CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Decai Huang,Sisi Liang,Dejian Chen,Jie Hu,Kunyuan Xu,Haomiao Zhu
The emerging applications of near-infrared (NIR) spectroscopy technology in medicine and food security call for compact and efficient NIR light source such as NIR phosphor converted LEDs (pc-LED). Currently, most of the NIR phosphors suffer from low photoluminescence (PL) quantum yield and poor thermal or chemical stability. Herein, a fluoride garnet NIR Na 3 Al 2 Li 3 F 12 :Cr 3+ phosphor was successfully synthesized via coprecipitation method. It can be excited efficiently by blue or red light and shows a broad emission band covering 650–1000 nm (bandwidth of ~110 nm) with a PL quantum yield of 78%. The fine electronic structure of Cr 3+ ions in the host was revealed by the measurement of temperature-dependent (8–300 K) excitation and emission spectra analysis. Particularly, at 423 K, the Na 3 Al 2 Li 3 F 12 :5%Cr 3+ sample retained ~99% of the PL intensity at room temperature, exhibiting excellent PL thermal stability. A NIR pc-LED was fabricated by combining the Na 3 Al 2 Li 3 F 12 :5%Cr 3+ phosphor with a commercial blue LED chip, and radiant flux of 14.3 mW in NIR region was obtained at 60 mA drive current. Furthermore, the penetration of NIR light generated by this pc-LED in chicken breast was reached. The results suggested that Na 3 Al 2 Li 3 F 12 :Cr 3+ is a promising candidate for broadband pc-LED in NIR spectroscopy applications.
研究领域:
材料科学
·
光学工程
·
生物医学光子学
·
半导体器件
·
分析化学
✓ 已验证
DOI
高影响因子
MATERIALS LETTERS
·
2014
·
IF 2.269
Yaguang Yuan,Yanping Yuan,Nan Zhang,Yanxia Du,Xiaoling Cao
Capric–myristic–palmitic acid ternary eutectic mixture (CA–MA–PA) was prepared as phase change material (PCM). A novel composite PCM of CA–MA–PA/expanded graphite (EG) with an optimum mass ratio (CA–MA–PA:EG=13:1) was prepared by uniformly absorbing CA–MA–PA into the porous network structure of the EG. The melting and freezing temperatures of CA–MA–PA/EG composite PCM were measured by differential scanning calorimeter as 18.61 °C and 16.58 °C, respectively, while the melting and freezing latent heats were 128.2 J/g and 124.5 J/g, respectively. The thermal conductivity of the CA–MA–PA/EG composite PCM was measured as 3.67 W/m K and thus the thermal storage and release rates were significantly increased. The thermal cycling test results showed that CA–MA–PA/EG composite PCM has a good thermal reliability. All the above results show that the CA–MA–PA/EG composite PCM is a potential solution for latent heat storage system.
研究领域:
材料科学
·
能源化学
·
热物理
·
功能材料
·
储能技术
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2022
·
IF 6.371
Zuocheng Luo,Qingfeng Zhang,Wei Xie,Tong Yuan,Qisheng Zang,Ning Wang,Hanxiao Fan,Shuhong Xie,Xiaoping Ouyang
Potassium ion hybrid capacitors (PIHCs) have attracted widespread attention as combining the advantages of potassium ion batteries (PIBs) with supercapacitors . However, the sluggish kinetics caused by the large radius of K + hinder the practical application of PIHCs. Herein, we synthesized a boron and fluorine co-doping interlaced network porous carbon nanofibers (BF-PCNFs), which was used as the freestanding anode of PIHCs the freestanding anode of PIHCs to alleviate large volume expansion and increase conductivity. Benefiting from the B, F co-doping and porous interlace nanostructure of BF-PCNFs, the anode shows 185 mA h g −1 under a load of 12.6 mg cm −2 , a reversible capacity of 176 mA h g −1 at 1000 mA g −1 after 6000 cycles, and the capacity retention from 100 mA g −1 to 5000 mA g −1 is 62%. Furthermore, the PIHCs based on BF-PCNFs as anode and activated carbon as cathode exhibit an energy density of 87 Wh kg −1 and a power density of 393 W kg −1 . The capacity retention is as high as 78% over 4000 cycles. Considering the exceptional rate performance, long cyclability and high-mass-loading, our work may supply a new strategy for designing novel energy storage devices with outstanding performance.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米科技
·
功能材料
✓ 已验证
DOI
高影响因子
MATERIALS RESEARCH BULLETIN
·
2024
·
IF 5.3
C. Wang,X.Z. Zheng,L. Yue,P.J. Xia,M. Xu,W.B. Dai
