JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Qin-Chao Wang,Zhaoquan Peng,Sha He,Hao Chen,Jinglong Du,Huilin Zang,Xiaoge Li,Xiuqin Zhan,Jie Han
Sodium superionic conductor NaTi 2 (PO 4 ) 3 has attracted significant interest as an anode material for sodium-ion batteries (SIBs). However, its practical application is hindered by its low inherent electrical conductivity, particularly at low temperatures. In this study, oxygen vacancies (V O ) were introduced into NaTi 2 (PO 4 ) 3 nanoribbons to enhance sodium storage performance at low temperatures. X-ray diffraction with Rietveld refinement, electron paramagnetic resonance, and X-ray photoelectron spectroscopy confirm that NaTi 2 (PO 4 ) 3 -2 nanoribbons (NTP-2) exhibit the richest V O concentration. These V O , which bridge TiO 6 octahedra and PO 4 tetrahedra, significantly enhance the antibonding interactions of Ti1–O2 and P1–O1 bonds, while stabilizing the bonding in NaTi 2 (PO 4 ) 3 . The energy barrier for Na + migration is reduced to 0.40 eV involving the V O . The optimized NTP-2 anode demonstrates superior low-temperature performance, maintaining a capacity of 106.1 mAh g −1 (about 96.1 % of its initial capacity) at −20 °C after 300 cycles. Additionally, the NTP-2 anode exhibits a moderate Na + diffusion coefficient of 1.47 × 10 –11 cm 2 s −1 at −20 °C. Furthermore, the Na 3 V 2 (PO 4 ) 3 //NTP-2 full cell retains a capacity of 64 mAh g −1 at −20 °C after 250 cycles, highlighting its potential for low-temperature applications. By integrating oxygen vacancies and nanoengineering, both electronic and ionic conductivities are significantly enhanced in NaTi 2 (PO 4 ) 3 , positioning promising applications for SIBs in low-temperature environments.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ELECTROCHIMICA ACTA
·
2017
·
IF 4.798
Yanyan Kong,Jiaxiang Sun,Ligang Gai,Xiaojuan Ma,Jianhua Zhou
Aqueous rechargeable batteries (ARBs) based on migration of two types of shuttle ions not only enrich the battery families but also make it more available for ARBs with operation potential higher than 1.2 V. In this paper, we report on electrochemical properties of ARBs in configuration of NaTi 2 (PO 4 ) 3 /C||LiMn 2 O 4 , i.e. NTP/C||LMO. NTP/C was prepared through a simple and scalable co-precipitation post annealing treatment method and featured with hierarchical structure, high specific surface area, and abundant mesopores. The electrochemical properties of individual anode and cathode were examined in 1 mol L −1 Li 2 SO 4 , 1 mol L −1 Na 2 SO 4 , and 0.5 mol L −1 Li 2 SO 4 /0.5 mol L −1 Na 2 SO 4 mixed electrolyte, respectively. It is found that NTP/C exhibits superior operation in 1 mol L −1 Na 2 SO 4 and inferior operation in 1 mol L −1 Li 2 SO 4 while the situation is contrary for LMO. However, NTP/C||LMO full cells with Li + /Na + -mixed electrolyte exhibit enhanced electrochemical performance, presenting an anode-dependant electrochemical behavior. When operating at 1C, NTP/C||LMO with Li + /Na + -mixed electrolyte can deliver a discharge specific capacity ( C dis ) of 104.6 mA h g −1 based on the weight of NTP/C, and a specific energy ( E cell ) of 59.5 W h kg −1 with corresponding specific power of 76.8 W kg −1 based on the total weight of active electrode materials. After 220 cycles at 1C, the C dis and E cell remain 75.7 mA h g −1 and 43.0 W h kg −1 , respectively.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2018
·
IF 8.097
Peng Wei,Yanxiang Liu,Yarui Su,Ling Miao,Yangyang Huang,Yi Liu,Yuegang Qiu,Yuyu Li,Xiaoyu Zhang,Yue Xu,Xueping Sun,Chun Fang,Qing Li,Jiantao Han,Yunhui Huang
We are presenting a sol–gel method for building novel nanostructures made of nanosized F-doped Na1–2xTi2(PO4)3–xFx (NTP-Fx, x = 0, 0.02, 0.05, and 0.10) particles embedded in three-dimensional (3D) carbon matrices (NTP-Fx/C). This technique combines advantages of both zero-dimensional materials and 3D-carbon networks. Proper fluorine doping stabilizes the NTP structure and greatly enhances ion/electron transportation, leading to superhigh-rate electrochemical performance and ultralong cycle life. The composite electrode delivers high specific capacities of 121, 115, 112.2, 110.1, 107.7, 103.1, 85.8, and 62.5 mA h g–1 at 0.2, 0.5, 1, 2, 5, 10, 20, and 30 C, respectively. It retains an unbelievable ∼70% capacity after a thousand cycles at a rate as high as 10 C. Electroanalytical results reveal that fluorine doping significantly enhances Na+ diffusion kinetics. Meanwhile, density functional theory calculations demonstrate F-doped NTPs’ own outstanding electrochemical properties, which is due to the enhanced intrinsic ionic/electronic conductivity. The results show that anion doping is an efficient way to make high-performance NTP anodes for sodium-ion batteries.
