CHEMICAL ENGINEERING RESEARCH & DESIGN
·
2019
·
IF 3.073
Suresh Mutyala,Madhavi Jonnalagadda,Harisekhar Mitta,Raveendra Gundeboyina
MIL-101 (Cr) was synthesized by a hydrothermal method and used as support to prepare a series of polyethylenimine (PEI) incorporated MIL-101 (Cr) by wet impregnation method. All characterization results revealed that the structure of MIL-101 (Cr) was well-maintained by the incorporation of polyethylenimine and confirmed the presence of PEI within MIL-101 (Cr). The CO 2 adsorption studies were carried out in a fixed bed reactor from 30 to 90 °C, 1 bar. The adsorption of CO 2 has been increased by the incorporation of PEI. It was due to the chemical interaction between the NH 2 and CO 2 groups to form a carbamate. The high CO 2 adsorption capacity 3.81 mmol g −1 was shown by 70 wt% PEI loaded MIL-101 (Cr) at 75 °C, 1 bar, because of more number of NH 2 groups and a high number of CO 2 molecules diffusion. Its adsorption capacity was 4.7 times higher than the adsorption capacity of MIL-101 (Cr) (0.80 mmol g −1 ). Moreover, in moisture condition, CO 2 adsorption capacity was increased to 4.4 mmol g −1 by the formation of ammonium bicarbonate and showed good adsorption stability throughout each adsorption-desorption cycle. The Avrami adsorption kinetic model was well fitted with experimental breakthrough CO 2 adsorption data of MIL-101 (Cr)-PEI-70. It suggested that the adsorption of CO 2 on PEI incorporated material was chemical adsorption.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
INORGANICA CHIMICA ACTA
·
2017
·
IF 2.002
Tian Zhao,Ling Yang,Peiyong Feng,Irina Gruber,Christoph Janiak,Yuejun Liu
MIL-101(Cr), one of the best investigated and widely used metal–organic frameworks, has been easily synthesized with particle diameters in the range from 387(28) nm to 90(10) nm by using acetic acid as a modulator . The particle size of MIL-101(Cr) decreased with increasing acetic acid concentration. The decrease of size in high concentration of acetic acid may be explained with the efficient suppression of the framework extension. In a selected condition, MIL-101(Cr) possessing an average diameter of about 90 nm can be prepared easily and reproducibly in gram-scale, with high BET-surface areas (3200–3500 m 2 /g) and fairly good yield (60–75%).
研究领域:
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
CHEMISTRY AND ECOLOGY
·
2024
·
IF 1.3
Zhenpeng Li,Dongmei Yan,Jun Li,Ziwei Mai,Fuchuan Huang
Hexavalent chromium (Cr(VI)) is regarded as a water pollutant because of its high toxicity in aquatic environments. In this study, polyethyleneimine-functionalised NH2-MIL-101(Cr) (PEI@NH2-MIL-101(Cr)) was fabricated by a facile wet impregnation method, and its effectiveness at removing Cr(VI) from wastewater was systematically investigated. As suggested by the experimental findings, pH was a significant determinant of Cr(VI) uptake by the fabricated PEI@NH2-MIL-101(Cr). Preferable depiction of adsorption system was achievable with the Langmuir adsorption model and the pseudo-order 2 kinetic model. At 288, 298, and 308 K, the highest adsorbability values were 241.55, 310.56, and 408.16 mg g−1, respectively. Processes like electrostatic attraction, reduction and chelation helped promote the Cr(VI) elimination. SO42− ions had a relatively large impact on the Cr(VI) adsorption compared with other coexisting ions such as NO3−, Cl− and H2PO4−1. Because of its properties of high adsorption capacity and Cr(VI) detoxification, the potential of PEI@NH2-MIL-101(Cr) in the Cr(VI) elimination from wastewater appears to be promising.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Materials Today Communications
·
2024
·
IF 3.7
Chunlong Qiu,Haiyang Sun,Yeyang Ni,Zhenjiang Dou,Ming Xia,Zhaoyang Fei,Zhuxiu Zhang,Mifen Cui,Qing Liu,Xu Qiao
The impressive water stability demonstrated by MIL-101(Cr) highlights its considerable potential for the effective elimination of organic contaminants from wastewater. Nevertheless, the limited availability of adsorption sites within MOFs leads to an unsatisfactory capacity for tetracycline (TC) adsorption. In this case, the lanthanum modified MIL-101(Cr) porous adsorbents, termed as nLa-MIL-101(Cr), were successfully synthesized using a post-synthetic modification method. Through various characterization analyses, it was confirmed that lanthanum exists in the form of La(OH) 3 within the adsorbents, and all adsorbents also preserved the original structure as MIL-101(Cr). The results of static adsorption experiments demonstrated that, compared to the original material, the adsorption capacity of 1La-MIL-101(Cr) for TC increased by 3.5 times. Further experiments demonstrated that the adsorbent exhibits remarkable ion interference resistance and cycle stability. Finally, based on X-ray photoelectron spectroscopy, the adsorption mechanism was primarily attributed to the coordination between TC molecules and metals active site, while electrostatic interactions also played a significant role in the process. This study has developed a highly efficient adsorbent for the treatment of TC-contaminated wastewater, which reflects promising practical application prospects.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Nanomaterials
