CATALYSIS TODAY
·
2020
·
IF 5.825
Yulong Gu,Wei Xu,Yinyong Sun
The development of active oxidative desulfurization (ODS) catalysts is of practical importance. Recently, MOF-808(Zr) has been attempted to use as ODS catalyst due to its various advantages. However, generally MOF-808(Zr) prepared by conventional method was less active in the oxidation reactions due to the lack of defect sites in the structure. In this contribution, we report that the catalytic oxidative performance of MOF-808(Zr) can be enhanced by acid treatment due to the formation of defect sites resulting from the partial removal of organic linkers in the structure. During the experiment, the effect of acid concentration, treatment time, the addition amount of oxidant and reaction parameters on the performance of MOF-808(Zr) was studied. The catalytic results show that MOF-808(Zr) treated with 0.4 M HCl for 1h can catalyze the oxidation of dibenzothiophene completely at 60°C in 15 min. The activity (mole number of converted DBT per hour per unit mass) is 70 mmol h −1 g −1 , which is much higher than that (45 mmol h −1 g −1 ) of parent MOF-808(Zr). In addition, the catalyst can be reused several times without obvious loss of catalytic performance.
研究领域:
材料科学
·
催化化学
✓ 已验证
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2025
·
IF 7.2
Yaqing Zhao,Kang Qin,Yaqing Zhou,Wei Liu,Zhixian Gao,Yuan Peng
Organophosphorus pesticides, commonly used in agricultural practices, remain as residues in food and the environment, presenting a significant risk to human health. The removal of these pesticides is essential to protect both human health and the environment. This study presents an in-situ synthesis technique that combines Cu-MOF (ZZU-282) with electrospinning technology to create a novel cross-linked MOF fiber membrane (cross-linked Cu-MOF-PAN FM, with PAN representing Polyacrylonitrile). The coexistence of micro/meso/macropores within the cross-linked Cu-MOF-PAN FM reduces mass transfer resistance and improves its pesticide removal capacity. The half-life for chlorpyrifos removal by the cross-linked Cu-MOF-PAN FM is about 18 s. The Langmuir model estimates the theoretical maximum removal capacity for chlorpyrifos at 208.3 mg g –1 . Additionally, the removal performance of organophosphorus pesticides is tested in simulated water samples, with results showing that over 70 % of six mixed organophosphorus pesticides are removed within 10 min using the proposed FM. The cross-linked Cu-MOF-PAN FM demonstrates superior efficiency in both rapid and sustained removal of organophosphorus pesticides from water, offering promising potential for environmental applications and pollutant removal. Moreover, the cross-linking process enhances the membrane’s resistance to organic solvents. This in-situ growth and cross-linking method offers a promising approach for fabricating MOF fiber membrane composites.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2024
·
IF 8.1
Kaili Shi,Honghao Su,Keke Liu,Yatao Zhang,Junyong Zhu
Zr Ⅳ -based metal–organic frameworks (MOFs)–featuring exceptional water stability, large surface area, and structural tunability–hold promise for efficient antibiotics adsorption from water. However, their inherent positive charge in neutral environments and the harsh conditions required for their synthesis hinder their effective removal of cationic antibiotics. To address this challenge, a green one-pot synthesis approach was proposed to fabricate phosphotungstic acid-functionalized MOF-808 (termed as PTA@MOF-808) at room temperature for elevated antibiotic adsorption. This approach not only leverages the strong electronegativity of PTA to improve electrostatic interactions and π-π stacking but also finely tailors the pore size of MOF-808, resulting in enhanced adsorption capacity of PTA@MOF-808. The influence of PTA loading, solution pH, and absorbent dosage on the performance of PTA@MOF-808 were studied in detail. Adsorption experiments demonstrated that PTA@MOF-808 outperformed unmodified MOF-808 in removing various positively charged antibiotics, with 5 % PTA@MOF-808 exhibiting maximum adsorption capacities of 548.1 mg g −1 and 482.9 mg g −1 , for DOX and TCHC, respectively. The adsorption process followed the Langmuir isothermal model and the pseudo-second-order kinetic equation. Furthermore, the composite PTA@MOF-808 displayed excellent reusability after multiple adsorption–desorption cycles. These findings highlight the potential of PTA@MOF-808 as a promising absorbent for removing specific antibiotics from water, with significant implications for wastewater treatment.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2018
·
IF 3.927
Shumin Wang,Qingping Guo,Shujun Liang,Peng Li,Jujie Luo
A series of mixed matrix membranes (MMMs) were fabricated with Ni-MOF-74 as filler and poly (styrene-b-butadiene-b-styrene) (SBS) polymer as matrix materials for CH 4 /N 2 separation. MMMs were characterized by Fourier transform infrared (FTIR) spectra, X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). Gas separation behavior was investigated by measuring single and mixed gases. For the single gas, the CH 4 permeability of the MMMs incorporated with 15 wt% Ni-MOF-74 (Ni-MOF-74/SBS-15) reached 83.5 Barrer, which was 116% higher than that of SBS (38.6 Barrer), while its ideal selectivity remained the same. CH 4 permeability can further increase to 176.6 Barrer with the increase in temperature to 55 °C. For the CH 4 /N 2 (50/50 vol%) mixed gas, the Ni-MOF-74/SBS-15 sample exhibited increasing CH 4 permeability (74.7 vs 36.7 Barrer), while selectivity remained unchanged relative to that of the pure SBS membrane.
