WATER AIR AND SOIL POLLUTION
·
2024
·Vol. 235
·期 10
·1-15
·
IF 3.8
Liu Xu,Kong Xiaomin,Wen Hao,Wang Yue,Wu Meili,Yin Hongwei,Qin Wei,Wang Manli,Pei Jun,Qu Miaoming
Coal gangue, a byproduct of coal mining with massive generation, presents a major challenge for resource utilization. In this study, SiO 2 aerogel was successfully fabricated from coal gangue, via a facile and cost-effective approach. The aerogel boasts an intricate network framework structure internally and functions as a mesoporous material with measurements of 154.5662 m 2 ·g −1 for specific surface area and 7.9557 nm for average pore size. Additionally, exploring the adsorption capabilities of SiO 2 aerogel concerning Pb(II) in wastewater, the research revealed insights. The results demonstrated that the maximum Pb(II) removal efficiency reached 94.09% under pH 6, aerogel dosage of 1.5 g·L⁻ 1 , and initial Pb(II) concentration of 80 mg·L⁻ 1 . The adsorption process followed the Langmuir isotherm model and pseudo-second-order kinetic model, suggesting a favorable and predominantly monomolecular layer chemisorption, and the intraparticle diffusion model suggests internal diffusion behavior during adsorption. The SiO 2 aerogel exhibited specific adsorption behavior towards Pb(II). This study offers a promising avenue for repurposing coal gangue while addressing the issue of Pb(II)-contaminated wastewater.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2017
·
IF 3.359
Yan He,Qinqin Liu,Jun Hu,Chengxi Zhao,Changjun Peng,Qiang Yang,Hualin Wang,Honglai Liu
Porous organic polymers (POPs), a new class of porous materials constructed by organic molecular building blocks, have attracted much attention. To design POPs with both good porosity and specific-task functionalization is still a critical challenge. In this work, using a simple Friedel-Crafts one-step reaction, one of the most common organic compound methylbenzene monomers were polymerized through the cross-linker formaldehyde dimethyl acetal (FDA) to produce a cost-effective non-functionalized porous polymer (POP-CH 3 ). Moreover, amine groups were further incorporated into the network by the post-synthetic modification method. The resulted porous polymer POP-NH 2 presented highly effective in removing Pb(II) from aqueous solution. The maximum Pb(II) adsorption capacity, q max , evaluated from the Langmuir model was 523.6 mg g −1 . The combination of FT-IR experimental results and the theoretical quantum calculations illustrated that the amine groups ( NH 2 ) can easily form coordination complexes with Pb(II), which were responsible for efficient adsorption. The generated POP-NH 2 could be regenerated effectively and recycled at least four times without significant loss of adsorption efficiency. Hence, the outstanding Pb(II) adsorption capacity, excellent reusability as well as low cost of synthesis create potential polymer POP-NH 2 to be an attractive adsorbent for removing toxic metal ions from aqueous solution.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
Applied Sciences-Basel
·
2020
·Vol. 10
·期 3
·948
·
IF 2.474
Yu Tao,Chuan Zhang,Ting Lü,Hongting Zhao
A class of polyethyleneimine (PEI)-functionalized Fe3O4magnetic nanoparticles (MNPs) has been facilely produced through a solvothermal process. The synthetic MNPs have been characterized by multiple technologies and then used for Pb(II) ion sorption from the aqueous media in different conditions. It was found the Pb(II) adsorption behaviors could be well fitted by the pseudo second-order kinetic and Langmuir isotherm models. The maximum Pb(II) adsorption capacity at 25 °C and pH 5.0 was calculated to be 60.98 mg/g. Moreover, effects of temperature, pH, and electrolyte of aqueous phase on the Pb(II) adsorption capacity of MNPs have been carefully examined. The Pb(II) adsorbing capacity was enhanced with temperature or pH rising, but reduced with the addition of various electrolytes. Additionally, the recyclability of synthetic MNPs has been also assessed. The prepared PEI-functionalized MNPs could still maintain good adsorption performance after five cycles of Pb(II) removal. These results indicated that the PEI-functionalized Fe3O4MNPs could be readily synthesized and served as a desirable and economic adsorbent in Pb(II)-contaminated wastewater treatment.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY
