in the formation of more chemisorbed O species for reaction with the target gas. Moreover, the pine-branch-like morphology formed three-dimensional hollow holes as channels for molecule diffusion and adsorption. Compared with gas-proof structures, the hollow regions can realize gas diffusion in the inner and outer surfaces of materials simultaneously. Further, in contrast to aggregated structures, the fibers were separated from each other, and charge conduction between the fibers needed to pass through the surface sensing layer at the fiber boundary; thus, the overall resistance change of the sensors was significantly affected by the response of the heterojunction to the target gas. Consequently, the α-Fe 2 O 3 /TiO 2 sensor exhibited a high response value of 40.4 toward 500 ppm ethanol gas and had excellent selectivity to ethanol. The proposed strategy may facilitate the design and construction of effective heterojunctions and nanostructures for gas sensing.
研究领域:
材料科学
·
传感器技术
·
纳米科技
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS
·
2018
·
IF 2.207
Hui Liu,Zhi-Guang Zhang,Xiao-Xiong Wang,Guang-Di Nie,Jun Zhang,Shan-Xiang Zhang,Ning Cao,Shi-Ying Yan,Yun-Ze Long
Highly flexible Fe 2 O 3 /TiO 2 composite nanofibers were successfully synthesized via electrospinning followed by high-temperature calcination . The morphologies and structures of Fe 2 O 3 /TiO 2 nanofibers were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and ultraviolet-visible (UV-Vis) spectroscopy, and their optical properties , photocatalysis and photodetection properties were also measured. The flexible nanofibers possess large specific surface area, and can be recycled by a magnet. Moreover, the absorption region has been extended from the UV region to the visible region, improving the performance of photocatalyst under visible light radiation . In addition, the formation of Fe 2 O 3 /TiO 2 heterostructures suppresses the recombination of photogenerated electron-hole pairs, which also improves the photocatalyst behavior. Particularly, these nanofibers can also work as a sensitive UV detector, which offers in situ monitor method of such photocatalysis materials.
研究领域:
材料科学
·
环境科学
·
光学工程
✓ 已验证
产品关联
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2016
·Vol. 18
·期 13
·9176-9185
·
IF 4.449
Xin Li,Huiming Lin,Xiang Chen,Hao Niu,Jiuyu Liu,Ting Zhang,Fengyu Qu
The design and synthesis of unique novel heterostructures for high-performance photocatalytic activity has exerted a tremendous fascination and has recently attracted intensive attention. In this work, a branch-like α-Fe2O3/TiO2 heterostructure has been synthesized controllably through an electrospinning method combined with a hydrothermal approach. The backbone of the heterostructure is composed of a 3D porous TiO2 nanofiber (∼70 nm in diameter) network with plenty of α-Fe2O3 nanorods (100–200 nm in length) deposited on them. The novel branch-like nanocomposites have an abundantly porous structure as well as large surface areas (up to 42.8 m2 g−1). In addition, their visible light photodegradation behaviour towards organic dyes, including Congo red (CR), methylene blue (MB), eosin red (ER) and methyl orange (MO), was investigated. Their excellent photocatalytic performances are attributed to their large surfaces, improved visible light absorption and high separation efficiency of the photogenerated electrons/holes. Furthermore, the degradation process was further studied by varying the amount of α-Fe2O3 deposited. The sample α-Fe2O3/TiO2-3 possessed the best performance to efficiently decolor CR solution even at a high concentration of 50 mg L−1 (160 min, 94 mg g−1), ascribed to the high adsorption capacity derived from the large surface, strong electrostatic interaction and structural match between α-Fe2O3/TiO2-3 and CR. These α-Fe2O3/TiO2 heterostructures exhibit great potential for decontamination of organic pollutants in waste water under visible light.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Materials Research Express
·
2018
·Vol. 6
·期 3
·035503
·
IF 1.151
Qiwei Shi,Jianxiong Liu,Jianzheng Zhen,Guanqun Zhang,Cheng Liu,Qi Cheng,Zhaolin Zhan
The precursor of Fe(OH)3, C and TiO2 was synthesized by a simple one-step hydrothermal method. Then, the of C in the composite was eliminated by calcination at 500 °C for 5 h in an air atmosphere. Thereby, a Fe2O3@TiO2 microspheres composite material is synthesized. The incorporation of Fe2O3 helps provide high specific capacity, high speed cycling and stable life performance. The first discharge capacity of Fe2O3@TiO2 microspheres is 688 mAh g−1, with higher discharge performance, higher reversible capacity and higher cycle performance. Moreover, the 2nd to 50th charge and discharge of Fe2O3@TiO2 microspheres, the capacitance retention rate exceeds 90%. The outstanding stable cycling and well rate performance suggest that Fe2O3@TiO2 microspheres have great potential to be applied as anode material for lithium ion batteries.
