APPLIED SURFACE SCIENCE
·
2021
·
IF 6.707
Ya-yun Li,Qiuming Zou,Zhangjian Li,Dong Xie,Yuan Niu,Jizhao Zou,Xierong Zeng,Junfeng Huang
Bimetallic electrocatalysers have attracted dramatic attentions in recent years owing to their unique electronic configuration, charge transfer efficiency and synergistic effect. Ni-Fe based alloys are considerable as one of the most promising materials with superior electrocatalytic performance since the outstanding oxygen reaction activity of iron and the strong capability of nickel. Herein, Ni-Fe MOF derived Ni-Fe alloys embedded graphitic carbon electrocatalyst is synthesized as bifunctional oxygen electrocatalyst with hierarchical porous structure and superior oxygen reaction electrocatalytic performance. The onset potential and the half-wave potential of Ni 0.6 Fe 0.4 CM in oxygen reaction are 0.88 V and 0.75 V, respectively, which are superior than those of commercial Pt/C. Furthermore, a low overpotential of 320 mV at 10 mA/ cm 2 is obtained in oxygen evolution reaction, which is well consistent with that of commercial RuO 2 . In the meantime, excellent long-term stability and anti-methanol ability endow Ni 0.6 Fe 0.4 CM exhibiting brilliant electrocatalytic performance as commercial Pt/C and RuO 2 . The assembled Zn-air battery exhibits smaller voltage gap (0.76 V) than that for commercial Pt/C and RuO 2 , and it has remarkable stability around 170 cycles in the discharge–charge test. These results summarize the merits of bimetallic electrocatalysers for bifunction electrochemical performance and promote the development of electrocatalytic applications.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2019
·
IF 8.355
Jizhi Zhou,Pei Liu,Zeyuan Liu,Jia Zhang,Xin Huang
The recovery of phosphorus (P) from wastewater has attracted substantial attention with the atrophy of global P resource. In the current work, the simultaneous recovery of P with the removal of nickel (Ni) via iron/activated carbon (Fe/AC) and hydrogen peroxide (H 2 O 2 ) form nickel-plating wastewater was achieved. The isotherm reaction showed a maximum P recovery of 99.99% with an equilibrium concentration of P of 0.12 mg/L, which was lower than the limitation of discharge regulation (China national regulation, 0.5 mg/L). The optimal conditions for P recovery were 0.25 mol/L H 2 O 2 , a Fe/AC mass ratio of 1:1, an at 60 °C, which led to the ratio of P in the form of FePO 4 in the residue to be 77%. Moreover, the Fe/AC microelectrolysis coupling to H 2 O 2 promoted Fe 2+ production from Fe 0 and improved the circulation of Fe 2+ , which improved the production of hydroxyl radicals with increasing pH and consequently enhanced oxidation efficiency of hypophosphite. The FePO 4 was found the major form of phosphate in the precipitate. The highest removal rate of nickel was 89%, which was attributed to its precipitation at high pH and adsorption on to iron hydroxides and activated carbon. Nickel purification was achieved by further coagulation as the equilibrium concentration of Ni was lower than 0.1 mg/L. Therefore, our work provides a promising approach for simultaneous recovery of P and removal of Ni from electroplating wastewater.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2019
·
IF 3.131
Jiang-Bo Huo,Kiran Gupta,Changyong Lu,Hans Chr. Bruun Hansen,Ming-Lai Fu
Efficient removal of aqueous arsenic is still a great challenge in particular for producing clean drinking water and for waste water treatment. To this end, a novel magnetic porous Fe-La composite, comprising La 2 O 2 CO 3 and Fe 2 O 3 , was fabricated via a self-sacrificing template method based on bimetallic (Fe, La)-MOFs calcined at 550 °C. Batch adsorption results demonstrated that Fe-LaXY (X and Y represent the feeding mole ratio of Fe and La precursors) exhibited a maximum adsorption capacity of As(V) (241, 251 and 410 mg g −1 for Fe-La51, Fe-La21 and Fe-La11, respectively), and they also showed satisfactory adsorption kinetics, which can be ascribed to a strong coordination between La and arsenate species. Coexisting sorbates including carbonate, silicate, sulfate, and humic acid had a slight influence on adsorption performance of arsenate, while phosphate isostructural to arsenate gave severe interference. More importantly, the Fe-La11 could be easily separated from water due to its magnetism (7.0 emu g −1 ), and it also exhibited excellent recyclability (above 80% of removal efficiency at the fifth cycle) as well as stability in terms of release of Fe and La ions (< 0.5 mg L −1 at pH 4.0–10.0). Based on results from X-ray photoelectron spectroscopy (XPS), Powder X-ray diffraction (PXRD) and Raman spectroscopy, it is demonstrated that ligand exchange of surface hydroxyl groups and the formation of inner-sphere surface complexes are main responsible for the As(V) removal mechanism. Combining the magnetic properties, the absorption properties and the recyclability make Fe-LaXY derived from bimetallic MOFs promising sorbents for arsenate removal.
