Small
·
2019
·Vol. 15
·期 48
·1901527
·
IF 10.856
Zhaofeng Zhai,Bing Leng,Nianjun Yang,Bing Yang,Lusheng Liu,Nan Huang,Xin Jiang
Tremendous demands for highly sensitive and selective nonenzymatic electrochemical biosensors have motivated intensive research on advanced electrode materials with high electrocatalytic activity. Herein, the 3D-networked CuO@carbon nanowalls/diamond (C/D) architecture is rationally designed, and it demonstrates wide linear range (0.5 × 10 −6 –4 × 10 −3 m ), high sensitivity (1650 µA cm −2 m m −1 ), and low detection limit (0.5 × 10 −6 m ), together with high selectivity, great long-term stability, and good reproducibility in glucose determination. The outstanding performance of the CuO@C/D electrode can be ascribed to the synergistic effect coming from high-electrocatalytic-activity CuO nanoparticles and 3D-networked conductive C/D film. The C/D film is composed of carbon nanowalls and diamond nanoplatelets; and owing to the large surface area, accessible open surfaces, and high electrical conduction, it works as an excellent transducer, greatly accelerating the mass- and charge-transport kinetics of electrocatalytic reaction on the CuO biorecognition element. Besides, the vertical aligned diamond nanoplatelet scaffolds could improve structural and mechanical stability of the designed electrode in long-term performance. The excellent CuO@C/D electrode promises potential application in practical glucose detection, and the strategy proposed here can also be extended to construct other biorecognition elements on the 3D-networked conductive C/D transducer for various high-performance nonenzymatic electrochemical biosensors.
研究领域:
生物医学工程
·
纳米医学
·
电化学传感
·
生物传感器
·
材料科学
·
分子诊断
·
转化医学
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Ruihan Wang,Nanxi Dong,Guofeng Tian,Gang Liu,Bo Zhou,Shengli Qi,Dezhen Wu
In order to allow polyimide (PI) to resist the erosion of atomic oxygen (AO) in Low Earth Orbit to extend the life of the aircraft, an in-situ precursor network approach was proposed to manufacture the inorganic gradient microstructure across the organic/inorganic transition interface and simplify the process, which create a three-tier microstructure film and lead the dense SiO 2 protective layer firmly grasps the PI film. Benefiting from the integrated structure, SiO 2 -coated PI film shows remarkable surface and interface state after 3000 times mechanical bending, which able to delay the initial AO corrosion caused by the defect of the protective layer, resistance to AO reported as AO erosion yield of 2.39 × 10 −26 cm 3 O atom −1 under 7 × 10 21 O atoms cm −2 AO fluence. This work proposes a novel approach for the fabrication of high-performance and AO resistant PI to enable the aircraft to complete more efficient and highly integrated flight missions and shows great potential in the general preparation of organic-inorganic interface.
研究领域:
高分子材料科学
·
航天材料工程
·
表面与界面化学
·
空间环境效应
·
功能涂层技术
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2018
·Vol. 2
·期 10
·2154-2159
·
IF 0
Xing Guo,Bingjuan Zhang,Zhenhua Lin,Jie Su,Zhou Yang,Chunfu Zhang,Jingjing Chang,Shengzhong (Frank) Liu,Yue Hao
The electron/hole transport layer plays a very important role in the planar structure of perovskite solar cells. Conjugated polymers have received considerable attention for use in perovskite solar cells as hole/electron transport layers and passivation layers. Although the devices based on conjugated polymer hole transport layers have achieved much progress, their performance is still inferior to that of devices based on the conventional spiro-OMeTAD hole transport layer. Here, we investigated the solvent vapor annealing (SVA) effect on conjugated polymers as well as the corresponding perovskite solar cell devices. It was found that SVA treatment could enhance the hole charge carrier mobility and thin film crystallinity. Meanwhile, the charge transfer efficiency was enhanced, and charge recombination was reduced. Hence, the conjugated polymer based device exhibited comparable or even better performance compared with the conventional spiro-OMeTAD based device. Moreover, the device stability was also improved.
