碱性磷酸酶 (S-AKP/ALP)广泛分布于动物组织、土壤及微生物中，可催化磷酸单酯水解脱磷酸反应。生物样本中，血清或组织 AKP/ALP 活性异常可反映骨骼代谢、肝胆损伤、细胞分化状态，常用于病理模型评估与细胞成骨分化功能检测。土壤中碱性磷酸酶是关键土壤酶指标，参与土壤有机磷矿化分解，将有机磷转化为植物可利用无机磷，其活性高低直接表征土壤磷素供应能力、微生物代谢水平及土壤肥力状况，是土壤质量评价、施肥效应与生态修复研究的重要参数。

本试剂盒检测原理为碱性磷酸酶（S-AKP/ALP）能够在碱性环境中催化磷酸苯二钠水解生成苯酚和磷酸氢二钠，在碱性条件下苯酚与氨基安替比林结合，并经氧化生成红色醌式结构物，呈深浅不一的红色，产物红色越深说明碱性磷酸酶活性越高，反之则酶活性越低，通过分光光度计测定510 nm 处吸光度，就可以计算出碱性磷酸酶活性水平。

A1515886	组件	物料外观	50T	100T	储存条件	单次测试使用量
A1515886A	检测缓冲液	无色液体	25 mL	50 mL	2-8℃.	500 µL
A1515886B	提取液	无色液体	200 mL	400 mL	2-8℃.	按需
A1515886C	显色底物	无色液体	25 mL	50 mL	2-8℃.避光.	500 µL
A1515886D	显色液 A	浅黄液体	15 mL	30 mL	2-8℃.避光.	300 µL
A1515886E	显色液 B	浅黄液体	60 mL	120 mL	2-8℃.避光.	1200 µL
A1515886F	标准品(1mg/mL)	无色液体	2.0 mL	2.0 mL	2-8℃.避光.	按需

注意：显色液B和标准品有一定刺激性或毒性，请规范穿戴实验服和手套，避免接触到皮肤。

使用方法

1. 自备试剂耗材

(1) PBS，去离子水，1.5 mL EP管。

(2) 37℃恒温培养箱或者水浴锅，比色杯，可见分光光度计 (能测 510 nm 处的吸光度)。

2. 样品准备

(1) 组织样本：请尽量使用新鲜的组织样本进行测定。每10 mg组织样本加入100-200 μL提取液，快速冰上匀浆（匀浆器提前放冰上预冷）。匀浆后的样本，4℃，8,000 g 离心10 min，取上清液，置冰上待测。

(2) 血液、血浆或者尿液样品：对于血清和血浆样品，按照常规方法制备后，可直接用于该试剂盒的检测；尿液样本通常也可以直接用于该试剂盒检测。

(3) 细胞 (菌)样本：请尽量使用新鲜的细胞 (菌)进行测定，而不要使用冻存的细胞（菌）进行测定。收集细胞 (菌)，首先用预冷的PBS清洗细胞 (菌)2 次 (PBS 重悬，4℃ 500 g 离心 5 min)，1×10⁶ 个细胞 (菌)建议加入100-200 μL提取液重悬，冰浴超声波破碎 (200 W，超声 2 s，间隔 3 s，5min)，4℃，8,000 g 离心 5 min，取上清液，置冰上待测。

3. 样品检测

建议正式实验前，选取2个样本做预测定，了解实验样品情况，熟悉流程，避免样本和试剂浪费。

(1) 标曲稀释：取0.1 mL标准品(1 mg/mL) + 1.9 mL去离子水，配制成0.05 mg/mL的标准品工作液，然后将标准品工作液按照下表稀释。

标准品 (0.05mg/mL) (mL)	0	0.05	0.1	0.2	0.3	0.4	0.5
去离子水 (mL)	0.5	0.45	0.4	0.3	0.2	0.1	0
相当于金氏单位 (U/L)	0	5	10	20	30	40	50

(2) 显色工作液液配制：按照显色液A:显色液B=1:4比例混匀配制，以配制1500 μL 显色工作液为例，取300 μL 显色液A和1200 μL 显色液B混匀即可。显色工作液需现用现配。