·
2019
·
IF 4.978
Jiling Zhao,Chen Wang,Shixing Wang,Yang Zhou
A new adsorbent (MOFs-DHAQ) was prepared by functionalizing UiO-66-NH 2 with 1,8-dihydroxyanthraquinone to remove Pb(II) from wastewater. The optimum pH, adsorption kinetics and adsorption isotherms were studied. MOFs-DHAQ has a good removal rate for Pb(III) at pH 4. It takes only 30 min to reach maximum adsorption capacity about 213.3 mg/g. The experimental data conforms to the pseudo-secondary kinetics and the Freundlich models. The adsorption process belongs to multilayer chemical adsorption . Desorption and adsorption experiments indicate that the adsorbent can be recycled at least four times. The rising temperature favors the adsorption of Pb(II) on MOFs-DHAQ because the adsorption process is a spontaneous endothermic reaction. The interaction mechanism between Pb(II) and the reactive group is mainly electrostatic interaction and complexation. MOFs-DHAQ has excellent selectivity for removing Pb(II) from wastewater contains a variety of interfering ions. The calculated adsorption capacity ( Q ex ) of Pb(II) for column adsorption was 108.04 mg/g and was consistent with the Thomas model's adsorption capacity( Q Th ) about 109.63mg/g. Density functional theory calculations show that MOFs-DHAQ combines with Pb(II) through monodentate N atoms and bidentate O groups. MOFs-DHAQ has good application prospect in the removal of lead from wastewater.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2016
·
IF 4.836
Chunzhen Fan,Kan Li,Juexiu Li,Diwen Ying,Yalin Wang,Jinping Jia
In this paper, tetraethylenepentamine (TEPA) modified chitosan/CoFe 2 O 4 particles were prepared for comparative and competitive adsorption of Cu(II) and Pb(II) in single and bi-component aqueous solutions. The characteristics results of SEM, FTIR and XRD indicated that the adsorbent was successfully fabricated. The magnetic property results manifested that the particles with saturation magnetization value of 63.83 emu g −1 would have a fast magnetic response. The effects of experimental parameters including contact time, pH value, initial metal ions concentration and coexisting ions on single and bi-component adsorption were investigated. The results revealed that the adsorption kinetic was followed pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-limiting step. Sorption isotherms were also determined in single and bi-component solutions with different mass ratio of Cu(II) to Pb(II) (Cu(II)/Pb(II)) and fitted using Langmuir and Freundlich isotherm models. A better fit for Cu(II) and Pb(II) adsorption were obtained with Langmuir model, with a maximum sorption capacity of 168.067 and 228.311 mg g −1 for Cu(II) and Pb(II) in single component solution, 139.860 and 160.256 mg g −1 in bi-component solution (Cu(II)/Pb(II) = 1:1), respectively. The present results suggest that TEPA modified chitosan/CoFe 2 O 4 particles are feasible and satisfactory adsorbent for efficient removal of Cu(II) and Pb(II) ions.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
ADVANCED POWDER TECHNOLOGY
·
2019
·
IF 3.25
Yuting Chu,Muhammad Asim Khan,Fengyun Wang,Mingzhu Xia,Wu Lei,Sidi Zhu
Arg-Mt, was fabricated by modifying sodium montmorillonite (Na-Mt) with Arginine monohydrochloride (Arg salt), to adsorb Pb(II) and Cu(II) in aqueous solution. The X-ray powder diffraction (XRD), Fourier transform infrared (FTIR) spectrum, thermal analysis (TG/DTG), Brunauer-Emmett-Teller (BET) and Scanning electron microscope (SEM) were employed to investigate the properties of Na-Mt and Arg-Mt. The effects of the amount of modifier, pH value, the initial concentration of M(II), temperature and contact time were tested in a single adsorption system. The isotherm model was well matched with the Langmuir curve and the kinetic adsorption fitted well with the pseudo-second-order rate equation. The saturated adsorption of Pb(II) and Cu(II) by Arg-Mt were 124.69 and 29.15 mg/g, respectively, which were higher than that of Na-Mt (89.08 and 23.93 mg/g). The thermodynamic equation indicated that the adsorption process was spontaneous, endothermic, and the randomness of the samples changed a little after adsorption. The adsorption capacity of heavy metal ions in the binary co-adsorption system was poor than single adsorption system. Furthermore, the adsorbed M(II) onto Arg-Mt can hardly be dissolved under weak acidic condition (pH > 4) according to the desorption experiments. High-efficiency and low-cost make Arg-Mt to be used in the removal of heavy ions in aqueous solution.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2019
