DIAMOND AND RELATED MATERIALS
·
2022
·
IF 3.806
Yao Liu,Chunwen Chang,Qiang Xue,Rong Wang,Lingxia Chen,Zeyu Liu,Lin He
Since lead is teratogenic, carcinogenic and mutagenic, people pay increasing attention to lead contamination in water environment. In this work, a novel electrochemical sensor was developed to detect Pb(II) ion in water by PPy , MOFs and bismuth film (BF) modify GCE . Scanning electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, electrochemical impedance spectroscopy , contact angleanalyses, cyclic voltammetry and differential pulse anodic stripping voltammetry were used to characterize the BF-PPy/UIO-66-NH 2 /GCE surface, revealing the physical and electrochemical properties of the electrode. MOFs increased the specific surface area and adsorption site of the electrode. The PPy enhanced the conductivity of the composites materials. MOFs and PPy synergistically promoted the electrochemical performance of the electrode. The deposition potential, deposition time , solution pH and Bi (III) concentration were optimized to determine the optimal detection condition. The electrode has a wide linear range (0.5 to 10 μg/L) with a low detection limit (0.05 μg/L). This electrode also has good anti-interference, repeatability and stability. Besides, it has been successfully applied to the detection of actual water samples. The recovery rates ranged from 95.4 % to 102.8 % with a relative standard deviation (RSD) less than 4.40 %. Our results provide an insight on efficient and rapid detection of Pb(II) ions in water environment in the future.
研究领域:
环境科学
·
分析化学
·
电化学
·
水质监测
✓ 已验证
产品关联
DOI
高影响因子
SOLAR ENERGY MATERIALS AND SOLAR CELLS
·
2019
·
IF 6.019
Jianbo Pan,Rongzong Zheng,Yi Wang,Xingke Ye,Zhongquan Wan,Chunyang Jia,Xiaolong Weng,Jianliang Xie,Longjiang Deng
Functions of electrochromism and energy exchange can be achieved by redox reactions , which indicate designing a bi-functional electrochromic energy storage device (EESD) is feasible. In this paper, a NiO/PB composite nanosheet electrode was prepared via loading Prussian blue (iron (Ⅲ) hexacyanoferrate (Ⅱ), PB) nanoparticles on the surface of NiO nanosheets, meanwhile, a high-performance WO 3 negative electrode was also prepared via novel erythritol-assisted hydrothermal method with NH 4 Cl used as capping agent. The designed EESD exhibited properties of large optical modulation (67.6% at 630 nm), high coloration efficiency (109.6 cm 2 C -1 ), fast switching speed (2.8/7.9 s for bleaching/coloration) and long cycle life (ΔT remaining was 84.1% after 4000 cycles). Meanwhile, the EESD also obtained attractive energy storage properties at a potential window from 0 to +1.3 V. Impressively, the EESD exhibited a high areal capacitance of 11.50 mF cm -2 at current density of 0.05 mA cm -2 and the process of charging/discharging can be repeated at least 4000 cycles with a little decay. Therefore, the bi-functional EESD exhibits high promising application prospect.
研究领域:
材料科学
·
电化学
·
能量存储
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2016
·
IF 7.145
Yun Yan Su,Zhaogang Teng,Hui Yao,Shou Ju Wang,Ying Tian,Yun Lei Zhang,Wen Fei Liu,Wei Tian,Li Juan Zheng,Nan Lu,Qian Qian Ni,Xiao Dan Su,Yu Xia Tang,Jing Sun,Ying Liu,Jiang Wu,Gui Fen Yang,Guang Ming Lu,Long Jiang Zhang
In this work, we design mesoporous silica-coated Prussian blue nanocubes with PEGyltation to construct multifunctional PB@mSiO2–PEG nanocubes. The PB@mSiO2–PEG nanocubes have good biocompatibility, excellent photothermal transformation capacity, in vivo magnetic resonance and photoacoustic imaging ability. After loading antitumor drug doxorubicin (DOX) in the PB@mSiO2–PEG nanocubes, the constructured PB@mSiO2–PEG/DOX nanoplatforms show an excellent pH-responsive drug release character within 48 h, namely, an ultralow cumulative drug release amount of 3.1% at pH 7.4 and a high release amount of 46.6% at pH 5.0. Upon near-infrared laser irradiation, the PB@mSiO2–PEG/DOX nanoplatforms show an enhanced synergistic photothermal and chemical therapeutic efficacy for breast cancer than solo photothermal therapy or chemotherapy.
