CATALYSIS LETTERS
·
2022
·Vol. 152
·期 11
·3427-3436
·
IF 2.936
Xu Siquan,Xing Xinyi,Wu Han,Shi Xian,Zhang Zongqi,Gao Hui
5-Hydroxymethylfurfural (HMF) is a biomass-derived platform compound with great application potential. Herein, the efficient NbW-SBA-15 series catalysts were prepared by incorporating the niobium and tungsten into the pore wall of SBA-15 mesoporous silica. The physico-chemical features of NbW-SBA-15 catalysts with different proportions of niobium and tungsten were analyzed through ICP-AES, Low/Wide-angle XRD, N 2 adsorption–desorption, SEM, TEM, UV–Vis DRS, Raman spectroscopy, NH 3 -TPD, and Py-FTIR technologies. It was discovered that by changing the incorporating ratio of niobium and tungsten in the pore wall, the acidic nature (acid strength, acid density, and acid ratio) of the catalyst was adjusted, which in turn affected the catalytic performance. As the introduction molar ratio of niobium to tungsten is 1:1, the corresponding [1:1]NbW-SBA-15 catalyst occupied the highest acid density and stronger acid sites, showing the best catalytic activity. A desired HMF yield of 64% was obtained under optimal reaction conditions. Furthermore, after five consecutive testing cycles, the performance of [1:1]NbW-SBA-15 catalyst was maintained, confirming its outstanding hydrothermal stability. Graphical Abstract
研究领域:
催化化学
·
生物质转化
✓ 已验证
DOI
高影响因子
ChemCatChem
·
2017
·Vol. 9
·期 7
·1337-1342
·
IF 4.803
Kaixuan Yang,Xiao Chen,Lei Wang,Liangliang Zhang,Shaohua Jin,Changhai Liang
Graphical Vapor trail : Metal silicide (Pd 2 Si, Ni 2 Si, CoSi, Fe x Si, and Cu 6.69 Si) catalysts supported by SBA-15 are prepared by chemical vapor deposition. Of the SBA-15-supported metal silicide catalysts, Ni 2 Si/SBA-15 presents a modest activity, notable selectivity to styrene (>90 %), and high stability in the selective hydrogenation of phenylacetylene. Metal silicide (Pd 2 Si, Ni 2 Si, CoSi, Fe x Si, and Cu 6.69 Si) catalysts supported by SBA-15 have been prepared by a chemical vapor deposition method under a H 2 atmosphere using (CH 3 ) 2 SiCl 2 as the Si source. Of the SBA-15-supported metal silicide catalysts, Ni 2 Si/SBA-15 presented a modest activity, notable selectivity to styrene (>90 %), and high stability with respect to the selective hydrogenation of phenylacetylene, which is attributed to the active-site isolation and electron transfer in the silicide. Furthermore, Ni 2 Si/SBA-15 also has a high selectivity to diphenylacetylene and 1,4-butynediol, which demonstrates that Ni 2 Si/SBA-15 is a promising, low-cost catalyst alternative to noble-metal catalysts as a selective hydrogenation catalyst.
研究领域:
催化化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2014
·Vol. 4
·期 71
·37470-37478
·
IF 3.708
Jianxiong Xu,Weiwei Liu,Yunfei Yu,Jingjing Du,Na Li,Lijian Xu
A simple synthesis of mesoporous silica nanoparticles with cubic Pmn pore structure (SBA-1) and controlled pore size is reported. The synthesis of mesoporous silica nanoparticles is achieved by employing organic mesomorphous complexes of polyelectrolyte (poly(acrylic acid)) and cationic surfactant (hexadecyl pyridinium chloride) as template, and tetrapropoxysilane as silica source. It is found that the pore size of the synthesized mesoporous silica nanoparticles can be tuned by the incorporation of 1,3,5-trimethylbenzene. By adjusting the amount of 1,3,5-trimethylbenzene in the synthesis, a series of silica nanoparticles with controlled pore size ranging from 2.5 nm to 5.3 nm is obtained. The adsorption properties of the mesoporous silica nanoparticles with different pore size against lysozyme are compared. The results show that mesoporous silica nanoparticles with proper pore size and well ordered pore structure benefit the adsorption and exhibit a low leaching rate.
