FUEL
·
2024
·
IF 6.7
Xingyan Liu,Tianrong Xiong,Yonggang Xu,Kunhe Yang,Youzhou He,Haifeng Yang,Hong Wu,Jiajia Jing,Siqi Li,Siping Wei
Defect engineering for MOFs is a promising approach to accelerate the charge transfer to further enhance the photocatalytic performance. Up to now, the current defect engineering strategy for MOFs mainly focuses on a single adjustment mode with the apparent ceiling effect, whether the further break out of the ceiling effect could be achieved through the combination of two or more adjustment modes is still in its infancy. In this work, the original NH 2 -MIL-125 was firstly adjusted by a single adjustment mode in ethanol solvothermal method to obtain partially linker defective NM-125-X (where X signifies the distinct temperatures used in the solvothermal treatment, with optimal results observed at X = 120). Subsequently, the NM-125-120 was further re-regulated by adjusting the ligand defects through another adjustment mode in water heating agitation, resulting in the ultimate defective NM-125-120-65. The NM-125-120-65 obtained through double defect engineering avenue showed superior photocatalytic performance with the hydrogen production rate of 11585.23 μmol·g −1 , which was 1.23 and 14.05 times as those of partially defective NM-125-120 (9427.65 μmol·g −1 ) and original NH 2 -MIL-125 (824.85 μmol·g −1 ), respectively. In addition, the NO removal rate of NM-125-120-65 was 64.8 % also higher than that of NM-125-120 (37.8 %) and NH 2 -MIL-125 (23.6 %). Through a series of comparative experiments, especially TGA and XPS, it was noted that the ligand defective NH 2 -MIL-125 can be formed by ethanol solvothermal method, and it was also confirmed that through further re-regulating the ligand defects in water heating agitation, the linker defects could also be further expanded. The PL emission spectra, IT diagrams, and EIS measurements displayed that the NM-125-120-65 had outstanding conductivity and excellent electron mobility compared to NM-125-120 and NH 2 -MIL-125. This work provided a novel approach for the subsequent defect engineering by another adjustment mode based on the existing defective MOFs via double linker defect engineering adjustment modes, so as to further obtain better photocatalytic performance for solving the environmental and energy crisis.
研究领域:
材料科学
·
环境化学
·
能源化学
·
光催化
·
纳米材料
·
物理化学
✓ 已验证
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2020
·
IF 9.038
Shi-Wen Lv,Jing-Min Liu,Ning Zhao,Chun-Yang Li,Zhi-Hao Wang,Shuo Wang
Nowadays, designing highly active photocatalysts for pollutant degradation under visible light still remains a challenging problem. Herein, a novel benzothiadiazole functionalized Co-doped MOF-based photocatalyst with electron deficient unit was first synthesized via a feasible step-by-step assembly strategy. Benzothiadiazole, as typical electron deficient group, could effectively promote the separation and transfer of photoinduced charge carriers. The implantation of Co ion could be served as an effective mediator to further facilitate the charge transfer through a Co 3+ /Co 2+ redox pathway. Interestingly, the as-synthesized Co-MIL-53-NH-BT exhibited significantly enhanced photocatalytic degradation capacity for BPA and OFX under visible light irradiation, with removal efficiency as high as 99.9 % and 99.8 % within 120 min. TOC analysis suggested that majority of contaminants had been degraded into CO 2 and H 2 O. The important parameters influencing the photocatalytic activity were investigated, and the kinetics study was also conducted. The possible degradation pathways and the possible photocatalytic mechanism were proposed. More importantly, the as-synthesized Co-MIL-53-NH-BT showed good reusability, stability as well as universal applicability. To sum up, current work not only developed an efficient and visible-light active photocatalyst for treating organic-contaminated wastewater, but also afforded some novel insight into the utilization of benzothiadiazole in MOF-based photocatalyst towards improving photocatalytic activity.