研究领域:
材料科学
·
能源存储
✓ 已验证
DOI
高影响因子
SENSORS
·
2024
·Vol. 24
·期 8
·2604
·
IF 3.4
Zhihua Zhao,Zhenli Lv,Zhuo Chen,Baocang Zhou,Zhigang Shao
Metal oxide semi-conductors are widely applied in various fields due to their low cost, easy processing, and good compatibility with microelectronic technology. In this study, ternary α-Fe2O3/TiO2/Ti3C2Txnanocomposites were prepared via simple hydrothermal and annealing treatments. The composition, morphology, and crystal structure of the samples were studied using XPS, SEM, EDS, XRD, and multiple other testing methods. The gas-sensing measurement results suggest that the response value (34.66) of the F/M-3 sensor is 3.5 times higher than the pure α-Fe2O3sensor (9.78) around 100 ppm acetone at 220°C, with a rapid response and recovery time (10/7 s). Furthermore, the sensors have an ultra-low detection limit (0.1 ppm acetone), excellent selectivity, and long-term stability. The improved sensitivity of the composites is mainly attributed to their excellent metal conductivity, the unique two-dimensional layered structure of Ti3C2Tx, and the heterojunction formed between the nanocomposite materials. This research paves a new route for the preparation of MXene derivatives and metal oxide nanocomposites.
研究领域:
材料科学
·
传感器技术
·
纳米技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF POROUS MATERIALS
·
2017
·Vol. 24
·期 5
·1227-1235
·
IF 1.624
Su Huanhuan,Lv Xiang,Zhang Zhengyi,Yu Jiajie,Wang Tianhe
Fe 2 O 3 –TiO 2 porous ceramic (Fe/TiPC) beads with photo-catalytic performances and high adsorption capacities were prepared by a simple high temperature solid reaction and were applied for arsenic removal from drinking water. The microstructure and morphology of Fe/TiPC were characterized by X-ray diffraction and scanning electron microscopy. More than 90% removal ratio for As (III) and As (V) were respectively achieved by Fe/TiPC within 2 h under UV irradiation. The Langmuir capacity values of Fe/TiPC for As (III) and As (V) were 13.86 and 15.73 mg/g, respectively. In addition, Fe/TiPC could be reused for up to five times without significant reduction in the photocatalytic sensitivity and adsorption capacity aspects. Good catalytic oxidation performances and high adsorption capacities as well as a sample preparation for Fe/TiPC suggest that the composites may have practical prospects for the As (III) and As (V) removal from contaminated water.