研究领域:
材料科学
·
生物医学工程
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2013
·
IF 3.535
Huimin Li,Qi Zheng,Jun Luo,Zhixuan Cheng,Jiaqiang Xu
This paper employed a measurement of quartz crystal microbalance (QCM) to investigate the effects of mesopore structures and amount of organic loadings of fluoroalcohol derivatives/SBA-15 (a kind of ordered mesoporous silica sieve) hybrids on the sensing behavior of nerve agent simulant DMMP (dimethyl methylphosphonate). The meso-structure and functional groups of silica-based mesoporous hybrids were examined by SAXS, TEM , N 2 adsorption–desorption isotherms and elemental analysis . The results show that much higher response value and sensitivity are achieved when the hybrid materials have relative higher pore volume and surface area. However, this effect only appears when the mesoporous hybrids have well-ordered porous structure , indicating that ordered meso-structure is critical in fabricating high-performance DMMP sensors. The reason is likely that the ordered meso-structure not only provides a larger number of contactable HFIP groups, but also facilitates molecules diffusion in porous structure. On the other hand, the specific interaction between HFIP/SBA-15 hybrids and DMMP vapor is greatly enhanced as the amount of fluoroalcohol derivatives increases. Therefore, the amount of organic functional groups incorporated plays an important role in determining the selectivity of sensors.
研究领域:
材料科学
·
化学传感器
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF NUCLEAR MATERIALS
·
2019
·
IF 2.547
Hui Dan,Qiang Xian,Li Chen,Tianheng Xiong,Zhengdi Jiang,Facheng Yi,Yi Ding
Mesoporous ammonium molybdophosphate/SBA-15 (AMP/SBA-15) was considered as an excellent adsorbent to remove Cs + from radioactive wastewater. However, AMP/SBA-15 obtained from two-step method suffers from poor stability and low reuse ability. Herein, we reported a facile one-step method to fabricate AMP/SBA-15 using Phosphomolybdic acid (PMA) as acid media. The effect of PMA content on the properties of the resultant AMP/SBA-15 was investigated in detail. And the Cs + adsorption performance of the developed AMP/SBA-15 adsorbents was also evaluated. It was found that the PMA content had a strong influence on the structure and morphology of AMP/SBA-15. The mesoporous structure order of the AMP/SBA-15 decreased with increasing PMA content. The AMP particles were mainly incorporated into the framework of SBA-15. Furthermore, the AMP incorporation rate obtained from one-step method is much higher than that of two-step method. The developed AMP/SBA-15 with AMP in the framework of SBA-15 exhibited good stability and high reuse ability for the removal of Cs + .
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY
·
2020
·
IF 4.192
Jianghua Zhang,Ke Cheng,Hongyan Li,Fawen Yin,Qiaoe Wang,Li Cui,Shasha Yang,Jinggang Nie,Dayong Zhou,Beiwei Zhu
Catalytic production of structured phospholipids (SPLs) containing short-chain fatty acids (SCFAs) in an efficient heterogeneous manner is of great importance from the standpoint of food engineering. Herein, a bifunctionalized sulfonated Zn-SBA-15 catalyst was studied for SPL synthesis through interesterification of soybean lecithin with ethyl propionate or methyl butyrate. Various characterization techniques such as pyridine Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and ultraviolet–visible diffuse reflectance spectroscopy were conducted to determine the physicochemical properties, so as to build the possible structure–reactivity relationship of the catalyst. In screening tests with commercial Amberlyst-15 or other SBA-15-type materials, the as-prepared sample showed promising catalytic performance probably owing to its mesoporous structure and cooperative role of Brönsted and Lewis acid sites. Notably, the sample was easily separated and recycled without obvious deactivation. In general, the investigated catalyst was regarded as one of the promising alternatives to otherwise expensive biocatalysts for SCFA-containing SPL production.
