文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

346,364+ SCI 论文 与阿拉丁产品引用相关
2,295,288.15 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

热门产品

视图 列表 网格

显示第1至12个,产品总数351个

设置提升方向
Ta
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY · 2025 · IF 6.2

Ablation behavior of C/C composites matrix-modified by solid solution ceramic (Ta,Zr)C-SiC with different Zr/Ta ratios

Yuanming Zhou,Shuxin Li,Shuangxing Zhu,Ruizhi Liu,Zhenxiao Tang,Maozhong Yi,Ke Peng

To investigate the influence of (Ta,Zr)C on the ablation resistance of C/C composites, C/C-(Ta 0.5 Zr 0.5 )C-SiC, C/C-(Ta 0.33 Zr 0.67 )C-SiC, and C/C-(Ta 0.2 Zr 0.8 )C-SiC were prepared with different Zr/Ta ratios through high-solid-loading slurry impregnation combined with precursor infiltration and pyrolysis. The flexural performance and ablation resistance both improved with an increasing Zr/Ta ratio. Compared to C/C-(Ta 0.5 Zr 0.5 )C-SiC and C/C-(Ta 0.33 Zr 0.67 )C-SiC, the flexural strength of C/C-(Ta 0.2 Zr 0.8 )C-SiC increased by 74.17 % and 24.29 %, respectively. The mass ablation rate was reduced by 74.33 % and 81.02 %, while the linear ablation rate was reduced by 98.60 % and 97.65 % after 120 s of ablation, respectively. The variations in Zr/Ta ratios affected the formation, integrity, and performance of the microstructure, which was composed of a Zr-rich oxide skeleton combined with Ta-rich oxide binder within the Ta-Zr-O oxide layer on the composite surface, ultimately enhancing the overall ablation resistance of these composites.

CAS / MDL: 25322-68-3
研究领域: 材料科学 · 航空航天工程
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CORROSION SCIENCE · 2025 · IF 8.5

Ablation response behavior and mechanism of (Hf, Ta)B2-(Hf, Ta)C-SiC ultra-high temperature multi-phase ceramics

Huan Guo,Bingzhu Wang,Ruifeng Li,Cheng Su,Jixiang Dai,Yong She,Yongzhong Zhao,Jianjun Sha

Aiming at forming a stable ablation layer for hafnium-based ultrahigh-temperature ceramics under ablation environment, in this work, the Ta-based ceramic was introduced into the Hf-based ceramic, and the effect of Hf/Ta molar ratios on the ablation response behavior and mechanism of (Hf, Ta)B 2 -(Hf, Ta)C-SiC ceramics was investigated. It was found that the introduction of Ta could form a continuous and dense ablation layer. When Hf/Ta= 0.9:0.1, the ceramic composite presented excellent ablation resistance, and the linear ablation rate was −0.083 μm/s, which was only 5.85 % of that of Hf-based ceramics (HfB 2 -HfC-SiC). The excellent ablation resistance attributed to that the ablation products (Ta 2 O 5 and Hf 6 Ta 2 O 17 ) could strongly bonded to the substrate, which was conducive to enhance the stability of the ablation layer.

CAS / MDL: 7440-44-0 64365-11-3
研究领域: 材料科学 · 航空航天工程
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
RSC Advances · 2017 ·Vol. 7 ·期 84 ·53111-53116 · IF 3.108

Electronic structure and properties of RbTiOPO4:Ta crystals

Ziqing Li,Yang Chen,Pengfei Zhu,Nianjing Ji,Xiulan Duan,Huaidong Jiang

RTP crystals doped with four different Ta concentrations were grown by high-temperature solution method. Ta dopants changed the growth habit of RTP and the (100) faces were more developed than the other crystal faces. The chemical composition and electronic structure were analyzed using Electron Probe Microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS). Ta elements could easily incorporate into RTP crystals from the melt due to the large distribution coefficient. As Ta content increased, the Rb 3d, Ti 2p, P 2p, O 1s XPS spectra showed a shift towards higher binding energy. The relative Ta atomic concentration in RTP:Ta crystals was calculated and it was determined that the molar ratio between Ta and Ti was higher than the nominal ratio. The thermal properties and SHG efficiency were also studied. Ta dopants decreased the transition temperature from the orthorhombic RTP phase to the cubic RTP phase and increased the decomposition temperature of the cubic RTP phase. When the Ta concentration increased to 9 mol%, the specific heat of the doped crystal was 1.5 times that of pure RTP crystal at 300 °C and SHG intensity was improved by 59% when compared with pure RTP. The results show that Ta doping is helpful for improvement of SHG efficiency and increasing resistance to laser irradiation.

