CERAMICS INTERNATIONAL
·
2025
·
IF 5.6
Xinyu Ping,Xiaoyu Pan,Bin Meng,Qingqing Yang,Wenlong Zhang
The dielectric performance of BaTiO 3 -based ceramic capacitors must be improved for further miniaturization and integration of energy storage devices. This study combines two optimization strategies, the grain refinement and high-entropy effect, to design BaTiO 3 -based high-entropy nanocrystalline ceramics: Ba(Ti 0.2 Zr 0.2 Nb 0.2 Y 0.2 Sn 0.2 )O 3 (HEO1) and Ba(Ti 0.2 Zr 0.2 Nb 0.2 Yb 0.2 Hf 0.2 )O 3 (HEO2). These ceramics were synthesized using fast hot-pressing sintering (FHPS), yielding HEO1-FHPS and HEO2-FHPS samples, both of which exhibit a pure perovskite structure, similar to that of samples fabricated via conventional solid-state sintering (CS), namely HEO1-CS and HEO2-CS. The relative densities of the HEO1-FHPS (96.18 %) and HEO2-FHPS (98.34 %) samples are higher than those of HEO1-CS (95.47 %) and HEO2-CS (95.40 %). In addition, the grain sizes of HEO1-FHPS (0.092 μm) and HEO2-FHPS (0.084 μm) are notably smaller than those of HEO1-CS (2.48 μm) and HEO2-CS (2.91 μm). The high relative density and small grain size of HEO1 and HEO2 improve their maximum permittivity, increase the Curie temperature and enhance dielectric stability. Furthermore, compared with HEO1-CS and HEO2-CS, HEO1-FHPS and HEO2-FHPS exhibit higher critical electric field strengths (359 and 389 kV/cm), greater recoverable energy densities (0.40 and 0.88 J/cm 3 ) and improved energy storage efficiencies (69.6 % and 70.4 %). These findings provide a promising approach for developing BaTiO 3 -based ceramics with enhanced dielectric performance.
研究领域:
材料科学
·
电子工程
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2023
·
IF 9.5
Yan Zhong,Jiaqi Wang,Longgang Wu,Kunshan Liu,Shengping Dai,Jing Hua,Guanggui Cheng,Jianning Ding
A microstructured surface has been applied in self-powered triboelectric pressure sensors to increase the charge-carrying sites and enhance the output performance. However, the microstructure increases the distance between the electrode and the triboelectric layer, and its influence on the output performance is unknown. Herein, we proposed a dome-conformal electrode strategy for a self-powered triboelectric nanogenerator (TENG) pressure sensor. With a simple reverse-dome adsorption process, an ultrathin triboelectric layer and Ag electrode can be made conformal to the dome PDMS structure. The TENG sensor is constructed with paper as a positive triboelectric layer. Compared with the device based on nonconformal structure, the conformal design strategy endows the device with a faster charge transfer and enhanced output voltage. By doping with BaTiO3, the outermost triboelectric layer can be easily modified to improve its ability of sustaining charge, and an ultrathin PDMS layer is coated on the triboelectric layer to expand the triboelectric polarity difference between two triboelectric layers so as to enhance the output voltage. The synergistic effects enable the optimized TENG sensor with a sensitivity of 0.75 V/kPa in the low-pressure region (0–26 kPa) and 0.19 V/kPa in the high-pressure range (26–120 kPa). Its application in human motion detection, grabbing water beakers, and noncontact distance testing has been demonstrated. This work provides a route such as a conformal structure design strategy to enhance the output performance of a microstructure-based TENG sensor.
研究领域:
材料科学
·
传感器技术
✓ 已验证
DOI
PubMed
高影响因子
COMPOSITES SCIENCE AND TECHNOLOGY
·
2018
·
IF 5.16
Hang Luo,Zhong Wu,Xuefan Zhou,Zhongna Yan,Kechao Zhou,Dou Zhang
Carbon nano-materials e.g. graphene are widely utilized to prepare high-к dielectrics due to their low percolation threshold. However, composites incorporated with conductive carbon nano-materials usually suffer from high dielectric loss. In this work, a strategy is proposed to suppress the dielectric loss of graphene/P(VDF-HFP) composites using two-dimensional BaTiO 3 platelets. Large interfacial region is formed in the composites due to the hybrid fillers , which results with enhanced interfacial polarization . The BaTiO 3 platelets are aligned in the perpendicular direction to the surface of the composite film after the treatment of tape casting . These aligned BaTiO 3 platelets act as isolation belts to block the electron transportation path. In these contributions, composite with a high permittivity of 66.2 and suppressed dielectric loss of 0.048 are simultaneously obtained. This work provide a feasible route to prepare high performance dielectric composites.
