BIOMACROMOLECULES
·
2019
·
IF 5.667
Yangyang Yan,Chen Gao,Jianjun Li,Tao Zhang,Guang Yang,Zhongkai Wang,Zan Hua
Herein we report the synthesis of a cellulose-grafted bottlebrush copolymer with nucleobases as hydrophobic moieties. Well-defined spherical micelles from this bottlebrush copolymer were fabricated via a solvent switch method. A morphological transition from spheres to worms was only observed to occur when a diblock copolymer with a complementary nucleobase functionality was introduced. Hydrophobic interaction is not capable of triggering the morphological transformation, and the diblock copolymer with the heterogeneous acrylamide nucleobase monomer can induce the morphological transition at higher A:T molar ratios, which might be caused by the weak H-bonding interaction. This supramolecular “grafting to” method enables the preparation of a series of nanoparticles with similar shapes and dimensions but distinct surface properties such as zeta potentials. Moreover, reversible morphological transitions between worm-like micelles and spheres can be achieved using a reversible collapsing and swelling of a thermoresponsive polymer. This work highlights that a supramolecular “grafting to” approach between complementary nucleobases can be utilized to tune morphologies and surface properties of nanoparticles.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Environmental Chemistry Letters
·
2019
·Vol. 18
·期 1
·237-241
·
IF 4.617
Zhao Xiaodan,Wu Ying,Xing Danying,Ren Zhaojin,Ye Lingfeng
Sulfate radicals (SO 4 ·− ) are highly efficient for the degradation organic pollutants. SO 4 ·− can be produced by activation of sulfites, yet actual heterogeneous activators exhibit a lower reactivity for activation of sulfite to SO 4 ·− at pH 7.0–8.0. Here we hypothesized that zero-valent copper can activate sulfite under mild conditions. We tested the reaction with iohexol, diatrizoate, atrazine, benzoic acid, and p -chlorobenzoic acid contaminants. Reactive radicals were identified by electron paramagnetic resonance, fluorescence spectrometry, and radical scavenging experiments. Results show up to 90% abatement of contaminants by combining sulfite with zero-valent copper at pH 8.0. Moreover, zero-valent copper maintains a crystalline stability and satisfactory reusability with iohexol abatement efficiency up to 80% after five runs.
✓ 已验证
产品关联
DOI
高影响因子
CHEMOSPHERE
·
2019
·
IF 5.108
Liheng Liu,Dongwei He,Fei Pan,Rong Huang,Hua Lin,Xuehong Zhang
In this study, Fe/Cu, Fe/Al/Cu, Fe/Cu/C and Fe/Al/Cu/C internal electrolysis systems (IESs) were constructed and used to treat methylene blue dye (MB) wastewater. The effects of filler mass ratio, filler dosage, solution pH, reaction time and reaction temperature on COD removal were discussed, while the kinetics, thermodynamics and mechanism of COD removal were also investigated. The results showed that when the COD removal rates were basically the same, the reaction times of Fe/Al/Cu, Fe/Cu/C and Fe/Al/Cu/C IESs were shorter, and the filler dosages were lower. For the four systems, the appropriate pH was around 5, while the suitable reaction temperature was in the range of 20–25 °C. The COD removals of these four IESs were generally greater than 90%. The COD removal processes of the four systems could be better described by the improved pseudo-second-kinetic model, and the liquid film diffusion was the rate-controlling step. Moreover, the COD removal was a spontaneous and endothermic process. MB was degraded into inorganic substances in four steps. In addition, the FTIR characterization of the fillers before and after reaction suggests the four IESs have good stability.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2018
·Vol. 29
·期 15
·13180-13187
·
IF 2.324
Wang Yan,Wang Yishu,Ma Limin,Han Jing,Guo Fu
Due to the asymmetric structure of Sn unit cell, the electromigration behaviors of Sn based solder joints were significantly depended on the crystal orientation of Sn grain. The present investigation illustrated the effect of Sn grain c -axis on the intermetallic compounds (IMCs) growth under current stressing. The Cu particles reinforced Sn3.5Ag solder joint was selected to obtain various observed surfaces of the sample after 46 days current stressing. The front side, back side, right side and anode side of the sample represented different phenomena, which reflected and proved the importance of c -axis orientation on Cu atomic migration in three-dimension space. Besides, another composite solder joint was polished severe times on the observed surface which was full of IMCs. It showed that the IMCs were covered on the Sn-based solder, and there was crack at the cathode underneath the front surface after 38 days current stressing. The IMC growth behavior would be well understood by systematic study in this work.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2018