研究领域:
食品工程
·
催化化学
·
生物化学
✓ 已验证
DOI
高影响因子
Carbon Capture Science & Technology
·
2022
·
IF 0
Xinrui Wang,Shanshan Xu,Weiting Yang,Xiaolei Fan,Qinhe Pan,Huanhao Chen
This study presents an investigation of using Co doping strategy to improve the Ni on mesoporous SBA-15 catalyst for promoting catalytic dry reforming of methane (DRM) under non-thermal plasma (NTP) conditions. The work was conducted by following the conventional procedures including pre-/post-reaction characterisation of the relevant catalysts, comparative assessment of various scenarios under the NTP condition and longevity tests. However, we found that the performance enhancement of the NTP system was mainly due to the use of the catalytically inert SBA-15 packing, rather than the variation of metal species on it though the results suggest the possible surface reactions on the metal surfaces. Hence, under the NTP condition, the so-called DRM might be mistaken because (i) the production of H 2 and CO was likely due to the electron-impact dissociation of CO 2 /CH 4 in gas discharge and (ii) surface reactions on a DRM catalyst are rather insignificant. We then carefully analysed and reflected on the findings and proposed further research questions to be shared with the colleagues in the field of NTP catalysis.
研究领域:
化学工程
·
催化科学
✓ 已验证
DOI
RSC Advances
·
2020
·Vol. 10
·期 5
·2472-2482
·
IF 3.119
Jie Meng,Fan Fang,Nengjie Feng,Hui Wan,Guofeng Guan
To improve the catalytic activity when utilizing metal oxides for the combustion of VOCs, Mn/Al-SBA-15 catalysts have been successfully synthesized through an emerging wetness impregnation technique involving Mn(NO3)2 on Al-SBA-15, which has been directly prepared from attapulgite by a hydrothermal method. Compared to Mn/SBA-15, which is prepared with TEOS as its silicon source, all the as-prepared Mn/Al-SBA-15 catalysts demonstrated enhanced catalytic performance in the oxidation of toluene. From this research, the 8% Mn/Al-SBA-15 catalyst presented the best catalytic performance, due to the high efficiency resulting from the high chemical valence of Mn4+. When the concentration of toluene was 2000 ppm, and the space velocity was 60 000 mL (g h)−1, 8% Mn/Al-SBA-15 could effectively reduce the T50 and T90 values of toluene to 201 and 278 °C, respectively; while the 8% Mn/SBA-15 catalyst could reduce the T50 and T90 values of toluene to 223 and 298 °C, respectively. A systematic investigation has been conducted to reveal the synergistic effects of Al doping and manganese loading on the enhanced catalytic performance. The experiments showed impressive results, demonstrating that Al doping can not only increase the surface acidity of SBA-15, but it can also be beneficial for achieving a uniform dispersion of MnOx on the surface and in the pores of Al-SBA-15, resulting in the enhancement of the catalytic performance.
研究领域:
环境科学
·
催化
·
化学工程
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS
·
2024
·
IF 5.8
Liqiang Zhang,Ningmin Zhu,Chaochao Wang,Rongzheng Cui,Riyi Lin
Two-step catalytic pyrolysis of Nannochloropsis sp (NS) was conducted with SBA-15 and ZSM-5. Thermogravimetric analyzer (TG) and pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) were used to investigate the effects of SBA-15 and ZSM-5 on the two-step pyrolysis of NS. The comparative study showed that ZSM-5 and SBA-15 had different effects on the pyrolysis characteristic of NS because of their different property. ZSM-5 had no effects on the kinetic mechanism, but SBA-15 obviously changed DTG curves and the reaction order of the low temperature pyrolysis stage. SBA-15 increased the contents of amines and alkanes to 19.40% and 5.62% in the first step compared with those of the one-step pyrolysis (1.95% and 1.83%). Due to the stronger acid sites, ZSM-5 improved the content of olefins (33.79%) and esters (10.79%) in the first step and the contents of nitriles (11.75%) and aromatic hydrocarbons (31.01%) in the second step compared with those of one-step pyrolysis (10.61%, 5.41%, 0.00%, 8.42%). Acid catalyst had no positive effects on the generation of N-heterocyclic compounds. This study is expected to provide a reference for the efficient pyrolysis utilization of microalgae.
