Micromachines
·
2022
·Vol. 13
·期 8
·1235
·
IF 3.523
Zhi Zhang,Yao Wang,Qun Chen,Qingguo Gao,Liming Liu,Jianjun Yang,Xinjian Pan,Yu Miao,Feng Chi
The electrophoretic display (EPD) has attracted widespread attention due to its great visual perception, energy-saving, portability, and bistability. However, the EPD still has many problems in response time, colorization, etc., which limits its practical application. In this paper, novel blue electrophoretic particles were prepared with copper (II) phthalocyanine and high ionization 1-butyl-1-methyl piperidinium bromide mono ionic liquid. It was shown that electrophoretic particles dispersed in a non-polar tetrachloroethylene medium had high Zeta potential and electrophoretic mobility. At the same time, electrophoretic particles showed better dispersion stability. Finally, the prepared blue electrophoretic particles and white titanium dioxide particles were compounded to prepare blue and white dual-color electrophoretic dispersion. An EPD cell was made to test its performance. The results showed that the prepared blue and white dual-color electrophoretic dispersion could realize a reversible response. Piperidine mono ionic liquid increased the surface potential of copper (II) phthalocyanine from +30.50 mV to +60.27 mV, enhancing it by 97.61%. Therefore, we believed that modifying particles with high ionization mono ionic liquid had great applicability to the modification of electrophoretic particles, and blue particles prepared with piperidine mono ionic liquid as a charge control agent (CCA) were excellent candidates for EPDs.Keywords:zeta potential;ionic liquid;copper (II) phthalocyanine;electrophoretic particle
研究领域:
材料科学
·
电泳显示器
·
纳米技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Surfaces and Interfaces
·
2024
·
IF 5.7
Haoxiong Cui,Zhong Lin,Kelin Zhu,Guoan Cheng,Xiaoling Wu,Ruiting Zheng
The comprehensive investigation was conducted to analyze the corrosion behavior and surface potential of pure copper surfaces in various acidic solutions. We carried out Zeta potential measurement, electrochemical measurement and in situ Raman spectroscopy to investigate the corrosion process and surface potential of copper in acidic solutions with different pH. It was found that the variation in zeta potential with pH corresponds to the corrosion behavior of copper during this process. In 1mmol / L aqueous chloride media, when the pH is greater than 3.5, unalloyed copper is oxidized to monovalent copper. At this stage, as the pH decreases, the zeta potential gradually increases. When the pH reaches 3.5, the Zeta potential reaches the highest, and the rate of cuprous oxide formation reaches the maximum. When the pH continues decrease, unalloyed copper begins to be oxidized to divalent copper, and the zeta potential will also decrease, the surface charge state shifts to the positive direction. Furthermore, our experimental findings are complemented by Density Functional Theory (DFT) calculations.
研究领域:
材料科学
·
电化学
·
表面科学
✓ 已验证
DOI
高影响因子
CHEMICAL PAPERS
·
2020
·Vol. 74
·期 7
·2123-2131
·
IF 1.68
Zhai Xueying,Guo Jingdong,Zhang Wenshu,Yang De’an
In this study, the zeta potential on the surface of copper powder was adjusted by changing the pH value and adding cetyltrimethylammonium bromide (CTAB). Silica sol was coated directly on copper powder through physical adsorption. The as-prepared SiO 2 -coated copper powders were mixed with organic vehicle and screen printed on low-temperature co-fired ceramic substrate to form copper films. The binder-burn-out process of the films was carried out at 550 °C for 1 h in N 2 /H 2 O atmosphere and then sintered at 910 °C for 1 h in N 2 atmosphere. The results proved that zeta potential had a major effect on the coating morphology of SiO 2 -coated copper powder. The SiO 2 -coated copper powder with a weight ratio of 1% showed a uniform and smooth surface. When the CTAB concentration was 1 × 10 –4 mol/L, the copper powder exhibited the highest zeta potential of 98.2 mV, and the copper film had the best conductivity with a sheet resistance of 1.8 mΩ/□.