研究领域:
纳米技术
·
生物医学工程
·
癌症研究
·
药物递送系统
·
材料科学
✓ 已验证
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2021
·
IF 7.312
Rui Wang,Qiu-hui Hu,Qiu-yue Wang,Ya-li Xiang,Shuang-hui Huang,Yong-zhen Liu,Shu-yu Li,Quan-liang Chen,Qing-han Zhou
The development of membrane for heavy metal ion removal in water treatment is still impeded by low adsorption efficiency, poor selectivity, and deficient recyclability, which has gained great interests in both laboratorial research and industrial application. Herein, our aim is to fabricate the magnetic ion-imprinted PAN membranes (MII-PMs) based on polyacrylonitrile electro-spun nanofibers with improved adsorption ability, selectivity, and recyclability for efficient and selective removal of Pb(II) from water. The chemical structure and chemo-physical properties of the as prepared MII-PMs were characterized. Remarkably, in competitive adsorption experiment the MII-PMs demonstrated a much higher adsorption capacity towards Pb(II) than other interfering metal ions with the selective order of Pb 2+ >Cu 2+ >Mg 2+ >Co 2+ >Ni 2+ >Cd 2+ >Zn 2+ >Na + >K + . In investigation of the adsorption mechanism towards Pb(II), the equilibrium adsorption data of MII-PMs fitted better with Freundlich isotherm equation, and the kinetic parameters matched well with pseudo-second-order mode. In regeneration and reusability experiment, the MII-PMs could be regenerated with eluting solution and displayed good adsorption capacity towards Pb(II) during 6 adsorption–desorption cycles. Only small amount of Fe ions was leached out after the regeneration experiments. Generally, the as prepared magnetic ion-imprinted membrane with improved adsorption capability, high selectivity, and excellent reusability towards Pb(II) ions can be utilized as a promising and efficiently potential adsorbent in actual water treatment.
研究领域:
环境科学
·
材料科学
·
水处理
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2023
·
IF 8.6
Ruilu Yang,Qi Zhang,Jian Shi,Yaping Zheng,Dechao Wang,Jian Zhang,Siyuan Liu,Zhuting Fu
The first example of a magnetic loading functional porous liquid (PL) by employing hollow silicon dioxide (HS) loaded with Fe 3 O 4 as the porous guest, (3-glycidyloxypropyl) trimethoxysilane (KH560) and polyetheramine M2070 as hindered sterically solvents was demonstrated in this paper. This nanoadsorbent (Fe 3 O 4 @HS-PL) was prepared for the decontamination of aqueous solutions from Cu(II) and Pb(II) heavy metals. The hindered sterically solvents ( i.e. , the flexible oligomer chains) endow the Fe 3 O 4 @HS porous guest with a superior flowing behavior at ambient temperature. Various approaches were applied to confirm the morphology, structure and properties of the resultant Fe 3 O 4 @HS-PL. More significantly, the adsorption behavior of Cu(II) and Pb(II) in aqueous solution by Fe 3 O 4 @HS-PL was studied in detail. As expected, combined with the cavity structure from porous guest and amine groups from flexible organic flow layer, Fe 3 O 4 @HS-PL exhibited excellent adsorption capacities of 322.58 and 357.14 mg·g −1 for Cu(II) and Pb(II), respectively, at 298 K, pH 8 and initial concentration of 20 mg·L -1 . The obtained HS and Fe 3 O 4 in Fe 3 O 4 @HS-PL magnetic nanoadsorbent presented average particles size ascertained to be ca. 200 nm and 30 nm, respectively. Moreover, the Freundlich model and pseudo-first-order model has described the adsorption process and adsorption kinetics . The parameters in thermodynamic experiment signified the spontaneity and endothermic properties of the adsorption. Moreover, magnetic loading endowed the Fe 3 O 4 @HS-PL with a superior regeneration performance. A variety of mechanisms containing coordination interaction, porous guest absorption, electrostatic interaction , steric effect and entropy are simultaneously realized in this novel adsorption system. Therefore, the introduction of PLs adsorbents into heavy metal adsorption systems through the construction of PLs materials by magnetic loading and surface amination is of great significance in the field of heavy metal adsorption, eventually starting a new time of pushing forward the development of novel adsorbents for decontamination of aqueous solutions from heavy metal ions.