(3) 上机检测：在1.5 mL EP管中按照下表，依次加入各试剂

试剂名称	测定管	对照管	空白管	标准管
待测样品	500 μL	500 μL	-	-
显色底物	500 μL	-	500 μL	500 μL
去离子水	-	500 μL	500 μL	-
标准品	-	-	-	500 μL
检测缓冲液	500 μL	500 μL	500 μL	500 μL
振荡混匀后于37 ℃避光孵育15 min。
显色工作液	1500 μL	1500 μL	1500 μL	1500 μL
混匀后，避光静置2 min，然后吸取上清至1 mL比色杯中（比色杯光径1 cm）读取 A₅₁₀ 。ΔA=A_测定 - A_对照；Δ标准=A_标准 - A_空白

4. 结果计算

(1) 标准曲线：y=0.0253*X + 0.0114(仅供参考)；x是标苯酚浓度(μg/mL)，y 是△标准。算出样品ΔA的值，与标准曲线对比，即可算出样品中生成的苯酚浓度，然后换算成酶活单位。

(2) 碱性磷酸酶金氏活性单位定义：在 37℃条件下，100 mL待测样品与显色底物作用15 min，产生1 mg酚为一个金氏单位。

注意事项

1. 显色工作液需现用现配，需避光放置。

2. 显色液B和标准品有一定刺激性或者毒性，在操作中，请规范穿戴实验服和手套，避免接触到皮肤。

3. 本试剂盒仅用做科研研究，不得用于临床检测。

Alkaline phosphatase (S-AKP/ALP) is widely distributed in animal tissues, soil and microorganisms, and catalyzes the hydrolytic dephosphorylation of phosphate monoesters. In biological samples, abnormal AKP/ALP activity in serum or tissues reflects bone metabolism, hepatobiliary injury and cell differentiation status, and is frequently applied in pathological model evaluation and osteogenic differentiation assay. Soil‑borne alkaline phosphatase serves as a critical soil enzyme indicator. It participates in the mineralization and decomposition of soil organic phosphorus, converting organic phosphorus into plant‑available inorganic phosphorus. Its activity directly characterizes soil phosphorus supply capacity, microbial metabolic level and soil fertility, acting as an essential parameter for soil quality assessment, fertilization‑effect investigation and ecological restoration research.

The assay principle of this kit is described as follows. Under alkaline conditions, S-AKP/ALP catalyzes the hydrolysis of disodium phenyl phosphate to produce phenol and disodium hydrogen phosphate. Phenol reacts with 4-aminoantipyrine under alkaline environment and is oxidized to form red quinonoid compounds. The red color intensity is positively correlated with alkaline phosphatase activity. Higher enzyme activity yields deeper red color, and vice versa. The absorbance is measured at 510 nm using a spectrophotometer to calculate alkaline phosphatase activity.

A1515886	Components	Appearance	50T	100T	Storage	Usage volume per test
A1515886A	Assay Buffer	Colorless liquid	25 mL	50 mL	2-8℃.	500 µL
A1515886B	Extraction Buffer	Colorless liquid	200 mL	400 mL	2-8℃.	As need
A1515886C	Chromogenic substrate	Colorless liquid	25 mL	50 mL	2-8℃.Store in the dark.	500 µL
A1515886D	Chromogenic Solution A	Light yellow liquid	15 mL	30 mL	2-8℃.Store in the dark.	300 µL
A1515886E	Chromogenic Solution B	Light yellow liquid	60 mL	120 mL	2-8℃.Store in the dark.	1200 µL
A1515886F	Standard (1mg/mL)	Colorless liquid	2.0 mL	2.0 mL	2-8℃.Store in the dark.	As need

Note: Chromogenic Solution B and standard solution are irritant and toxic. Wear lab coat and gloves properly during operation to avoid skin contact.

Usage Method

1. Self-supplied Reagents and Consumables

(1) PBS, Deionized water, 1.5 mL EP tube.

(2) Incubator or water bath set at 37°C; cuvette or visible spectrophotometer (capable of measuring absorbance at 510 nm).

2. Sample Preparation

(1) Tissue samples: Use fresh tissue samples for determination whenever possible. Add 100‑200 μL of Extraction Buffer per 10 mg tissue sample, and perform rapid homogenization on ice (pre‑cool the homogenizer on ice in advance). Centrifuge the homogenate at 8 000 g for 10 min at 4 °C. Collect the supernatant and keep it on ice for subsequent assay.

(2) Blood, plasma or urine samples: Serum and plasma samples can be directly assayed with this kit after routine preparation; urine samples are generally suitable for direct detection as well.

