JOURNAL OF POWER SOURCES
·
2021
·
IF 9.127
Yingmin Jin,Xin Zong,Xuebai Zhang,Chaojun Liu,Dong Li,Zhenggang Jia,Gen Li,Xuanguang Zhou,Junhua Wei,Yueping Xiong
Composite solid electrolyte (CSE) consisting of Li + conductive fillers and polymer matrix has become attractive for high energy-density lithium batteries . Current researches focus on the “ceramic in polymer”-type CSE due to the severe agglomeration of ceramic particles. Consequently, the destroyed percolation network impedes the further improvement in ionic conductivity . In this work, we report a novel structural design of ceramic-enriched CSE consisting of three-dimensional (3D) interconnected Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP), polyvinylidene fluoride (PVDF) and LiN(SO 2 ) 2 (CF 3 ) 2 (LiTFSI). The 3D LATP network is constructed through the surface functionalization of LATP particles by polymethyl methacrylate (PMMA). Owing to the intermolecular interaction between PMMA and PVDF, the incorporation of PMMA-coated LATP (denoted as LATP@PMMA) enables the uniform distribution of ceramic phase and generates interconnected LATP network. Noticeably, such an electrolyte maximizes the utilization of inorganic fillers through the facile treatment of zero-dimensional materials, which is comparable to those 3D template-derived fillers. Furthermore, continuous Li + conduction pathways through LATP framework and LATP/PVDF interphase are guaranteed by the enhanced affinity of LATP towards PVDF matrix and the intrinsic Li + complexation capability of PMMA. Remarkable cycling performances of the LiNi 0.5 Co 0.2 Mn 0.3 O 2 /LATP@PMMA-PVDF/Li batteries confirm the feasibility of 3D ceramic-enriched composite electrolyte in the application of solid-state lithium batteries.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2025
·
IF 8.2
Xiangyu Han,Jiaqi Wang,Yongguang Liu,Lei Dai,Ling Wang,Shan Liu
All-solid-state sodium-ion batteries (ASSIBs) with inorganic solid electrolytes can achieve high safety and high energy density when paired with a high-voltage cathode. However, the slow charge transfer and chemical instability between the high-voltage cathode and rigid electrolyte seriously restrict its development. Herein, a high energy density Na4MnCr(PO4)3-based ASSIBs have been achieved by using a simple low-temperature brazing strategy. The in situ generated secondary phase can not only achieve close contact and rapid charge transfer between the Na4MnCr(PO4)3 cathode and electrolyte but also change the interface electric field distribution and reduce interface side reactions effectively. This strategy is simple and easy to implement and has important guidance for the development of other high-energy all-solid-state batteries.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CERAMICS INTERNATIONAL
·
2021
·
IF 4.527
Jingrui Kang,Rui Gu,Xu Guo,Jing Li,Hongchen Sun,Leiyang Zhang,Ruiyi Jing,Li Jin,Xiaoyong Wei
NASICON-type structured compounds Li 1+ x M x Ti 2- x (PO 4 ) 3 (M = Al, Fe, Y, etc.) have captured much attention due to their air stability, wide electrochemical window and high lithium ion conductivity. Especially, Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a potential solid electrolyte due to its high ionic conductivity . However, its actual density usually has a certain gap with the theoretical density, leading the poor ionic conductivity of LATP. Herein, LATP solid electrolyte with series of SnO–P 2 O 5 –MgO (SPM, 0.4 wt%, 0.7 wt%, 1.0 wt%, 1.3 wt%) glass addition was successfully synthesized to improve the density and ionic conductivity. The SPM addition change Al/Ti–O bond and P–O bond distances, leading to gradual shrinkage of octahedral AlO 6 and tetrahedral PO 4 . The bulk conductivity of the samples increases gradually with SPM glass addition from 0.4 wt% to 1.3 wt%. Both SPM and the second-phase LiTiPO 5 , caused by glass addition, are conducive to the improvement of compactness. The relative density of LATP samples increases first from 0 wt% to 0.7 wt%, and then decreases from 0.7 wt% to 1.3 wt% with SPM glass addition. The grain boundary conductivity also changes accordingly. Especially, the highest ionic conductivity of 2.45 × 10 −4 S cm −1 , and a relative density of 96.72% with a low activation energy of 0.34 eV is obtained in LATP with 0.7 wt% SPM. Increasing the density of LATP solid electrolyte is crucial to improve the ionic conductivity of electrolytes and SPM glass addition can promote the development of dense oxide ceramic electrolytes.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2021