研究领域:
材料科学
·
电子工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2016
·Vol. 28
·期 5
·4204-4210
·
IF 1.798
Huang Xuechen,Zhang Wenqin,Xie Juan,Xu Qi,Zhang Lin,Hao Hua,Liu Hanxing,Cao Minghe
Nb 2 O 5 doped 0.8BaTiO 3 –0.2(Na 1/4 Bi 3/4 )(Mg 1/4 Ti 3/4 )O 3 (0.8BT–0.2NBMT) polycrystalline ceramics were prepared by solid state reaction method. 0.8BT–0.2NBMT samples were observed to possess two dielectric peaks, which were attributed to the formation of core–shell structure (Huang et al. in J Eur Ceram Soc 36:533–540, 2015 ). Longer sintering induced uniform distributions of the additives. The introduction of Nb 2 O 5 into 0.8BT–0.2NBMT could obviously bring about the improvement of the dielectric temperature stability, the degradation of the dielectric loss at room temperature and the decrease of the sintering temperature. The 0.8BT–0.2NBMT ceramics doped with 2.0 at% Nb 2 O 5 could satisfy the temperature range of the X9R (−55 to 200 °C, △C/C 25°C = ±15% or less) characteristics, with a moderate dielectric constant of 1130, low dielectric loss of 0.7%, low sintering temperature of 1050 °C and insulation resistivity of 5 × 10 12 Ω cm at room temperature, which might be promising for practical use in multilayer ceramic capacitors. The inhomogeneous distribution and the existence of the secondary phases were responsible for this excellent dielectric temperature characteristic. The complex impedance analysis was introduced to elaborate the conduction mechanism.
研究领域:
材料科学
·
电子工程
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2024
·
IF 8.1
Jin-Jian Pan,Jia Huang,Yuan-Hang Qin,Zhen Chen,Li Yang,Cun-Wen Wang,Xingmao Jiang
Ba-based perovskite oxides rich in oxygen vacancies (OVs) are anticipated to possess robust electron-donating capabilities and other favourable properties, rendering them a promising support for Ru catalysts in NH 3 synthesis. Herein, a glucose-urea deep eutectic solvent calcinating method was developed to synthesize an OV-rich BaTiO 3 (BTO-H) support for Ru catalysts. The BTO-H-supported Ru (Ru/BTO-H) catalyst achieves an impressive NH 3 synthesis rate of 5133 μmol g cat –1 h −1 (256.7 mmol g R u –1 h −1 ) at 400 °C and 0.1 MPa, surpassing the performance of Ru catalysts supported on OV-poor BTO supports and other supported Ru catalysts. Physical characterizations and kinetic experiments reveal the multifaceted influence of OVs on enhancing the catalytic performance of Ru/BTO-H in NH 3 synthesis. OVs serve as electron donors to Ru catalyst, facilitating the activation and dissociation of N 2 . Simultaneously, OVs act as hydrogen acceptors from the Ru surface, mitigating hydrogen poisoning effects. Additionally, OVs stimulate the formation of surface hydrides, not only providing active sites for N 2 activation but also bestowing an electron-donating effect on the supported Ru catalyst. The combined positive effects of OVs establish BTO-H as an outstanding support for Ru catalysts in NH 3 synthesis.
研究领域:
材料科学
·
催化化学
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2022
·
IF 5.532
Zhiqiang Li,Shiguang Yan,Jiake Xia,Fei Cao,Xuefeng Chen,YunXiong Song,Yonghong Chen,Zhi-Sheng Lin,Genshui Wang
With the increasing demand for the miniaturization, high capacitance and high reliability of the Multilayer Ceramic Capacitor (MLCC), the thickness of single dielectric layer is less than 1 μm and the original partical size of the powder has reached the scale less than 300 nm. In this paper, BaTiO 3 powder of various partical sizes (150–500 nm) was modified with Dy and Ho through a chemical coating method. The dense and uniform ceramics in accordance with EIA X7R-type temperature stability were sintered under low oxygen partial pressure and good dielectric properties of dielectric constant >2000 and dielectric loss <1% were obtained. The grain size effect on the dielectric properties under various dc-bias field were systematically investigated. It is found that the fine-grain ceramic exhibits a lower absolute change of the dielectric constant and a higher dc-bias stability. Furthermore, the modified 150 nm BaTiO 3 powders was made into 1210-type MLCCs, and the dielectric behavior of the MLCCs with different dc-fields and ac-fields were study over −55 °C–125 °C. It is found that the ac electric field had a greater influence on the dielectric properties at room temperature and below, and the dielectric constant variation under a dc-bias field was also greatly advanced for the modified fine-grain MLCCs. The results provide a reference for the design of the next generation of BME-MLCCs.