·
2023
·Vol. 13
·期 14
·2072
·
IF 5.3
Xu Zhang,Bo Tian,Zhiheng Ma,He Wang,Zhixuan Cheng,Jiaqiang Xu
As a volatile air pollutant, formaldehyde can enter people’s living environment through interior decoration, furniture and paint, causing serious harm to human health. Therefore, it is necessary to develop a sensor for the real-time detection of formaldehyde in low concentrations. According to the chemical interaction between amino groups and formaldehyde, a MIL-101(Cr) aminated-material-based formaldehyde cantilever sensor was prepared, of which ethylenediamine- functionalized MIL-101(Cr) named ED-MIL-101(Cr)) showed the best gas sensing performance. Using quasi-in situ infrared spectroscopy, ED-MIL-101(Cr) was found bound to formaldehyde through a Schiff base. The adsorption enthalpy of formaldehyde-bound ED-MIL-101(Cr) was −52.6 kJ/mol, which corresponds to weak chemical adsorption, so the material showed good selectivity. In addition, ED-MIL-101(Cr) has the most active sites, so its response value to formaldehyde is larger and it takes longer to reach saturation adsorption than bare MIL-101(Cr). Through the research on the gas sensing performance of functionalized MIL-101(Cr) material, we found that it has a strong application potential in the field of formaldehyde monitoring, and the material performance can be quantitatively and accurately evaluated through combining calculation and experimentation for understanding the gas sensing mechanism.
研究领域:
材料科学
·
环境科学
·
分析化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Materials
·
2022
·Vol. 15
·期 16
·5763
·
IF 3.748
Minmin Zou,Hexin Zhu,Ming Dong,Tian Zhao
As one of the most important prototypical chromium-based MOFs, MIL-101(Cr) is well-studied and widely employed in various scientific fields. However, due to its small capture window sizes and curved internal apertures, its application in large molecular removal is quite limited, and given its high stability and high synthetic temperature (>200 °C), it is difficult to achieve hierarchically porous MIL-101(Cr). In our study, hierarchically porous MIL-101(Cr) involving a high macro-/meso-/micropores ratio was designed and synthesized using acetic acid as an additive and silicon dioxide (SiO2) nanoparticles as a template. The optimal hierarchically porous MIL-101(Cr) (A-4) possessed a high specific surface area (2693 m2g−1) and an abundant macro-/mesoporous structure with the addition of SiO2of 200 mg. Compared with the control sample (A-0) with a less macro-/mesoporous structure, A-4 showed good adsorption properties for both coomassie brilliant blue R-250 (CBB, 82.1 mg g−1) and methylene blue (MB, 34.3 mg g−1) dyes, which were 1.36 times and 9.37 times higher than those of A-0. Moreover, A-4 also had good recyclability, and the removal rate of CBB was still higher than 85% after five cycles of adsorption.Keywords:MIL-101(Cr);SiO2;dye adsorption;template
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
International Journal of Refrigeration
·
2025
·
IF 3.8
Shuyi Yao,Zhongbao Liu,Shijie Li,Zhipeng Qie
Improving water vapor adsorption performance at low humidity and enhancing thermal conductivity are beneficial for the performances of adsorption refrigeration materials. In this study, MIL-101(Cr) was integrated with graphene oxide (GO) and calcium chloride (CaCl₂) to develop high-performance composite adsorbents. The materials were characterized by XRD, Raman spectroscopy, nitrogen adsorption-desorption, and thermal conductivity measurements. Adsorption and desorption tests revealed that the MIL-101(Cr)/2% GO + 20% CaCl₂ composite exhibited the best performance, achieving a dynamic adsorption capacity of 0.368 g/g and a 36% increase in thermal conductivity compared to pure MIL-101(Cr). Meanwhile, the heat and mass transfer performance of the materials and the COP and SCP of the system were analyzed by modeling the adsorbent and the system under the corresponding operating conditions, and MIL-101(Cr)/2% GO + 20% CaCl₂ showed the best performance among all the samples of the present study in all these models. Furthermore, the composite demonstrated excellent stability after 50 adsorption-desorption cycles, retaining a desorption efficiency above 93%. The synergistic effects of GO and CaCl₂ significantly improved both water vapor adsorption and thermal conductivity, making this composite a promising candidate for energy-efficient adsorption refrigeration systems.
