Surfaces and Interfaces
·
2025
·
IF 6.3
Kai Yang,Junhao Wang,Dian Yu,Pengqiuyue Pu,Hang Li,Zihao Chen,Yangyang Tang,Zhao Fang
As mineral resources are developed and exploited, the proportion of low-grade zinc ore increases. The concentrations of F - exceeding the optimal range may pose a risk to zinc hydrometallurgy . In the present research, Al 2 O 3 -ZnO microspheres (AZO) characterized by a substantial specific surface area were synthesized through a hydrothermal-roasting technique and applied in industrial zinc sulphate fluoride removal. The optimal adsorption conditions for AZO and the underlying adsorption mechanism were investigated. The results indicated that the adsorption at 12 g·L -1 dosage, original pH=5.32 of the solution and 323 K for 75 min, when the fluoride concentration was reduced to below 50 mg·L -1 , the fluoride removal percentage reached 73.32 %, and the adsorption capacity was 8.55 mg·g -1 . Kinetic studies revealed that AZO exhibited surface inhomogeneity, functioning as a heterogeneous adsorbent, with the fluoride adsorption process being predominantly chemical in nature. The isotherm model suggested that the removal process was characterized by homogeneous adsorption of a monomolecular layer, with a theoretical maximum adsorption capacity of AZO estimated at 9.479 mg·g -1 . FT-IR and XPS analyses demonstrated that the defluorination process occurs through ion exchange between F - and -OH, as well as the formation of Zn/Al-F complexes. Consequently, AZO present a novel approach for developing an effective adsorbent for defluorination in industrial ZnSO 4 solutions.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF PHYSICS D-APPLIED PHYSICS
·
2023
·Vol. 56
·期 29
·294003
·
IF 3.4
Y F Wang,B X Du,X X Kong,Fan Li,Xin Lin
Bisphenol A and F epoxy resins are often used as the primary insulation in power equipment. This paper investigates the influence of network structure on the dielectric properties of bisphenol A, bisphenol F epoxy resin and their blends. The results show that substituting isopropyl with methylene in epoxy resin enhances the molecular chain packing efficiency, thus limiting the polarization effect while reducing glass transition temperature (Tg). As the content of bisphenol F resin in the blends increases, the polarization loss of the blends continues to decrease, to even lower than that of bisphenol F resin. For the blend containing 20% bisphenol F resin, the Tg and AC breakdown strength at high temperatures are higher than that of bisphenol A resin. Furthermore, based on molecular dynamics simulation, the reason for the limited polarization effect of the blends is further discussed.
✓ 已验证
DOI
高影响因子
Functional Materials Letters
·
2024
·
IF 1.2
Zhuqing Sun,Yongxia Li,Haowen Bai,Shenghang Jin,Haibo Zhang,Guanying Cao
All inorganic lead halide cesium perovskite quantum dots (QDs) have attracted much attention due to their excellent luminescence properties, but further development is restricted by their stability and the existence of toxic element lead. In this paper, F/Mn-doped CsPb ( Br / Cl ) 3 QDs glass was prepared by melt quenching and heat treatment, with reduced Pb content effectively. The result shows that the spectrum of the QD glass is adjustable between 450 nm and 515.4 nm by changing the feeding ratio of Mn-Pb ion and heat treatment temperature. Moreover, the indraught of Mn 2 + effectively improves the PLQY of CsPb ( Br / Cl ) 3 QDs glass and serves as a red-emitting. The prepared composites not only maintain good fluorescence characteristics, but also greatly improve the stability of QDs. And successfully coupled with blue LED chips to synthesize WLED, Under 20 mA current, the color coordinate is (0.3446, 0.3389).
