JOURNAL OF SOLID STATE CHEMISTRY
·
2019
·
IF 2.291
Yuanbo Xie,Fangyuan Zhong,Hongxu Chen,Danni Chen,Jiawen Wang,Junkuo Gao,Juming Yao
In this paper, novel hydrogen-bonded metal-complex frameworks MPM-1-TIFSIX and HOF-21 were selected as adsorbents to adsorb iodine. MPM-1-TIFSIX and HOF-21 were prepared by layering method and mixed stirring method, respectively. The structures of the two HOFs were characterized in detail by XRD , BET, TGA and FT-IR. The adsorption behavior and adsorption capacity of MPM-1-TIFSIX and HOF-21 for iodine were investigated in detail. The experimental data showed that the equilibrium adsorption amounts of MPM-1-TIFSIX and HOF-21 were 205.51 mg/g and 172.86 mg/g, respectively. The adsorption process of MPM-1-TIFSIX was conformed to be pseudo-second-order kinetic, while the adsorption process of HOF-21 was conformed to be pseudo-first-order kinetic. The results indicated that HOFs could be used as iodine capture and storage materials.
研究领域:
材料化学
·
环境化学
·
配位化学
·
多孔材料
·
吸附科学
✓ 已验证
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2019
·
IF 3.131
Shengguo Zhou,Wentao Li,Wenjie Zhao,Chao Liu,Zhiwen Fang,Xiulei Gao
As one of the youngest graphene derivative, fluorinated graphene (FG) with excellent mechanical strength and lubricity was incorporated into polyimide polymer (PI) to strengthen the comprehensive performance of nanocomposite . This article gives a detailed characterization to investigate the tribological behaviors of PI/FG nanocomposite films under different friction conditions including both of dry sliding and seawater lubrication . Firstly, the chloroform-treated FG was proved to be stably dispersed in the PI matrix . Subsequently, mechanical properties, thermal stability and tribological properties of PI/FG nanocomposite films were greatly improved. Finally, analysis of the reasons for the significant improvement in wear resistance from the viewpoint of thermal, mechanical properties and the evolution of friction products. Meanwhile, the transfer of FG from polymer matrix to frictional duality was revealed during tribological testing. The above results suggest the potential application of FG in the field of reinforcing polymer friction properties.
研究领域:
材料科学
·
高分子材料
·
表面工程
·
摩擦学
·
纳米复合材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2018
·
IF 6.945
Dongjiu Xie,Shaojie Chen,Zhihua Zhang,Jie Ren,Lili Yao,Linbin Wu,Xiayin Yao,Xiaoxiong Xu
The combination of high conductivity and good stability against Li is not easy to achieve for solid electrolytes , hindering the development of high energy solid-state batteries . In this study, doped electrolytes of Li 3 P 1- x Sb x S 4-2.5 x O 2.5 x are successfully prepared via the high energy ball milling and subsequent heat treatment . Plenty of techniques like XRD , Raman, SEM, EDS and TEM are utilized to characterize the crystal structures, particle sizes, and morphologies of the glass-ceramic electrolytes. Among them, the Li 3 P 0.98 Sb 0.02 S 3.95 O 0.05 ( x = 0.02) exhibits the highest ionic conductivity (∼1.08 mS cm −1 ) at room temperature with an excellent stability against lithium. In addition, all-solid-state lithium batteries are assembled with LiCoO 2 as cathode, Li 10 GeP 2 S 12 /Li 3 P 0.98 Sb 0.02 S 3.95 O 0.05 as the bi-layer electrolyte, and lithium as anode. The constructed solid-state batteries delivers a high initial discharge capacity of 133 mAh g −1 at 0.1C in the range of 3.0–4.3 V vs. Li/Li + at room temperature, and shows a capacity retention of 78.6% after 50 cycles. Most importantly, the all-solid-state lithium batteries with the Li 10 GeP 2 S 12 /Li 3 P 0.98 Sb 0.02 S 3.95 O 0.05 electrolyte can be workable even at −10 °C. This study provides a promising electrolyte with the improved conductivity and stability against Li for the application of all-solid-state lithium batteries.