·
IF 4.229
Jianxun Zhao,Xiaojie Zhai,Xing Tao,Heng Liu,Wanqiang Liu,Dayong Jiang,Shang Gao
Mechanical alloying technique was used to prepare the Co 0.9 Cu 0.1 Si alloy. Composite materials of Co 0.9 Cu 0.1 Si doping with different amounts of multi-walled carbon nanotubes (MWCNTs) or lithium modified MWCNTs (Li-MWCNTs) were obtained via ball-milling to improve the hydrogen storage performance of Co 0.9 Cu 0.1 Si. XRD , SEM and TEM were used to analysis the structural properties of the samples. A three-electrode battery system was carried out to test the electrochemical properties . After the addition of MWCNTs, the composites showed higher discharge capacity, stronger HRD, better cyclic stability and lower charge-transfer resistance than the original Co 0.9 Cu 0.1 Si alloy. The electro-catalytic function of MWCNTs, the reduction of particle size and the raise of specific surface area for Co 0.9 Cu 0.1 Si alloy may provide larger electrochemically accessible area and rapid channel for hydrogen transportation , which are important to enhance the electrochemical performance of the alloy. Moreover, a further improvement was achieved after the addition of Li-MWCNTs, illustrating that the MWCNTs and lithium species had synergistic effects in improving the discharge capacity and reaction kinetics of the Co 0.9 Cu 0.1 Si alloy electrode. As the weight ratio of the alloy and Li-MWCNTs was 15:1, the optimal discharge capacity of 624.4 mAh/g and the highest capacity retention of 67.5% were achieved.
✓ 已验证
产品关联
DOI
高影响因子
Chinese Physics B
·
2018
·Vol. 27
·期 6
·066108
·
IF 1.321
Qing Yu,Jiangjian Shi,Pengpeng Zhang,Linbao Guo,Xue Min,Yanhong Luo,Huijue Wu,Dongmei Li,Qingbo Meng
A study of the self-healing phenomenon of Cu2ZnSn(S, Se)4 (CZTSSe) solar cells has shown more than 10% enhancement in cell performance after storage at room temperature for a week, with a significant improvement in the open-circuit photovoltage (Voc) and fill factor (FF). In addition, up to 10.45% power conversion efficiency (PCE) has been achieved. No obvious change in crystallinity, crystal phase, optical absorption or elemental distribution in the CZTSSe films was detected on examining the x-ray diffraction (XRD) pattern, Raman spectrum, ultraviolet-visible (UV-Vis), and TOF-SIMS. Further investigations on the charge carrier concentration, charge radiative recombination, and band structure suggest that the enhancement in PCE stems mainly from a reduction in deep defects of the CZTSSe semiconductor film.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS
·
2018
·
IF 3.046
Xiaoshan Yang,Xiufang Cui,Guo Jin,Jinna Liu,Yanbo Chen,Zhe Liu
Laser additive manufacturing (LAM) is a novel method for processing compositionally graded alloys and becomes increasingly important in the context of next-generation manufacturing technology. In this work, (Fe 60 Co 35 Ni 5 ) 78 Si 6 B 12 Cu 1 Mo 3 soft magnetic alloys with different laser power were designed and processed by the LAM. The magnitudes of magnetic properties were analyzed, and the relationships among composition-microstructure-magnetic properties assessed. Results show that the (Fe 60 Co 35 Ni 5 ) 78 Si 6 B 12 Cu 1 Mo 3 alloys by LAM exhibits relative uniform microstructure and comparable magnetic property compared with those conventional processed alloys. The bcc dominated microstructures exhibit a substantially higher saturation magnetization (Ms). With the increase in power, the average grain size of the alloy increased slightly and the increasing volume fraction of the Fe Si phase leaded to the enhancement of magnetization. The (Fe 60 Co 35 Ni 5 ) 78 Si 6 B 12 Cu 1 Mo 3 alloys with laser power of 3000 W exhibits the highest Ms (199 emu/g). The appearance of Fe 3 B results in coarse dendrites and high coercivity (Hc) in the multiple re-heating cycles.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ELECTRONIC MATERIALS
·
2018
·Vol. 48
·期 4
·1840-1845
·
IF 1.566
Sun Fu-Hua,Dong Jinfeng,Tang Huaichao,Zhuang
Hua-Lu,Li Jing-Feng