The exploration of stable/efficient phosphor for n -UV chip pumped white light-emitting diodes ( w LEDs) remains an arduous task. Herein, a novel series of color tunable Eu 2+ /Tb 3+ /Sm 3+ tridoped Sc-based cyclosilicate phosphors (KBaScSi 3 O 9 : Eu 2+ /Tb 3+ /Sm 3+ ) have successfully designed and obtained via facile solid-state reaction based on comprehensive consideration of rigidly structural network of host, weak electron-phonon coupling strength and spectral adjustability of codopants via energy transfer (ET). The crystallographic occupancies of Eu, Tb and Sm primary in Ba/K, Ba and Ba sites in the monoclinic host, respectively were determined on the basis of the Rietveld refinements and crystal chemistry rules. The photoluminescence (PL) properties were systematically investigated in conjunction with structural analyses, implying that the ‘warm’ white light with excellent thermal stability is stemmed from combination of optimized blue (Eu 2+ ), green (Tb 3+ ) and red (Sm 3+ ) emissions via Eu → Tb → Sm ET strategy. Interestingly, Tb ions play both roles of green light luminescent center and ET bridge to achieve cascade ET for connecting Eu/Sm ion pairs because of the adverse metal-metal charge transfer (MMCT) effect (Eu 2+ + Sm 3+ → Eu 3+ + Sm 2+ ). Furthermore, the phosphor-converted w LEDs (pc- w LEDs), by encapsulating the optimal KBS: 4 %Eu/4 %Tb/6 %Sm with commercial n -UV LED chip, show high thermal stability with satisfactory electroluminescence (EL) performances. These results indicate the KBS: Eu/Tb/Sm phosphors are potential candidates for application in high power n -UV pumped pc- w LEDs.
研究领域:
材料科学
·
发光材料
·
固态照明
·
无机化学
·
光电子学
✓ 已验证
DOI
高影响因子
RSC Advances
·
2016
·Vol. 6
·期 27
·22908-22916
·
IF 3.289
Jianwen Tian,Xiaohui He,Jingyin Liu,Xiaodan Deng,Defu Chen
Palladium(II) and copper(II) chloride complexes bearing bulky 9,10-dihydro-9,10-ethanoanthracene-11,12-diimine ligands were synthesized and sufficiently characterized by elemental and spectroscopic analysis along with X-ray diffraction analysis. The X-ray diffraction demonstrated that palladium(II) complexes (C1–C2) and copper(II) complexes (C3–C4) were four-coordinated. All these complexes displayed catalytic activities up to 105 gpolymer molMt−1 h−1 for norbornene vinyl-addition polymerization on treatment with excess methylaluminoxane (MAO). The parameters of the reaction conditions, the type of metals and steric effects of coordinative ligands had influences on the catalytic properties. C2 was selected as a catalyst precursor for the copolymerization of norbornene (NB) with 2-butyloxymethylene norbornene (BN), which exhibited catalytic activities up to 1.1 × 105 gpolymer molPd−1 h−1 and produced copolymers with relatively high molecular weights. The fraction of BN in the copolymer could reach up to 9.8–62.1% by controlling the monomer feed ratio range from 10–80%. The achieved vinyl-addition type poly(NB-co-BN) displayed high thermal stability and was soluble in common organic solvents, such as CHCl3 and THF.
研究领域:
高分子化学
·
配位化学
·
催化化学
·
有机金属化学
·
功能高分子材料
✓ 已验证
DOI
高影响因子
RSC Advances
·
2014
·Vol. 4
·期 78
·41398-41410
·
IF 3.708
Xiuhua Li,Jinxiong Tao,Guanghui Nie,Liuchan Wang,Liuhong Li,Shijun Liao
A series of cross-linked multiblock copoly(arylene ether sulfone) ionomer/nano-ZrO2 (CLQCPAES/nano-ZrO2) composite anion exchange membranes were prepared via block copolymerization, bromomethylation, ultrasonication blending, self-crosslinking, quaternization and alkalization. The structure, and the surface and cross section morphology of the CLQCPAES/nano-ZrO2 composite membranes were characterized by solubility tests, FT-IR, XRD and SEM analyses. The combination of the determined results revealed that the CLQCPAES/nano-ZrO2 composite membranes are a complex cross-linking networks of hydrophobic domains/hydrophilic domains/nano-ZrO2 with a clear zonal distribution of uniform nano-sized particles in the hydrophilic domains, when the nano-filler loading was below 7.5%. Basic performances of the CLQCPAES/nano-ZrO2 composite membranes were assessed to investigate their application in fuel cells in terms of the water uptake, swelling ratio, ion exchange capacity (IEC), hydroxide conductivity, thermal and mechanical properties, and alkaline stability. The modification of anion exchange membranes with multiblock ionomer structures, the use of a cross-linking technique and the introduction of nano-ZrO2 particles greatly enhanced the water uptake, hydroxide conductivity, mechanical properties and alkaline stability of the composite membranes. In particular, the CLQCPAES/7.5%ZrO2 membrane with an IEC value of 1.23 mmol g−1 exhibited the best comprehensive properties and constitutes a good potential candidate for an anion exchange membrane to be used in AEMFCs.