研究领域:
材料科学
·
能源工程
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2024
·
IF 8.1
Shaoan Cheng,Yangxi Li,Zhen Yu,Yuqing Su
Adsorption can be used as a pollutant removal method to solve the increasingly serious problem of synthetic dye pollution and metal organic framework (MOF) is considered as a novel adsorbent for its unique structure. However, the high cost and high toxicity during the synthesis procedure of MOFs like MIL-101(Cr) limited their potential on the large-scale production and application. In this paper, waste PET plastic was depolymerized to prepare terephthalic acid (TPA) as an organic linker to synthesize MIL-101(Cr). Besides, Hydrofluoric acid (HF) was not added during the synthesis to avoid poisonous pollution. MIL-101(Cr) was applied to the adsorption of anionic dyes reactive red 2 (RR2) and reactive blue 19 (RB19). The batch experiments exhibited kinetic data best fitted the pseudo-first-order model (PFO) with the adsorption capacity of 662.87 (RR2) and 863.67 mg g -1 (RB19). The isotherm adsorption data fitted well with the Freundlich isotherm, indicating formation of multilayer coverage over the surface of MIL-101(Cr). The highest regeneration rate of MIL-101(Cr) at the fourth cycle was 91.18 and 91.44 % after RR2 and RB19 adsorption. X-ray photoelectron spectroscopy (XPS) technique and Fourier Transform Infrared (FTIR) spectroscopy both indicated the possible adsorption mechanism of MIL-101(Cr) toward RR2 and RB19 could be attributed to electrostatic interactions, hydrogen bonding, and the π-π stacking. This work proposed a novel method using waste plastics as raw materials to synthesize eco-friendly pollutant adsorbent, which had an enlightening effect on pollutant treatment.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2020
·
IF 3.99
Yuan Tang,Xiaohong Yin,Manman Mu,Yue Jiang,Xiaoli Li,Hao Zhang,Tianwei Ouyang
A series of anatase TiO 2 @MIL-101(Cr) was synthesized using the solvothermal method for photocatalytic degradation of bisphenol A (BPA). The characterization of the composites showed that they had an octahedral shape that was similar to that of MIL-101(Cr), but the particle size was reduced to about 300–500 nm. The amount and surface area of the TiO 2 in the composites jointly influenced the photocatalytic degradation; in optimal conditions, 59 % TiO 2 @MIL-101(Cr) could achieve 99.4 % BPA degradation in 240 min under UV irradiation. This superior photocatalytic performance was the result of the effective separation of electron-hole pairs and a narrow band gap. Moreover, the optimal composite exhibited excellent stability, indicating its suitability for reuse. Reasonable pathways of BPA degradation were proposed based on the detected intermediates during the degradation, where the oxidative radical O 2 − played a dominant role.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF SOLID STATE CHEMISTRY
·
2025
·
IF 3.5
Mengyao Li,Ping Wu,Xiaoli Han,Shanshan Shi,Shiping Zhang,Li Wang,Min Xu,Xiulan Huai
Adsorption-based thermal energy conversion systems offer a sustainable solution for space heating and cooling applications. However, due to the limited performance of solid adsorbents, the large-scale application of this technology still requires further research. To address this challenge, we developed a composite adsorbent by integrating a graphene oxide (GO)-modified metal-organic framework (MIL-101(Cr)) with LiCl. The material was characterized using a variety of techniques to assess its improvement in three areas: water adsorption performance, heat propagation rate and stability. The synthesized material was systematically characterized to evaluate three key performance parameters: water adsorption capacity, thermal conductivity, and cyclic stability. The optimized composite LMG-3 (90 wt% LiCl) exhibits a tenfold increase in water absorption capacity compared to MIL-101(Cr)@GO at P/P 0 = 0.3. The introduction of GO significantly increases the heat diffusion coefficient, and the material exhibits excellent cyclic stability and inhibits salt deliquescence, demonstrating its potential for adsorptive thermal storage applications.
