JOM
·
2021
·Vol. 73
·期 12
·4103-4111
·
IF 2.474
Wang Ying,Hou Jiyue,Li Xue,Hu Xiuqiong,Wang Yanjie,Yang Zhengwu,Ai Rui,Zhang Yiyong
This paper proposes the preparation of a S-Se-Ti 3 C 2 T x /TiO 2 cathode by etching Ti 3 AlC 2 with hydrofluoric acid and doping with selenium (Se). Through an electrochemical performance test, selenium is doped into the active material sulfur and forms a sulfur-selenium compound to compensate for the ‘chemical inertness’ of the elemental sulfur, thereby increasing the utilization rate of the active material. Taking advantage of the ability of TiO 2 to absorb polysulfide compounds and the high conductivity of carbides, the Ti 3 C 2 T x composite material, modified with TiO 2 nanodots, is constructed in situ as a sulfur-selenium composite material carrier, achieving a high sulfur content of 80%. S-Se-Ti 3 C 2 Tx/TiO 2 is used as the cathode, and the initial discharge specific capacity is as high as 1073 mAh g −1 , which improves the utilization of active materials and effectively inhibits the shuttle effect of lithium polysulfide intermediates.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2025
·
IF 5.1
Zhihua Zhao,Jingzhao Tian,Xiaobei Xu,Chunhua Zheng,Lan Wu
Elevated concentrations of nitrogen dioxide (NO 2 ) pose detrimental effects on the environment, contributing to pollution in water bodies, soil, and the atmosphere. Moreover, NO 2 , being a potent oxidant, can directly impinge upon the respiratory system, precipitating a range of pulmonary illnesses. Consequently, rigorous surveillance and assessment of NO 2 emissions are of paramount importance for safeguarding environmental integrity and public health. To address this challenge, we fabricated a NO 2 gas sensor using VS 2 /Ti 3 C 2 T x /TiO 2 nanocomposites. The sensors were thoroughly characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). In our tests, the M/v-2 sensor showed excellent performance, with a response of 4.73 at 180 °C to 50 ppm NO 2 , which is 2.5 times that of the Ti 3 C 2 T x /TiO 2 sensor. Additionally, its response time was short (26 s), the recovery time was even shorter than the response time (15 s), and it demonstrated a high response speed to low concentrations of NO 2 (≤10 ppm). Furthermore, the long-term stability was excellent over a period of 45 days. The gathered characteristics indicate that our VS 2 /Ti 3 C 2 T x /TiO 2 gas sensor has great potential for NO 2 detection.
研究领域:
环境科学
·
材料科学
·
传感器技术
✓ 已验证
产品关联
DOI
高影响因子
FUEL
·
2025
·
IF 7.5
Baofang Zhang,Ziyu Zengcai,Wenting Lin,Wenjie Gu,Dizhou Lou,Ruixi Luo,Qingwei Meng,Yunhong Pi,Tiejun Wang
Herein, Cu 2 O/Ti 3 C 2 T x @TiO 2 is designed by facile one-step strategy of glucose oxidation–reduction reaction for efficient H 2 production from the photothermal-driven reforming of methanol solution (PTRM). At 210 °C, the high H 2 production rate of 87404.0 μmol g cat −1 h −1 (apparent quantum efficiency of 20.6 % at 550 nm) over Cu 2 O/Ti 3 C 2 T x @TiO 2 under photothermal-driven condition is roughly 4 times that of the single thermal condition. The excellent photothermal H 2 yield activity over Cu 2 O/Ti 3 C 2 T x @TiO 2 is attributed to effectively separate carriers and reduced activation energy due to the synergistic effect of light and heat (55.05 kJ·mol −1 ) comparing to pure thermal condition (88.29 kJ·mol −1 ), which led to achieve low-temperature H 2 evolution at 95 °C. Additionally, this work demonstrates the excellent photothermal stability of Cu 2 O/Ti 3 C 2 T x @TiO 2 under without KOH condition (average rate 2383.2 μmol g cat −1 h −1 in 72 h), and a total turnover number (TON) up to 1373.
