PHYSICA STATUS SOLIDI A-APPLICATIONS AND MATERIALS SCIENCE
·
2024
·Vol. 221
·期 16
·2400342
·
IF 1.9
Jian Cheng,Xin Liu,Weichang Kong,Qingzheng Lei,Zhiyu Yu,Dun Liu
The fabrication of flexible electronics has gained extensive attention due to the growing demand of flexible devices. Among various methods, laser direct writing technology has emerged as a promising approach due to its advantages of high processing accuracy and simplicity. This research focuses on the preparation of copper microelectrodes using laser-induced reduction of CuO nanoparticles (Cu NPs) on polyethylene terephthalate films. First, the influence of various parameters on the conductivity of the copper microelectrodes is investigated. Second, flexible copper microelectrodes with a minimum resistivity of 62.29 μΩ cm and an adhesion grade of 4B level are successfully fabricated. Building upon these results, a capacitive pressure sensor is developed with optimal sensitivity of 3.99 Pa −1 , good hysteresis of 3.99%, and response and recovery times of 1.2 and 1.3 s, respectively. Repeatability tests confirm the sensor's stability and fatigue resistance. This research provides valuable insights for the production of flexible sensors.
研究领域:
生物医学工程
·
柔性电子学
·
传感器技术
·
纳米材料
·
微纳加工
·
可穿戴设备
✓ 已验证
DOI
高影响因子
APPLIED MICROBIOLOGY AND BIOTECHNOLOGY
·
2019
·Vol. 103
·期 14
·5907-5916
·
IF 3.67
Qiu Yongting,Wang Zhihong,Liu Feng,Liu Junxia,Tan Kaiting,Ji Ruibo
Allelopathy by hydrophytes can be utilized to control algal blooms. This study was conducted to investigate the allelopathic effect (inhibition) of Scenedesmus quadricauda on Microcystis flos-aquae . When M. flos-aquae was co-cultured with S. quadricauda , the secretion of high-MW biopolymer by M. flos-aquae was inhibited by S. quadricauda . We further identified the allelochemicals and found that 4-tert-butylpyrocatechol (TBC) was the main active ingredient that could inhibit the growth of M. flos-aquae . When the dose of TBC was larger than 0.2 mg/L, almost all of the M. flos-aquae died. Additionally, TBC was found to suppress the growth of M. flos-aquae by disturbing the synthesis and secretion of proteins and polysaccharides and harming the chlorophyll to affect the light harvesting of algal cells. Therefore, TBC has the potential for use as a potential and promising algaecide to restrain the biomass of M. flos-aquae .
研究领域:
水生生物学
·
环境微生物学
·
化学生态学
·
藻类生理学
·
生物防治
✓ 已验证
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2022
·Vol. 47
·期 5
·2556-2564
·
IF 3.925
Juan-Juan Shao,Jian-Ling Ni,Wei-Min Chen,Peng-Lai Liu,Abraham Mensah,Li-Zhuang Chen,Fang-Ming Wang
As a luminescent material with excellent structural diversity and optical tunability, cuprous iodide organic–inorganic hybrid semiconductors have attracted extensive attention in the field of environmental friendly solid-state lighting (SSL). In order to systematically study how tiny changes in ligands influence the luminescence properties of their complexes, in this study, the tail atoms of ethyl groups in ligands are modified with halogen atoms (F, Cl, and Br) and four all-in-one (AIO)-structured cuprous iodide inorganic–organic hybrid semiconductor materials (Cu2I4(Ln)2) are successfully obtained. The adjustment of the tail atoms effectively regulated the stacking modes of Cu2I42− clusters and their luminescence properties, realizing the transition of the crystal luminescence color from blue to green with the internal quantum yield (IQY) increasing from 1.57% to 53.39%. Their optical diffuse reflectance spectra and density functional theory calculations (DFT) helped investigate the origin and mechanism of luminescence. They are very stable and have good solution processability, which means that they can be applied as rare-earth element-free lighting phosphors. This study can provide ideas and a theoretical basis for designing cuprous iodide cluster luminescent materials in future.