CAS / MDL: 1314-61-0
研究领域: 材料科学 · 晶体学 · 光学
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
COLLOIDS AND SURFACES B-BIOINTERFACES · 2022 · IF 5.999

Preparation of PAA/PAM/MXene/TA hydrogel with antioxidant, healable ability as strain sensor

Miao Qin,Wenfeng Yuan,Xiumei Zhang,Yizhu Cheng,Mengjie Xu,Yan Wei,Weiyi Chen,Di Huang

Conductive hydrogels based on MXene have gained more attention due to the excellent conductive property and biocompatibility. At present, they have great potential in electronic skins, personally healthcare monitoring and human motion sensing. However, MXene are prone to be oxidized due to the abundant hydroxyls , which results in the unstable conductive property of hydrogel. To improve the shortcoming, conductive PAA/PAM/MXene/TA hydrogel was prepared, in which the introduction of TA can prevent MXene from oxidation owing to the great deal of pyrogallol groups. Mechanical tests showed that the tensile strength , toughness and elongation at break of PAA/PAM/MXene/TA hydrogel are 0.251 ± 0.05 MPa, 0.895 ± 0.16 MJ/m 3 and 560.82 ± 19.56%, respectively, indicating the hydrogel possess good stretchability. In addition, the MXene and TA were introduced into hydrogel through hydrogen bonds , which endow the hydrogel with good restorability and self-healing property. Resistance variation-strain curves demonstrated that the introduction of MXene endue the hydrogel with appreciable sensing performances. Moreover, in vitro cytotoxicity assay indicated that the hydrogel has good biocompatibility. In conclusion, PAA/PAM/MXene/TA hydrogel has great potential in flexible wearable sensor field.

研究领域: 材料科学 · 纳米技术 · 生物医学工程 · 传感器
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
ELECTROCHEMISTRY · 2022 ·Vol. 90 ·期 2 ·027006-027006 · IF 1.777

Electrodeposition of Zn–Ta Coating from DMI–ZnCl2–TaCl5 Solvate Ionic Liquids

Aimin LIU,Mengxia GUO,Yubao LIU,Fengguo LIU,Xianwei HU,Zhongning SHI

In this work, the Zn–Ta coating was electrodeposited from DMI–ZnCl2–TaCl5 solvate ionic liquid. The electrochemical reaction was studied by cyclic voltammetry using titanium as working electrode. The onset potential of zinc and tantalum co-deposition was −0.7 V (vs. Ag). Moreover, potentiostatic electrodeposition experiments were conducted to investigate the influence of potential and temperature on the morphology of the coating. X-ray photoelectron spectroscopy analysis confirmed that the coating obtained by electrodeposition at −1.6 V (vs. Ag) and 353 K was composed of Zn, Ta, ZnO, and Ta2O5. The mass fraction of element tantalum was 6.21 %, and metallic tantalum accounted for 11.54 % of the mass of element tantalum. The corrosion current density of the Zn–Ta coating was 1.83 × 10−4 A cm−2.