研究领域:
材料科学
·
电子工程
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2024
·Vol. 35
·期 6
·1-12
·
IF 2.8
Tang Lanxin,Li Shuangchi,Wang Fang,Chen Yu
The binary perovskite-type compound (1 − x )BiFeO 3 – x BaTiO 3 (BF-BT) is considered as a promising high-temperature lead-free piezoelectric material due to its high Curie temperature ( T C > 400 °C) and better electromechanical properties. In this work, ternary lead-free piezoelectric ceramics with a chemical formula of (0.67 − x )BiFeO3–0.33BaTiO3– x Bi(Zn0.5Ti0.5)O 3 + 1 mol% MnO 2 (where x = 0–0.05) were prepared by the conventional solid-state reaction route. The effects of Bi(Zn 0.5 Ti 0.5 )O 3 introduction on the phase structures and microstructures, piezoelectric and dielectric properties, as well as impedance characteristics of BF-BT ceramics were investigated in detail. Firstly, all the samples synthesized exhibit a pure perovskite structure with the coexistence of rhombohedral ( R ) and tetragonal ( T ) phases, and the T phase content increases with increase in x . A small amount of Bi(Zn 0.5 Ti 0.5 )O 3 ( x ≤ 0.03) that were incorporated into the perovskite lattice of BF-BT can promote the grain growth of ceramics. Secondly, all samples were found with a notable relaxed phase transition behavior, T C of the system decreases with increase in x . The AC impedance spectra of the samples were fitted and analyzed according to the R-CPE equivalent circuit model, the electric impedance of the ceramics at high temperatures was mainly contributed by grain boundaries. Moreover, the dielectric relaxation activation energy of the samples firstly decreases and then increases with increase in x . Finally, the composition with x = 0.02 shows the optimized electrical properties among these samples, including T C = 454 °C, d 33 = 117 pC/N, k p = 23%, tan δ = 0.11, which are mainly benefited from the bismuth content compensation and the substitution of (Zn 0.5 Ti 0.5 ) 3+ for Fe 3+ at B-site reducing the valence change of Fe 3+ in BF-BT.
研究领域:
材料科学
·
物理学
✓ 已验证
DOI
高影响因子
RSC Advances
·
2023
·Vol. 13
·期 15
·10204-10214
·
IF 3.9
Meilin Li,Bei Jiang,Shuoang Cao,Xinyi Song,Yuanqiao Zhang,Lijun Huang,Quanping Yuan
High-performance flexible barium titanate (BaTiO3)-based piezoelectric devices have gained much attention. However, it is still a challenge to prepare flexible polymer/BaTiO3-based composite materials with uniform distribution and high performance due to the high viscosity of polymers. In this study, novel hybrid BaTiO3 particles were synthesized with assistance of TEMPO-oxidized cellulose nanofibrils (CNFs) via a low-temperature hydrothermal method and explored for their application in piezoelectric composites. Specifically, Ba2+ was adsorbed on uniformly dispersed CNFs with a large amount of negative charge on their surface, which nucleated, resulting in the synthesis of evenly dispersed CNF-BaTiO3. The obtained CNF-BaTiO3 possessed a uniform particle size, few impurities, high crystallinity and dispersity, high compatibility with the polymer substrate and surface activity due to the existence of CNFs. Subsequently, both polyvinylidene fluoride (PVDF) and TEMPO-oxidized CNFs were employed as piezoelectric substrates for the fabrication of a CNF/PVDF/CNF-BaTiO3 composite membrane with a compact structure, displaying the tensile strength of 18.61 ± 3.75 MPa and elongation at break of 3.06 ± 1.33%. Finally, a thin piezoelectric generator (PEG) was assembled, which output a considerable open-circuit voltage (4.4 V) and short-circuit current (200 nA), and could also power a light-emitting diode and charge a 1 μF capacitor to 3.66 V in 500 s. Its longitudinal piezoelectric constant (d33) was 5.25 ± 1.04 pC N−1 even with a small thickness. It also exhibited high sensitivity to human movement, outputting a voltage of about 9 V and current of 739 nA for only a footstep. Thus, it exhibited good sensing property and energy harvesting property, presenting practical application prospects. This work provides a new idea for the preparation of hybrid BaTiO3 and cellulose-based piezoelectric composite materials.