研究领域:
材料科学
·
电化学
·
固态电池
·
能源存储
·
无机非金属材料
✓ 已验证
DOI
高影响因子
Small
·
2020
·Vol. 16
·期 38
·2003557
·
IF 11.459
Zheng Liu,Su Zhang,Zhipeng Qiu,Chao Huangfu,Lin Wang,Tong Wei,Zhuangjun Fan
Tin (Sn) is considered to be an ideal candidate for the anode of sodium ion batteries. However, the design of Sn-based electrodes with maintained long-term stability still remains challenging due to their huge volume expansion (≈420%) and easy pulverization during cycling. Herein, a facile and versatile strategy for the synthesis of nitrogen-doped graphene quantum dot (GQD) edge-anchored Sn nanodots as the pillars into reduced graphene oxide blocks (NGQD/Sn-NG) for ultrafast and ultrastable sodium-ion storage is reported. Sn nanodots (2–5 nm) anchored at the edges of “octopus-like” GQDs via covalent Sn O C/Sn N C bonds function as the pillars that ensure fast Na-ion/electron transport across the graphene blocks. Moreover, the chemical and spatial (layered structure) confinements not only suppress Sn aggregation, but also function as physical barriers for buffering volume change upon sodiation/desodiation. Consequently, the NGQD/Sn-NG with high structural stability exhibits excellent rate performance (555 mAh g −1 at 0.1 A g −1 and 198 mAh g −1 at 10 A g −1 ) and ultra-long cycling stability (184 mAh g −1 remaining even after 2000 cycles at 5 A g −1 ). The confinement-induced synthesis together with remarkable electrochemical performances should shed light on the practical application of highly attractive tin-based anodes for next generation rechargeable sodium batteries.
研究领域:
材料科学
·
电化学
·
纳米能源
·
储能材料
·
先进电池技术
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Rui Huang,Hongye Wang,Cheng Tao,Hua Hao,Zhonghua Yao,Hanxing Liu,Minghe Cao
Thin film capacitors with large energy storage density and high breakdown strength are widely used in modern electronic fields. To solve the problems of interface effect and different polarization mechanism between matrix and fillers in conventional heterogeneous structure composite thin film capacitors, a new-type inorganic microcrystal-amorphous composite film of 0.92BaTiO 3 -0.08Bi(Ni 0.5 Zr 0.5 )O 3 (0.92BT-0.08BNZ) are prepared by sol–gel method. The amorphous matrix improving the breakdown strength is introduced into the film by adjusting preparation technology. Moreover, the nano-scale polar microcrystalline regions (fillers) are introduced and uniformly distributed in the amorphous matrix under various annealing temperatures. Through investigating the influence of different amorphous matrix and microcrystal trend on the dielectric and energy storage properties, it is found that synergistic effect between the polarized microcrystalline regions and the amorphous matrix are optimal at an annealed temperature of 550 ℃. The result shows that a high energy storage density of 103.7 J cm −3 and an efficiency of 88.3% are obtained under the electric field of 8.30MV cm −1 . Simultaneously, the excellent dielectric and energy storage stability is achieved in a wide temperature range of 20–200 °C. Conclusively, this microcrystal-amorphous composite film overcome the low energy storage capability and poor thermal stability of conventional composite films and provide a feasible way for preparing high energy storage performance films.
研究领域:
材料科学
·
介电材料
·
储能技术
·
无机非金属材料
·
功能薄膜
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2018
·
IF 6.735
Xijun Wei,Yanhong Li,Huarong Peng,Ming Zhou,Yingqing Ou,Yibin Yang,Yunhuai Zhang,Peng Xiao
In this work, hollow CoS nanobox (noted as HCSN) have been successfully synthesized via annealing and hydrothermal process from zeolitic imidazolate framework (ZIF-67) template. When tested as positive electrode materials in alkaline aqueous electrolyte, it shows high specific capacitance of 720 F g −1 at a current density of 1 A g −1 , good rate capability (82.1%) and good cycling stability with 86.4% capacitance retention over 10,000 cycles at 10 A g −1 . To further demonstrate the advantages of our ZIF-67 derived materials, asymmetric energy storage device was assembled (HCSN//NC), where the as-prepared HCSN was employed as the anode and ZIF-67-derived nanoporous carbon (noted as NC) as the cathode. This device achieves high energy density (80 Wh kg −1 at a specific power density of 882 W kg −1 ), good rate capability (53.3 Wh kg −1 even at a specific power density of 7.9 kW kg −1 ) and long-term stability up to 10,000 cycles. More importantly, it could simultaneously light up 12 LEDs in parallel, demonstrating its potential in practical applications.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