研究领域:
电化学
·
材料科学
·
能源存储
·
纳米材料
·
固态化学
·
电化学储能
✓ 已验证
DOI
高影响因子
MATERIALS LETTERS
·
2018
·
IF 2.687
Xi Cao,Yang Yang
NASICON-structured NaTi 2 (PO 4 ) 3 is regarded as the most suitable anode for aqueous sodium ion batteries, however, the low electronic conductivity intrinsically restricts its application. NaTi 2 (PO 4 ) 3 -carbon composite is prepared by a facile solid state sintering method and studied as the anode in aqueous sodium ion battery , coupling with activated carbon as the cathode. This neutral sodium ion battery shows a high output voltage of 1.17 V, with outstanding rate and cycling stability. The full cell delivers an energy density of 33.4 Wh∙kg −1 at a power density of 33.4 W∙kg −1 based on the total active mass of the anode and cathode materials.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2015
·Vol. 3
·期 36
·18718-18726
·
IF 7.443
Gongzheng Yang,Huawei Song,Mingmei Wu,Chengxin Wang
Besides targeting low-voltage intercalation, NaTi2(PO4)3 (NTP) is a promising negative electrode material for non-aqueous sodium-ion batteries (SIBs). However, the low electronic conductivity of this material inhibits its potential applications. Herein, we report the controllable synthesis of four interesting porous NTP nanocubes via a one-pot solvothermal method. The as-synthesized products have shown excellent high-rate performance and cycling stability as SIB anodes. After 10 000 cycles at a 10C rate, 75.5% of the initial capacity is retained, which exceeds those of most of the reported SIB anode materials. Even at an extremely high rate of 100C, the NTP nanocubes can still deliver considerable reversible capacities after deep charging/discharging for 15 000 cycles. The superior electrochemical performances can be attributed to their unique nanostructures. We hope that such a finding of the new construction will enrich the NTP system and provide several possible candidates for SIB anodes.
研究领域:
材料科学
·
电化学
·
纳米材料
·
能源存储
·
电池技术
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2018
·Vol. 29
·期 11
·9258-9267
·
IF 2.324
Xu Liang,Xu Guobao,Chen Zhuo,Wei Xiaolin,Cao Juexian,Yang Liwen
NaTi 2 (PO 4 ) 3 (NTP) with NASICON structure has been regarded as a promising material for sodium-ion batteries (SIBs). However, NTP always exhibits poor cycling stability and rate performance due to slow electronic conductivity. In this work, a free-standing 3D nanocomposite constructed by reduced graphene oxide (rGO), thermally-treated protein (TP) and mesoporous NaTi 2 (PO 4 ) 3 nanocrystals (denoted as MNTP-TP@rGO) is reported. The fabrication includes an electrostatic self-assembly, freeze-drying, mechanical pressing and thermal treatment. In the MNTP-TP@rGO nanocomposite, 3D interconnected carbon network of rGO and TP acts as both a support for the anchored well-distributed MNTP nanocrystals and a current collector. When free-standing MNTP-TP@rGO is used directly as anode in coin-type half-cell, it delivers a high-rate capacity (52.8 mAhg −1 at 50C) and robust cycling stability with the capacity retention of 80% after 1000 cycles at 5C. Furthermore, a full Na-ion battery is constructed using Na 3 V 2 (PO 4 ) 3 /C (NVP/C) as a cathode and free-standing MNTP-TP@rGO as an anode and it exhibits a high specific capacity (58 mAhg −1 at 1C) and outstanding cycling stability (98% capacity retention over 100 cycles at 1C). Our results suggest great potential of the free-standing electrode of MNTP-TP@rGO composite in high-performance SIBs.