研究领域:
环境科学
·
材料科学
·
化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
LANGMUIR
·
2025
·
IF 3.9
Yue Cao,Yanping Wang,Lirong Guo,Zhiyue Han,Haining Liu,Kaipeng Zhong,Shaoju Bian,Naicai Xu
A novel composite adsorbent, AMP@MIL-101(Cr), has been successfully synthesized by integrating ammonium phosphomolybdate (AMP) with the metal–organic framework MIL-101(Cr) for the efficient adsorption of rubidium ions (Rb+) from aqueous solutions. The results of structural characterizations confirmed that the crystalline framework of the adsorbent remained intact after Rb+ adsorption, indicating excellent structural stability. Adsorption kinetics, isotherm, and thermodynamics studies revealed that the adsorption process followed a single-layer chemisorption mechanism and was an endothermic reaction and spontaneous adsorption process with negligible influence from solution pH. The adsorbent exhibited a remarkable Rb+ adsorption capacity, reaching 69.4 mg·g–1 within 5 min in a solution containing 250 mg·L–1 Rb+ at 45 °C. In the Nanyi Mountain Oilfield, the adsorption rate of adsorbent for Rb+ (10.69%) exceeded that of other ions (Li+: 0.75%; Na+: 0; K+: 0.95%; Mg2+: 0.67%). Furthermore, the adsorbent still maintained 86.72% of its initial adsorption capacity after 5 consecutive adsorption–desorption cycles. These findings highlighted the great potential of AMP@MIL-101(Cr) as an efficient and stable adsorbent for the selective recovery of rubidium from aqueous environments.
研究领域:
环境科学
·
材料科学
·
化学工程
·
吸附技术
·
无机化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Zhu Gao,Jiaxing Wang,Yaseen Muhammad,Peng Hu,Yang Hu,Zhe Chu,Zhongxing Zhao,Zhenxia Zhao
Competitive adsorption of volatile organic compounds (VOCs) under high humidity is a critical but challenging issue in the applications of metal–organic frameworks (MOFs). In this work, hydrophobic-shell structured NH 2 -MIL(Ti)-125@mesoporous carbon composite was designed to enhance selective adsorption towards VOCs under humid conditions via confined growth strategy. Ti-clusters were first anchored into pores of ordered mesoporous carbon (OMC), and then confined grown into NH 2 -MIL(Ti)-125 via ‘ship-in-the-bottle’ approach. Hydrophobic shell of OMC concurrently protected the adsorption sites on NH 2 -MIL(Ti)-125 from H 2 O occupation and enhanced affinity towards non-polar toluene. Moreover, the resulting composited supplied abundant diffusion channels for toluene thereby accelerated the mass transfer though mesopores (OMC) and micropores (MOFs). As expected, the hydrophobic-shell NH 2 -MIL(Ti)-125@OMC composite efficiently enhanced hydrophobic property and toluene adsorption affinity. It obtained a dramatical increase in toluene adsorption capacity (3.86 mmol/g at 0.001 P / P 0 ) about 7.4 times of NH 2 -MIL(Ti)-125, and a 29% decrease in water vapor adsorption capacity (0.30 g/g at 1 mbar), which much superior than many reported expensive adsorbents. In addition, the composite induced more confined micropores to mesopores interconnected structure in MIL(Ti)@OMC Ti , and hence facilitated toluene diffusion. The toluene rate constant of pseudo-second-order