研究领域:
环境科学
·
材料科学
·
化学工程
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2017
·Vol. 19
·期 7
·5333-5342
·
IF 4.123
Shu-xian Wang,Rui-tang Guo,Wei-guo Pan,Ming-yuan Li,Peng Sun,Shu-ming Liu,Shuai-wei Liu,Xiao Sun,Jian Liu
It was well recognized that Pb had a poisoning effect on a SCR catalyst. In this study, the deactivation mechanism of Pb on the Ce/TiO2 catalyst was investigated based on the characterization results of TPD and in situ DRIFT studies. It was found that the addition of Pb on the Ce/TiO2 catalyst not only inhibited the adsorption and activation of NH3 species, but also led to the decrease of the activity of adsorbed NH3 species in the SCR reaction. The adsorption of NOx species and the oxidation of NO by O2 over the Ce/TiO2 catalyst were also suppressed by the addition of Pb, while the reactivity of adsorbed NO2 species did not decrease. Moreover, the results revealed that the NH3-SCR reaction over the Ce/TiO2 catalyst followed both the E–R and L–H mechanisms, while the NH3-SCR reaction over Ce/TiO2-Pb was mainly controlled by the L–H mechanism. The contributions of the L–H mechanism to the SCR reactions over Ce/TiO2 and Ce/TiO2-Pb decreased with increasing reaction temperature. The deactivation of Ce/TiO2-Pb was mainly attributed to the suppressed NH3 adsorption and activation, accompanied by the inhibited NO oxidation and the decrease of Brønsted acid sites.
研究领域:
环境催化
·
大气污染控制
·
材料化学
·
表面科学
·
物理化学
✓ 已验证
DOI
高影响因子
SPECTROCHIMICA ACTA PART A-MOLECULAR AND BIOMOLECULAR SPECTROSCOPY
·
2024
·
IF 4.3
Yifan Cui,Qiulan Li,Dezhi Yang,Yaling Yang
Peroxidase (POD)-mimicking nanozymes have got great progress in the sensing field, but most nanozyme assaying systems are built with a single-signal output mode, which is vulnerable to the effect of different factors. Thus, establishment of a dual-signal output mode is necessary for acquiring dependable and durable performance. This work described an Fe doped noradrenaline-based carbon dots and Prussian blue (Fe,NA-CDs/PB) nanocomposite as a POD-like nanozyme and modified gold nanoparticles (AuNPs) for the colorimetric and surface-enhanced Raman scattering (SERS) dual-mode sensor of Pb(II) in traditional Chinese medicine samples. With 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) and 3,3′,5,5′-tetramethylbenzidine (TMB) as the substrates, it was found that the addition of Pb(II) inhibited the POD-like activity of Fe,NA-CDs/PB and AuNPs, so it was used for colorimetric and SERS dual-mode assays. The POD-like activity was shown to be a “ping-pong” catalytic mechanism, whereas the addition of Pb(II) produced noncompetitive inhibition with modulatory effects on Fe,NA-CDs/PB. The linear response range for colorimetric and SERS sensor detection of Pb(II) was 0.01–1.00 mg/L with the detection limit of 5 μg/L and 8 μg/L, respectively. This dual-mode detection system shows excellent selectivity. More importantly, the Pb(II) in traditional Chinese medicine samples have successfully assayed with good recovery from 90.4 to 108.9 %.
研究领域:
分析化学
·
纳米技术
·
环境科学
·
传统中药
✓ 已验证
DOI
高影响因子
Materials
·
2021
·Vol. 14
·期 21
·6716
·
IF 3.623
Shiyu Ma,Yan Lu,Bo Wang,Jinkai Li
White LEDs were encapsulated using Cs4PbBr6quantum dots and Gd2O3:Eu red phosphor as lamp powder. Under the excitation of a GaN chip, the color coordinates of the W-LED were (0.33, 0.34), and the color temperature was 5752 K, which is close to the color coordinate and color temperature range of standard sunlight. The electric current stability was excellent with an increase in the electric current, voltage, and luminescence intensity of the quantum dots and phosphors by more than 10 times. However, the stability of the quantum dots was slightly insufficient over long working periods. The photocatalytic devices were constructed using TiO2, CsPbBr3, and NiO as an electron transport layer, light absorption layer, and catalyst, respectively. The Cs–Pb–Br-based perovskite quantum dot photocatalytic devices were constructed using a two-step spin coating method, one-step spin coating method, and full PLD technology. In order to improve the water stability of the device, a hydrophobic carbon paste and carbon film were selected as the hole transport layer. The TiO2layer and perovskite layer with different thicknesses and film forming qualities were obtained by changing the spin coating speed. The influence of the spin coating speed on the device’s performance was explored through SEM and a J–V curve to find the best spin coating process. The device constructed by the two-step spin coating method had a higher current density but no obvious increase in the current density under light, while the other two methods could obtain a more obvious light response, but the current density was very low.