研究领域:
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
POWDER TECHNOLOGY
·
2022
·
IF 5.64
Chengyang Zhou,Lingyun Liu,Jun Chen,Fanfei Min,Fangqin Lu
The influences of particle size on the flotation separation of kaolinite and quartz was explored by flotation tests of full-size and various sizes, zeta potential analysis. The flotation separation effects of kaolinite and quartz mixed minerals under different conditions were analyzed by calculating the characteristic parameters such as K, R ∞ , Km, SI and SE. Results show that in the sodium oleate scenario, kaolinite has better floatability under neutral conditions, while quartz has better floatability at pH 12. Ca 2+ has little effect on the floatability of kaolinite but it does inhibit the floatability of quartz under acid and weak alkali conditions. As well it can improve the floatability of quartz at a pH 12. In the two mineral flotation separation tests, reverse flotation had better selectivity for coarse-grained minerals. The maximum separation efficiency of the mixed ore with a particle size of 0.125–0.075 mm was 71.88%, the recovery of kaolinite in the concentrate was 84.97%, and the recovery of quartz amounted to 13.10%. It is of great significance to the research on the flotation separation of kaolinite and the high resource utilization of kaolinite.
研究领域:
矿物加工工程
·
材料科学与工程
✓ 已验证
产品关联
DOI
高影响因子
MINERALS ENGINEERING
·
2024
·
IF 4.9
Zuli Mo,Qingliang Wang,Zhimin Guo,Zhiwu Lei,Fang Hu,Eming Hu,Pengfei Hu
Treatment of uranium-containing wastewater has become an increasingly important research focus with the exploitation and utilization of uranium resources. The introduction of new technologies and continuous updating of existing technologies are the urgent tasks for the treatment of uranium-containing wastewater. Ion flotation is one technology with the potential to address uranium contamination. In this study, the improved ion flotation technique for removing U(VI) from acidic solutions was established by colloidal gas aphrons (CGAs). The CGAs were produced by stirring cetyltrimethylammonium bromide (CTAB) solutions at high speed. Measurements of half-life, gas hold-up, bubble size distribution and zeta potential of CGAs have been performed in this work. In the batch process, as CGAs continued to be added, the uranium removal increased steeply at first then slowly, and finally leveled off. At pH 6, the final uranium removal can reach the highest 99.3 % at an initial uranium concentration of 2.5 mg/L. The effective removal of U(VI) by the CGAs formed by cationic CTAB indicated that U(VI) existed as anionic species under these conditions. It was found that the concentration of carbonate ions in solution increased with the increase of flotation time, which may be caused by the dissolution of carbon dioxide brought in by bubbles. The calculation results of Visual MINTEQ software show that the concentration of carbonate ions generated at pH 6 is sufficient for anionic uranium-carbonate to dominate. In addition, it was found that the size and zeta potential of CGAs all played a significant role in removing U(VI) from the acidic solution.
研究领域:
环境科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2023
·
IF 9.5
Yifan Zhang,Yaru Fan,Guoli Zhou,Yijun Cao,Jingtao Wang,Xiaobin Jiang,Ning Zhang,Shaohua Yin
With the rapid development of Li-ion batteries (LiBs), the demand for lithium sharply increased. Salt lakes contribute to major extractable lithium in the world, however, the efficient separation of Mg 2+ and Li + remains a challenge. The PEI-based nanofiltration (NF) membrane shows great potential for Mg 2+ /Li + separation in recent studies, due to its positively charged surface and tunable pore size. In this work, ethylenediamine-terminated polyethyleneimine (EDA@PEI) was utilized as the aqueous monomer reacting with trimesoyl chloride (TMC) via interfacial polymerization (IP) to fabricate a new class of PEI-based NF membranes. This work explored critical membrane fabrication parameters and characterizations of EDA@PEI NF membranes. Additionally, this work compared EDA@PEI-TMC and PEI-TMC membranes on their physicochemical properties and NF performance. The results show that PEI containing EDA groups at ends provides the probability for connection of the backbone via TMC, thus enhancing the cross-linking degree (DNC) of EDA@PEI NF membranes. Meanwhile, the presence of EDA groups enhances the Zeta potential of membranes. The best-performing EDA@PEI-TMC membrane exhibits the highest rejection for Mg 2+ of 99.21 %, and excellent Mg 2+ /Li + separation that S Li/Mg reaches 69.20, 80.62 and 46.79 at Mg 2+ /Li + mass ratios of 40:1, 60:1, and 120:1, respectively. During a 48-h NF test, EDA@PEI-TFC membrane shows consistent performance and steady flux. This work demonstrates the great application potential of EDA@PEI NF membranes for Mg 2+ /Li + separation, and provides a candidate for fabricating PEI-based NF membranes.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