研究领域:
材料科学
·
无机化学
·
光电子学
·
半导体物理
·
发光材料
·
计算化学
✓ 已验证
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2011
·
IF 3.37
Min Sun,Bin Ding,Jianyong Yu,You-Lo Hsieh,Gang Sun
A highly sensitive coating comprising 3-mercaptopropionic acid (MPA) monolayer modified electrospun polystyrene (PS) membranes was constructed on the electrode of quartz crystal microbalance (QCM) for Cu 2+ detection. The three-dimensional fibrous PS membranes with high specific surface area (SSA) were deposited on the electrode of QCM via electrospinning. The PS membranes were sputter coated with gold, then modified with self-assembled monolayer of MPA. The PS-MPA sensors showed fast response (2–3 s) to Cu 2+ and a detection limit down to 100 ppb. Additionally, sensor sensitivity increased concurrently with both increasing PS loading and SSA on QCM electrodes . The response of the PS-MPA sensors with a PS membrane loading of 978 Hz and SSA of 43.31 m 2 /g was 40 times larger than that without membranes when exposed to 1 ppm of Cu 2+ . The sensor responses were reproducible toward Cu 2+ in the 100–5 ppm concentration range, whereas a linear response was found in the 100–1 ppm concentration range. The sensor response to Cu 2+ showed a linear relationship with an increase in pH from 2 to 7. Moreover, the sensors also exhibited chelation selectivity for other transition metal ions in the descending order Cu 2+ > Ni 2+ > Zn 2+ > Fe 2+ at concentration between 1 and 5 ppm.
研究领域:
分析化学
·
环境监测
·
材料科学
·
生物传感器
·
纳米技术
·
重金属检测
·
表面功能化
✓ 已验证
DOI
高影响因子
Journal of Energy Chemistry
·
2018
·
IF 3.886
Yunfeng Bao,Chunlei Huang,Limin Chen,Yu dong Zhang,Long Liang,Jinjun Wen,Mingli Fu,Junliang Wu,Daiqi Ye
Anatase TiO 2 nanosheets (-ns-) with dominant exposed {001} facets were used as support to load copper, and the synthesized Cu/TiO 2 -ns catalysts were evaluated for CO 2 hydrogenation to methanol. Under the reaction conditions, P = 3.0 MPa, T = 260 °C, V (N 2 ): V (H 2 ): V (CO 2 ) = 8:69:23 and gas hourly space velocity (GHSV) = 3600 mL g −1 h −1 , the methanol yield reached an appealing high value, 5.6%. Copper-loading amount, calcination temperature and reduction atmosphere have been investigated in this work, which significantly influence the particle sizes of copper and/or the defect concentration in TiO 2 , then leading to different catalytic performance. Characterizations of XRD, EPR, CO 2 -TPD and FTIR demonstrate that higher specific surface area of Cu is good for the hydrogenation of CO 2 and adequate amount of Ti 3+ plays important roles in CO 2 activation. Both of them facilitate high turnover frequency (TOF) of methanol formation.
研究领域:
催化化学
·
能源化学
·
材料科学
·
环境科学
·
工业催化
·
表面科学
·
纳米材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2023
·
IF 9.2
Zhongshuai Zhang,Yuqing Liu,Zixi Liu,Hailin Li,Yaoliang Huang,Weijian Liu,Dingshan Ruan,Xin Cai,Xiaoyuan Yu
O3-type Fe/Mn-based layered oxides are considered as the competitive cathode materials for sodium-ion batteries because of environmental friendly metal elements and low cost. However, a lower capacity, poor cycling stability and irreversible phase transitions hinder their commercial application. Herein, the Cu-doped O3 biphasic Na[Mn 0.6 Fe 0.4 ] (1- x ) Cu x O 2 (NFMCu- x ) layered oxides are successfully synthesized by high temperature calcination using Fe/Mn-based Prussian blue analogues as precursor. The results indicate that the different stoichiometric of Cu 2+ substitution in P2 NaMn 0.6 Fe 0.4 O 2 can cause the transformation of P2 phase to O3 monophase or O3 biphase. The NFMCu- x samples exhibit O3 monophase at x = 0.1, 0.15, while O3 biphase coexists in the compound at x = 0.2, 0.25, and 0.3. Benefiting from the synergetic effect of Cu-doping and O3 biphasic structure, the optimized O3 biphasic NaMn 0.48 Fe 0.32 Cu 0.2 O 2 exhibits a high Na + diffusion coefficient and an excellent sodium storage performance with a high discharge specific capacity of 103.76 mAh g −1 at 24 mA g −1 and good capacity retention of 82.9% after 100 cycles. Moreover, Cu-doped O3 biphasic NaMn 0.48 Fe 0.32 Cu 0.2 O 2 features an excellent air stability. Thus, this work proposes a strategy in development of O3 Fe/Mn-based layered oxide as high-performance cathode materials for sodium-ion batteries.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
固态化学
✓ 已验证
DOI
高影响因子
RSC Advances
·
2015
·Vol. 5
·期 78
·63866-63873
·
IF 3.84
Yujie Qiang,Shengtao Zhang,Shenying Xu,Linliang Yin
The inhibition effect of 5-nitroindazole on the corrosion of copper in a 3.0% NaCl solution was investigated with the methods of weight loss, electrochemical tests, scanning electronic microscopy (SEM) and theoretical calculations. The weight loss and electrochemical results revealed that 5-nitroindazole is a mixed-type inhibitor with the inhibition efficiency is up to 99% at 0.4 mM, which was further confirmed by SEM observation. The adsorption of the inhibitor molecule on the copper surface was found to obey the Langmuir adsorption isotherm. The quantum chemical calculations and molecular dynamics simulation showed that 5-nitroindazole is adsorbed strongly on the copper surface in a parallel mode through the indazole ring.