研究领域:
高分子材料科学
·
电化学
·
能源材料
·
膜科学与技术
·
燃料电池
·
纳米复合材料
·
功能高分子
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2014
·Vol. 132
·期 7
·
IF 1.64
Pan Dongdong,Tian Hengshui
Soluble and thermally stable polycarbonate polyurethane elastomers were synthesized through a solvent-free and nonisocyanate melt transesterification process. The conditions of this process were studied, and the optimum conditions were as follows: the catalyst dibutyltin oxide dosage was 0.125 wt %, the raw material molar ( n ) ratio of dimethyl 1,6-hexamethylene dicarbamate (HDC) to poly(carbonate macrodiol) (PCDL) was n (HDC)/ n (PCDL) = 1:0.99, the reactants were prepolymerized under 100°C for 1 h and then under 185°C and a high vacuum for 4 h. Three different PCDLs were selected to participate in the reaction under the conditions mentioned previously, and their structures were characterized by Fourier transform infrared spectroscopy and X-ray diffraction. The products obtained from this process were still stable under 280°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132 , 41377.
研究领域:
高分子化学
·
生物材料
·
聚合物科学
·
材料化学
·
医用高分子
✓ 已验证
DOI
高影响因子
Journal of Energy Chemistry
·
2023
·
IF 13.1
Yiran Sun,Pengfei Zhou,Siyu Liu,Zhongjun Zhao,Yihao Pan,Xiangyan Shen,Xiaozhong Wu,Jinping Zhao,Junying Weng,Jin Zhou
P2-Na 0.67 Ni 0.33 Mn 0.67 O 2 (NNMO) is promising cathode material for sodium-ion batteries (SIBs) due to its high specific capacity and fast Na + diffusion rate. Nonetheless, the irreversible P2-O2 phase transformation, Na + /vacancy ordering, and transition metal (TM) dissolution seriously damage its cycling stability and restrict its commercialization process. Herein, Na occupation manipulation and interface stabilization are proposed to strengthen the phase structure of NNMO by synergistic Zn/Ti co-doping and introducing lithium difluorophosp (LiPO 2 F 2 ) film-forming electrolyte additive . The Zn/Ti co-doping regulates the occupancy ratio of Na e /Na f at Na sites and disorganizes the Na + /vacancy ordering, resulting in a faster Na + diffusion kinetics and reversible P2-Z phase transition for P2-Na 0.67 Ni 0.28 Zn 0.05 Mn 0.62 Ti 0.05 O 2 (NNZMTO). Meanwhile, the LiPO 2 F 2 additive can form homogeneous and ultrathin cathode-electrolyte interphase (CEI) on NNZMTO surface, which can stabilize the NNZMTO-electrolyte interface to prevent TM dissolution, surface structure transformation, and micro-crack generation. Combination studies of in situ and ex situ characterizations and theoretical calculations were used to elucidate the storage mechanism of NNZMTO with LiPO 2 F 2 additive. As a result, the NNZMTO displays outstanding capacity retention of 94.44% after 500 cycles at 1C with 0.3 wt% LiPO 2 F 2 , excellent rate performance of 92.5 mA h g −1 at 8C with 0.1 wt% LiPO 2 F 2 , and remarkable full cell capability. This work highlights the important role of manipulating Na occupation and constructing protective film in the design of layered materials, which provides a promising direction for developing high-performance cathodes for SIBs.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
固态化学
·
电池技术
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2022
·
IF 9.794
Yuanyuan Li,Jun Cheng,Jianwei Li,Zhen Zeng,Yixuan Guo,Hongqiang Zhang,Hongbin Liu,Xiao Xu,Yiwei Rao,Deping Li,Lijie Ci
Sulfide solid state electrolytes capture much attention owing to their high conductivity and decent mechanical property. Nevertheless, the moisture instability and poor interfacial compatibility against lithium metal anode remain challenging and hinder the practical application. Herein, we report a novel indium (In) doping strategy based on the hard-soft-acid-base theory to tackle these issues. Optimized Li 7 P 2.9 S 10.9 In 0.1 electrolyte exhibits a high ionic conductivity of 4.1 × 10 −3 S cm −1 and achieves an enhanced interfacial compatibility. Importantly, as In partially replaces the phosphorus (P), the amount of released hydrogen sulfide can be significantly decreased and the air stability is improved. The all-solid-state battery assembled with the Li 7 P 2.9 S 10.9 In 0.1 electrolyte demonstrates a high discharge capacity and a good cycling stability under a high current density of 1.0 C. This work provides a practical and effective method to design sulfide-based solid-state electrolyte with high ionic conductivity and enhanced air stability for all-solid-state battery applications.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态离子学