研究领域:
材料科学
·
能源化学
✓ 已验证
产品关联
DOI
高影响因子
TALANTA
·
2024
·
IF 5.6
Konghao Han,Zilong Yan,Zhuang Ding,Pengfei Zhou,Cheng Ye,Ling Qin,Zhiyong Bao,Maofeng Zhang,Wei Zhang
The proliferation of micro/nanoplastics (MNPs) has emerged as a pivotal environmental issue, largely due to their potential for human exposure. Consequently, the development of sensitive and efficient detection methodologies is paramount for elucidating their environmental footprint. Here, we report a novel three-dimensional (3D) surface-enhanced Raman scattering (SERS) sensor, which integrate Ti 3 C 2 T x /TiO 2 /W 18 O 49 semiconductor heterostructure, for the rapid and sensitive detection of MNPs in environmental matrices. The sensor's unique layered architecture and efficient charge transfer mechanism endow it with high sensitivity. It has demonstrated remarkable detection capabilities, achieving a sensitivity of 10 −8 M for Rhodamine 6G (R6G), equating to an enhancement factor (EF) of 2.33 × 10 6 . This level of sensitivity allows for the detection of polystyrene (PS) microplastics at concentration as low as 25 μg/mL, with a relative standard deviation (RSD) of 12.58 %, signifying superior reproducibility. Moreover, the sensor's fingerprinting capabilities enable the identification of a variety of MNPs, including polyethylene (PE) and polyethylene terephthalate (PET), thus facilitating the analysis of complex MNPs mixtures. The sensor's applicability to real-world samples was confirmed through the quantitative detection of PS microplastics in rainwater, soil, and industrial wastewater, with a detection limit of 25 μg/mL and exhibiting good linearity. It is concluded that the 3D SERS sensor is a promising tool for the rapid and precise detection of MNPs across diverse environmental matrices. The advent of this technology marks a significant leap forward in environmental analysis, providing a robust method for the monitoring of MNPs pollution.
研究领域:
环境科学
·
材料科学
·
分析化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FOOD CHEMISTRY
·
2022
·
IF 9.231
Wei Zhong,Jin Zou,Qi Yu,Yansha Gao,Fengli Qu,Shuwu Liu,Hui Zhou,Limin Lu
The development of effective electrochemical methods for the determination of pesticide residues is highly desirable for food safety requirements. Herein, a novel electrochemical sensing strategy for indirect detection of thiabendazole (TBZ) was achieved by monitoring the anodic stripping peak signal change of media Cu 2+ induced by a significant activity difference between active Cu 2+ and inactive Cu 2+ -TBZ complexes. In this sensing system, a heterostructured Ti 3 C 2 T x -TiO 2 composite synthesized via a simple in-situ-oxidization strategy is used as the electrode material to boost the anodic stripping peak signal. After optimizing various conditions, the developed sensor presents satisfactory analytical performance for TBZ assay with a linear range from 0.3 to 100.0 nM and a limit of detection as low as 0.1 nM (S/N = 3). Furthermore, the proposed sensing platform also exhibits outstanding anti-interference, repeatability, and stability, which is effective for the determination of TBZ in fruit and water samples.
研究领域:
食品科学
·
分析化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2023
·
IF 9.9
Huying Yan,Yang Guo,Xingzhi Bai,Jiawei Qi,Haipeng Lu
Optimizing and enhancing the performance of electromagnetic wave (EMW) absorption materials relies on the modification of their composition and structure through heterogeneous interface engineering. Ti 3 C 2 T x ’s high conductivity results in an impedance mismatch, which hinders efficient EMW absorption. Herein, a one–step catalytic chemical vapor deposition (CCVD) method is used to construct the Ti 3 C 2 T x /TiO 2 @C heterogeneous structure. Upon annealing at 500 °C, amorphous carbon is uniformly deposited on the Ti 3 C 2 T x surface, thereby incorporating the scale–like TiO 2 generated during the process. The inclusion of the amorphous carbon layer and TiO 2 reduces the substrate’s conductivity, achieving optimized impedance matching. Additionally, building heterogeneous interfaces between Ti 3 C 2 T x , TiO 2 , and C enriches multiple loss mechanisms involving dipole and interfacial polarization, ultimately enabling optimal EMW absorption performance. The minimum reflection loss ( RL min ) value of Ti 3 C 2 T x /TiO 2 @C–500 is –53.12 dB when its thickness and frequency are 1.15 mm and 13.80 GHz, respectively. Moreover, thermal infrared imaging confirms that coatings fabricated using Ti 3 C 2 T x /TiO 2 @C–500 demonstrate a favorable heat dissipation rate, validating its effectiveness in addressing the challenge of efficient heat dissipation in electronic devices. This study significantly contributes to the progress of two–dimensional (2D) materials, enabling high–performance EMW absorption and expanding their applications in complex scenarios.