adsorption ( k a ) on the MIL(Ti)@OMC Ti was up to 0.12 g/(mmol∙min), which was 1.2–2.0 times higher than those of the MIL(Ti) species. Moreover, breakthrough curve indicated that MIL(Ti)@OMC Ti showed 1.5 times of toluene working capacity with faster diffusivity at 80% RH compared to pure NH 2 -MIL(Ti)-125, while the latter exhibited much lower value of Q w / Q e than that of the former. This work provides a novel composite strategy for hydrophobic MOFs construction, and deeper understanding for VOCs/H 2 O competitive adsorption on MOFs composites in large scale applications.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
FOOD CHEMISTRY
·
2025
·
IF 9.8
Zhiyang Qin,Tianyue Peng,Xinguang Qin,Gang Liu,Haizhi Zhang
Accurate detection of tetracycline residue is of great significance for ensuring product quality and protecting human health. Here, a colorimetric/fluorescent dual-mode biosensor was developed for the detection of tetracycline in honey by using metalloporphyrin [TCPP(Fe)] covalently modified NH 2 -MIL-101(Fe) [named NH 2 -MIL-101(Fe)@TCPP(Fe)]. The morphology, chemical structure and peroxidas-like activity of this hybrid nanozyme were comprehensively studied. Based on excellent catalytic activity and intrinsic fluorescence of NH 2 -MIL-101(Fe)@TCPP(Fe), a colorimetric/fluorescent dual-mode biosensor was developed for the detection of tetracycline. The primary mechanism for this dual mode biosensor was the inhibitory effect of tetracycline on on NH 2 -MIL-101(Fe)@TCPP(Fe) catalyzed chromatic reaction between H 2 O 2 and 3,3′,5,5′-tetramethylbenzidine (TMB)/ o -phenylenediamine (OPD), which was ascribed to the consumption of · OH by tetracycline and the adsorption of tetracycline on the surface of NH 2 -MIL-101(Fe)@TCPP(Fe). After effective validation, this colorimetric/fluorescent dual mode method was applied to detect tetracycline residues in three actual honey samples.
研究领域:
生物化学
·
分析化学
·
食品安全检测
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYST
·
2020
·Vol. 146
·期 4
·1295-1302
·
IF 3.978
Defen Feng,Fucun Wei,Yeyu Wu,Xuecai Tan,Fang Li,Yongkuai Lu,Gaochao Fan,Heyou Han
An ultrasensitive electrochemiluminescence (ECL) biosensor was developed based on MIL-53(Al)@CdS QDs and SiO2@AuNPs for trichlorfon detection. Metal–organic frameworks (MOFs) were used as a loading platform that provided a large surface area to load targets and modified materials onto the electrode. At the same time, SiO2@AuNPs loaded plenty of AuNPs which effectively increased the ECL resonance energy transfer between the CdS QDs, so that the ECL signal was strongly quenched and resulted in an amplified response. In the range of 10−11–10−4 M, the ECL response showed a linear relationship with the concentration (logarithm) of trichlorfon, and the detection limit was 5.1 × 10−12 M (S/N = 3). When the biosensor was applied to detect trichlorfon in lettuce, broccoli, cucumber, and chives, the recoveries obtained from the spiked samples were 97%–105%, 102%–104%, 100%–104%, and 98%–104%, respectively. Thus, this novel ECL biosensor has potential applications for the analysis of trichlorfon in food samples.