研究领域:
材料科学
·
腐蚀与防护
·
物理化学
·
表面科学
·
电化学
·
金属材料
·
理论化学
✓ 已验证
DOI
高影响因子
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2023
·Vol. 30
·期 46
·102880-102893
·
IF 5.8
Li Yunhe,Li Hao,Zhao Baogang,Ma Yanming,Liang Peiyuan,Sun Tianjun
The escalating levels of surface ozone concentration pose detrimental effects on public health and the environment. Catalytic decomposition presents an optimal solution for surface ozone removal. Nevertheless, catalyst still encounters challenges such as poisoning and deactivation in the high humidity environment. The influence of support on catalytic ozone decomposition was examined at a gas hourly space velocity of 300 L·g −1 ·h −1 and 85% relative humidity under ambient temperature using Cu-Mn–doped oxide catalysts synthesized via a straightforward coprecipitation method. Notably, the Cu-Mn/SiO 2 catalyst exhibited remarkable performance on ozone decomposition, achieving 98% ozone conversion and stability for 10 h. Further characterization analysis indicated that the catalyst’s enhanced water resistance and activity could be attributed to factors such as an increased number of active sites, a large surface area, abundant active oxygen species, and a lower Mn oxidation state. The catalytic environment created by mixed oxides can offer a clearer understanding of their synergistic effects on catalytic ozone decomposition, providing significant insights into the development of water-resistant catalysts with superior performance. Graphical
研究领域:
环境催化
·
大气污染控制
·
材料化学
·
表面科学
·
催化化学
·
环境工程
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2016
·
IF 6.333
Yanchun Yang,Xiaojiao Kang,Lijian Huang,Song Wei,Daocheng Pan
Earth abundant Cu 2 ZnSn(S,Se) 4 (CZTSSe) has been considered as one of the most promising thin film solar cell absorber candidates. Here, we develop a facile water-based precursor solution approach for depositing high-efficiency Cu 2 ZnSn(S,Se) 4 thin film solar cells. In this environmentally friendly approach, inexpensive elemental Cu, Zn, Sn and S powders are used as the starting materials and are dissolved in the aqueous solution of thioglycolic acid and methylamine, forming a homogeneous precursor solution for depositing Cu 2 ZnSnS 4 nanocrystal thin film . As-deposited CZTS nanocrystal thin films are selenized to form the large-grain CZTSSe absorber layers . It was found that Na doping plays an important role in the formation of the extremely dense and flat CZTSSe absorber layer, and fill factor can be significantly improved for Na-doped CZTSSe solar cells, which lead to a photoelectric conversion efficiency of 6.96% with an open-circuit voltage of 378 mV, a short current density of 28.17 mA cm −2 , and a fill factor of 65.4%.
