已核实 DOI 相关产品: 0

Dual-Phase Interpenetrating Reinforcement Enables an Ultrathin Sodium Metal Anode for High-Energy-Density Batteries

Journal 2026 · IF 12.1 · 45(9): e70545 · 发表于 2026 年 9 月 11 日
作者: Hao Yao,Lin Fu,Jingqian Wang,Yishuo Hui,Chunliang Yang,Yuanjian Li,Shuo Geng
阅读全文 在 PubMed 查看

摘要

en This link goes to a English section zh This link goes to a Chinese section Ultrathin sodium (Na) metal anodes (< 40 μm) with superior electrochemical performance are essential in developing high-energy-density sodium metal batteries (SMBs). Nonetheless, Metallic Na's poor processability hinders its practical application. Hence, a dual-phase interpenetrating reinforcement strategy is proposed to fabricate sodium/sodium phosphide–carbon nanotube (Na/Na 3 P5-CNT10, NNP5C10) composite foils with controllable thickness (40−15 μm) by mechanical kneading operation. Sodium phosphide (Na 3 P) is in situ formed through a pressure-induced reaction between red phosphorus (RP) and metallic Na. The resulting Na 3 P and carbon nanotube (CNT) are uniformly embedded within the Na matrix to form an interpenetrating Na 3 P-CNT framework. Na 3 P impedes dislocation motion, whereas CNT provides interfacial lubrication and crack-bridging, enabling smooth separation and reliable thinning of the composite foil. This mixed-conductive framework accelerates ionic/electronic transport, lowers the Na nucleation barrier, and homogenizes Na deposition. As a result, a symmetric cell employing 30 μm-thick NNP5C10 composite foils achieves a long-term cycling stability of 2500 h at 0.5 mA cm −2 and 0.5 mAh cm −2 . When paired with a Na 3 V 2 (PO 4 ) 3 (NVP) cathode, the full cell with a 20 μm-thick NNP5C10 anode achieves a high energy density of ∼276 Wh kg −1 at 0.2C with a low negative-to-positive (N/P) capacity ratio of ∼1.9. This study demonstrates a viable pathway in fabricating ultrathin Na metal anodes with high capacity, thereby promoting the development of high-energy-density SMBs. 摘要 en This link goes to a English section zh This link goes to a Chinese section 电化学性能优异的超薄钠(Sodium,Na)金属负极(< 40 μm)是实现高比能钠金属电池(Sodium metal batteries,SMB)的关键。然而,金属钠较差的加工性严重限制了它的实际应用。因此,本研究提出一种双相互穿增强策略,通过机械捏合工艺制备出厚度在15~40 μm范围内可控的钠/磷化钠-碳纳米管(Na/Na 3 P5-CNT10,NNP5C10)复合箔。红磷(Red phosphorus,RP)与金属钠应压反应原位生成Na 3 P,并与碳纳米管(Carbon nano tube,CNT)均匀分散于钠基体中,共同构筑出Na 3 P-CNT互穿增强的结构。Na 3 P通过抑制位错运动提高复合材料的强度,碳纳米管则通过界面润滑和裂纹桥接作用改善复合材料的塑性变形行为,从而实现复合箔的可控减薄。此外,构建的Na 3 P-CNT结构能够促进离子和电子传输,降低钠沉积成核势垒,进而实现均匀钠沉积。因此,采用30 μm厚的NNP5C10复合电极组装的对称电池在0.5 mA cm −2 电流密度和0.5 mAh cm −2 面积容量条件下稳定循环超过2500小时。20 μm厚NNP5C10复合负极与Na 3 V 2 (PO 4 ) 3 (NVP)正极匹配组装的全电池在0.2C倍率下实现约276 Wh kg −1 的能量密度,负极/正极容量比(Negative-to-positive capacity ratio,N/P)低至约1.9。本研究为高容量超薄钠金属负极的构筑提供了一种有效的策略,从而推动了高比能钠金属电池的发展。