研究领域:
材料科学
·
能源存储技术
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2018
·
IF 8.097
Peng Wei,Yanxiang Liu,Zhihao Wang,Yangyang Huang,Yu Jin,Yi Liu,Shixiong Sun,Yuegang Qiu,Jian Peng,Yue Xu,Xueping Sun,Chun Fang,Jiantao Han,Yunhui Huang
NaTi2(PO4)3 (NTP) with a sodium superionic conductor three-dimensional (3D) framework is a promising anode material for sodium-ion batteries (SIBs) because of its suitable potential and stable structure. Although its 3D structure enables high Na-ion diffusivity, low electronic conductivity severely limits NTP’s practical application in SIBs. Herein, we report porous NTP/C nanofibers (NTP/C-NFs) obtained via an electrospinning method. The NTP/C-NFs exhibit a high reversible capacity (120 mA h g–1 at 0.2 C) and a long cycling stability (a capacity retention of ∼93% after 700 cycles at 2 C). Furthermore, sodium-ion full cells and hybrid sodium-ion capacitors have also been successfully assembled, both of which exhibit high-rate capabilities and remarkable cycling stabilities because of the high electronic/ionic conductivity and impressive structural stability of NTP/C-NFs. The results show that the nanoscale-tailored NTP/C-NFs could deliver new insights into the design of high-performing and highly stable anode materials for room-temperature SIBs.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ELECTROCHIMICA ACTA
·
2018
·
IF 5.116
Jing Zeng,Zulai Cao,Yang Yang,Yunhui Wang,Yueying Peng,Yiyong Zhang,Jing Wang,Jinbao Zhao
The commercial applications of rechargeable magnesium batteries (RMBs) are hindered by the slow diffusion kinetic of Mg 2+ ions in cathode materials. To overcome this problem, we design a new Na-Mg hybrid battery with the NaTi 2 (PO 4 ) 3 @Carbon (NTP@C) nanoparticles as a cathode material, the Mg metal as an anode and the Mg(TFSI) 2 + NaBH 4 - triglyme/1,2-Dimethoxyethane (DME) as a hybrid electrolyte. For the first time, the Mg(TFSI) 2 is applied as a Mg 2+ ions source in the chlorine-free Na-Mg hybrid electrolyte with NaBH 4 as both Na + ions source and moisture scavenger. The NTP@C/Mg hybrid battery shows excellent electrochemical performance. The corresponding average capacity decay after 1000 cycles is only 0.004% and 0.008% per cycle at 2 C and 10 C, respectively. Even at 20 C, about 60 mAh g −1 can be obtained after 26000 cycles. The impressive capacity retention of 93.7% and 90.2% can be obtained at 5 and 10 C, respectively. The excellent electrochemical performance of the hybrid battery confirms the feasibility using Mg(TFSI) 2 in the chlorine-free hybrid electrolyte for long term cycle. The developed NTP@C/Mg hybrid battery possesses the advantages of excellent electrochemical performances, good safety and low cost, making it promising for the commercial applications, especially for the large-scale energy storages.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
SOLID STATE IONICS
·
2018
·
IF 2.751
Zhen Jiang,Lu Liu,Yuehua Li,Jing Zhu,Chuanchang Li,Zhangxing He,Wei Meng,Yingqiao Jiang,Lei Dai,Ling Wang
NaTi 2 (PO 4 ) 3 /C (NC) composites decorated by carbon nanotubes (CNTs) were prepared via a sol-gel way, and employed as anode in aqueous lithium ion batteries . An effective conductive network was obtained by decoration of CNTs, which can interconnect NC particles. CNTs decoration has no obvious effect on lattice structure for NaTi 2 (PO 4 ) 3 , and can enhance electrochemical properties for NC. Moreover, NC decorated by CNTs with optimal content of 8.8% (NC-CNTs-10) exhibits the highest electrochemical properties. NC-CNTs-10 delivers the discharge capacity of 96.4, 93.7, and 74.2 mAh g −1 at 0.5, 3, and 15C, respectively, with increase of 2.7, 15.1, and 38.2 mAh g −1 compared with NC. In addition, NC-CNTs-10 shows excellent cycling performance. Capacity retention for NC-CNTs-10 can reach 91.2% after 1000 cycles at a rate of 4C, 16.7% larger than that of pristine NC. Our study reveals that CNTs decoration is a simple way to raise electrochemical properties for NaTi 2 (PO 4 ) 3 /C in aqueous lithium ion batteries .