(3) Cell (bacterial) samples: Fresh cells/bacteria are recommended instead of frozen ones. Harvest cells/bacteria and wash twice with pre‑cooled PBS (resuspend in PBS, centrifuge at 500 g for 5 min at 4 °C). For 1×10⁶ cells or bacteria, resuspend in 100‑200 μL Extraction Buffer. Lyse by sonication on ice (200 W, 2 s pulse on, 3 s pulse off, total 5 min). Centrifuge the lysate at 8 000 g for 5 min at 4 °C. Collect the supernatant and keep on ice for testing.

3. Sample Detection

It is recommended to perform a pre-test with 2 samples prior to the formal experiment to characterize sample properties and get familiar with the operating procedure, so as to avoid waste of samples and reagents.

(1) Standard Curve Dilution: Pipette 0.1 mL of standard stock solution (1 mg/mL) and mix with 1.9 mL deionized water to prepare 0.05 mg/mL standard working solution. Then dilute the standard working solution according to the table below.

Standard (0.05mg/mL) (mL)	0	0.05	0.1	0.2	0.3	0.4	0.5
Deionized water (mL)	0.5	0.45	0.4	0.3	0.2	0.1	0
Corresponding King’s unit (U/L)	0	5	10	20	30	40	50

(2) Preparation of Chromogenic Working Solution: Mix Chromogenic Solution A and Chromogenic Solution B at a volume ratio of 1:4. For example, to prepare 1500 μL chromogenic working solution, combine 300 μL Chromogenic Solution A with 1200 μL Chromogenic Solution B and mix thoroughly. The Chromogenic Working Solution is recommended to be prepared fresh before use.

(3) Instrument assay: Pipette each reagent sequentially into a 1.5 mL EP tube as shown in the table below.

Reagent Name	Sample Tube	Control Tube	Blank Tube	Standard Tube
Sample to be tested	500 μL	500 μL	-	-
Chromogenic substrate	500 μL	-	500 μL	500 μL
Deionized Water	-	500 μL	500 μL	-
Standard	-	-	-	500 μL
Assay Buffer	500 μL	500 μL	500 μL	500 μL
Mix thoroughly by shaking, then incubate at 37 °C in the dark for 15 min.
Chromogenic Working Solution	1500 μL	1500 μL	1500 μL	1500 μL
Mix well and stand for 2 min in the dark, then transfer the supernatant into a 1 mL cuvette (1 cm light path), and read A₅₁₀. ΔA = A_sample − A_control； Δ_standard=A_standard - A_blank.

4. Result Calculation

(1) Standard curve: (y = 0.0253*X + 0.0114) (for reference only); where X is phenol concentration (μg/mL), and y is Δstandard. Calculate the ΔA value of the sample. Compare it against the standard curve to obtain the phenol concentration produced in the sample, and further convert it into enzyme activity units.

(2) Definition of King’s unit for alkaline phosphatase activity: Under 37 °C, one King’s unit is defined as the amount of enzyme that produces 1 mg of phenol after 15 min reaction between 100 mL test sample and chromogenic substrate.

Precautions

1. The chromogenic working solution shall be freshly prepared before use and stored away from light.

2. Chromogenic Solution B and standard solution are irritant and toxic. Wear lab coat and gloves properly during operation to avoid skin contact.

3. This kit is for research‑only purposes and shall not be used for clinical diagnosis.

规格

别名

碱性磷酸酶(ALP)比色法测试盒 | 碱性磷酸酶(ALP)检测试剂盒(磷酸苯二钠比色法)

英文别名

Alkaline Phosphatase (ALP) Activity Assay Kit

规格或纯度

BioReagent, 比色法, 适用于分析, 标曲法

英文名称

Alkaline Phosphatase (S-AKP/ALP) Activity Assay Kit (Disodium Phenyl Phosphate, Colorimetric Method)

应用

细胞代谢

样品类型

动物组织, 细胞, 血浆, 血清

检测范围

5 U/L-50 U/L

检测方法

磷酸苯二钠，比色法

定量&半定量

定量

检测仪器

可见光分光光度计

检测波长

510nm

敏感性

Light-sensitive

检测时长

15 min

样本体积

500 μL

储存与运输

储存条件

2-8°C储存,避光

运输条件

低温运输

稳定性与储存

各组分在相应的储存条件下保质期1年。

组分与储存

A1515886	组件	物料外观	50T	100T	储存	单次测试使用量
A1515886A	检测缓冲液	无色液体	25 mL	50 mL	2-8℃.	500 µL
A1515886B	提取液	无色液体	200 mL	400 mL	2-8℃.	按需
A1515886C	显色底物	无色液体	25 mL	50 mL	2-8℃.避光.	500 µL
A1515886D	显色液 A	浅黄液体	15 mL	30 mL	2-8℃.避光.	300 µL
A1515886E	显色液 B	浅黄液体	60 mL	120 mL	2-8℃.避光.	1200 µL
A1515886F	标准品(1mg/mL)	无色液体	2.0 mL	2.0 mL	2-8℃.避光.	按需