研究领域:
材料科学
·
新能源材料
·
半导体薄膜
·
光伏技术
·
无机功能材料
✓ 已验证
DOI
高影响因子
MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING
·
2021
·
IF 3.927
Nengyuan Zeng,Chenwei Wang,Chong Luo,Hongdong Zhao,Yuling Liu,Wantang Wang,Tengda Ma
This article proposed an improvement plan for the slurry to reduce the dishing caused during copper chemical mechanical polishing (CMP) of the interconnect structure. According to the difference in the pressure between the concave and convex parts of the copper film in the high-hardness polishing pad, polishing slurries were designed with a distinct difference in the polishing removal rate under high and low platen pressures to improve their planarization efficiency. 2 wt% GLY (glycine) and 1 wt% H 2 O 2 can provide a chemical dissolution effect, adding 0.1% TAZ (1,2,4-triazole) to slow down the corrosion mainly for the recession, by adjusting the slurry pH to 7. The polishing results showed that the slurry had a high copper removal rate (6772 Å/min) at high pressure (3.0 psi) and a much lower removal rate (3273 Å/min) at low pressure (1.2 psi). The pattern wafer polished with this slurry obtained relatively low dishing. The other comparison groups showed slight differences in copper removal rate at high and low pressure and a deeper dishing of the polished pattern wafer. In this paper, based on the analysis of static dissolution experiments, electrochemical experiments, and XPS experiments of copper films in different slurries, the chemical reaction mechanism of copper films in the solution system of GLY and H 2 O 2 was studied at different pH values. In addition, the inhibition mechanism of TAZ on the copper surface at different slurry pH values was proposed, including the properties of the TAZ molecule adsorption film on the copper surface, the uniformity of the surface coverage, and the thickness of the passivation layer . The results can reflect the polishing results to a certain extent despite some deviations, but it can also be used as a more reasonable argument to explain the optimization scheme of the slurry proposed in this article.
研究领域:
材料科学
·
微电子制造
·
表面化学
·
半导体工艺
·
腐蚀与防护
✓ 已验证
DOI
高影响因子
PROPELLANTS EXPLOSIVES PYROTECHNICS
·
2024
·Vol. 50
·期 3
·e202400232
·
IF 1.7
Bo Hao,Caixian Xu,Geng Chen,Yuangen Lu,Li Zhang
In response to issues such as poor accuracy and unstable delay times encountered in the practical use of tungsten-based delay compositions, an analysis of the combustion performance of tungsten-based delay compositions with the addition of copper oxide was conducted. This study selected five tungsten-based composite delay compositions prepared by blending tungsten-based delay compositions with copper oxide at different content, aiming to investigate the influence of varying copper oxide proportions on the combustion characteristics of tungsten-based delay compositions. Microscopic morphologies and thermal decomposition behaviors of the tungsten/copper oxide delay compositions were analyzed using scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), while combustion products were examined by X-ray diffraction (XRD). The results indicate that copper oxide exerts a strong catalytic decomposition effect on tungsten-based delay compositions. Specifically, a low concentration of copper oxide enhances the combustion rate of tungsten-based delay compositions, while an increase in copper oxide content subsequently slows down the combustion rate. Notably, tungsten-based delay compositions with 9% copper oxide content demonstrate high precision, good stability, and a relatively slow combustion rate, offering a wider range of adjustability for controlling the combustion speed of delay compositions and providing a feasible method for managing the delay time range in practical applications.
研究领域:
材料科学
·
火工品技术
·
燃烧学
·
无机化学
·
功能材料
✓ 已验证
DOI
高影响因子
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
·
2021
·
IF 5.234
Siqi Xiang,Xingjian Du,Yihan Liang,Mengcheng Zhou,Xinfang Zhang
Full density TiC reinforced Cu matrix composites are fabricated by electropulsing-assisted flash sintering within 40 s. The addition of TiC significantly increases the hardness of the sintered sample. However, liquid Cu does not wet stoichiometric TiC, leading to a poor interface bonding strength between TiC and Cu, thus the tensile strength of the sintered sample is destroyed. By adding a small amount of Ti, the bonding strength of the interface between TiC and Cu can be effectively optimized, thereby the mechanical strength of the samples is improved, showing an increased hardness and tensile strength . Skillfully use the relationship between hardness and tensile strength curve to intuitively show the bonding strength of the micro interface from the macro characteristics. The reaction between dissolved Ti and stoichiometric TiC and the decomposition of stoichiometric TiC cause the formation of near-surface non-stoichiometric TiC x ( x < 1) with a marked metal-like electronic structure, which is the fundamental reason for the optimization of the interface bonding between TiC particles and Cu matrix. In the process of powder metallurgy , it is a promising strategy to enhance the composite materials by adjusting the stoichiometry of ceramic to form metal-like electronic structure and alter the bonding strength of ceramic/metal interface.
研究领域:
材料科学
·
粉末冶金
·
金属基复合材料
·
界面工程
·
固态加工
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）