Cu 12 Sb 4 S 13 tetrahedrite is an abundant natural that is also environmentally friendly. There have been efforts made to reach a unity of ZT value through optimizing the interdependence of electrical and thermal performance. In this study, we reported on ZnO nanoparticles-dispersed Cu 11.5 Ni 0.5 Sb 4 S 13− δ composites that were synthesized by the mechanical alloying and spark plasma sintering method. The structural characterizations were conducted via scanning electron microscopy, electronic probe microscopic analysis and transmission electron microscopy. The ZnO-nanoparticles were uniformly distributed in the Cu 12 Sb 4 S 13 grains. ZnO was used as a heterogeneous nucleation site to reveal the effectiveness of reducing thermal conductivity, likely derived from the strong low/mid-frequency phonon scattering. The lowest lattice thermal conductivity, 0.33 W m −1 K −1 , was obtained at 673 K in 0.5 vol.% of ZnO sample. A small quantity of ZnO addition led to a high ZT ∼ 1.0 at 723 K, which increased by ∼ 42% in the pure-phased Cu 12 Sb 4 S 13− δ sample.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2018
·
IF 3.909
Cihui Tian,Sajid Asghar,Yurui Xu,Zhipeng Chen,Jingwei Zhang,Qineng Ping,Yanyu Xiao
Redox-sensitive micelles based onhydrophilic hyaluronic acid-ss-hydrophobic curcumin conjugate were designed as a novel delivery system for gliomas targeting. Furthermore, the obtained micelles were further functionalized with Tween 80 (CUR-THSC) for better brain penetration. Dynamic light scattering experiment and in vitro release study showed that the synthetic disulfide-linked conjugate possessed redox-sensitivity under high glutathione conditions. Spherical micelles with a mean particle size of 74.2 nm, negative zeta potential (−30.25 mV), high entrapment efficiency (94.12%) and drug loading (8.9%) were obtained. XRD analysis of micelles revealed amorphous form of the encapsulated drug. CUR-THSC micelles showed good plasma stability and did not induce any hemolysis in erythrocytes. In addition, highest cytotoxicity in G422 cells was observed compared to the free curcumin group and non-sensitive micelles group. These results indicate that the Tween 80-modified hyaluronic acid-ss-curcumin micelles could emerge as a promising platform for the delivery of curcumin in the treatment of gliomas.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Nano Materials
·
2018
·
IF 0
Zequn Yang,Hailong Li,Chen Liao,Jiexia Zhao,Shihao Feng,Pu Li,Xi Liu,Jianping Yang,Kaimin Shih
Rattle-type Fe3O4@CuS synthesized using a two-step method was applied for elemental mercury (Hg0) adsorption in coal combustion flue gas for the first time. The Fe3O4 with strong magnetization was an ideal candidate as a core to make the sorbent recyclable, while the stabilized ultrathin CuS shell assured that the Fe3O4@CuS had a higher Brunauer–Emmett–Teller (BET) surface area with more exposed active sites and stronger magnetization. The optimal operating temperature of 75 °C allowed for the injection of the sorbent between the wet desulfurization (WFGD) and wet electrostatic precipitator (WESP), which removed the detrimental influence of nitrogen oxides. Simulated flue gas (SFG) in this section showed a slight inhibitive effect on Hg0 adsorption over the Fe3O4@CuS, mainly due to the presence of water vapor (H2O). The inhibition of H2O was proven to be the result of an active site prevention effect instead of the widely recognized competitive adsorption effect. The adsorption capacity and rate of the Fe3O4@CuS for Hg0 capture reached 80.73 mg g–1 and 13.22 μg (g min)−1, which were the highest values among the magnetic sorbents currently reported for Hg0 removal from coal combustion flue gas. These properties allowed the sorbent to maintain a 100% Hg0 capture efficiency for more than 20 h with only a 50 mg dosage when no regeneration step was applied. Meanwhile, the contacting time between the sorbent and Hg0 was generally less than 5 s in a typical sorbent injection process. Polysulfides dominated the capturing process and primarily contributed to the extremely high adsorption capacity/rate. A multistep reaction mechanism was proposed to explain the Hg0 adsorption over Fe3O4@CuS. At the first stage, polysulfide participated in Hg0 adsorption as the most active component and was consumed rapidly. After that, S–S dimers, sulfides, and even copper-terminated sites functioned as the adsorption centers. The as-formed mercury–copper (Hg–Cu) amalgam was transformed into mercury sulfide (HgS), a process that was dependent on the extent of the saturation of sulfide sites. With these advantages, Fe3O4@CuS is a promising, cost-effective, highly recyclable, and efficient alternative to the traditional activated carbon for capturing Hg0 in coal combustion flue gases.