·
IF 4.527
Nali Li,Yong Yu,Yanwei Tong,Tiantian Liu,Xuefeng Zhang
An enhanced sol-gel combustion method was used to synthesize different porous Sc 3+ -doped Li 3 V 2-x Sc x (PO 4 ) 3 /C (x = 0.00, 0.05, 0.10 and 0.15) compounds. The substitution of Sc 3+ into the V 3+ sites of Li 3 V 2-x Sc x (PO 4 ) 3 /C expands the lattice volume along with the enlargement of Li + diffusion channel, which is beneficial for Li + transportation and ionic conductivity improvement. Besides, the Sc 3+ doping content exhibits a great impact on the morphology of Li 3 V 2-x Sc x (PO 4 ) 3 /C composite. The pristine Li 3 V 2 (PO 4 ) 3 /C are constituted of porous particles and nanorods , and the ratio of nanorods to particles can be controlled by adjusting the amount of Sc 3+ doping since the ratio of nanorods to particles decreases with increasing Sc 3+ doping content. When Sc 3+ doping content increases to a certain level (x = 0.15, Li 3 V 1.85 Sc 0.15 (PO 4 ) 3 /C), the nanorods are hardly seen. Li 3 V 1.90 Sc 0.10 (PO 4 ) 3 /C with higher tapped density, better reversibility, smaller resistance and larger Li + diffusion coefficient demonstrates outstanding rate performance and cyclic stability, together with high specific discharge capacities of 130.2 and 92.9 mAh g −1 at 0.5 and 20 C, respectively. Furthermore, a superior specific discharge capacity of 85.8 mAh g −1 was retained at 20 C following 1000 cycles. Overall, a novel approach for the preparation of high-performance Li 3 V 2-x Sc x (PO 4 ) 3 /C cathodes with different morphologies for lithium-ion batteries is provided.
✓ 已验证
DOI
高影响因子
Inorganic Chemistry Frontiers
·
2018
·Vol. 5
·期 3
·619-625
·
IF 5.106
Ying Liu,Maxim S. Molokeev,Quanlin Liu,Zhiguo Xia
Crystal structure evolution and temperature-dependent phase transition of solid solutions are much desired for the understanding of the optimization of functional properties. Herein, the NASICON-type NaZr2(PO4)3–SrZr4(PO4)6 solid solutions with the formula Na(2−2x)Srx[ ]xZr4(PO4)6 (0 ≤ x ≤ 1), where [ ] represents the vacancy, were prepared by the sol–gel method, and their crystal structures, phase transitions and thermal expansion properties were investigated in detail. In the range of x = 0.3–0.35, there is a reversible structural phase transition Rc ↔ R and the different structural models of the R phase and Rc phase were built to better understand the phase transition mechanism. We determined the phase transition boundary between the Rc and R structures and predicted the phase transition temperature of Na(2−2x)Srx[ ]xZr4(PO4)6 with any x for further investigation of controlled physical properties. The results indicated that Na0.5Sr0.75[ ]0.75Zr4(PO4)6 showed a near zero thermal expansion in the temperature range of 450–600 K, which can find potential applications.
✓ 已验证
DOI
高影响因子
IONICS
·
2023
·Vol. 29
·期 6
·2271-2285
·
IF 2.8
Yan Ji,Zhu Jiuzhou,Zhang Libo,Li Yan,Wang Heng,Wang Lizhen
Lithium-sulfur batteries present a promising potential in meeting the demand of high energy and low-cost energy storage system. However, it suffers from the severe shuttle effect of lithium polysulfides and sluggish sulfur chemistry kinetics. Herein, NASICON-type ceramic material Na 3 V 2 (PO 4 ) 3 is developed to decorate on polypropylene (PP) membrane as a catalysis layer to adsorb lithium polysulfides and accelerate the conversion of sulfur electrochemistry redox reaction. Meanwhile, the sophisticated architecture on separator provides additional lithium ion intercalaction-extraction behavior, which helps to hamper the shuttle effect of lithium polysulfides. The collaborative contribution of above virtues endows the Li–S batteries with excellent capacitive performance of 1045.3 mA h g −1 at 0.2 C current density, superior rate capability (590.4 mA h g −1 ) at 4 C although the cycling stability over 400 cycles at 4C is still needed to improve. This work offers an elaborate ceramic coating layer engineering on separator to act as an electro-catalyst role to improve the conversion reversibility and kinetics in lithium sulfur battery with high-energy.