✓ 已验证
产品关联
DOI
高影响因子
BIORESOURCE TECHNOLOGY
·
2019
·
IF 6.669
Juanli Liu,Baiqin Zhou,Hong Zhang,Juan Ma,Bin Mu,Wenbo Zhang
A novel wasted sludge-based Biochar modified by Chitosan and Fe/S (BCFe/S) was prepared for tetracycline (TC) removal from water. To investigate the similarities and differences in adsorption behaviors between Biochar and BCFe/S, characterization, kinetics, isotherms and thermodynamics were discussed. The studies on site energy distribution (SED) were also presented. The results showed that the maximum TC adsorption amount was 51.78 mg/g for Biochar, while it was 183.01 mg/g for BCFe/S-4. Meanwhile, electrostatic attraction, π-π stacking, pore filling, silicate bonding and hydrogen bonding were the main adsorption mechanisms for TC removal by Biochar. Besides above mechanisms, chelating and ion exchange were also accounted for adsorption mechanisms for TC uptake by BCFe/S-4. Moreover, SED results revealed that the surface of Biochar was more homogeneous while the surface of BCFe/S-4 was more heterogeneous at higher temperature. Findings of this work could offer valuable information in designing adsorbents and investigating adsorption mechanisms.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COMBUSTION AND FLAME
·
2019
·
IF 4.12
Long Cheng,Hongtao Yang,Yue Yang,Yifan Li,Yingyi Meng,Yanchun Li,Dongming Song,Houhe Chen,Ramón Artiaga
The application of boron in fuel-rich solid propellant is limited by its long combustion time, ignition delay and low combustion efficiency. To overcome these problems, B/Nitrocellulose (NC)/Fe particles were fabricated by electrospraying. The reactivity and combustion behavior of B/NC/Fe particles were characterized by TG/DSC, oxygen bomb calorimeter and laser ignition. Compared with pure boron, lower oxidation temperature was observed in the thermal analysis of prepared particles. Meanwhile, the prepared particles released more heat and ignite more readily during the combustion. Furthermore, B/NC/Fe particles were added into Hydroxyl-terminated polybutadiene (HTPB)/Ammonium perchlorate (AP) propellants as additives to test their combustion performance. The burning rate of propellants in air and closed bomb were both improved by 8.20% and 117%, respectively. Overall, B/NC/Fe particles not only show the superior reaction performance, but also contribute to the tunable burning rate of propellants.