研究领域: 材料科学 · 电化学
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
JOURNAL OF CRYSTAL GROWTH · 2018 · IF 1.742

Top-seeded solution growth and morphology change of RbTiOPO4:Ta single crystal

Ziqing Li,Yang Chen,Pengfei Zhu,Nianjing Ji,Xiulan Duan,Huaidong Jiang

The RbTiOPO 4 :Ta single crystal with dimensions of 4 mm × 31 mm × 18 mm was successfully grown by Top Seeded Solution Growth Technique. It is concluded that the doping Ta element can strongly influence the growth and morphology of the RbTiOPO 4 crystal. The evident morphology change of RbTiOPO 4 :Ta crystal with respect to RbTiOPO 4 crystal has been observed and the (1 0 0) crystal face was more developed than any other crystal faces. The possible reasons of the morphology change were analyzed through experimental and theoretical methods. Several methods were tried to increase crystallographic a direction dimension of RbTiOPO 4 :Ta crystals. Finally, the RbTiOPO 4 :Ta single crystal with crystallographic a direction dimension up to 6 mm was obtained by using thicker seed crystal. This way makes it possible to get isometric RbTiOPO 4 :Ta crystals, which is beneficial for nonlinear optical applications due to larger area in x-y plane.

CAS / MDL: 1314-61-0
研究领域: 材料科学 · 晶体学
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
SOLID STATE SCIENCES · 2024 · IF 3.4

Enhanced optical, dielectric, and non-Ohmic properties in Ta-doped Bi2/3Cu3Ti4O12 ceramics

Renzhong Xue,Liuyang Zhao,Xiaosong Liu,Haiyan Wang,Xiang Zhu,Yifan Xiao,Chunyu Yuan,Binbin Cao,Ziyang Chen,Tao Li,Haiyang Dai

In this paper, Ta-doped Bi 2/3 Cu 3 Ti 4 O 12 (BCTO) ceramics are prepared by solid-state method. Phase structure, microstructure, optical, dielectric, and non-Ohmic properties of all samples are systematically investigated. Cu/Ta-rich phases at grain boundaries (GB) together with defects affect the microstructure, causing grain size and compactness to increase first and then decrease. Moreover, Ta doping increases the optical band gap of BCTO from 4.03 to 4.25 eV as well as the GB activation energy and GB barrier. An increase in dielectric constant (Ɛ r ), nonlinear coefficient (α) and breakdown field (E b ), and a decrease in the dielectric loss (tanδ) are observed in Ta-doped BCTO ceramics. The improvement in dielectric and non-Ohmic properties can be attributed to the internal barrier layer caused by GB Schottky barrier structure. In particular, Bi 2/3 Cu 3 Ti 3.95 Ta 0.05 O 12 ceramic exhibits the high Ɛ r of ∼45997 and the low tanδ of ∼0.035 at 10 kHz along with α of ∼5.62, and E b of ∼3.45 kV/cm. The temperature-independent (-110-210 °C) dielectric response confirms that temperature stability of specimens increases with doping. These results suggest that improved optical, dielectric, and non-Ohmic properties in Bi 2/3 Cu 3 Ti 4 O 12 can be achieved simultaneously via defect engineering.

研究领域: 材料科学 · 电子工程
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
ChemistrySelect · 2025 ·Vol. 10 ·期 15 ·e202405960 · IF 2

Ta/Organo-In Nanomaterials for Low-Power or Room Temperature Triethylamine Response

Xiaoyan Xiong,Yunpeng Gong,Yue Hu,Xu Ma,Hangzhou Wang,Cunzhi Li,Jianrong Ren,Chenguang Kong,Youcheng Huang,Shumin Jiang,Yufang Chen,Tao Jin

Graphical A nanoscale hollow tubular-structured Ta/Organo-In composite was synthesized. The material exhibited a response value of 92.34 to 50 ppm triethylamine at 190 °C, along with superior comprehensive performance in stability, sensitivity, and selectivity. Remarkably, it demonstrated detectable responses even at room temperature. The development of chemical sensor technology has been significantly advanced amine-responsive materials with the characteristics of rapid response, stability, and low-power consumption. This study synthesize Organo-In materials, and further explored the composite formation between tantalum (Ta) powder, and the organometallic indium (Organo-In). The morphology and structure of the resulting material were characterized using SEM, TEM, XRD, HAADF, and XPS. Results demonstrate the Ta/Organo-In composite's exceptional triethylamine (TEA) selectivity: Showing 92.34 response to 50 ppm TEA at 190 °C with 9s/486 s response/recovery times, outperforming aldehydes/ketones/aromatics. Notably, the Ta/Organo-In prepared by the method in this study showed a response value of approximately 3.4 toward 50 ppm TEA at room temperature (about 25 °C), and the response values remained stable after 10 consecutive cycles, indicating the material's excellent reliability and potential for low-power applications in real-time TEA monitoring devices at room temperature. The selectivity and continuous gas sensing performance of Ta/Organo-In at room temperature are both acceptable. Furthermore, within the concentration range of 1–500 ppm, the response values of the Ta/Organo-In material to TEA followed a Logistic curve fitting with an R 2 of 0.99644. Finally, the selective response mechanism of materials to TEA was discussed.