研究领域:
材料科学
·
光伏技术
·
纳米科技
·
表面与界面化学
·
凝聚态物理
·
能源材料
·
器件物理
✓ 已验证
DOI
MACROMOLECULAR CHEMISTRY AND PHYSICS
·
2019
·Vol. 220
·期 18
·1900299
·
IF 2.622
Huidong Yang,Hong Wang,Jingang Feng,Yumin Ye,Wenna Liu
Asymmetric divinyl monomers are attractive candidates for constructing functional polymer thin films owing to their ability to undergo further reactions after polymerization. Here, the first solventless synthesis of poly(allyl methacrylate) (PAMA) film with retention of abundant allyl groups using initiated chemical vapor deposition (iCVD) is reported. It is demonstrated that lower substrate and filament temperatures lead to better allyl retention, while higher temperatures lead to intramolecular cyclization. The retained allyl groups can be further crosslinked under UV light, and the crosslinking degree can be easily tuned by adjusting the exposure time. Patterning of iCVD PAMA films with 20 µm resolution using a TEM grid as photomask is also demonstrated. The reported synthesis method suggests possible solventless incorporation of AMA in thin films as a latent crosslinker or anchoring sites for further functionalization. The solventless patterning can also extend patterning technique to solvent-sensitive and non-planar substrates.
研究领域:
高分子材料科学
·
表面化学
·
功能薄膜
·
光响应材料
·
生物医学工程
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 139
·期 1
·51418
·
IF 3.125
Lan Hao,Xulin Cui,Xiaoli Wu,Jingtao Wang,Yifan Li,Wenpeng Li,Xingzhong Cao,Haoqin Zhang
Efficient separation of aromatic-aliphatic hydrocarbon mixtures has long been an important topic in chemical industries. Organic nanofiltration (OSN) has been revealing great promise in separating solvent mixtures that has not been effectively resolved by the state-of-the-art technologies. Herein, novel OSN membranes are designed for the separation of toluene and n -heptane. Polyamide active layer with diaminonaphthalene as the aqueous phase monomer is prepared by interfacial polymerization for the first time. The addition of polydimethylsiloxane gutter layer, as well as the combination of spin coating technique and macroporous substrate, renders the membranes with loose and defect-free architectures. The as-designed membranes achieve a rather high selectivity of toluene over n -heptane (>4) together with ultra-high toluene permeance (>180 L m −2 h −1 bar −1 ). These membranes also present excellent stability in the long-term operation.
研究领域:
材料科学
·
膜分离技术
·
化学工程
·
纳米技术
·
高分子化学
·
工业催化
·
绿色化学
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2016
·
IF 5.557
Jiayou Liao,Zhi Wang,Ming Wang,Chengyun Gao,Song Zhao,Jixiao Wang,Shichang Wang
An ion-exchange material – Poly(diallyldimethylammonium carbonate) (PDDACA) containing mobile carbonate has been prepared and it has been blended in a fixed carrier membrane material – polyvinylamine (PVAm) containing abundant amine-group to adjust the carrier microenvironment of the fixed carrier membrane. It makes the mobile carrier cruise around the fixed carrier. On one hand, the CO 2 can be transported continuously in the swing area of fixed carrier through the mobile carriers, the passivity of fixed carrier can be overcome and the utilization efficiency of fixed carrier can be enhanced. On the other hand, a loose and low crystalline system will be obtained by blending two polymers, the number of effective mobile carrier will be increased with mobile carriers unlocking from the crystalline area, and the loose and low crystalline system will provide a good environment for the movement of mobile carriers. These are conducive to enhance the performance of blend membrane in comparision with single polymer membrane. The CO 2 permeance and CO 2 /N 2 selectivity of PVAm-PDDACA membrane, which concurrently contains fixed amine carriers and movable carbonate carriers, can reach 909 GPU and 102 at 0.11 MPa, respectively. The performance of PVAm-PDDACA membrane is enhanced obviously in comparision with PVAm membrane and PDDACA membrane.