研究领域:
材料科学
·
电子工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MATERIALS RESEARCH BULLETIN
·
2024
·
IF 5.3
Mianke Chen,Chenghong Zhang,Ruikai Liu,Kang Qiu,Youlin Gao,Yikang Qiang,Yiqing Yang,Wuyi Chai,Mahmoud A. Khalifa,Jialiang Luo,Wei Ding,Ganhong Zheng,Zhigao Sheng
Multi-layer 2D material assemblies introduce numerous interfaces that would improve microwave absorbing. Here, a 3D porous rGO/Ti 3 C 2 T x /TiO 2 heterostructure was prepared using a one-step hydrothermal synthesis. Due to the presence of the 2D/2D van der Waals heterojunction in rGO/Ti 3 C 2 T x featuring face-to-face contacts, and the 2D/0D heterojunctions in Ti 3 C 2 T x /TiO 2 , the interfacial polarization is optimized. The minimum reflection loss (RL min ) achieves −37.31 dB, and the effective absorption bandwidth (EAB) extends to 6.45 GHz (with<−10 dB). These results not only shed light on understanding and enhancement of interfacial effects, but also provides an appealing mode for the implementation of heterogeneous interfacial engineering using tailored 2D hierarchical structures.
研究领域:
材料科学
·
电磁学
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2024
·
IF 8
Yue Sun,Zhuo Liu,Yuchi Zhang,Le Han,Yan Xu
Photoexcitation is an effective method to promote specific gas sensing performance of semiconductor for electronic device. In this work, an interlayered Ti 3 C 2 T X /TiO 2 /ZnO ternary nanoarchitecture was successfully prepared via sequential etching-intercalation and pyrolysis methods, for which the ZIF-8 nanoparticles were initially incorporated into the adjacent interlayers of laminated Ti 3 C 2 T X MXene derived from HF-etching of Ti 3 AlC 2 MAX phase. The resultant multilayered Ti 3 C 2 T X /ZIF-8 nanocomposite was pyrolyzed at 400 o C to form Ti 3 C 2 T X /TiO 2 /ZnO ternary heterostructure , showing high triethylamine (TEA) sensing performance with R a /R g = 98 at 270 o C under 620 nm red-light irradiation, which is 3.1 times higher than that of the value measured under darkness. A rapid response/recovery time of 17 s/86 s is achieved, and it shows excellent TEA sensing selectivity and long-term cyclic stability. The close-stacked nano-/microstructure of Ti 3 C 2 T X /TiO 2 /ZnO effectively contribute to the diffusion and permeation of gas molecules, as well as the photogeneration and migration of charge carriers, leading to its outstanding photoactivated TEA sensing performance. This work provides a feasible approach to exploring high-performance Mxene hybrids for ultrasensitive TEA monitoring.
研究领域:
材料科学
·
纳米技术
·
化学传感器
·
光化学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2025
·
IF 6.3
Qi Lei,Huajun Xu,Guanyu Ma,Shuo Liang,Zirui Xiao,Yunshu Zhang,Dong Luo,Yu Gao
Two-dimensional MXene materials exhibit exceptional electrical conductivity , which has enabled their widespread utilization as highly efficient anode materials in lithium-ion batteries while demonstrating superior electrochemical characteristics. However, the structural integrity of MXene may be compromised by rapid lithium-ion intercalation, potentially resulting in diminished cycling stability. Herein, we present a dual heterostructured Ti 3 C 2 T x /TiO 2 /La 2 O 3 integrated electrode synthesized through a facile strategy. This architecture synergistically integrates the merits of individual heterostructures , substantially optimizing both electronic configuration and surface morphology of the electrode system , thereby simultaneously enhancing structural stability and energy storage performance. The optimized Ti 3 C 2 T x /TiO 2 /La 2 O 3 dual heterojunction achieves remarkable capacity retention of 319 mAh g −1 after 800 cycles at 0.1 A g −1 . Notably, under elevated current density conditions (1 A g −1 ), the MXene-based anode demonstrates extraordinary cycling durability exceeding 10,000 cycles with 101 % capacity retention. This study establishes a novel methodological paradigm for developing MXene-derived anode materials with exceptional cyclability, suggesting substantial potential for advancement in high-capacity energy storage systems and long-cycle applications within lithium-ion technologies.