研究领域:
分析化学
·
环境科学
·
材料科学
·
食品安全
✓ 已验证
DOI
PubMed
高影响因子
Small
·
2024
·Vol. 20
·期 27
·2309541
·
IF 13
Tingting Liu,Kaiyue Hu,Yansheng Li,Yanhong Wang,Dongmei Han,Zhihua Wang,Fubo Gu
The Z-scheme MIL-88B/BiOBr (referred to as M x B y , whereas x and y are the mass of MIL-88B(Fe) and BiOBr) heterojunction photocatalysts are successfully prepared by a facile ball milling method. By adding low concentration H 2 O 2 under visible light irradiation, the Z-scheme heterojunction and photocatalytic-Fenton-like reaction synergistically enhance the degradation and mineralization of ciprofloxacin (CIP). Among them, M50B150 showed efficient photodegradation efficiency and excellent cycling stability, with 94.6% removal of CIP (10 mg L −1 ) by M50B150 (0.2 g L −1 ) under 90 min of visible light. In the M x B y heterojunctions, the rapid transfer of photo-generated electrons not only directly decomposed H 2 O 2 to generate · OH, but also improved the cycle of Fe 3+ /Fe 2+ pairs, which facilitated the reaction with H 2 O 2 to generate · OH and · O 2 − radicals. In addition, the effects of photocatalyst dosages, pH of CIP solution, and coexisting substances on CIP removal are systematically investigated. It is found that the photocatalytic- Fenton-like reaction can be carried out at a pH close to neutral conditions. Finally, the charge transfer mechanism of the Z-scheme is verified by electron spin resonance (ESR) signals. The ecotoxicity of CIP degradation products is estimated by the T.E.S.T tool, indicating that the constructed photocatalysis-Fenton-like system is a green wastewater treatment technology.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2025
·
IF 6.9
Yue Wang,Wenjun Zhang,Yanjun Zhang,Meng Chen
Metal-organic frameworks (MOFs), with tunable morphologies and porous architectures, show great potential in photocatalysis. A variety of MOFs can be synthesized by changing the types of metal ions and organic ligands. However, fewer studies have explored the influence of the metal-to-ligand molar ratio on the catalytic performance of the resulting MOF-related products. In this work, capsule-shaped NH 2 -MIL-68(In)/InOOH composites were synthesized by adjusting molar ratios of In(NO 3 ) 3 to 2-aminoterephthalic acid. Time-dependent characterization revealed sequential crystallization: rod-shaped NH 2 -MIL-68(In) initially formed in the solution, followed by the in-situ growth of InOOH nanowires on its surfaces via excess indium ions, ultimately constructing a Z-scheme heterojunction. The optimized NM/InOOH (8:1) composite exhibited a larger specific surface area and extended light absorption. The Z-scheme configuration significantly promoted charge carrier separation efficiency while maintaining strong redox potentials of the photoinduced holes and electrons, thereby resulting in 5–8-fold improvement in degradation rates for four dyes (AOII, RhB, MB, and Rh6G), highlighting its broad photocatalytic applicability.
研究领域:
材料科学
·
纳米技术
·
环境科学
·
光催化
·
无机化学
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2025
·
IF 7.2
Yisha Zheng,Shuoling Lei,Wenjie Guo,Wenlong Xiang,Yanmei Chen,Yanhui Zhang
The high toxicity and persistence of nitroaromatic pollutants pose a serious threat to aquatic ecosystems. In this study, inert SiO 2 was employed as an "inactive enhancer" to construct core-shell MIL-125-NH 2 @ZIF-67/SiO 2 (M@Z/SiO 2 ) heterogeneous MOF catalysts via an epitaxial-wet impregnation method, enabling the efficient reduction of p -nitrophenol ( p -NP) under ambient temperature and pressure. Although SiO 2 itself lacks catalytic activity, the micro-mesoporous network it forms effectively disperses Co active sites and prevents their aggregation. The conversion rate of p -NP increased from 92.5% to 98.4% within 6 min and retained 98% activity after three consecutive cycles. Moreover, the catalyst exhibited excellent stability across a wide pH range (3-11) and in various anionic environments. Mechanistic studies revealed that the interfacial electron transfer between ZIF-67 and MIL-125-NH 2 significantly reduces the activation energy barrier of NaBH 4 . Additionally, the incorporation of SiO 2 not only enhances the mechanical stability of the composite but also optimizes pore structure and substrate mass transfer by modulating surface hydrophilicity. This work provides valuable insights for the precise design of MOF-on-MOF heterostructures and the synergistic engineering of interfacial and surface properties in environmental catalytic materials.