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2018
·
IF 3.779
Zhi Zhou,Simin Gu,Yongli Zhang,Fangfang Wu,Nan Zhou
NASICON-type NaTi 2 (PO 4 ) 3 has been acknowledged as a promising anode for energy storage due to high ion conductivity and low cost. Nevertheless, intrinsic low electrical conductivity of NaTi 2 (PO 4 ) 3 and low stability in aqueous electrolyte limit its further applications in aqueous lithium rechargeable battery. In this paper, polyaniline as carbon and nitrogen sources was employed to synthesize nitrogen-doped carbon coated NaTi 2 (PO 4 ) 3 (NTP-P) composite by sol-gel approach and following calcination treatment. The loose and carbon-coated structure endows NTP-P with good structure stability and improved electrochemical kinetics . Compared with glucose-derived carbon-coated NaTi 2 (PO 4 ) 3 composite, NTP-P exhibits superior rate and cycling performance. NTP-P with proper carbon content delivers the discharge capacity of 119.4 and 83.4 mAh g −1 at rate of 0.2 and 15 C, and its capacity retention can maintain 85.8% after 1000 cycles at 5 C. This research reveals that the integration of carbon coating and nitrogen doping by using polyaniline give an excellent method to enhance the electrochemical properties of electrode materials.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机非金属材料
·
功能材料
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2021
·
IF 4.158
Bin Li,Boxuan Jin,Ruochen Zhang,Kaixuan Ma,Xianwen Wu,Lei Dai,Ling Wang,Zhangxing He
Metal zinc is used as anode in aqueous zinc-ion batteries due to its environmental protection, abundant storage, and high theoretical capacity. However, zinc anode has many challenges such as side reactions and zinc dendrites, which impede the further development of aqueous zinc-ion batteries. A facile strategy of constructing Sn doped NaTi 2 (PO 4 ) 3 (NTP/Sn) protective layer on surface of zinc anode (Zn@NTP/Sn) was adopted to enhance the cycling stability of zinc anode in this work. Sn doped NaTi 2 (PO 4 ) 3 was used to realize high-performance zinc anode via the structure design and interfacial characteristics, which are beneficial to accelerating transfer of Zn 2+ and improving interface performance. The average voltage hysteresis of Zn@NTP/Sn symmetric cell is only 17.4 mV at the current density of 0.4 mA cm −2 , which is much lower than that of bare Zn (75.8 mV) and Zn@NTP (43.7 mV) symmetric cells. Furthermore, Zn-MnO 2 full cell using Zn@NTP/Sn anode also shows good cycling performance. After 500 cycles at a current density of 1.2 A g −1 , Zn@NTP/Sn-MnO 2 full cell has the highest capacity of 124.2 mAh g −1 . While the bare Zn-MnO 2 and Zn@NTP-MnO 2 full cells only have 39.3 mAh g −1 and 74.2 mAh g −1 . The excellent electrochemical performance is related to improvement of wettability , increase of cell volume, and reduction of side reactions. In general, this work realizes a synergistic strategy combining structural design and interfacial modification by doping Sn for NTP as a protective coating layer for zinc anode, which provides a simple strategy for high-performance rechargeable aqueous zinc-ion batteries.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
SOLID STATE IONICS
·
2017
·
IF 2.354
Xujiao Yang,Kaiying Wang,Xianli Wang,Guangli Chang,Siao Sun
NASICON-type NaTi 2 (PO 4 ) 3 material has been extensively studied as a promising anode for sodium-ion batteries due to the open 3D framework with the large interstitial spaces, high theoretical capacity and small volume change during cycling process. However, the practical application of NaTi 2 (PO 4 ) 3 is hampered because of its low electronic conductivity . Herein, a simple approach along with post-annealing has been designed and adopted to prepare the carbon-coated NaTi 2 (PO 4 ) 3 (NaTi 2 (PO 4 ) 3 @C) composite. The as-prepared anode material is characterized by XRD , SEM, TEM and Raman spectrum . The electrochemical measurements reveal that NaTi 2 (PO 4 ) 3 @C has excellent Na-storage performances including high reversible capacity (112.6 mAh g − 1 at 0.2 C) and good rate capability (87.1 mAh g − 1 at 5 C). The superior electrochemical performance can be resulted from the synergistic effects of the nanosized NaTi 2 (PO 4 ) 3 particles and conductive carbon layer .
研究领域:
材料科学
·
电化学
·
储能
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）