研究领域:
材料科学
·
能源工程
·
纳米技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CERAMICS INTERNATIONAL
·
2023
·
IF 5.2
Xiaocui Rao,Xueting Fu,Hai Jiang,Weiping Li,Laihui Luo
In this work, the cold sintering assisted process was utilized to fabricate dense 0–3 type (1- x )BaTiO 3 - x CaTiO 3 :Pr 3+ ((1- x )BT- x CT:Pr 3+ , x = 0.1, 0.2 and 0.3) binary composite ceramics. Under the combined action of uniaxial pressure and temperature, CT:Pr 3+ has been successfully integrated with BT to form the preliminary BT-CT:Pr 3+ composites during cold sintering. It is found that the cold sintering could increase the grain size a little, and annealing at 900 °C significantly promotes the grain size. The prepared (1- x )BT- x CT:Pr 3+ composite ceramics have a pure phase of CT:Pr 3+ , which is difficult to prepare using high temperature solid reaction method when x < 0.23. It is found that all the composite ceramics exhibit excellent ferroelectric properties . Furthermore, a strong photoluminescence , photo-stimulated luminescence and thermal luminescence properties have been obtained. Present study illustrates a potential approach to combine luminescent and piezoelectric properties into the ferroelectric-based composite ceramics by the cold sintering assisted sintering.
研究领域:
材料科学
·
光学
·
电子工程
✓ 已验证
产品关联
DOI
高影响因子
ACTA MATERIALIA
·
2019
·
IF 7.293
Ruixuan Song,Yu Zhao,Weili Li,Yang Yu,Jie Sheng,Ze Li,Yulei Zhang,Hetian Xia,Wei-Dong Fei
Low temperature stability has limited the applications at elevated temperature for ABO 3 -type lead-free ceramics. And multi-grade resonances of piezoelectric ceramics are hardly obtained although the resonances are very important in some applications such as filter and resonator . High piezoelectric properties and large mechanical quality factors with multi-grade resonances can be obtained in (Li + -La 3+ ) co-doped BaTiO 3 ceramics, and excellent temperature stabilities are achieved in the ceramics. It has been shown that the thermal treatments both with and without electric field at 200 °C improve the piezoelectric properties and thermal stability further. Large piezoelectric constant (272 pC N 1 ) and huge mechanical quality factor (2010) was obtained after thermal-electrical treatment, which is caused by Li + -La 3+ ionic pair aligning along the external electric filed during thermal-electrical treatment. Moreover, the present study provides an effective method to design combination properties with high temperature stability for ABO 3 perovskite ferroelectric ceramics .
研究领域:
材料科学
·
物理学
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2020
·
IF 16.683
Enzhu Lin,Zihan Kang,Jiang Wu,Rui Huang,Ni Qin,Dinghua Bao
The selective deposition of noble metals on catalysts is an attractive modification method for improving catalytic efficiency. However, it is sometimes hard to achieve when facet energies of nano-catalysts show negligible differences. Here, we reported a piezoelectrochemical method which can realize the selective deposition of Ag nanoparticles on the positively polar end of {001}-enclosed BaTiO 3 (BTO) nanocubes/cuboids. Furthermore, BTO nanocubes/cuboids with selectively-deposited Ag nanoparticles show approximately 2 times higher piezocatalytic activity than those with randomly-loaded Ag nanoparticles, and much higher than pure BTO nanocubes/cuboids. The piezocatalytic mechanism revealed that the Ag nanoparticles deposited on positively polar end act as “fast lanes” for electrons to transfer to catalysts/solution interfaces, while those loaded on negatively polar end serve as holes trappers hindering ∙OH formation and pollutant degradation. This work confirms an efficient way to improve piezocatalytic performance and provides an insightful discussion of piezocatalytic mechanism.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2019
·
IF 3.45
Zhongyang Wang,Peitao Xie,Guohua Fan,Zidong Zhang,Yao Liu,Qilin Gu,Runhua Fan
Epsilon-negative behavior in metamaterials has attracted increasing attention recently. In this work, excessively percolating BaTiO 3 /Ag composites were synthesized by an in-situ preparation method to achieve negative permittivity. The epsilon-negative behavior is explained by low-frequency plasma oscillation of free electrons, which can be well fitted by the Drude model. Moreover, the negative permittivity of composites can be tuned by adjusting the content of randomly distributed Ag particles. The ac conductivity of excessively percolating BaTiO 3 /Ag composites shows a typical metal-like behavior. Furthermore, the investigation of reactance reveals that the inductive character derived from the conductive network is the main contributor to negative permittivity, as confirmed by the equivalent circuit analysis. This work provides a theoretical recipe for designing negative permittivity, supplements the family of metamaterials, and would further facilitate the practical applications of epsilon-negative materials in electromagnetic devices.
研究领域:
材料科学
·
电磁学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）