✓ 已验证
DOI
高影响因子
BIOTECHNOLOGY AND APPLIED BIOCHEMISTRY
·
2020
·Vol. 68
·期 6
·1192-1201
·
IF 1.638
Lingqiang Meng,Jianmin Dai,Shengzhong Rong,Hongmin Gao,Ze Zhang,Yingcong Zhang,Dong Chang,Hongzhi Pan
In our work, one-step electro-deposition method was adopted to produce polyaniline (PANI) and functional multiwalled carbon nanotubes (f-MWCNTs) films on glass carbon electrodes, and the modified electrodes were applied as an electrochemical sensor for determination of 10-hydroxycamptothecine (10-HCPT). The f-MWCNTs were handled by ultrasound processing in concentrated oxidizing acid solution, which can obtain a wonderful dissolution in water and attach new functional groups, such as –COOH and –OH. Then, aniline monomer could polymerize on the surface easily. The surface characterization was investigated using various techniques including scanning electron microscope, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction, and electro-catalytic properties were characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Under optimal conditions, the resulting of PANI/f-MWCNTs sensor showed a wide linear range (3 × 10 −9 to 7 × 10 −7 mol L −1 ) and a low detection limit (1 10 −9 mol L −1 ), which is attributing to its large special surface area and good conductivity. Moreover, the modified electrodes are convenient to fabricate, which can be used to detect 10-HCPT in urine samples successfully.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2021
·
IF 9.229
De Zhao,Zhihua Wu,Wei Zhang,Jian Yu,He Li,Wen Di,Yourong Duan
To date, ZnO array-based microfluidic fluorescence assays have been widely investigated and have exhibited excellent performance in the detection of cancer biomarkers. However, the requirements of highly sensitive detection necessitate further improvement of current Zn-based fluorescence detection devices. Here, a rhombus-like Zn(OH)F array-based microfluidic fluorescence detection device is proposed. Construction of Zn(OH)F arrays on the inner wall of a microchannel is carried out via a microfluidic chemical method. A substrate-induced growth strategy for Zn(OH)F arrays is proposed, and various micro/nanostructured Zn(OH)F arrays are successfully obtained. Zn(OH)F nanorod arrays with a high aspect ratio can be constructed on the columnar ZnO nanorod arrays, and the results indicate that the fluorescence enhancement factor (EF) of the Zn(OH)F arrays toward Cy3 is approximately 4-fold that of the ZnO nanorod arrays, which can be attributed to the higher excitation light absorption and evanescent electric field. In human epididymis-specific protein 4 (HE4) detection, the limit of detection (LOD) reaches 9.3 fM, and the dynamic linear range is 10 fM to 100 pM. It has been demonstrated that Zn(OH)F nanorod array-based microfluidic devices are excellent fluorescence assay platforms that also provide a new design and construction strategy for fluorescence enhancement substrates for the detection of biomarkers.
✓ 已验证
DOI
高影响因子
Science of Advanced Materials
·
2019
·Vol. 11
·期 3
·418-424
·
IF 1.158
Lv Yao,Huang Shifei,Zhao Yufeng
The N-B-F tridoping 3D hierarchical porous graphitized carbon network is produced by a one-step synthesis using chitosan as a precursor. The N-B-F tridoping 3D hierarchical porous graphitized carbon network is rich of nitrogen, boron and fluorine hetero atoms and exhibited relatively
high specific capacitance value of 316 F g–1 in 6 M KOH at a current density of 20.0 A g–1. As well as good cycling stability with capacitance retention of 100% over 10000 cycles, and good rate performance (90.3% capacity retention from 0.5 A g–1
to 20.0 A g–1). When used as supercapacitor electrode, the all carbon symmetric supercapacitor based on N-B-F tridoping 3D hierarchical porous graphitized carbon network delivers a high energy density of 23.87 Wh kg–1, outperforming the state-of-the-art carbon
material.
✓ 已验证
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2021
·
IF 3.764
Zhicai Zhang,Heng Yuan,Fugang Qi,Nie Zhao,Biao Zhang,Xiaoping Ouyang
A high-performance BN@F-SiC filler was prepared by depositing hydrophobic nano-SiC grafted by γ-aminopropyltriethoxysilane (KH550) and 1H,1H,2H,2H-trifluoro-noctyltriethoxysilane (FAS) on h-BN grafted by glycidoxy-propyltrimethoxysilane (KH560). A coating containing 1 wt % composite was prepared by dispersing the composite material in epoxy resin (EP), and dispersion, wear resistance, corrosion resistance, electrochemical analysis, and other tests were performed. Also, the influence of h-BN and SiC quality ratios on these properties was systematically studied. The results showed that the BN@F-SiC (2:1) composite material had the best dispersibility in EP. The water contact angle for the coating reached 118°, which indicated that the coating is hydrophobic. The friction coefficient for the BN@F-SiC (2:1)/EP coating was reduced by 89.68% compared with that for the coating without any filler. The potential dynamic polarization test and the salt spray test showed that BN@F-SiC had excellent corrosion inhibition performance. In addition, an EIS test showed that the impedance value for the BN@F-SiC (2:1)/EP coating exceeded 1010 Ω·cm2 at a frequency of 10–2 Hz (|Z|0.01Hz) after 400 h of soaking, which is nearly 103 times higher than that obtained for the EP coating without a filler. This research helps establish a foundation for future research investigating the development of wear-resistant hydrophobic and anticorrosive coatings.