研究领域:
膜科学与技术
·
气体分离
·
高分子材料
·
化学工程
·
环境化工
·
能源材料
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2018
·
IF 6.578
Junbin Liao,Jiajie Zhu,Shanshan Yang,Nengxiu Pan,Xinyan Yu,Chao Wang,Jun Li,Jiangnan Shen
Developing highly ion conductive and desirable electrodialysis (ED) performance anion exchange membranes (AEMs) is of great significance. In this work, we report a strategy for fabricating novel AEMs based on a series of fluoro-methyl poly(arylene ether ketone)s having long-side-chain imidazolium groups for ED. Having hydrophilic conductive flexible side-chain imidazolium groups and rigid hydrophobic backbone within AEM matrix, the optimized AEM (PAEK-60-im) shows low water uptake of 24.9% at 80 °C and desirable ion conductivity of 22.01 mS cm –1 at 30 °C. In NaCl removal application of ED, PAEK-60-im shows the NaCl removal ratio of 69.66% within 120 min, outperforming commercial AEM-Type II (68.98%). Accordingly, it has a higher current efficiency of 83.7% but lower energy consumption of 5.9 kWh kg –1 , compared with the commercial one (82.0%; 6.6 kWh kg –1 ). In particular, in selectrodialysis application, possibly owing to the synergistic effect of pore-size sieving effect resulting from macro-separation morphology and hydration energy difference of SO 4 2– ions (–1000 kJ mol –1 ) and Cl – ions (–317 kJ mol –1 ) in feeding solution, PAEK-60-im shows significantly superior monovalent anion perm-selectivity (Cl − /SO 4 2− ) of 7.70 at 30 min, relative to commercial anion-selective Neosepta ACS (5.27) and many other reported mono-valent anion selective AEMs having elegant surface modified layers. The superior ED performance of the homogeneous PAEK-60-im is suggestive of its potential separation application.
研究领域:
材料科学
·
化学工程
·
电化学
·
膜技术
✓ 已验证
产品关联
DOI
高影响因子
AAPS PHARMSCITECH
·
2019
·Vol. 20
·期 1
·1-14
·
IF 2.608
Wang Xingqi,Zhang Yong,Huang Jie,Tian Chunling,Xia Mengqiu,Liu Liu,Li Zhengguang,Cao Jiaojiao,Gui Shuangying,Chu Xiaoqin
The purpose of this paper was to investigate the potential of liquid crystalline (LC) gels for ophthalmic delivery, so as to enhance the bioavailability of pilocarpine nitrate (PN). The gels were prepared by a vortex method using phytantriol and water (in the ratio of 73:27 w / w ). Their inner structures were confirmed by crossed polarized light microscopy, small-angle X-ray scattering, attenuated total reflectance-Fourier transform infrared spectrum, and rheology. The in vitro release studies revealed that PN could keep sustained release from the gels over a period of 12 h. The ex vivo apparent permeability coefficient of the gels demonstrated a 3.83-folds ( P < 0.05) increase compared with that of eye drops. The corneal hydration levels of the gel maintained in the normal range of 79.46 ± 2.82%, hinting that the gel could be considered non-damaging and safe to the eyes. Furthermore, in vivo residence time evaluation suggested that a better retention performance of LC gel was observed in rabbit’s eyes compared to eye drops. In vivo ocular irritation study indicated that LC gel was nonirritant and might be suitable for various eye applications. In conclusion, LC gels might represent a potential ophthalmic delivery strategy to overcome the limitations of eye drops.
研究领域:
药剂学
·
药物递送系统
·
眼科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Plasmonics
·
2015
·Vol. 11
·期 3
·909-915
·
IF 2.238
Wang Shuxia,Wang Hui,Liu Ting,Huang Yingzhou,Chen Guo,Wei Hua,Su Xun,Zeng Xiping,Xia Zengzilu,Wen Weijia,Sun Mengtao
In the propagating process along metal surface, surface plasmon polaritons (SPPs) mainly decay into thermal loss or release into photons, while a part of them were converted into electrons with high energy termed as hot electrons, which have great significance in photonics and electronics. In this work, the generation of plasmonic hot electrons was ascertained in the nanoparticle-film system through plasmon-driven surface catalysis (PDSC) reactions. The surface-enhanced Raman scattering (SERS) spectra of p,p'-dimercaptoazobenzene (DMAB) catalyzed by 4-nitrobenzenethiol (4NBT) experimentally demonstrated the essential catalysis electrons were generated in this hybrid plasmon mode. The results pointed out the priority of plasmonic hot electron generation in the dimer-film gap compared to the monomer-film gap which was analyzed by the surface electric and charge distribution. Furthermore, the SERS spectra of 4NBT in the metal nanoparticle-dielectric film system confirmed the necessity of hybrid plasmon mode in the generation of plasmonic hot electrons in the nanoparticle-film system. Because of the simple configuration and convenient fabrication of nanoparticle-film system, the work on this hybrid plasmon mode has a significant role in promoting the application of plasmonic hot electrons.
研究领域:
纳米光子学
·
等离激元学
·
表面科学
·
催化化学
·
分子光学
·
材料物理
·
半导体器件
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）