研究领域:
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL RESEARCH
·
2021
·
IF 6.498
Lin Hu,Dong Mao,Liu-han Yang,Ming-sheng Zhu,Zheng-hao Fei,Shi-xin Sun,Dong Fang
Enhancing photocatalytic performance via electronic modulation have attracted much attention for synergetic photocatalytic degradation of antibiotic pollutant. In this study, a new hetero-structured system is raised, which comprises In 2 S 3 coupled to In-MOF and operates as an efficient photocatalyst for RhB degradation. The formation of hetero-structure and occurred electron modulation of In 2 S 3 /In-MOF hybrid was confirmed by relevant characterizations. Surprisingly, the In 2 S 3 /In-MOF hybrid represented enhanced photocatalytic ability over In-MOF. The photocatalysis of Rhodamine B in presence of In 2 S 3 /In-MOF hybrid has achieved 92.2 % degradation.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
PubMed
高影响因子
Journal of Materials Chemistry C
·
2024
·
IF 5.7
Shizhen Song,Tengfei Zheng,Bo Li,Hangcheng Yang,Qin-Xiang Jia,Zhuting Hao,Wen Zhang,Ying Zhang
Solvent vapor-driven soft actuators have been seen as promising devices for human-environment interaction and gained considerable attention in recent years. Considering the limited types of response solvent and the lack of quantification, MOF/polymer intelligent soft actuators may be a potential candidate of the fabrication of the bio solvent-driven actuators. Thus, this paper present a multiple solvent-driven soft actuator based on MIL-88B/PVDF asymmetric film, and also the comparison to the analogs based on other MIL-88(Fe) series flexible MOFs (including MIL-88A, 88C and 88D) was made for the deformation-structure relationship and the solvent-driven mechanism investigation. The deformation behavior to various organic solvent (including methanol, toluene and chloroform) of the MIL-88(Fe)/PVDF composite films have been investigated, and the structure and composition of the MIL88(Fe) fillers and the composite films were also characterized by SEM, FT-IR, and XRD. Based on the above results, the MIL-88B/PVDF composite which shows the diversity of response objects and the fast deformation response to most of the organic solvents through the solvent swelling/adsorption of the MOF skeleton, was used to fabricate a monolayer soft film composed by MIL-88B, carbon black (CB) and PVDF, namely MIL-88B/CB/PVDF. The MIL-88B/CB/PVDF film not only realizes the excellent deformation-discolor dual-responsive to methanol atmosphere with the visible deformation which could being quickly achieved within 1s under 10 vol % methanol atmosphere and the maximum crimp angle being up to 558o within about 50 s, and also a wide color change range including six view angle-dependent high saturation color (red, orange, yellow, green, blue and purple), but also shows an approximate linear relationship to three of the organic solvents (methanol, toluene and chloroform) between the maximum curl angle and the solvent concentration. Furthermore, several smart devices have also been fabricated, including the methanol-driven bionic petals, worm robot, alertor and LIG sensor. Therefore, such soft composites of flexible MOF and polymer have great potential in bio-robot and this work may provide new design strategy for the MOFs/polymer smart materials.