✓ 已验证
产品关联
DOI
ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY
·
2018
·
IF 3.974
Zhiyue Liao,Huabin Cao,Xueyan Dai,Chenghong Xing,Xiongwei Xu,Gaohui Nie,Caiying Zhang
To investigate the toxic effects of Molybdenum (Mo) and Cadmium (Cd) on trace elements in digestive organs of Shaoxing duck ( Anas platyrhyncha ), 120 Shaoxing ducks were randomly divided into control group and 5 treatment groups which were treated with a commercial diet containing different dosages of Mo and Cd. On the 60th and 120th days, the beak, esophagus, glandular stomach, muscular stomach, small intestine, large intestine and feces were collected to determine contents of Mo, Cd, copper (Cu), iron (Fe), zinc (Zn) and selenium (Se), then correlation analysis was performed. The results showed that Cd content in digestive organs significantly increased in co-treated groups compared to single treated groups and Mo concentration increased in Mo-treated groups compared to control group, whereas Cu, Fe, Zn and Se concentrations in digestive organs decreased in co-treated groups. Furthermore, Cd and Mo were mainly accumulated in the small intestine and esophagus, respectively. There was a strongly positive correlation between Cd and Mo while they had negative correlation with Cu, Fe, Zn and Se, respectively. In feces, Mo and Fe contents in high dose of Mo group and high Mo combined with Cd group were significantly higher than those in control group, and Cu content in all treated groups significantly increased and Cd, Zn and Se concentrations had no difference. The results indicated that dietary Mo or/and Cd might disturb homeostasis of trace elements in digestive organs of Shaoxing duck. Moreover, the two elements presented a synergistic relationship.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ENVIRONMENTAL TOXICOLOGY AND PHARMACOLOGY
·
2018
·
IF 2.776
Min Xu,Huaqiao Tang,XueRong Zhou,Helin Chen,Qi Dong,Yuanli Zhang,Gang Ye,Fei Shi,Cheng Lv,Bo Jing,Changliang He,Ling Zhao,Yinglun Li
Copper nanoparticles (Cu NPs) have widespread application because of their special physicochemical characteristics, however we need to more clearly study the toxicity mechanism of Cu NPs to ensure its safe use in pharmaceutical and animal feed. Thus, the aim of this study was to evaluate the effects and mechanisms of sub-chronic exposure to Cu NPs on renal CYP450 s of rats. In this study, we investigated the effects of Cu NPs on renal oxidative stress, cytokines and histopathology of rats. We found that Cu NPs (200 mg/kg) significantly disordered the function and structure of the kidney and caused a dose-dependent increase in oxidative stress and cytokines, which significantly decreased the levels of mRNA, protein, and activity of CYP450 s. Micro-coppers (Cu MPs) and Cu ions have similar effects, but their effects on CYP450 s were weaker than Cu NPs. The expression of nuclear receptors were inhibited and the expression of Akt, STAT3/5, CREB, p70S6K, NF-κB, P38 and ERK1/2 were activated when the inhibition effects of CYP450 s activity were observed in renal of rats. Therefore, we believe that Cu NPs can activate the STAT, NF-κB and MAPK signaling pathways to down-regulate the expression and activity of CYP450 s by inducing oxidative stress and inflammatory response in rat kidney.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）