·
电池技术
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2020
·Vol. 8
·期 46
·24579-24589
·
IF 11.301
Yongkang Han,Jinmei Xu,Wei Wang,Fu Long,Qunting Qu,Yan Wang,Honghe Zheng
Interfacial modification is one of the most important technologies to improve the overall electrochemical properties of Ni-rich cathodes. Herein, a novel strategy of in situ planting of an electrolyte film-forming additive on a single crystal NCM811 surface is proposed by consuming the residual lithium to develop a functional Al(Li)BOB nano-layer. Different from traditional physical coating, this approach cleverly consumed the undesirable residual lithium on the NCM811 surface. The in situ grown 30–50 nm Al(Li)BOB layer on the single crystal NCM811 cathode surface contributes to its much enhanced electrochemical performances. At a high operating voltage (charge voltage limit of 4.5 V vs. Li/Li+), the capacity retention is greatly increased from 57.0% to 83.5% after 295 cycles. Meanwhile, the incorporation of aluminum is effective in improving the thermal stability of the Ni-rich cathode. The novel interfacial strategy by in situ implanting of an electrolyte additive is of important significance for solving the critical interfacial issue for Ni-rich cathode materials.
研究领域:
材料科学
·
电化学
·
能源存储
·
锂离子电池
·
界面工程
·
纳米材料
·
固态化学
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Wan Su,Yufeng Zhang,Wenjuan Zhang,Shuting Xie,Xiaobo Sun,Jianqiang Meng
In this study, a nanofiltration (NF) polyamide hollow fiber thin film composite membrane with a low rejection and a high flux was prepared in consideration of the “trade-off” relation between salt rejection and permeate flux of the membrane. The membrane was able to retain the beneficial minerals in tap water while keeping the body healthy. The membrane prepared had a thinner active skin layer (<100 nm) than those of commercial membranes. A permeability of 30.07 L/m 2 /h and a rejection rate of 79.68% for 1,000 mg/L MgSO 4 at 0.2 MPa were obtained. In addiiton, Fe 3+ , Cu 2+ , and Pb 2+ were used to evaluate the heavy metal removal performance of the NF membrane. It was found that as the concentration of heavy metal ions increased to three times of the Standards for Drinking Water Quality (SDWQ) (GB5749-2006), and the rejections to all heavy metal ions were more than 76%. In addition, the NF membrane had a good long-term rejection stability for the heavy metal ions over a 12-month dynamic filtration experiment. The results showed that the newly prepared NF membrane has a good application prospect for domestic water purification.
研究领域:
环境科学
·
材料科学
·
膜技术
·
水处理
·
纳米技术
·
化学工程
·
公共卫生工程
✓ 已验证
DOI
高影响因子
Small
·
2023
·Vol. 19
·期 40
·2303227
·
IF 13.3
YuanZhe Wu,Quan Zong,Chaofeng Liu,Yanling Zhuang,Daiwen Tao,Jiangying Wang,Jingji Zhang,Qilong Zhang,Guozhong Cao
Vanadyl phosphate (VOPO 4 ·2H 2 O) has been regarded as one of the most promising cathode materials for aqueous Zn-ion batteries due to its distinct layered structure. However, VOPO 4 ·2H 2 O has not yet demonstrated the exceptional Zn ion storage performance owing to the structural deterioration during repeated charging/discharging process and poor intrinsic conductivity. In this work, 2D sodium vanadyl phosphate (NaVOPO 4 ·0.83H 2 O, denoted as NaVOP) is designed as a cathode material for Zn-ion batteries, in which sodium ions are preinserted into the interlayer, replacing part of water. Benefiting from the in situ surface oxidization, improved electronic conductivity, and increased hydrophobicity, the NaVOP electrode exhibits a high discharge capacity of 187 mAh g −1 at 0.1 A g −1 after activation, excellent rate capability and enhanced cycling performance with 85% capacity retention after 1500 cycles at 1 A g −1 . The energy storage mechanism of the NaVOP nanoflakes based on the rapid Zn 2+ and H + intercalation pseudocapacitance are investigated via multiple ex situ characterizations.
研究领域:
材料科学
·
电化学
·
能源存储
·
无机化学
·
纳米材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）