研究领域:
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2025
·
IF 2.9
Jiaqi Li,Yidan Zhang,Pingyu Luo,Chun Li,Fanming Zeng,Tiantian Sun,Hanhui Lei,Xiaoteng Liu,Chunbo Liu
Persulphate-based advanced oxidation technology efficiently and cost-effectively removes organic dyes from water but designing stable photocatalytic systems and understanding their reaction mechanisms remain key challenges. Metal–organic frameworks (MOFs) have attracted considerable research attention for degrading organic pollutants owing to their high porosity, tunable structure, and ease of modification. In this study, a series of M-MOF-74 (M = Co, Fe, Ni) photocatalysts are synthesized by a hydrothermal method for methylene blue (MB) degradation. Among them, the Co-MOF-74 photocatalytic synergetic peroxymonosulfate system exhibits high catalytic activity after 30 min of visible light irradiation. MB degradation efficiency reaches 94.8%, and the reaction rate constant is 0.210 min−1, which is approximately 19.44 times higher than the reaction rate constant of the original Co-MOF-74. Compared with Fe-MOF-74 and Ni-MOF-74, Co-MOF-74 exhibits better photocatalytic performance due to the dynamic changes in the valence state of cobalt, which more effectively facilitate the activation of PMS. In addition, this study analyses the possible degradation pathways of MB in water and toxicological evaluations of intermediate products, providing new insights for the effective removal of dyes in water.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2024
·
IF 4.9
Rui Gou,Yong Li,Qilong Chen,Sha Wang,Dan Sun,Changhua Li,Xianmin Gong,Yi He
Metal corrosion causes a lot of waste of resources, and the protection of metals from corrosion is becoming increasingly important. In this study, zeolite-imidazole (ZIF-67) was grown on the surface of Co-MOF for the first time by a one-step (complexation) method. 2-Mercaptobenzimidazole (MBI) was then loaded into the inner cavity of ZIF-67, resulting in the formation of a new composite material, Co-MOF@ZIF-67@MBI. The modified Co-MOF exhibits excellent interfacial compatibility with the water-based epoxy resin, and the Co-MOF@ZIF-67@MBI composite coating demonstrates robust anti-corrosion properties. Following a 60-day immersion period, the electrochemical experiment demonstrated that the corrosion resistance modulus of the Co-MOF@ZIF-67@MBI composite coating reached 10 8 Ω cm², indicating that the coating effectively enhanced the corrosion resistance of the coating and significantly extended the service life of the coating.
研究领域:
材料科学
·
腐蚀与防护
·
复合材料
✓ 已验证
产品关联
DOI
高影响因子
ACS Omega
·
2019
·
IF 2.584
Bo Lin,Aiyong Wang,Yanglong Guo,Yuanqing Ding,Yun Guo,Li Wang,Wangcheng Zhan,Feng Gao
Co-, Ni-, and Zn-containing MOFs are prepared and then pyrolyzed to generate materials for ambient temperature NO adsorption. Materials containing Co are much more efficient for NO adsorption than those containing Ni and Zn; therefore, Co is identified as the active phase. The best performing material studied here achieves 100% low concentration (10 ppm) NO adsorption for more than 15 h under a weight hourly space velocity of 120 000 mL g–1 h–1. Powder X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared, and Raman spectroscopies, along with scanning electron microscopy and TEM, are used to probe the physicochemical properties of the materials, particularly the Co active phase, and chemistries involved in NO adsorption–desorption. NO adsorbs on oxygen-covered Co nanoparticle surfaces in the form of nitrates and desorbs as NO at higher temperatures as a result of surface nitrate decomposition. NO storage capacity decreases gradually upon repeated NO adsorption–desorption cycles, likely because of Co3O4 formation during these processes.