✓ 已验证
产品关联
DOI
高影响因子
Small Structures
·
2024
·
IF 13.9
Ziying Ji,Yiran Wu,Lu Liu,Wei Zheng,Meng Wu,Yuexia Li,Zhengming Sun,Guobing Ying
The 2D Ti 3 C 2 T x MXene has a large specific surface area, abundant functional groups, and low work function, which has potential in the field of photocatalytic materials. However, the manufacturing of controllable films with high photocatalytic properties and desirable transmittance is a challenging task. Herein, low-cost, large-scale, and rapid preparation of Ti 3 C 2 T x /TiO 2 flexible composite films have been successfully prepared by inkjet printing technology, which can be applied in complex and special environments, as well as in photoelectrically controllable places for photocatalytic performance. With the increase of the anatase TiO 2 , the transmittance of Ti 3 C 2 T x /TiO 2 films increases from 55.37% to 73.27% at 780 nm, corresponding to the square resistance of 1.112–206.496 kΩ sq −1 and the figure of merit of 0.48–0.005. When the amount of anatase TiO 2 is 15%, the film has the best photocatalytic effect on methylene blue (MB) dye, reaching 68.94%. After five cycles of testing, the degradation efficiency of MB dye decreases by only 5.68%, showing that the film has good cycling stability. This work provides a new research direction for photoelectrically controllable photocatalytic degradation in complex and special environments.
研究领域:
材料科学
·
纳米技术
·
环境科学
·
光催化
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Electronic Materials
·
2024
·
IF 4.3
Zhihua Zhao,Yao Wang,Bo Li,Pu Chen,Guixin Jin,Xiaoqing Shen,Zhigang Shao,Lan Wu
With the rapid advancement of wearable technology, multifunctional sensors have garnered significant attention due to their potential applications in environmental monitoring, health diagnostics, and human−machine interaction. Despite their promise, challenges, such as limited flexibility, insufficient sensitivity, and complex production processes, have hindered their practical deployment. This study presents the fabrication of a multifunctional flexible sensor based on PU-supported Ti3C2Tx/TiO2/PPy yarns for both ammonia (NH3) gas sensing and human motion detection. Key innovations include the incorporation of polypyrrole (PPy) into the Ti3C2Tx MXene structure and the optimization of titanium dioxide (TiO2) content through varying hydrothermal times, which significantly enhance the gas sensing performance. The sensor demonstrates exceptional sensitivity and selectivity toward NH3, with a rapid response and recovery times. Additionally, the PU-supported composite yarns exhibit excellent mechanical flexibility and durability, maintaining stable performance under repeated stretching and bending cycles. In human motion detection, the sensor shows high sensitivity and reliable performance in monitoring various physical activities, making it highly suitable for applications in wearable electronics. These features ensure the sensor’s applicability in diverse settings, promoting safety and health in environments with potential ammonia exposure and enhancing human−machine interactions through accurate motion monitoring.
研究领域:
材料科学
·
传感技术
·
环境监测
·
可穿戴设备
✓ 已验证
产品关联
DOI
高影响因子
ACS Sensors
·
2026
·
IF 10.9
Peng Xu,Yanlei Guo,Xin Lv,Shuting Wei,Dan Yang,Renquan Guan,Yuxin Wang,Yingmin Teng,Aiceng Li,Huaqiao Tan,Zhongling Lang,Zheng Lou,Lili Wang,Zhao Zhao
The necessity for high-efficiency, low-power room-temperature (RT) ammonia (NH3) sensors is particularly acute in environmental monitoring, industrial safety, and medical diagnostics. However, conventional chemiresistive sensors frequently require elevated temperatures to initiate reactions, leading to high energy consumption and potential safety risks. Inspired by plant photosynthesis, this paper successfully designs a ternary S-scheme heterojunction for a photo-activated RT NH3 sensor. The design effectively mimics the efficient charge transfer process in photosynthesis, thereby significantly promoting the separation and migration of photogenerated carriers and enhancing the sensing performance. Experimental results demonstrate exceptional performance under illumination: a high response value of 1679% (representing a 20-fold improvement over the dark state), rapid response and recovery times of 2.1 s and 1.9 s, respectively, along with outstanding selectivity, excellent stability, and a detection limit as low as 17 ppb. This work demonstrates a novel, efficient RT photo-activated NH3 sensor and provides innovative insights into designing biomimetic, smart gas-sensing materials and devices.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）