高灵敏多重探针法 qPCR预混液 (2×, UDG)

货号: H1548032
有货
级别和纯度: BioReagent ? 生物试剂级(BioReagent)—— 经测试适用于生命科学和分子生物学。适用于需要生物相容性的细胞培养、检测和生化工作。 分子生物学级 ? 适用于分子生物学 —— 不含降解 DNA/RNA 的核酸酶和污染物。适用于克隆、PCR 和需要洁净试剂的核酸工作。 2×
★
规格
库存
价格
数量
1ml
H1548032-1ml
期货 Stock Image
¥339.90
5ml
H1548032-5ml
期货 Stock Image
¥1,399.90
请输入您要添加的产品数量

概述

高灵敏多重探针法 qPCR预混液 (2×, UDG) 是一款基于探针法设计开发的高灵敏多重 Real Time PCR (qPCR) 反应的通用试剂。该产品包含了除模板、引物、探针外所有的组分。高效的热启动 Taq Pro DNA Polymerase,配合针对多重反应而优化的缓冲液,可以有效抑制非特异性扩增,大幅增加 qPCR 扩增效率以及多重检测的灵敏度,参比染料 ROX 随试剂盒提供。

本产品使用前只需要加入引物、模板、探针、ROX (根据使用的机型而定)、水。试剂盒可在较宽的浓度范围内得到良好的扩增曲线,适用于对多个靶基因的定量、定性和 SNP 检测,具有重复性好、可信度高、并兼容各种不同类型的 qPCR 探针的特点。试剂中引入了 dUTP、UNG/UDG 防污染系统,室温下即可发挥作用,可消除扩增产物污染对 qPCR 的影响,保证结果的准确性。

组分与储存:

组分货号组分名称物理外观1mL
5mL
储存
H1548032A高灵敏多重探针法 qPCR预混液 (2×, UDG)
液体1mL
5mL
-20℃
H1548032BROX High (50×)
液体40μl
200μl
-20℃. 避光
H1548032CROX Low (50×)
液体40μl
200μl
-20℃. 避光
注:请按照推荐的储存温度保存,避免反复冻融。

产品应用:

1. 基因表达分析;

2. 低拷贝基因检测;

3. SNP 和等位基因分型;

4. 测序和微阵列结果的验证。

注意事项:

1. 使用前请务必确保产品完全融化并充分混匀。

2. 上机前要离心,避免 PCR 管内气泡干扰荧光信号。

3. 使用适当的引物设计软件来设计引物和 Taqman 探针,Taqman 探针需位于引物扩增区域内部,避免与引物重叠或形成二级结构。Tm 值应比引物高 5-10℃,确保探针先于引物退火。

4. 确认淬灭基团(如 BHQ、TAMRA)和报告基团(如FAM、HEX)匹配仪器检测通道。

5. 根据不同仪器选择适配的 ROX。

仪器与 ROX 参比染料对照表:

仪器
ROX 参比染料
Applied Biosystems®5700, 7000, 7300, 7700, 7900HT,
StepOne™, and StepOnePlus™
ROX High
Applied Biosystems®7500, ViiA™7, QuantStudio™ 12K Flex, Agilent
Mx3000P™, Mx3005P™, and Mx4000™
ROX Low
Rotor-Gene™, DNA Engine Opticon™, Opticon™ 2, Chromo 4™ Real-Time
Detector, Mastercycler® ep realplex, Smart Cycler®, Roche LightCycler®
480, Roche LightCycler® Nano, Bio-Rad CFX96, and Illumina Eco™
No ROX

实验流程:

1. 反应体系配制

1.1. 配制前,确保所有组分充分混匀;

1.2. 按照下表配制反应体系:

组分名称
加样体积
高灵敏多重探针法 qPCR预混液 (2×, UDG)
10μL
Forward Primer (10μM) 
0.4μL
Reverse Primer (10μM)
0.4μL
Probe (10μM)
0.4μL
Template
As Required (推荐 2μL)
ROX Low/High (50×)
0.4μL
ddH₂O
补至 20μL

a. 反应体系可以在 5-25μL 范围调整 (各组分按比例变化),不建议>50μL。

b. 引物和探针反应终浓度可以在 0.1-1μM 之间调整。

c. 使用时共同组分最好先配成预混液。

d. ROX 根据机型使用。

1.3. 盖好PCR 管盖,瞬时离心。

2. 反应程序

qPCR 标准程序:

a. 预变性时间设置在 30sec-5min,若模板 GC 含量较高可适当延长预变性时间至 5min。

b. 变性时间:标准程序选择10 sec,快速程序可以选择3-10sec。

c. 退火/延伸温度需要依据引物和探针 Tm 值确定,一般 50-65℃,初次可使用 60℃ 做预实验。

d. 退火/延伸时间根据扩增片段长度可在 20-45sec 之间调整。

常见问题与解决方法:

1. 扩增曲线异常的原因及解决办法是什么?