研究领域:
材料科学
·
能源工程
✓ 已验证
产品关联
DOI
高影响因子
SCIENCE OF THE TOTAL ENVIRONMENT
·
2021
·
IF 7.963
Yawen Cai,Jinghua Feng,Xiaoli Tan,Xin Wang,Zhimin Lv,Weiwei Chen,Ming Fang,Haining Liu,Xiangke Wang
The efficient decontamination of pertechnetate ( 99 TcO 4 − ) is an essential task for managing radioactive 99 Tc in nuclear wastes . Perrhenate, (ReO 4 − ), as a nonradioactive analog, exhibits almost identical physicochemical properties as 99 TcO 4 − . Herein, a novel magnetic amine-functionalized MIL-101(Cr) (NH 2 -MIL-101(Cr)@Fe 3 O 4 ) was prepared and used to efficiently remove ReO 4 − from solution for the facile magnetic separation. A series of environmental parameters were considered to investigate the adsorption performance of NH 2 -MIL-101(Cr)@Fe 3 O 4 . Experimental results suggested that NH 2 -MIL-101(Cr)@Fe 3 O 4 has reached a satisfied adsorption capacity (~401 mg/g) and a very fast adsorption kinetics at pH 7.0. The selectivity for ReO 4 − was maintained even in the presence of interfering anions with relatively high concentrations. ReO 4 − were mainly captured by N-donor sites of the surface-decorated amine via complexation and were trapped in the cavities of modified MIL-101(Cr). NH 2 -MIL-101(Cr)@Fe 3 O 4 exhibits satisfactory adsorption performance for ReO 4 − and can be conveniently separated from wastewaters after adsorption.
研究领域:
环境科学
·
材料科学
·
放射化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2024
·
IF 4.9
Tien Tran Nguyen,Minh Kim Nguyen,Vipin Kumar,Ha Huu Do,Anh Thi Kim Le,Anh Van Nguyen,Jin Seog Gwag,Pham Cam Nam,Le Gia Trung
The widespread use and subsequent release of antibiotics by humans and animals pose health and environmental risks, compelling their removal from aquatic ecosystems. MIL-101(Cr), a metal-organic framework (MOF), exhibits versatile applications in antibiotic adsorption owing to its exceptional structural characteristics. In this context, MIL-101(Cr) nanoparticles are successfully prepared via the hydrothermal method to remove pefloxacin (PEF) from aqueous solutions. The resulting MIL-101(Cr) adsorbents showcase high crystallinity (97.6%), a large surface area (3166 m 2 /g), broad nanopore sizes, good thermal stability, and efficient reusability. Factors including initial PEF concentration, pH, dosage of adsorbent, and temperature are thoroughly investigated. The findings reveal a good adsorption capacity (254.3 mg/g) with an optimal removal efficiency (99.7%) at 308 K in a neutral pH of 7.0 when the adsorbent dosage is 250 mg/L and the initial PEF concentration is 200 mg/L within 80 min of contact. Among the three adsorption isotherms (Langmuir, Freundlich, Temkin models), the Langmuir equation best fits the studies, indicating a maximum adsorption capacity of 253.8 mg/g at 25°C, while the experimental equilibrium adsorption capacity is 229.2 mg/g at the same temperature. Adsorption kinetics aligns with the pseudo-second-order model. Thermodynamic parameters and activation energy affirm the endothermic and spontaneous behavior of the adsorption process, attributed to both physisorption and chemisorption. This study highlights the promising potential of synthesized MOF nanocrystals as an effective adsorbent for antibiotics in wastewater treatment and environmental remediation.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）