研究领域:
材料科学
·
光电
·
光催化
✓ 已验证
DOI
高影响因子
InfoMat
·
2024
·
IF 22.7
Huan Li,Yu Gao,Xin Hong,Kanghui Ke,Zilong Ye,Siwei Zhang,Kefei Shi,Zhuo Peng,Hao Yan,Man-Chung Tang,Youwei Yao,Ben Zhong Tang,Guodan Wei,Feiyu Kang
Broadband photodetectors (PDs) capable of multi-wavelength detection have garnered significant interest for applications in environmental monitoring, optical communication, spectral analysis, and imaging sensing. Low-bandgap Pb–Sn hybrid perovskite photodetectors can extend the spectral response from the ultraviolet–visible (UV–vis) range to the near-infrared (NIR) and reduce the toxicity associated with Pb 2+ . The strategic introduction of Sn 2+ into Cs 0.15 FA 0.85 Pb x Sn 1− x I 3 ( x = 1, 0.8, 0.6, 0.5, 0.4, 0.2, and 0) not only preserves the cubic crystal structure with conformal multigrain growth but also broadens the film's absorption spectrum from 800 to 1000 nm NIR region. This indicates a well-controlled tunability of the Pb–Sn binary perovskite system. Specifically, the self-powered photodetector with a device structure of ITO/NiO x /PTAA/Cs 0.15 FA 0.85 Pb 0.5 Sn 0.5 I 3 /PCBM/BCP/Ag has shown remarkable optoelectrical properties. It exhibits a high external quantum efficiency (EQE) of up to 80% across the spectrum from 300 to 1000 nm, a responsivity ( R ) exceeding 0.5 A/W, and high detectivity ( D *) value of 1.04 × 10 12 Jones at 910 nm and 3.38 × 10 11 Jones at 1000 nm after weak attenuation. Intriguingly, the dark current of the Cs 0.15 FA 0.85 Pb 0.5 Sn 0.5 I 3 device is four orders of magnitude lower than that of devices made with pristine Pb or Sn only, strongly correlating with its significantly increased built-in potential and reduced trap density. Consequently, it demonstrates a −3 dB bandwidth of 2.23 × 10 4 Hz, fast rise and decay times of 61 and 30 μs, respectively, and a linear dynamic range (LDR) of 155 dB. Benefiting from its high sensitivity, a 5 × 5 PD array for NIR imaging and non-invasive pulse detection for photoplethysmography applications has been successfully demonstrated, showcasing the prosperous potential of Pb–Sn hybrid perovskite in the NIR range.
研究领域:
材料科学
·
光电子学
·
成像技术
·
传感器与执行器
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2023
·
IF 15.1
Pengfei Gao,Yangpeng Zuo,Yulu Yang,Jinxiu Yu,Wuzhe Fan,Ruqing Bai,Weihu Yang,Kaiyong Cai
To resolve the short-term inflammatory storm after the operation and the long-term osteointegration deficiency of titanium (Ti) implant as an artificial hip joint, in this work, a novel functionalized Ti implant with an “on-demand” treatment strategy was explored. The metallopolyphenol network (Epigallocatechin gallate (EGCG) and Strontium) wrapped Prussian blue nanoparticles were prepared and anchored on the Ti surface. During the acute inflammatory phase, the inflammatory acidic microenvironment will result in the degradation of the metallopolyphenol network and the responsive release of EGCG and strontium (Sr) ions. The released EGCG could reduce oxidative stress damage and promote the transition of macrophages from M1 to M2. In comparison, Sr ions could stimulate osteoblast differentiation and achieve the rapid osteogenesis and fixation of implants. To achieve long-term osteointegration efficacy, “on-demand” near-infrared light irradiation for the remained PB particles could be adopted if necessary. The mild photothermal conversion temperature could upregulate the expressions of heat shock proteins around the implant and promote the biosynthesis of type I collagen, as well as the formation of bone matrix. In vitro and in vivo results proved the feasibility of our strategy. It is a prospective method for the modification of Ti implants.