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2024
·Vol. 53
·期 4
·1849-1861
·
IF 3.5
Haodi Dong,Changcheng Liu,Que Huang,Yanjun Chen
Nowadays, the poor conductivity and unstable structure have become obstacles for the popularization of Na3V2(PO4)3 (NVP). In the current work, a dual-modified Mn0.1Cl0.3-NVP composite doped with Mn and Cl is prepared by a facile sol–gel method. When Mn2+ with a large ionic radius replaces small V3+, it can improve the stability of the NVP crystal structure. In addition, the replacement of V3+ by Mn2+ in a low valence state can generate redundant hole carriers, which is conducive to the rapid transport of electrons. The substitution of PO43− by Cl−, which is more electronegative, can reduce the impedance and facilitate the movement of Na+. Owing to the synergistic effect of Mn and Cl co-substitution, the structural stability of NVP was systematically enhanced, and the electron transfer and ion diffusion were effectively improved. Consequently, the optimized Mn0.1Cl0.3-NVP sample demonstrated superior electrochemical performance and kinetic properties. It exhibited a high reversible capacity of 109.2 mA h g−1 at 0.1C. Even at 15 and 30C, high discharge capacities of 70.3 mA h g−1 and 68.2 mA h g−1 were observed after 2000 cycles with capacity retention above 80%. Moreover, it delivered remarkable capacities of 77.1 and 73.4 mA h g−1 at 100 and 200C with retained capacity values of 50.3 and 47 mA h g−1, respectively, after 2000 cycles. Furthermore, the assembled Mn0.1Cl0.3-NVP//HC full cell delivered a high value of 94.7 mA h g−1 and lit LED bulbs, indicating its excellent application potential.
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2025
·
IF 9.5
Junyu Chen,Xuedong Zhang,Feixiang Wu,Long Xie,Feng Li,Nina Wu,Zixuan Cao,Jinwen Zhao,Yuxuan Zhang,Xin He,Hongxia Gu,Jianyu Huang,Qiao Huang
Integrating conversion-type cathodes (such as iron-based fluorides (IBFs)) into sulfide all-solid-state batteries (ASSBs) significantly enhances energy density but faces challenges including unstable cathode/electrolyte interfaces. To mitigate these issues, a near-amorphous Li1.26Mg0.12Zr1.86(PO4)3 (LMZP) coating technology is developed to protect nano-sized FeF2 (n-FeF2) and micro-sized FeF3 (m-FeF3) cathodes from reacting with the sulfide electrolyte for the first time. The LMZP coating approach offers simplicity, low energy consumption and scalability. With the LMZP-coated cathodes and lithium–indium (Li–In) anode, the ASSBs achieve a discharge capacity of 310 mAh g−1 after 600 cycles and a maximum areal capacity of 2 mAh cm−2 for n-FeF2, and 301 mAh g−1 after 700 cycles with a maximum areal capacity of 3.1 mAh cm−2 for m-FeF3. When using a lithium (Li) metal anode, the ASSBs maintain a discharge capacity of 310 mAh g−1 after 300 cycles for n-FeF2 and 300 mAh g−1 after 600 cycles for m-FeF3, demonstrating excellent cycling stability and capacity retention. Notably, a discharge capacity of 280 mAh g−1 is sustained after 200 cycles for n-FeF2 and 301 mAh g−1 after 180 cycles for m-FeF3, with a reduced stack pressure (10 MPa). These results are unprecedented in IBF-based ASSBs, highlighting the potential of advanced coating strategies to enable scalable, high-performance metal fluoride cathodes in ASSBs with higher energy densities.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Junyan Zhang,Jiaqi Shen,Haomin Chu,Yingchun Xie,Zhenzhen Jiang,Daolin Gao,Tianlong Deng,Xiaoping Yu
With the rapid development of the new energy industry, the recovery or extraction of lithium from different resources is currently a global research hotspot. In this work, Li 3 V 2 (PO 4 ) 3 was used as the active component for electrochemical extraction of lithium from aqueous solutions. The results showed that although Li 3 V 2 (PO 4 ) 3 exhibited the reversible de-intercalation/intercalation of Li + , it suffered from severe irreversible dissolution loss in aqueous solutions. This problem was successfully solved by titanium doping. The experiments and DFT calculations showed that when the V(2)-site vanadium in Li 3 V 2 (PO 4 ) 3 was replaced by titanium, the resulting material exhibited superhigh cycle stability and lithium extraction rate. After ten cycles of de-intercalation/intercalation, the extraction capacity still reached 11.5 mg·g −1 , and the attenuation was within the error range. Particularly, because of the decrease of the band gap after doping, the electronic conductivity of the material was significantly improved, and the equilibrium time for lithium extraction was within only 5 min, which was more than 10 times faster than that of the conventional LiFePO 4 and Li 2 MnO 4 materials. This work provides a new solution for the green, efficient, and highly stable extraction of lithium from liquid lithium resources.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2025