✓ 已验证
产品关联
DOI
高影响因子
NANOTECHNOLOGY
·
2019
·Vol. 31
·期 1
·015101
·
IF 3.399
Keke Du,Qianqian Liu,Mei Liu,Rongmu Lv,Nongyue He,Zhifei Wang
Increasing the content of reactive oxygen species (ROS) with the assistance of nanoformulations in cancer cells via the Fenton reaction is considered an effective method to treat cancer. However, the efficiency of the Fenton reaction is affected by the level of H2O2, the selection of iron ions in different nanoformulations, etc. Herein, we use FeIII-tannic acid (FeIIITA) nanocomposites as the carrier to deliver glucose oxidase (GOD) which can solve the problem of insufficient endogenous H2O2 by catalytically converting the glucose. In comparison with traditional Fe2+/Fe3+, FeIIITA nanocomposites perform higher catalytic activity in converting H2O2 to high toxic hydroxyl radicals (·OH) due to the TA-mediated reduction of Fe3+. So, the integration of GOD and TA in the construction of nanocomposites significantly enhances the efficiency of the Fenton reaction. In vitro experiments show that ·OH produced by GOD-FeIIITA nanocomposites can not only achieve a good anticancer effect at a low concentration but also promote degradability of the nanocomposites. When it is only 1.08 μg · ml−1, the cell apoptosis rate has reached 76.91%. In vivo experiments further demonstrate that GOD-FeIIITA nanocomposites can significantly inhibit tumor growth. So this work lays a good foundation for Fenton reaction-based cancer treatment.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF ELECTRONIC MATERIALS
·
2019
·Vol. 49
·期 2
·1043-1050
·
IF 1.676
Jiao Yunpeng,Han Yinghui,Pang Yiheng,Zhou Junxiu,Qi Xiaohan,Liu Yunpeng
Abstract Some kinds of the plate-like hexagonal layered double complex hydroxides (named Ni-Fe-Sr-LDHs) materials were prepared for energy storage electrodes in this work. It showed good properties with energy densities and cycle life through the electrochemical tests. At 1 A g −1 current density, the specific capacitance of the electrode reached 311.02 F g −1 when the electrolyte was 6 M LiOH. In the long cycle test, the capacitance retention of the electrode maintained at 73.16% after 2000 cycles (current density: 1 A g −1 ). The morphologies of Ni-Fe-Sr-LDHs were characterized via the scanning electron microscope, transmission electron microscopy and x-ray powder diffraction. The prepared layered double hydroxides were further optimized by doping carbon nanotubes (CNTs). The optimal weight ratio of Ni-Fe-Sr-LDHs to CNTs was 3:1. The specific capacitance in the measurement of galvanostatic charge–discharge increased to 438.74 F g −1 , and the stability of long-term cycling was raised to 77.45%. These results indicated that Ni-Fe-Sr-LDHs combined with CNTs would be an ideal electrode material for practical energy storage. Graphic Abstract
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2019
·
IF 4.084
Jianshuo Zhang,Kun Hou,Qianqian Yao,Chuxin Wu,Meihua Huang,Lunhui Guan
Transition metal phosphides represent a class of promising electrocatalysts for electrochemical water oxidization and other energy conversion reactions. In this work, we report a novel seal strategy, followed by a second step phosphorization treatment, produces Ni-Fe-P heterostructure directly grown on nickel foam that shows highly catalytic activity for electrochemical water oxidation . The as-prepared catalyst exhibits an excellent electrocatalytic activity , manifested by a current density of 20 mA cm −2 with a very low overpotential (260 mV) for oxygen evolution reaction along with an extremely small Tafel slope of 27 mV decade −1 and a very excellent durability of 120 h in alkaline solution. The excellent performance with exceptional durability owe much to the synergistic effect between the Ni-Fe-P heterostructure and the outer oxidized layer. Remarkably, a current density of 10 mA cm −2 was reached at a low cell voltage of 1.63 V when the original electrode and surface oxidized electrode are used as cathode and anode , respectively.