功能材料
·
应用物理
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2024
·
IF 9.4
Wenbin Wu,Ping Zhang,Siqi Chen,Xiaohong Liu,Guilin Feng,Meihua Zuo,Wangyan Xing,Bin Zhang,Weifeng Fan,Heng Zhang,Ping Zhang,Jie Zhang,Wei Xiang
O3 phase layered oxides are highly attractive cathode materials for sodium-ion batteries because of their high capacity and decent initial Coulombic efficiency. However, their rate capability and long cycling life are unsatisfactory due to the narrow Na + transfer channel and irreversible phase transitions of O3 phase during sodiation/desodiation process. Constructing O3/P2 multiphase structures has been proven to be an effective strategy to overcome these challenges. In this study, we synthesized bi-phasic structured O3/P2 Na(Ni 2/9 Fe 1/3 Cu 1/9 Mn 1/3 ) 1- x Mn x O 2 ( x = 0.01, 0.02, 0.03, 0.04, 0.05) materials through Mn doping during sodiation process. Benefiting from surface P2 phase layer with the enhanced Na + transfer dynamics and high structural stability , the Na(Ni 2/9 Fe 1/3 Cu 1/9 Mn 1/3 ) 0.98 Mn 0.02 O 2 (NFCM-M2) cathode delivers a reversible capacity of 139.1 mA h g −1 at 0.1 C, and retains 71.4 % of its original capacity after 300 cycles at 1 C. Our work provides useful guidance for designing multiphase cathodes and offers new insights into the structure-performance correlation for sodium-ion cathode materials.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
固态化学
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2018
·
IF 5.116
Chenxi Zhang,Xueshuang Deng,Jianfeng Zheng,Xin Zhou,Jianhua Shi,Xiaohong Chen,Zhuo Sun,Sumei Huang
We report a simple and low-cost approach to enhance the longstanding stability of the perovskite solar cell (PSC) through the application of low-temperature grown SnO 2 nanorod (NR) arrays. SnO 2 NR arrays were fabricated by an aqueous synthesis method in the presence of hydrochloric acid and using thin compact SnO 2 as seeds. The influence of HCl concentration on the photovoltaic (PV) performance of the SnO 2 NR array based PSC device was investigated. The formed crystalline SnO 2 nanorods with square transversal-sections were oriented on the FTO facets in a well-defined and perpendicular fashion at an optimal HCl concentration. The optimized width and length for SnO 2 nanorods were 30 nm and 150 nm, respectively. Consequently, efficient and stable SnO 2 nanorod based perovskite devices were obtained with an average power conversion efficiency (PCE) of 16.57%. The SnO 2 nanorod array based PSCs demonstrated considerably better ultraviolet (UV) and ambient air stability than the planar SnO 2 and notably mesoporous TiO 2 solar cells. This paper provides a prospective scheme to grow high-quality three-dimensional SnO 2 nanorod arrays for highly stable and efficient PSCs.
研究领域:
材料科学
·
纳米科技
·
能源化学
·
光伏技术
·
半导体器件
✓ 已验证
DOI
高影响因子
SOLID STATE IONICS
·
2018
·
IF 2.751
Yuzhen Duan,Junming Guo,Mingwu Xiang,Jinyu Zhu,Changwei Su,Hongli Bai,Xiaofang Liu,Wei Bai,Rui Wang
A series of single crystalline spinel LiNi x Mn 2- x O 4 (0 ≤ x ≤ 0.10) cathode materials were synthesized in virtue of a facile solution-combustion approach. The morphology and the structure of all as-prepared samples were synthetically investigated with the X-ray diffraction (XRD), the scanning electron microscopy (SEM), the high-resolution transmission electron microscopy (HRTEM), and the X-ray photoelectron spectrometer (XPS). According to these investigation results, Ni-doping content has a significant impact on the control of morphology and crystalline structure, hence the as-prepared LiNi x Mn 2- x O 4 samples exhibit polyhedral morphology with high crystallinity and average size of 100–200 nm. This unique polyhedral crystal structure has numerous surfaces fitting the (111) crystalline orientation which exhibit the smallest Mn dissolution in electrolytes, whilst stabilizing the spinel framework. Owing to the merits of both single crystalline polyhedral structure and appropriate Ni-doping, the as-obtained LiNi x Mn 2- x O 4 cathodes reveal enhanced rate capability coupled with long cycling performance. In especial, the LiNi 0.08 Mn 1.92 O 4 presents a initial discharge capacity of 101.3 mAh/g and ultralong cycle stability up to 2000 cycles at 1C, whilst showing enhanced cycle performance when temperature increases to 55 °C. Excellent capacity retention of 72% and 63% is also obtained after 1000 cycles even at high current rate of 5C and 10C. This study may contribute to an effective candidate approach for the obvious improvement on lithium ion batteries in term of electrochemical activity.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