NUCLEAR ENGINEERING AND DESIGN
·
2024
·
IF 1.9
Tao Liu,Haixia Kong,Yongguo Li,Jia Wang,Haifeng Yu,Yuan Li
In this paper, nano-grade aluminum powder was used as raw material to prepare glass fiber filter material with positive Zeta potential by hydrothermal method. Since colloids of activated corrosion products in primary circuit of nuclear power plant are mainly electronegative, the filter material prepared in this experiment was used to remove colloidal particles in coolant by combining traditional mechanical filtration with electrostatic adsorption, thus improving the removal efficiency of colloidal particles. The leaching problem of soluble silicon in glass fiber filter material was studied. The leaching amount of soluble silicon in glass fiber filter material was decreased while the filtration efficiency was improved. Consequently reduce the risk of safe operation of nuclear power plants.
研究领域:
材料科学
·
核工程
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2017
·
IF 4.233
Chenhu Zhang,Sun Wei,Yuehua Hu,Honghu Tang,Jiande Gao,Zhigang Yin,Qingjun Guan
Selective adsorption of tannic acid (TA) on calcite surfaces and the implications of this process for the separation of fluorite ore were studied by microflotation tests, surface adsorption experiments, zeta potential measurements, UV–vis analysis, and X-ray photoelectron spectroscopy (XPS) analysis. The microflotation tests indicated that TA, when added before sodium oleate (NaOl), could selectively depress calcite from fluorite at pH 7. Surface adsorption experiments revealed that TA hinders the interaction of NaOl with calcite. The zeta potential of calcite became more negative with TA than with NaOl. However, the characteristic features of TA adsorption were not observed on fluorite, suggesting that the dominant adsorption sites are dissimilar on the fluorite and calcite surfaces in the pulp. UV–vis spectroscopy, XPS, and solution chemistry analysis were utilized to obtain a better understanding of the mechanism for selective adsorption of TA as well as the key factors determined by the Ca 2+ and Ca(OH) + components on the mineral surfaces. A possible adsorption mechanism along with an adsorption mode is proposed for the surface interaction between TA and calcite.
研究领域:
矿物加工工程
·
表面化学
·
胶体与界面科学
·
资源利用
·
浮选化学
✓ 已验证
DOI
高影响因子
FUEL
·
2024
·
IF 6.7
Yuqi Tang,Wen Xu,Shi Liu,Xuemin Yan,Lu Lai,Weichu Yu,Yuanzhu Mi,Huan Li
A clover-shaped demulsifier (M−MEA) was synthesized via a simple two-step reaction, and its chemical structure was corroborated using 1 H NMR and FT-IR. The demulsification efficacy of M−MEA was investigated on two distinct water-in-oil emulsions. The bottle test results indicated that in a W/O emulsion with 30 % oil content, M−MEA achieved a demulsification efficiency (DE) of 100 % at a concentration of 300 mg/L, temperature of 60 °C, and settling time of 120 min. Similarly, in a W/O emulsion with 70 % oil content, the DE also reached 100 % at a concentration of 500 mg/L and a settling time of 90 min. Moreover, M−MEA exhibited remarkable demulsification performance at high salinity and across a wide pH range. Comparative analysis with other commercially available demulsifiers revealed that M−MEA offered high demulsification efficiency and yielded a clearly separated water phase. The study delved into the demulsification mechanism through assessments of dynamic interfacial tension (IFT), surface tension (ST), three-phase contact angle (TCA), and zeta potential . The findings demonstrated that M−MEA, acting as an effective demulsifier, swiftly migrated to the oil–water interface, displaced the natural surfactant , and destabilized the emulsion, thereby facilitating the oil–water separation of emulsions.