研究领域:
材料科学
·
生物医学工程
·
生物材料
·
组织工程
·
骨科
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2023
·
IF 5.2
Varney Edwin Johnson,Qi Liao,Bob Wisdom Jallawide,Richmond Anaman,Charles Amanze,Peicheng Huang,Wei Cao,Chunlian Ding,Yan Shi
Efficient removal of arsenic (As) and lead (Pb) from industrial wastewater has long been a critical environmental issue due to their serious risk to human health. Therefore, in this work, a modified banana peel biochar (MBPB) was prepared by mixing calcium nitrate , diammonium hydrogen phosphate , sulfuric acid, ferric nitrate with dehydrated banana peel biochar as adsorbent for As(V) and Pb(II) removal in wastewater, and their absorption mechanism was investigated. SEM-EDS, TEM, FTIR , XRD , XPS , BET, kinetic, and isothermal characteristics of MBPB and pristine banana peel biochar (PBPB) were conducted. The behavior of both metal ions on MBPB and PBPB was well explained by the pseudo-second-order kinetic with Langmuir and Freundlich models. We found that the two biochar’s behaviors were mixture processes of monolayer and multilayer adsorption , achieving maximum capacities as determined by the Langmuir model of 39.5 mg g −1 (MBPB-As), 33.2 mg g −1 (MBPB-Pb), 30.8 mg g −1 (PBPB-Pb), and 23.5 mg g −1 (PBPB-As), with maximum efficiencies of 98.7% (MBPB-As) and 90.3% (MBPB-Pb) under optimum conditions. Thermodynamic tests showed that As(V) and Pb(II) removal on MBPB was a spontaneous and endothermic physisorption process. MBPB showed great reusability in As(V) and Pb(II) removal, with removal rates as high as 71.4% and 66.5% after five cycles, respectively. Selective adsorption of As(V) and Pb(II) was also investigated on MBPB, and the removal rate was still high in the mixture of heavy metals. These findings provide a feasible method for the environmental-benign utilization of banana peel as a low-priced adsorbent in wastewater treatment .
研究领域:
环境科学
·
废物管理
·
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
WASTE MANAGEMENT
·
2021
·
IF 7.145
Huayi Chen,Xingjian Yang,Yonglin Liu,Xueming Lin,Jinjin Wang,Zhen Zhang,Na Li,Yongtao Li,Yulong Zhang
Waste chicken feathers are the ideal precursor for the production of low-cost N-enriched biochar. KOH-modified N-enriched biochar (KNB) containing 15.92 wt% N was successfully prepared using waste chicken feathers. The adsorption kinetics results showed that KNB had rapid Cd (2 h) and Pb (1 h) adsorption rates. The Cd and Pb adsorption capacities of KNB (the values of K F were 22.324 (Cd) and 119.654 (Pb) mg 1−(1/n) ·L 1/n ·g −1 ) were 7.07 and 26.52 times higher than those of the original biochar based on the adsorption isotherm results. The KNB was stable at pH 3–6 and had stronger co-adsorption capacities in double-ion systems. Based on the adsorption experiments and various characterization methods, we concluded that the primary Cd and Pb adsorption mechanisms of KNB involved electrostatic interactions, cation-π interactions, complexation, and K + exchange. The precipitation mechanism could partially account for Pb adsorption but not for Cd adsorption. KOH modification enhanced the electronegativity of biochar and then increased the electrostatic attraction. Surface O- and N-containing functional groups were involved in Cd and Pb adsorption. Graphitic-N, oxidised-N, and O C O were the main active adsorption groups, the relative contents of which increased after KOH modification, thus increasing the Cd and Pb adsorption performance. Therefore, KNB can be used as a fast and highly efficient adsorption agent to remove Cd and Pb from wastewater containing either Cd and Pb or a combination of these two metals.
研究领域:
环境科学
·
材料科学
·
废水处理
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）