研究领域:
材料科学
·
环境科学
·
化学工程
✓ 已验证
DOI
PubMed
高影响因子
Cell Reports Physical Science
·
2024
·
IF 7.9
Haiyang Wu,Yang Li,Langyuan Wu,Zhiwei Li,Yimin Xing,Dewei Xiao,Zengjie Fan,Xiaogang Zhang
Zinc-ion batteries (ZIBs) have faced persistent challenges related to dendrite growth and the hydrogen evolution reaction (HER). Herein, a metal-organic framework (MOF) polycrystalline membrane is introduced into the realm of ZIB research, motivated by the remarkable separation capabilities exhibited by MOF membranes. A MOF polycrystalline membrane is constructed on the Zn anode through liquid-phase epitaxial growth at room temperature. Aberration-corrected scanning transmission electron microscopy (AC-STEM) analysis unequivocally verifies the ingress of Zn 2+ into the MOF cavities, subsequently leading to the reconstitution of the solvation sheath. Profiting from the close contact between the membrane and the Zn anode, the Zn 2+ are reduced to Zn 0 directly in the cavities of the MOF after entering. This behavior effectively regulates the deposition trajectory of Zn 2+ and eliminates the potential for secondary solvation. Leveraging the efficient separation and ion-confinement capabilities of the MOF, the Zn anode incorporating the metal-azolate framework-4 (MAF-4) membrane demonstrates notable inhibition of the HER and suppression of dendrite formation.
研究领域:
材料科学
·
电化学
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
APPLIED ORGANOMETALLIC CHEMISTRY
·
2025
·Vol. 39
·期 5
·e70141
·
IF 0
Huan Zhang,Wen-Qi Jin,Peng Li,Wei Gao,Xiu-Mei Zhang
A highly efficient photocatalyst, the CdS/Mn-MOF composite, was synthesized by first preparing a new 2D Mn-MOF (Mn(L)·H 2 O, H 2 L = 5-(2-benzothiazolyl)isophthalic acid) precursor through the solvothermal method and subsequently growing CdS nanoparticles. X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), UV–vis spectroscopy, and other techniques were utilized to characterize the structural, morphological, textural, compositional, and optical properties of the composites. The prepared photocatalysts, designated as X-CdS/Mn-MOF (where X = 50, 25, and 10, represents the mass percentage of CdS), were tested for photocatalytic performance. Among them, the 50-CdS/Mn-MOF sample exhibits the optimized degradation efficiency of 99.1% for Rhodamine B (RhB, 20 mg/L) in 50 min under visible light irradiation, which is 7.3 times and 2.4 times higher than that of Mn-MOF and CdS, respectively. Various test results indicate that the improved photocatalytic activity of CdS/Mn-MOF composites can be attributed to the formation of heterojunctions. Specifically, the heterojunctions enhance the separation efficiency of photogenerated carriers and effectively suppress the recombination of electrons and holes, thereby improving the overall efficiency of the photocatalytic reaction. Moreover, the presence of heterojunctions optimizes the material's band structure, facilitating more efficient carrier transport, which further enhances photodegradation performance. Radical quenching experiments confirmed hydroxyl radicals (·OH − ) and superoxide radical anions (·O 2 − ) played dominant roles in the photodegradation process. Additionally, the composite material also demonstrates good stability and reproducibility. The research further provides evidence that the efficiency of dye degradation can be significantly improved by the rational design of composite catalysts consisting of other semiconductors and MOFs.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
APPLIED SURFACE SCIENCE
·
2021
·
IF 6.707
Mengyang Xu,Chao Sun,Xiaoxue Zhao,Haopeng Jiang,Huiqin Wang,Pengwei Huo
Fabricating the hierarchical heterostructure is efficient way for enhancing CO 2 conversion of semiconductor photocatalysts. Herein, a simple strategy has been employed to prepare several 3D hierarchical CdS/Ni-MOF heterostructure photocatalysts, and the selective photoreduction of CO 2 to CO under simulated sunlight in the gas–solid phase reactor. Among the prepared photocatalysts, 20%-CdS/Ni-MOF shows the best CO yield, which was 16 times and 7 times that of Ni-MOF and CdS, respectively. By controlling the morphology of the catalyst, we found that the significant improvement in photocatalytic activity can be ascribed to the synergistic effect of heterostructure in CdS/Ni-MOF and its unique hierarchical structure, which can improve the efficiency of charge transmission and provides abundant active sites, etc. Finally, the preliminary photocatalytic mechanism was discussed by in situ FTIR and liquid ultraviolet spectrophotometer.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）