·
IF 9.8
Jicong Zhang,Luwei Shi,Sheng Fei Zhao,Yan Lin,Tao Hu,Ulla Lassi,Ruguang Ma,Chang Ming Li
Na 4 MnV(PO 4 ) 3 is a typical Na-super-ionic-conductor (NASICON), which shows great promise as cathode material for high-performance cost-effective sodium ion batteries. However, sluggish Na + diffusion kinetics coupling with Jahn-Teller effect severely deteriorate its high-rate capability and long-term stability. In this work, we report a regulation strategy of jointly doping dual heteroatoms (Fe and Ni) to realize structural stability of Na 4 MnV(PO 4 ) 3 by shortening bond length and fast ion diffusion. The FMVN electrode delivers a highly reversible capacity of 98 and 79 mAh g −1 at 0.1C and 10C, respectively, while maintaining a stable cycling life over 2000 cycles at 10C. Theoretical calculations and kinetic analysis unveil that the regulation of crystal structure by Fe and Ni joint substitution effectively reduces the Na + migration barrier and simultaneously increases the reversible capacity. Additionally, in-situ x-ray diffraction investigation verifies reversible structure evolution and minor volumetric change (∼4.91 %) in the sodiation/desodiation process. An assembled full cell (FMVN||HC) demonstrates an energy density of 353.9 Wh kg −1 at 0.1C and outstanding cycling durability with 89 % capacity retention after 100 cycles at 2C. This dual substitution strategy in this work holds great promise to develop high-performance NASICON-type cathodes for practical applications.
✓ 已验证
DOI
高影响因子
Materials Science and Engineering B-Advanced Functional Solid-State Materials
·
2016
·
IF 2.331
B.Y. Huang,B.L. Feng,L. Luo,C.L. Han,Y.T. He,Z.R. Qiu
Novel Sr 3 Y(PO 4 ) 3 :Dy 3+ , Eu 3+ (SYP:Dy 3+ , Eu 3+ ) phosphors were synthesized by a standard solid-state reaction under an ambient air atmosphere and their structural and optical properties were investigated. XRD and diffuse reflectance spectra (DRS) were used to explore structural properties. The former showed that single phase phosphors were obtained and that the rare earth ions entered into the cubic host by substituting the smaller Y 3+ ions and thereby enlarging the unit cell. The DRS indicated that the host has a direct bandgap of 4.5 eV. Under 393 nm excitation, a strong and stable warm white light emission with high color purity was achieved in SY 0.92 P:0.06Dy 3+ , 0.04Eu 3+ . The energy transfer from Dy 3+ to Eu 3+ ions was investigated and the related mechanism was discussed based on the optical spectra and emission decay curves. The thermal quenching of emission is similar to that of YAG:0.06Ce 3+ . The results show the single phase phosphor is potential in warm white LED.
✓ 已验证
DOI
高影响因子
SOLID STATE IONICS
·
2024
·
IF 3
Shengping Deng,Chongran Song,Shiyu Li,Ying Bai
NASICON-type Na 4 MnCr(PO 4 ) 3 (NMCP) has gained significant attention due to its prominent capacity and voltage platform. However, poor intrinsic electron conductivity severely obstructed its wider application. Here, the NMCP was decorated through structurally integrated with the high conductive carbon nanotubes (CNTs) component via the sol-gel method. The CNTs additive was tightly implanted NMCP bulk, providing fast electron transfer rates, further reduced charge transfer resistance and ohmic resistance , and improving the electrochemical properties of NMCP during the reversible intercalation/deintercalation of Na + . Finally, the as-prepared rambutan-like NMCP/C@CNTs could release a high reversible capability of 118.7 mAh g −1 at 0.1C and exhibit long durability over 500 cycles at a high rate of 10C. The pseudocapacitance contributions were investigated, and the Na storage mechanism was also demonstrated through in-situ synchrotron X-ray diffraction. The assembled NMCP/C@CNTs//HC full cell could deliver a high energy density of 364.4 Wh kg −1 . The encouraging electrochemical performance of the full cell will promote the development of sodium ion secondary batteries for large-scale applications in the future.
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）