答:① 如果扩增曲线不光滑,则需要重新校正系统,提高模板浓度,检查 ROX 是否使用错误。

       ② 如果扩增曲线出现断裂或下滑,则可能是模板浓度过高或基线选取范围不当导致,可以降低模板或重新设置基线。

       ③ 如果个别扩增曲线骤降,则可能是反应管有气泡,所以上机前应先离心。

2. 如果反应结束无扩增曲线怎么办?

答:①可能是循环数不够:一般设 40 个循环,但过多循环数会增加背景信号,降低数据可信度。

       ② 确认程序中是否设置信号采集:两步法一般在退火/延伸阶段采集信号;三步法在延伸阶段采集信号。

       ③ 引物降解:PAGE 检测排除其降解的可能性。

       ④ 模板浓度太低:减少稀释度重复实验,先从高浓度做起。

       ⑤ 模板降解:重新制备模板。

3. Ct 值太高怎么办?

答:① 扩增效率低:优化反应条件,尝试三步法扩增或重新设计合成引物。

       ② 模板浓度低:减少模板稀释度,先从高浓度做起。

       ③ 模板降解:重新制备模板。

       ④ PCR 产物太长:推荐 PCR 产物长度 80-150bp。

       ⑤ 存在PCR抑制剂:若为模板带入,加大模板稀释倍数或重新制备模板。

4. 阴性对照出现明显扩增怎么办?

答:① 引物设计不合理:重新设计并合成引物。

5. 标准曲线线性关系不佳怎么办?

答:① 加样误差:提高模板稀释倍数,提高加样体积。

       ② 标准品降解:重新制备标准品。

       ③ 模板浓度太高:提高模板稀释倍数。

6. 实验重复性差怎么办?

答:① 加样体积不一致:使用更好的移液器;将模板做高倍稀释,适当提高加样体积。

       ② 模板浓度太低:模板浓度越低,重复性越差,减少模板稀释度或提高加样体积。

Highly Sensitive Multiplex Probe qPCR Master Mix (2×, UDG) is a universal reagent designed for high-sensitivity multiplex probe-based real-time PCR (qPCR) assays. This product contains all reaction components except templates, primers and probes. It utilizes high-efficiency hot-start Taq Pro DNA Polymerase alongside a buffer optimized for multiplex reactions, which effectively suppresses non-specific amplification and greatly improves qPCR amplification efficiency and multiplex detection sensitivity. The ROX reference dye is supplied with the kit.

Prior to use, only primers, template, probes, ROX (instrument-dependent) and nuclease-free water need to be added. The kit produces consistent, satisfactory amplification curves over a wide concentration range. It is suitable for quantitative, qualitative and SNP detection of multiple target genes, featuring excellent reproducibility, high reliability, and compatibility with various types of qPCR probes. The reagent incorporates the dUTP-UNG/UDG anti-contamination system, which functions at room temperature to eliminate the interference of amplicon contamination on qPCR and ensure the accuracy of test results.

Contents & Storage: 

Component No.
Component Name
Appearance
1mL
5mL
Storage
H1548032AHighly Sensitive Multiplex Probe qPCR Master Mix (2×, UDG)
Liquid
1mL
5mL
-20℃
H1548032BROX High (50×)
Liquid
40μl
200μl
-20℃. Store in the dark.
H1548032CROX Low (50×)
Liquid
40μl
200μl
-20℃. Store in the dark.
Note: Store at the recommended temperature and avoid repeated freeze-thaw cycles.

Applications:

1. Gene expression analysis;

2. Low-copy gene detection;

3. SNP and allelic genotyping;

4. Validation of sequencing and microarray results.

Precautions:

1. Ensure the product is completely thawed and thoroughly mixed before use.

2. Spin down briefly before loading onto the instrument to prevent air bubbles in PCR tubes from interfering with fluorescence signals.

3. Design primers and TaqMan probes using appropriate primer design software. The TaqMan probe must lie within the amplicon defined by the primers; avoid overlapping with primers or secondary structure formation. The Tm value of the probe should be 5–10 °C higher than that of the primers to ensure the probe anneals prior to the primers.

4. Verify that the quencher (e.g., BHQ, TAMRA) and reporter dye (e.g., FAM, HEX) are compatible with the detection channels of your instrument.