·
IF 4.784
Xue Xue Liang,Xiao-Kun Ouyang,Songyan Wang,Li-Ye Yang,Fangfang Huang,Chao Ji,Xiaohong Chen
The performance of Fe 3 O 4 /attapulgite (APT) nanoparticles in Pb(II) adsorption from aqueous solutions could be improved by modifying the particles with aminopropyltriethoxysilane (APTS) and then combining with chitosan (CS) into beads. After preparing the APTS-Fe 3 O 4 /APT@CS beads, their surface morphology and crystal phases were analyzed by Fourier-transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction. The magnetic properties of APTS-Fe 3 O 4 /APT@CS were studied by a vibrating sample magnetometer, while their heat resistance and stability were characterized by thermal weight analysis. A recycling test and comparison of adsorption capacities were also carried out. The adsorption capacity of Fe 3 O 4 /APT was improved by the modification with APTS and CS. The adsorption process conforms to the pseudo-second-order kinetic and Langmuir adsorption isotherm models. The adsorption of Pb(II) reaches a maximum of 625.34 mg/g, which compares favorably with other reported adsorbents. The results show that APTS-Fe 3 O 4 /APT@CS is a promising hybrid adsorbent for effective removal of Pb(II) from water.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2022
·Vol. 46
·期 23
·11158-11165
·
IF 3.925
Jipeng Li,Yanzhi Sun,Yongmei Chen,Yang Tang,Junqing Pan,Pingyu Wan
In the present study, the preparation of a new MOF material His-MIL-53(Al) and its performance in the adsorption of Pb(II) from aqueous solution were investigated. The original material MIL-53(Al) was directly grafted with histidine to obtain the modified MOF material His-MIL-53(Al). The results show that His-MIL-53(Al) has excellent adsorption performance for Pb(II), and the adsorption process is in accordance with the pseudo first-order kinetics and the Langmuir adsorption model, with a maximum adsorption capacity of 50.13 mg g−1, which is much larger than the adsorption capacity of the original material MIL-53(Al). The experimental results also show that the prepared material has good recoverability. Our work demonstrates the applications of His-MIL-53(Al) as a promising material in the adsorption of heavy metals.
研究领域:
环境科学
·
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2025
·
IF 9
Wenya Shi,Jie Yang,Yuyang Guo,Zhaoyu Zhang,Hualin Li,Han Guo,Jianqiu Deng,Qingrong Yao,Lichun Cheng,Qianxin Long
Industrial wastewater containing heavy metal ions has become an urgent problem to be solved due to its environmental persistence and bioaccumulation. In this study, powdered adsorbent (DE/CBC) and spherical adsorbent (SA@DE/CBC) were prepared from natural diatomite (DE), crab shell biochar (CBC) and sodium alginate (SA) as raw materials, and were used to adsorb Pb(II) from wastewater. The adsorption isotherm fitting showed that the experimental process of DE/CBC and SA@DE/CBC conformed to the Langmuir model, and the maximum adsorption capacity of the monolayer reached 1155 mg/g and 365 mg/g, respectively. The pseudo-first-order kinetic model showed better fitting for the two adsorbents, and the diffusion rate was controlled by multiple steps. Compared with most traditional composite adsorbents, DE/CBC and SA@DE/CBC can achieve 98 % and 93 % adsorption rates at relatively high Pb(II) concentrations, and maintain 83 % and 84 % high adsorption capacity after 10 adsorption–desorption cycles, demonstrating superior Pb(II) adsorption performance and excellent structural stability. The spherical morphology not only effectively solves the problems of adsorbent recovery and secondary pollution prevention and control, but also plays a role in protecting the structure and active sites of powdery materials, making it more durable and practical. Collectively, the developed composite not only enables high-value-added utilization of biowaste but also demonstrates cost-effectiveness and excellent reusability, providing a sustainable remediation strategy for lead-contaminated water systems.
研究领域:
环境科学
·
材料工程
·
化学工程
·
水处理技术
·
吸附过程
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）