研究领域:
环境科学
·
催化
·
材料化学
·
纳米技术
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Ying Jiang,Hao Lu,Lingli Lei,Daniel Scherman,Yingshuai Liu
The design of nanomedicines targeting specific tumor microenvironment (TME) characteristics, such as low pH, hypoxia, and elevated glutathione (GSH) concentration, holds significant potential for selectively killing cancer cells. In this study, we have developed a TME-responsive nanoparticle, i.e. , MIL-53(Fe)@MnO 2 stabilized with polyethylene glycol (FMP), which is capable of depleting GSH and sustainably generating hydroxyl radical (•OH) for enhanced chemodynamic therapy of cancer. After endocytosis, the FMP nanoparticles undergo gradual decomposition, resulting in GSH depletion while releasing Fenton-active Fe 2+ and Mn 2+ ions. These ions then subsequently catalyze a Fenton-like reaction to generate highly toxic •OH, ultimately inducing oxidative cell death. As a synergistic effect, the depletion of GSH further enhances therapeutic efficacy by inhibiting intracellular •OH scavenging. In vivo experiments demonstrated that this synergistically chemotherapeutic approach efficiently suppressed tumor growth without inducing significant systemic toxicity. This work presents a promising nanotherapeutic strategy that simultaneously depletes intracellular GSH and sustains cytotoxic •OH generation for enhanced tumor treatment.
研究领域:
纳米医学
·
癌症治疗
·
生物无机化学
·
活性氧治疗
·
靶向药物递送
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYTICA CHIMICA ACTA
·
2021
·
IF 6.558
Jiabi Xu,Yanyan Xing,Yutong Liu,Mingzhe Liu,Xiaohong Hou
In recent decades, artificial nanozymes with excellent stability, low cost and availability have been gradually explored to avoid the limits of natural enzymes such as poor stability, high cost and difficult preparation. Herein, for the first time, we investigated the capability of nanoscale Fe 3 O 4 @MIL-100(Fe) as a nanozyme, which was quickly synthesized in situ by a microwave-assisted method within 20 min using Fe 3 O 4 as the metal precursor. The obtained Fe 3 O 4 @MIL-100(Fe) showed satisfactory intrinsic dual enzyme mimetic activities, including peroxidase (POD)- and catalase (CAT)-like activities. Moreover, a simple and effective colorimetric biosensor was fabricated to detect glutathione (GSH) based on its POD-like activity. The proposed measurement had a linear range of 1–45 μM and a limit of detection (LOD) of 0.26 μM (3.3 δ/S). It was proved that the established colorimetric sensing system could be successfully applied to detect GSH in actual biological samples. Importantly, the outstanding reusability and stability made it extremely valuable as a catalyst. The present work implied that Fe 3 O 4 @MIL-100(Fe) synthesized in situ by the microwave-assisted method was a very promising candidate for biocatalyst and biosensing.
研究领域:
纳米生物技术
·
分析化学
·
生物传感
·
酶模拟
·
分子诊断
·
转化医学
✓ 已验证
DOI
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2018
·
IF 3.649
Tongtong Wang,Xuedan Song,Qunxing Luo,Xiaodong Yang,Siying Chong,Jie Zhang,Min Ji
In terms of ‘green chemistry’ and ‘atom economy’, the cycloaddition of CO 2 to yield cyclic carbonate without any additive is an eco-friendly way to utilize CO 2 . Unfortunately, the low CO 2 capture quantity of common catalysts limited its catalytic efficiency. Herein, a novel acid-base bifunctional catalyst was successfully prepared by immobilizing ionic liquid on MIL-101-NH 2 (IL/MIL-101-NH 2 ) and tested for propylene carbonate (PC) rapid and facile synthesis from CO 2 and propylene oxide (PO). The synergetic interaction between Lewis base with strong CO 2 chemical capture capacity and Brønsted acid with strong hydrogen bond donor leads to the high catalytic efficiency of IL/MIL-101-NH 2 for carbonate synthesis from CO 2 and PO without any additive. The immobilization mode between MIL-101-NH 2 and IL is energetically supported by the density functional theory (DFT) calculations. This design idea of specific catalyst and the acid-base synergetic strategy provides new insights into the design of powerful catalyst systems for the CO 2 conversion.
研究领域:
催化化学
·
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）