研究领域: 材料科学 · 化学传感器技术
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CERAMICS INTERNATIONAL · 2024 · IF 5.1

Enhanced densification and mechanical properties of Ta-Hf-C solid solution ceramics by WC doping

Wanhong Yu,Guifang Li,Changwan Sun,Jianquan Zhang,Li Yang,Yichun Zhou

In this paper, we propose an effective method for doping WC into Ta-Hf-C ceramics to significantly enhance their densification and mechanical properties. An increasing WC doping amount from 0 to 20 at.%, enhances the densification of Ta-Hf-C ceramics from 92.4 % to 99.1 %. This is mainly due to the fact that the doping of WC effectively removes the harmful oxygen impurities from the ceramics, thereby increasing their sintering activity. Furthermore, the doping of WC plays an active role in the mechanical properties of the ceramics. The Ta-Hf-C doped with 15 at.% WC has the highest value of 36.41 GPa for nano-hardness due to the solid solution strengthening mechanism, while the highest Vickers hardness (38.75 GPa) and fracture toughness (3.76 MPa m 1/2 ) appear in Ta-Hf-C doped with 20 at.% WC. The main toughness mechanism is W segregation at the grain boundary, enhancing grain boundary strength .

CAS / MDL: 12069-85-1 12070-06-3
研究领域: 材料科学 · 力学
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
RSC Advances · 2023 ·Vol. 13 ·期 8 ·5208-5218 · IF 3.9

One-step hydrothermal preparation of Ta-doped ZnO nanorods for improving decolorization efficiency under visible light

Thi Viet Ha Luu,Ngoc Nhiem Dao,Hoang Ai Le Pham,Quang Bac Nguyen,Van Cuong Nguyen,Phuc Huu Dang

In this work, Ta-doped ZnO (Ta-ZnO) nanomaterials were synthesized by the hydrothermal method at different temperatures (110, 150, and 170 °C) for the photodegradation of methylene blue (MB) under visible light. Ta doping significantly affects the crystal defects, optical properties, and MB photocatalytic efficiency of ZnO materials. The optical absorption edge of Ta-ZnO 150 was redshifted compared to undoped ZnO, correlating to bandgap narrowing (EgTa–ZnO = 2.92 eV; EgZnO = 3.07 eV), implying that Ta doped ZnO is capable of absorbing visible light. Besides, Ta-doping was the reason for enhanced blue light emission in the photoluminescence spectrum, which is related to the oxygen defect V0O. It is also observed in the XPS spectra, where the percentage of oxygen in the oxygen-deficient regions (O531.5 eV) of Ta-ZnO150 is higher than that of ZnO150. It is an important factor in enhancing ZnO's photocatalytic efficiency. The MB degradation efficiency of Ta-doped ZnO reached the highest for Ta-ZnO 150 and was 2.5 times higher than ZnO under a halogen lamp (HL). Notably, the influence of hydrothermal temperature on the structural, morphological, and photoelectrochemical properties was discussed in detail. As a result, the optimal hydrothermal temperature for synthesizing the nanorod is 150 °C. Furthermore, photocatalytic experiments were also performed under simulated sunlight and natural sunlight. The nature of the photo-oxidative degradation of MB was also investigated.