技术文档

📋 安全数据表 (SDS)

全面的危险、操作、储存及法规合规文件。

下载 SDS →

✅ 分析证书 (COA)

批次质量数据。输入批号以获取对应 COA。

查询 COA →

📊 产品数据表

产品规格和应用的快速参考摘要。

查看数据表 →

🔬 规格说明书

该级别的完整质量属性和验收标准。

查看规格说明 →

高级数据

质检证书（CoA,COO,BSE/TSE 和分析图谱)

C of A & Other Certificates(BSE/TSE, COO):

输入批号以搜索分析图谱:

技术文档和文章

碱性磷酸酶（ALP/AKP）活性检测方法比较：酶学特征、底物体系与实验应用选择

目录：技术文章

探索主题:

碱性磷酸酶微量法比色法 ALP活性检测 AKP活性检测 pNPP法磷酸苯二钠法酶活分析

Comparison of Alkaline Phosphatase (ALP/AKP) Activity Assay Methods: Enzymatic Features, Substrate Systems, and Experimental Application Selection

目录：技术文章

探索主题:

Alkaline phosphatase Colorimetric assay ALP activity assays AKP activity assay pNPP method Disodium Phenyl Phosphate Method Microassay Enzyme Activity Analysis

肝纤维化动物模型构建与评价：毒性损伤、胆汁淤积、免疫炎症和代谢相关模型

目录：技术文章

探索主题:

动物造模细胞外基质四氯化碳肝纤维化硫代乙酰胺胆管结扎 NASH 肝星状细胞 TGF-β/Smad

Construction and Evaluation of Hepatic Fibrosis Animal Models: Toxic Injury, Cholestasis, Immune Inflammation, and Metabolism-Related Models

目录：技术文章

探索主题:

NASH TGF-β/Smad

骨代谢疾病动物模型：造模方法与实验评价

目录：技术文章

探索主题:

动物模型骨重塑骨代谢疾病骨质疏松 Micro-CT 成骨破骨组织学

Bone Metabolic Disease Animal Models: Modeling Methods and Experimental Evaluation

目录：技术文章

探索主题:

Animal Models Osteoclast bone remodeling Micro-CT metabolic bone disease osteoporosis osteogenesis histology

骨重塑相关酶的功能分工：ALP、TRAP、Cathepsin K与基质降解酶

目录：技术文章

探索主题:

碱性磷酸酶 TRAP 破骨细胞骨重塑骨基质 Cathepsin K MMP9 MMP13

Functional Division of Bone Remodeling-Related Enzymes: ALP, TRAP, Cathepsin K, and Matrix-Degrading Enzymes

目录：技术文章

探索主题:

Alkaline phosphatase TRAP Osteoclast bone remodeling bone matrix Cathepsin K MMP9 MMP13

溶液计算器

摩尔浓度计算器

计算溶液所需的质量、体积或浓度。

质量

浓度

体积

分子量

g/mol

稀释计算器

计算配制储备溶液所需的稀释度。

浓度1（C1）

体积 1 (V1)

浓度 2 (C2)

体积 2 (V2)

复溶计算器

复溶计算器允许您快速计算试剂的体积，以复溶小瓶。只需输入试剂的质量和目标浓度，计算器将确定其余部分。

体积（添加到小瓶中）

质量（小瓶）

所需的复溶浓度

需要帮助选择级别？

我们的级别选择指南涵盖了目录中所有的变体的纯度、稳定剂状态和应用适用性。

查看 BioReagent 级别指南 → 查看 Suitable for Analysis 级别指南 → 查看 Colorimetry 级别指南 → 查看 Standard Curve Method 级别指南 →

大包装与定制包装 需要更大包装或定制规格？请联系我们的团队获取专属报价。

碱性磷酸酶（S-AKP/ALP）活性检测试剂盒 (磷酸苯二钠, 比色法)

储存与运输

质量文档

文献证明

概述

规格

技术文档

📋 安全数据表 (SDS)

✅ 分析证书 (COA)

📊 产品数据表

🔬 规格说明书

高级数据

摩尔浓度计算器

稀释计算器

复溶计算器

需要帮助选择级别？

查看相关“主题”系列

相关产品