纳米材料
·
固态化学
·
电池技术
✓ 已验证
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2024
·
IF 4.9
Hui Jiang,Xiaoyan Liu,Ying Xu,Yongying Jia
As a complex component of crude oil, asphaltenes determine the stability of emulsion . However, the mechanism of asphaltenes stabilize emulsion is still insufficient recognition due to the complexity of the molecular structure of asphaltenes. In this paper, the experiments and dissipative particle dynamics simulations were used to study the interfacial properties of asphaltenes. The adsorption of asphaltenes at the oil–water interface was studied by interfacial tension (IFT) experiments. A realistic molecular structure of asphaltene was constructed on the results of the characterization of the asphaltenes. The effects of asphaltenes concentration, temperature, and shear on the formation and stability of emulsion based on this molecular structure were investigated by simulations. The results show that the IFT decreases as asphaltenes concentration increases, while the droplet size of the emulsion decreases and becomes more uniformly distributed. Increasing the temperature enhances the interfacial activity of the asphaltenes, but also promotes its dissolution in the oil phase, which has a negative effect on reducing the IFT value and the stability of the emulsion. As the shear rate increases , the configuration of the emulsion changes from droplets to ellipsoids and rods, and the structure of the interfacial film is disrupted. This work provides useful insights into the mechanisms of asphaltenes concentration, temperature, and shear on the stability of the emulsion.
研究领域:
石油化学
·
胶体与界面科学
·
流体力学
·
分子模拟
·
能源工程
✓ 已验证
DOI
高影响因子
PARTICLE & PARTICLE SYSTEMS CHARACTERIZATION
·
2023
·Vol. 40
·期 8
·2300032
·
IF 2.7
Hao Jiang,Chenxi Zang,Yixiu Dong,Min Lai,Shuhong Xu,Jingkun Xu
CsPbX 3 (X = Cl, Br, I) nanocrystals (NCs) are competitive materials for a wide range of applications because of their outstanding optoelectronic properties. Ion doping has been demonstrated as one powerful method for improving the optical properties of CsPbX 3 NCs. However, the conventional ion-doping approaches are tedious, and generally performed under an inert atmosphere and high temperature. In this work, a one-step ultrasonic-assisted approach is demonstrated to prepare doped CsPbX 3 NCs. To demonstrate the universality of the ultrasonic-assisted ion-doping approach, three ion-doped perovskite NCs are prepared, which represent three common improvements effects of ion doping on perovskite NCs, namely improved stability, PL emission, and photoluminescence quantum yields (PLQYs) of perovskite NCs. Sr-doped CsPbI 3 NCs showed improved phase stability. Mn-doped CsPbCl 3 NCs showed dual-color emissions at 406 and 580 nm. The PLQYs of the as-prepared Ni-doped CsPbCl 3 NCs are greatly improved, from 10.1% to 71%. Such a simple and versatile ion-doping approach may promote the practical applications of all-inorganic perovskite NCs.
研究领域:
材料科学
·
纳米技术
·
光电子学
·
无机化学
·
半导体材料
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2014
·Vol. 2
·期 34
·13859-13867
·
IF 0
Chengxin Peng,Huixin Chen,Qiongyu Li,Weiwei Cai,Qin Yao,Qingsheng Wu,Jinhu Yang,Yong Yang
The silicon material is the most promising candidate for developing new-generation lithium-ion batteries with high energy and power output. However, there remains a significant challenge due to poor electrical conductivity and pulverization of the silicon based anode during cycles. Aiming to solve these problems, in this work we fabricate a novel 3D composite architecture made of a Si@SiOx core–shell nanowire array grown on a 3D graphitic foam (Si CNW–3D GF) substrate by a well-designed multiple-step approach. The prepared Si CNW–3D GF composite shows the integrated advantages for high-performance lithium ion batteries, including its light weight, open macroporosity, high conductivity, high Si NW loading, excellent flexibility as well as SiOx buffer layers. As a result, the Si CNW–3D GF composite exhibits excellent performance such as high reversible lithium storage capacity (3603 mA h g−1 at a current density of 840 mA g−1), excellent cycling performance (up to 100 cycles) and superior rate capability (2299 mA h g−1 at 4200 mA g−1 and 1206 mA h g−1 at 8400 mA g−1), which is 2 times that of the Si CNW electrode where Si CNWs were grown directly on a stainless steel current collector without the presence of 3D GF.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
功能材料
·
电池技术
✓ 已验证
DOI
危险品化学品经营许可证（带存储）