研究领域: 材料科学 · 环境科学
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2025 · IF 13.2

Multifunctional flexible MXene/TA@CNC electronic hydrogel patch with robust adhesion and self-healing properties for wearable electronics

Haoyu Wang,Ping Han,Ying Yu,Shaolong Han,Yue Qiao,Yuehan Li,Bin Sun,Zheng Gu

Conductive hydrogels have been extensively investigated and demonstrate promising applications in wearable and flexible sensors. However, their broader implementation in this field is hindered by the insufficient strain sensitivity, susceptibility to mechanical damage with limited self-recovery, and inadequate adhesion to human skin. Herein, we present a multifunctional MXene/TA@CNC electronic hydrogel patch (MTC e-patch) by integrating highly conductive two-dimensional (2D) transition metal carbides (MXene) and tannic acid-coated carboxylated cellulose nanocrystals (TA@CNC) with polyvinyl alcohol and borax. And dynamic three-dimensional (3D) network is formed through synergistic dynamic hydrogen bonding and dynamic borate ester linkages. The incorporation of TA@CNC effectively prevents the oxidation of MXene, thereby extending the operational lifespan of hydrogels. The flexible covalent crosslinked network, combined with the rigidity of TA@CNC, imparts the MTC e-patch with excellent electrical conductivity (1.62 S/m), superior mechanical strength (≈1.35 MPa, 930 %), robust adhesiveness (≈28 kPa), and high self-healing capability (92 %). The rapid (161 ms) and sensitive (Gauge factor = 4.39) sensing performance of the developed wearable sensor enables the precise detection of subtle human motions, such as swallowing, throat vibrations during speech, and pen strokes during writing. Even when damaged, the sensor continues to provide stable signal output, demonstrating significant potential for applications in smart wearables, electronic skins, and human–machine interfaces.

CAS / MDL: 7789-24-4
研究领域: 材料科学 · 柔性电子 · 生物医学工程
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CRYSTAL GROWTH & DESIGN · 2019 · IF 4.153

Increased Concentration of Yb3+ and High Crystal Field Strength in RbTiOPO4:Ta Single Crystal with Optimized Growth

Ziqing Li,Pengfei Zhu,Jimin Ding,Nianjing Ji,Yang Chen,Zhenyan Wang,Xiulan Duan,Huaidong Jiang

Yb-doped inorganic crystals have attracted great attention in both basic and applied research, and the quest for suitable crystal hosts and understanding the corresponding crystal field environments are still worth studying in laser application. In this context, inclusion-free RbTiOPO4:Ta:Yb (RTP:Ta:Yb) single crystals with dimensions up to 3 × 30 × 15 mm3 were grown by top-seeded solution growth method under optimized growth conditions. The good crystalline quality of the as-grown RTP:Ta:Yb crystals were confirmed by X-ray diffraction rocking curve. The chemical compositions of the crystals were determined through electron probe microanalysis (EPMA). The results showed that the Ta distribution coefficient is 0.90–1.28, and the Yb distribution coefficient is 0.13–0.37. Double doping of Ta5+ ions can effectively increase the concentration of Yb3+ ions in the RTP crystal, and the concentration of Yb3+ ion in RTP crystal can reach 1.26 × 1020 atom/cm3. The influence of Ta and Yb dopants on the electronic structures of RTP crystals was studied using high-resolution X-ray photoelectron spectroscopy (XPS), and the chemical strengths of Ti–O and P–O bonds are related to the binding energy difference. RTP:Ta:Yb crystals exhibit excellent transparent performance in the wavelength range of 0.35–4.5 μm, and the transmittance is about 83%. Photoluminescence spectra show five emission peaks of Yb3+ in crystals, and the main emission peak is located at 972 nm. Two different coordination sites for Yb3+ were observed, and their energy levels were determined in the crystal field of the RTP:Ta structure. Furthermore, the crystal field strengths of Yb3+ in different host crystals associated with their distorted coordination environments were evaluated and discussed in detail. The results demonstrate that the RTP:Ta:Yb single crystal endowed with high crystal field strength and good luminescence property is suitable for laser application.

CAS / MDL: 1314-37-0 1314-61-0
研究领域: 材料科学 · 光学
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。