研究领域:
生物能源
·
催化化学
·
环境科学
✓ 已验证
DOI
高影响因子
FOOD CHEMISTRY
·
2018
·
IF 4.946
Nanjing Zhong,Weilin Chen,Liyan Liu,Hongxiao Chen
In this study, mesoporous silica SBA-15 was modified by organic functional groups through silanization. Series of organosilane compounds were grafted onto the SBA-15, and the obtained functionalized carriers were then used to immobilize the lipase from Rhizomucor miehei (RML). The enzymatic properties of the obtained immobilized RML samples were evaluated, and the catalytic efficiencies in glycerolysis of triacylglycerols (TAG) reaction were studied. Compared with the parent SBA-15 immobilized RML, the organic modification gave a maximum improvement of enzymatic activity from 200.00 to 13211.11 U/g; in addition, TAG conversion and diacylglycerols (DAG) content increased from 21.28 to 84.24% and 15.45 to 59.03% respectively. The organic modification also decreased the sensitivity of immobilized RML in extreme pH values and increased their thermostability.
研究领域:
生物化学
·
酶工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2017
·
IF 3.615
Mingsen Chen,Lanmei Qin,Yuanli Liu,Faai Zhang
Surface-initiated activators regenerated by electron transfer atom transfer radical polymerization (ARGET ATRP) was employed for controlled grafting of poly(glycidyl methacrylate) (PGMA) and poly(glycidyl methacrylate)-b-poly(methyl methacrylate) (PGMA-PMMA) brushes from mesoporous silica SBA-15. Initiator 2-bromoisobutyryl bromide (BiBB) was immobilized onto the inner surface of SBA-15 by reaction with free silanol groups. The polymerizations were conducted in the mixed solvents cyclohexanone /N, N-dimethylformamide. The strategy of utilizing mixed solvents gave rise to a suitable polymerization rate and resulted in a good control of the PGMA growth within the SBA-15 framework and could obtain polymer chains with well-preserved chain end functionality. Molecular weight of grafted polymer, structure, morphology, and composition of the functionalized SBA-15 were characterized by using gel permeation chromatography (GPC), X-ray powder diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), N 2 adsorption/desorption measurements, fourier transform infrared spectroscope (FT-IR), and thermogravimetry analysis (TGA), respectively. The thickness, polymer grafting density and molecular weight of the grafted polymer can be controlled by adjusting the polymerization time. The deactivator cannot efficient diffuse to convert the propagating chains to the dormant species when the pores are nearly completely filled with the polymer, therefore, increasing grafting density resulted in higher molecular weight and polydispersity index (PDI) values for the grafted polymer chains. This work provides a facile route for preparation of well-defined mesoporous silica/polymer hybrids.
研究领域:
材料科学
·
高分子化学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CATALYSIS
·
2020
·
IF 7.888
Jichang Lu,Jian Fang,Zhizhi Xu,Dedong He,Siyou Feng,Yubei Li,Gengping Wan,Sufang He,Hua Wu,Yongming Luo
Supported MoS 2 based materials are widely used as heterogeneous catalysts. In this work, we propose a rapid and facile method (ultrasound-induced impregnation assisted by microwave thermal treatment) to synthesize mesoporous silica (SBA-15)-supported, few-layer, ordered and K-promoted MoS 2 nanosheets with different K/Mo ratios. The prepared catalysts are characterized by various physical and chemical techniques. Their catalytic performance is evaluated by methyl mercaptan (CH 3 SH) synthesis from CO/H 2 /H 2 S. The results show that our catalysts exhibit a much higher CO conversion and selectivity to CH 3 SH than the catalysts prepared using the conventional impregnation and reported in the literature. The good performance arises because of two main factors: MoS 2 nanosheets of only 2–4 layers and K promotion. Experimental characterizations and (density functional theory) calculations show that the former is the typical nano-size effect, and the latter stabilizes C S bonds when activating COS molecules.
研究领域:
催化材料
·
物理化学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）