✓ 已验证
产品关联
DOI
高影响因子
HYDROMETALLURGY
·
2019
·
IF 3.465
Guang-jin Zhu,Hai-yan Tang,Hong-ling Zhang,Li-li Pei,Peng Zhou,Yi-lang Shi,Zai-hua Cai,Hong-bin Xu,Yi Zhang
An ion-imprinted polymer (IIP) was synthesized by radical copolymerization for use in the removal of trace Fe(III) ions from Cr(III)-containing solutions. During the synthesis process, Fe(III) ions, acrylic acid and ethylene glycol dimethacrylate were employed as the template ions, functional monomer and cross-linker, respectively. The optimal mole ratio of acrylic acid to Fe(III) ions, which significantly affected the adsorption performance, was determined. The maximum static adsorption capacity of the polymer for Fe(III) ions was 114.25 mg g −1 , with a selective factor ( k ) of 492.18 and a relative selective factor ( k′ ) of 50.87 for Fe(III)/Cr(III). The Fe(III) ions removal efficiency could reach 94.43%, leading to a final Fe(III) concentration of 0.053 mg L −1 in the treated solution. After the removal process, the mass ratio of Cr(III) ions to Fe(III) ions was higher than 26, 000:1 in the solution, with an initial mass ratio of Cr(III) to Fe(III) ions of 1500:1.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THE ELECTROCHEMICAL SOCIETY
·
2019
·Vol. 166
·期 4
·E69
·
IF 3.12
Li Xu,Ye Wang,Qiutong Xu,Huiying Duan
Ti/SnO2-Sb-Fe electrodes have been prepared by a novel precipitation printing method, the traditional sol-gel method, and the direct current deposition method. The microstructure of the electrodes was systematically characterized through X-ray diffraction (XRD) observation and high-resolution transmission electron microscopy (HRTEM) verification. In addition, the morphology was characterized by scanning electron microscopy (SEM), while the electrochemical properties and the stability were further investigated by cyclic voltammetry (CV), linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS), and accelerated life testing. The results indicate that the Ti/SnO2-Sb-Fe electrode prepared by precipitation printing has the smallest nanoparticle structure (< 10 nm), a higher electrochemical porosity (49.6%), and a higher oxygen evolution potential (2.20 V). As a comparison, the Ti/SnO2-Sb-Fe electrode prepared by the sol-gel method has the longest service life. To further evaluate the electrocatalytic activity of the Ti/SnO2-Sb-Fe electrodes, Acid Red 73 was employed as simulated sewage for electrochemical degradation. After 180 min, the removal efficiency of AR 73 reached 86.8%, 63.4%, and 74%, respectively, for Ti/SnO2-Sb-Fe electrodes prepared by precipitation printing method, traditional sol-gel method, and direct current deposition method. Furthermore, the degradation of AR 73 followed pseudo-first-order kinetics.
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2019
·Vol. 26
·期 9
·8768-8778
·
IF 2.914
Sun Yufeng,Liu Zongtang,Fei Zhenghao,Li Changshun,Chun Yuan,Zhang Aimin
Fe-Ni bimetallic nanoparticles supported on CNTs (Fe-Ni/CNTs) were synthesized, characterized, and applied for removal of 2,4-dichlorophenol (2,4-DCP) in aqueous solution. The removal performance was enhanced drastically on Fe-Ni/CNTs with respect to monometallic Fe/CNTs. The synergistic effect between Fe-Ni nanoparticles and CNTs has been studied in detail. The research results indicated that the doping of Ni played an important role in promoting the catalytic degradation of 2,4-DCP. And the presence of CNTs not only could effectively reduce the aggregation of nanoparticles but also facilitate the mass transfer of 2,4-DCP and the formation of active atomic hydrogen during the catalytic process. In addition, the removal kinetics of 2,4-DCP by Fe-Ni/CNTs were in agreement with a pseudo-first-order model, and the rate constants were dependent on a number of factors including the initial concentration of 2,4-DCP, the dosage of Fe-Ni/CNTs, pH value of the solution, and doping amount of Ni. The degradation mechanism involved the adsorption by CNTs and catalytic reduction by Fe under the stimulating of Ni, and the preferred dechlorination followed the order of para-Cl > ortho-Cl. The study confirmed that Fe-Ni/CNTs had a potential to be a promising catalytic material for removal of chlorophenol and had a great prospect for practical application.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2019
·
IF 4.084
Huiming Li,Yang Wang,Wei Zhu,Zhongbin Zhuang
Searching for low-cost electrocatalysts with high activity towards the hydrogen evolution reaction (HER) is of great significance to enable large-scale hydrogen production via water electrolysis . In this study, by using inverse spinel MFe 2 O 4 (M = Mn, Fe, Co, Cu) nanoparticles (NPs) as the precursors, monodisperse bimetallic phosphide M-Fe-P NPs/C with hollow structures were readily obtained by a gas-solid annealing method. These hollow phosphide NPs displayed excellent HER activity in an acidic medium with a low loading amount of 0.2 mg cm −2 . In particular, the Co–Fe–P NPs/C shows highest HER activity that only requiring an overpotential of 97 mV to retain a current density of 10 mA cm −2 . A volcano relation between activity and incorporated elements was revealed. Incorporation of cation with high electronegativity stabilized the FeP active centres, while phase segregation resulted in the loss of activity for Cu–Fe–P NPs/C.
✓ 已验证
产品关联
DOI
高影响因子