研究领域:
化学工程
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2022
·
IF 8.025
Fang Wang,Long Li,Jibran Iqbal,Zhuoran Yang,Yiping Du
In this study, the magnetic chitosan biochar (MCB) was magnetized by chemical coprecipitation after loading chitosan with Schiff base reaction. The prepared MCB was used to remove amaranth dye in solution. The synthesized MCB was characterized to define its surface morphology and specific elements. The amaranth dye adsorption system was optimized by varying the contact time, pH, and initial concentration. The adsorption of MCB on amaranth dye was measured in a wide pH range. According to Zeta potential , the surface of MCB was positively charged in the acidic pH region, which was more conducive to the adsorption of anionic amaranth dye. In addition, the adsorption data was fitted with the pseudo-first-order model and Langmuir adsorption model and the maximum adsorption capacity reached 404.18 mg/g. The adsorption efficiency of MCB was still above 95% after three cycles of adsorption and desorption. The removal percentage in the real sample of amaranth dye by MCB was within 94.5–98.6% and the RSD was within 0.14–1.08%. The MCB adsorbent with advantages of being easy to prepare, easy to separate from solution after adsorption, has good adsorption performance for amaranth dye and is effective potential adsorbent to remove organic anionic dye in wastewater.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2021
·
IF 4.539
Han Jia,Daofan Wang,Fengbin Lv,Qiang Wang,Li Lv,Xin Wei,Lin Song,Haidong Jia,Kaihe Lv,Dexin Liu
Both negatively charged SiO 2 nanoparticle and positively charged AlOOH nanoparticle have been widely used in various fields, including enhanced oil recovery (EOR). In this study, the mixed binary AlOOH/SiO 2 nanoparticle (MBN) systems are constructed and firstly employed in EOR. The measurements of zeta potential and Z-average diameter indicate that the stable MBN aqueous dispersion could be obtained by controlling AlOOH/SiO 2 mass ratios, which is quantificationally confirmed via the e-DLVO theory. Then the ternary TX-100-AlOOH-SiO 2 (TX-A-S) system exhibits the great ability to stabilize the emulsion at the much low nanoparticle concentration (0.15 wt% in total). The emulsion stability is further evaluated in the harsh conditions (high shear, temperature and electrolyte concentration). Moreover, core flooding and microscopic visualization experiments reflect the TX-A-S stabilized emulsion can dramatically enhance tertiary oil recovery (~23% of initial oil in place), which should be attributed to the high improvement of both displacement and sweep efficiency.
研究领域:
胶体化学
·
石油工程
·
界面科学
✓ 已验证
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2021
·
IF 4.539
Cheng Liu,Xinyue Zhang,Yunfei Zheng,Zijie Ren,Weng Fu,Siyuan Yang
Fluorite is easily affected by the slime coating of fine barite during the froth flotation separation. In this work, the water glass (WG) was utilized as a dispersant to improve the flotation separation performance between fluorite and barite slimes. The single minerals flotation results revealed that barite slimes could be selectively depressed by gelatinized starch (GS), while WG had little effect on the floatability of barite and fluorite using sodium oleate (NaOl) as a collector. The flotation results of artificially mixed minerals showed that the separation efficiency of fluorite from barite was significantly reduced when barite existed as slimes. However, the presence of WG could eliminate the negative effect of barite slimes on the flotation fluorite by using the reagents scheme of GS/NaOl. Zeta potential results indicated that the fluorite surface charge turned from positive to negative with the addition of WG, then the barite slimes coating was detached from the fluorite surface because of the electrostatic repulsion, allowing the cleaning fluorite surface to once again interact with NaOl. The DLVO calculation was also conducted to reveal the agglomerate and disperse of different particles in the flotation system of fluorite-barite slimes.
研究领域:
矿物加工工程
·
浮选化学
·
胶体与界面科学
·
资源综合利用
·
无机非金属材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）