研究领域:
环境科学
·
材料科学
·
水处理
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2018
·Vol. 25
·期 23
·22455-22463
·
IF 2.8
Wang Pingping,Dong Faqin,Liu Mingxue,He Huichao,Huo Tingting,Zhou Lei,Zhang Wei
Photoelectrochemical process is an environmentally friendly technology and has a wide application in the control of environmental pollutants. Efficient nanophotocatalysts responsive to visible light are still highly attractive. In this work, α-Fe 2 O 3 /TiO 2 were grown on fluorine doped tin oxide (FTO) substrates by hydrothermal method for photoelectrochemical reduction of Cr(VI). Compared with the separate α-Fe 2 O 3 and TiO 2 electrodes, the composite α-Fe 2 O 3 /TiO 2 electrodes show higher photocurrent density. Under visible light irradiation, 100% removal efficiency of Cr(VI) was obtained after 40 min treatment. The composite α-Fe 2 O 3 /TiO 2 electrodes showed an enhanced absorbance in visible light region and had good stability to photoelectrochemical reduction of Cr(VI). The role of hole scavengers (citric acid and oxalic acid) and pH values was systematically investigated. This novel intensification approach provides new insight on the application of photoelectrochemical reduction in environmental remediation.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MOLECULAR LIQUIDS
·
2024
·
IF 5.3
Caixia Deng,Shuang Li,JiaYu Wang,Qiang Yang,Hui Chen,Fenglin Tang,Xiupei Yang
In this work, flower-like TiO 2 (TiO 2 -F) was first prepared by modulating the morphology of TiO 2 , and then, α-Fe 2 O 3 was loaded onto TiO 2 -F to successfully prepare α-Fe 2 O 3 /TiO 2 -F heterojunction materials. The material showed excellent degradation properties of doxycycline hydrochloride under visible light. The photocatalytic degradation efficiency of α-Fe 2 O 3 /TiO 2 -F2 for doxycycline hydrochloride under visible light reached 95.76 % in 120 min, and its pseudo-first-order degradation rate constant was 0.02647 min −1 , which was 3.68 and 2.01 times higher than those of α-Fe 2 O 3 and TiO 2 alone, respectively. This good photocatalytic performance is attributed mainly to the introduction of α-Fe 2 O 3 to form a Type II heterojunction with floral TiO 2 (TiO 2 -F), which is capable of promoting the separation of electron–hole pairs of photocatalysts and exhibiting a stronger redox capacity. The material exhibits notable stability and maintains high degradation efficiency even after undergoing multiple cycles. Furthermore, free radical trapping experiments and electron spin resonance (ESR) characterization revealed that hydroxyl radicals play a dominant role in this system. Finally, the degradation pathways were analyzed, and relevant toxicological analyses were performed, indicating that the toxicity of doxycycline hydrochloride gradually decreased during the photocatalytic degradation process.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2023
·
IF 7.7
Liu Yang,Jing Li,Guoqiang Cao,Yiyan Yang,Wen Luo,Zhiqi Zhang,Lizhi Feng,Xinglai Zhang,Baodan Liu
This study reports on the development of highly-efficient Pt/CuO-Fe 2 O 3 /TiO 2 monolithic catalysts for the low-temperature conversion of NO to N 2 via CO-SCR. In this case, ultrathin TiO 2 nanosheet arrays are designed to in situ grow on flexible Ti mesh to provide more spaces/areas for the loading of highly-dispersed Fe 2 O 3 and CuO active components. Furthermore, Pt nanoparticles with an average size of 1.30 nm are effectively decorated on the surface of CuO-Fe 2 O 3 /TiO 2 . The H 2 -TPR and NO-TPD results demonstrate that the excellent synergistic effect between TiO 2 , CuO, Fe 2 O 3 and trace amounts of Pt is conducive to enhance the adsorption of NO and finally promote the CO-SCR. The obtained Pt/CuO-Fe 2 O 3 /TiO 2 catalysts exhibit excellent CO-SCR performance with 100 % NO conversion, and 100 % N 2 selectivity at 250 °C, showing great potential of de-NO x application by using toxic CO as reductant in industry.
研究领域:
环境科学
·
催化材料
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2015
·Vol. 5
·期 51
·40764-40771
·
IF 3.84
Rong Li,Yuefa Jia,Jun Wu,Qiang Zhen
The degradation behavior of oxytetracycline (OTC) in aqueous solution using Fe2O3–TiO2 nanopowders (Fe2O3–TiO2 NPs) as photocatalysts under UV/visible light was investigated in this paper. Fe2O3–TiO2 NPs photocatalysts synthesized using co-precipitation were characterized by XRD, TEM, FT-IR and UV-vis DRS. Fe2O3–TiO2 NPs with 45 wt% Fe2O3 exhibited higher photocatalytic activity than others. The photocatalytic degradation of OTC shows a maximum efficiency at pH = 5.5 under both UV/visible light due to the surface adsorption. The intermediate products during the photocatalytic degradation of OTC were detected by LC-MS/TOF. Seven main intermediates were formed, and their evolution was discussed. On the basis of the evidence oxidative intermediate formation and a detailed degradation path way of OTC by 45 Fe2O3–TiO2 NPs are proposed.
研究领域:
环境科学
·
化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）