5. Select the appropriate ROX variant according to your qPCR instrument.

Instrument vs. ROX Reference Dye Table:


Instrument
ROX Reference Dye
Applied Biosystems®5700, 7000, 7300, 7700, 7900HT,
StepOne™, and StepOnePlus™
ROX High
Applied Biosystems®7500, ViiA™7, QuantStudio™ 12K Flex, Agilent
Mx3000P™, Mx3005P™, and Mx4000™
ROX Low
Rotor-Gene™, DNA Engine Opticon™, Opticon™ 2, Chromo 4™ Real-Time
Detector, Mastercycler® ep realplex, Smart Cycler®, Roche LightCycler®
480, Roche LightCycler® Nano, Bio-Rad CFX96, and Illumina Eco™
No ROX
Experimental Procedure:
1. Reaction Setup
1.1. Ensure all components are thoroughly mixed before preparation.
1.2. Prepare the reaction system according to the table below:
Components
Volume
Highly Sensitive Multiplex Probe qPCR Master Mix (2×, UDG)
10μL
Forward Primer (10μM) 
0.4μL
Reverse Primer (10μM)
0.4μL
Probe (10μM)
0.4μL
Template
As Required (2μL recommended)
ROX Low/High (50×)
0.4μL
ddH₂O
To 20μL

a. The total reaction volume can be adjusted between 5–25 μL (all components scaled proportionally); volumes greater than 50 μL are not recommended.

b. The final working concentration of primers and probes can be adjusted from 0.1–1 μM.

c. It is recommended to prepare a master mix for shared components.

d. ROX is added according to the instrument used.

2. Thermal Cycling Program

Standard qPCR Program:


a. The initial denaturation time can be set from 30 sec to 5 min. For templates with high GC content, the initial denaturation time can be extended up to 5 min.

b. Denaturation time: 10 sec for the standard protocol; 3–10 sec for the fast protocol.

c. The annealing/extension temperature is determined by the Tm value of primers and probes, generally ranging from 50 to 65 °C. 60 °C is recommended for preliminary tests.

d. The annealing/extension time can be adjusted between 20–45 sec according to the amplicon length.

Troubleshooting:

1. What are the causes and solutions for abnormal amplification curves?

Answer: ① If the amplification curve is noisy, recalibrate the instrument, increase the template concentration, and verify that the correct ROX is used.

② If the amplification curve breaks or drifts downward, it may be caused by excessive template concentration or improper baseline selection. Reduce template input or reset the baseline.

③ If individual amplification curves drop abruptly, air bubbles may exist in the reaction tube. Spin down briefly before loading onto the instrument.

2. What to do if no amplification curve is obtained after the run?

Answer: ① Insufficient cycle number: 40 cycles are commonly used. Excessive cycles will raise background signals and reduce data reliability.

② Confirm signal acquisition is enabled in the program: for two-step qPCR, collect signals at the annealing/extension step; for three-step qPCR, collect signals at the extension step.

③ Primer degradation: verify primer integrity by PAGE.

④ Template concentration is too low: reduce dilution factor and repeat the assay, starting with a higher template concentration.

⑤ Template degradation: prepare fresh template.

3. What to do if Ct values are too high?

Answer: ① Low amplification efficiency: optimize reaction conditions, try a three-step cycling protocol, or redesign and resynthesize primers.

② Low template concentration: reduce dilution factor and start with a higher template concentration.

③ Template degradation: prepare fresh template.

④ Overlong PCR amplicon: recommended amplicon length is 80–150 bp.

⑤ Presence of PCR inhibitors: if inhibitors are carried over with the template, further dilute the template or prepare fresh template.

4. What to do if the negative control shows obvious amplification?

Answer: ① Poor primer design: redesign and resynthesize primers.

5. What to do if the standard curve shows poor linearity?

Answer: ① Pipetting error: increase template dilution factor and the volume of pipetted sample.

② Degraded standard: prepare fresh standard material.

③ Excessively high template concentration: increase template dilution factor.

6. What to do if assay reproducibility is poor?

Answer: ① Inconsistent pipetted volume: use a high-quality pipette; prepare template at a higher dilution and increase the loading volume appropriately.

② Low template concentration: reproducibility deteriorates at low template levels. Reduce the dilution factor or increase the loading volume.

规格

规格或纯度
BioReagent, 分子生物学级, 2×
英文名称
Highly Sensitive Multiplex Probe qPCR Master Mix (2×, UDG)
敏感性
Light-sensitive
储存与运输
储存条件
避光,-20°C储存,避免反复冻融
运输条件
超低温运输
稳定性与储存
Store at -20℃ long term (36 months). Store in the dark. Avoid freeze/thaw cycle.
组分与储存
组分货号组分名称物理外观1mL
5mL
储存
H1548032A高灵敏多重探针法 qPCR预混液 (2×, UDG)液体1mL
5mL
-20℃
H1548032BROX High (50×)
液体40μl
200μl
-20℃. 避光
H1548032CROX Low (50×)
液体40μl
200μl
-20℃. 避光
注:请按照推荐的储存温度保存,避免反复冻融。

高级数据

质检证书(CoA,COO,BSE/TSE 和分析图谱)
C of A & Other Certificates(BSE/TSE, COO):
输入批号以搜索分析图谱:
溶液计算器