✓ 已验证
DOI
高影响因子
Canadian Journal of Chemistry
·
2025
·
IF 1
Xin Guo,Pai Chen,Rui Wang,Ruijing Sun,Wei Jian,Yang Zhang,Yongsheng Bao,Shuai Wang
Most areas have long been affected by endemic fluorosis, which can lead to fluorosis bone disease and cardiovascular damage. The detection and treatment of fluoridated water has been of great concern. In this work, the sensors SP-1 and SP-2 were synthesized from naphthylamine and pyreneamine with carboxy-modified spiropyran via amidation reaction. The photoisomerization of spiropyran molecules under alternating ultraviolet/visible light irradiation resulted in changes in the conjugation system, which amplifies the combination between F− and the amide bonds of SP-1 and SP-2 molecules, enabling rapid and naked-eye detection of F−. Simultaneously, the impact of two distinct conjugated rings, pyridineamine and naphthaleneamine, on spiropyran detection of F− was investigated. Based on results from the UV spectrum, 1HNMR, and DFT theoretical calculation, it was determined that both sensor SP-1 and SP-2 can detect F− with a binding ratio of 1:1. The detection limits for sensor SP-1 are 0.978 µM for F−, and SP-2 are 0.173 µM for F−. The detection limit of SP-2, with a larger chromophore than SP-1, is lower and exhibits a more pronounced phenomenon. This study holds significant practical implications for rapid anion detection in aqueous environments, visual recognition without the need for specialized equipment, and energy conservation.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2018
·
IF 8.097
Peng Wei,Yanxiang Liu,Yarui Su,Ling Miao,Yangyang Huang,Yi Liu,Yuegang Qiu,Yuyu Li,Xiaoyu Zhang,Yue Xu,Xueping Sun,Chun Fang,Qing Li,Jiantao Han,Yunhui Huang
We are presenting a sol–gel method for building novel nanostructures made of nanosized F-doped Na1–2xTi2(PO4)3–xFx (NTP-Fx, x = 0, 0.02, 0.05, and 0.10) particles embedded in three-dimensional (3D) carbon matrices (NTP-Fx/C). This technique combines advantages of both zero-dimensional materials and 3D-carbon networks. Proper fluorine doping stabilizes the NTP structure and greatly enhances ion/electron transportation, leading to superhigh-rate electrochemical performance and ultralong cycle life. The composite electrode delivers high specific capacities of 121, 115, 112.2, 110.1, 107.7, 103.1, 85.8, and 62.5 mA h g–1 at 0.2, 0.5, 1, 2, 5, 10, 20, and 30 C, respectively. It retains an unbelievable ∼70% capacity after a thousand cycles at a rate as high as 10 C. Electroanalytical results reveal that fluorine doping significantly enhances Na+ diffusion kinetics. Meanwhile, density functional theory calculations demonstrate F-doped NTPs’ own outstanding electrochemical properties, which is due to the enhanced intrinsic ionic/electronic conductivity. The results show that anion doping is an efficient way to make high-performance NTP anodes for sodium-ion batteries.
✓ 已验证
DOI
高影响因子
FOOD AND CHEMICAL TOXICOLOGY
·
2014
·
IF 2.61
Lingchen Yang,Zhiyong Zhao,Yifeng Deng,Zhenlei Zhou,Jiafa Hou
The T-2 and HT-2 toxins, the main metabolites of Fusarium poae , induce toxicity in broilers and accumulate in tissues. Consequently, during the breeding process of broilers, diets are frequently supplemented with physical adsorbents to protect birds against the toxicity induced by mycotoxins. In the present research, T-2 and HT-2 were produced in maize inoculated with F. poae . Mont, the strongest adsorbent based on in vitro adsorption ratios, was added to the contaminated diet. One-day-old chickens were randomly and equally divided into the following four groups: control diet group, Mont supplemented diet group, contaminated diet group and detoxification diet group. The experiment lasted for 42 days. Compared to the control group, the contaminated group showed significant decrease in body weight, feed intake and TP ( P < 0.05), and marked increase in FCR, ALP, AST and ALT activity, T-2/HT-2 residues in the tissues and the relative expressions of apoptosis-related mRNAs ( P < 0.05). Mont supplementation provided protection for the treated broilers in terms of performance, blood biochemistry, hepatic function, T-2/HT-2 residue of tissues and apoptosis. Therefore, Mont may be suitable as a detoxification agent for T-2/HT-2 in feed for broilers.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2023
·Vol. 14
·期 1
·1-14
·
IF 16.6
Liu Di,Song Yanling,Chen Hui,You Yuchan,Zhu Luwen,Zhang Jucong,Xu Xinyi,Hu Jiahao,Huang Xiajie,Wu Xiaochuan,Xu Xiaoling,Jiang Saiping,Du Yongzhong
Poor renal distribution of antibody-based drugs is the key factor contributing to low treatment efficiency for renal diseases and side effects. Here, we prepare F(ab′) 2 fragmented vascular endothelial growth factor receptor 2 antibody (anti-VEGFR2 (F(ab′) 2 ) to block VEGFR2 overactivation in diabetic nephropathy (DN). We find that the anti-VEGFR2 F(ab′) 2 has a higher accumulation in DN male mice kidneys than the intact VEGFR2 antibody, and simultaneously preserves the binding ability to VEGFR2. Furthermore, we develop an antibody fragment drug conjugate, anti-VEGFR2 F(ab′) 2 -SS31, comprising the anti-VEGFR2 F(ab′) 2 fragment linked to the mitochondria-targeted antioxidant peptide SS31. We find that introduction of SS31 potentiates the efficacy of anti-VEGFR2 F(ab′) 2 . These findings provide proof of concept for the premise that antibody fragment drug conjugate improves renal distribution and merits drug validation in renal disease therapy.
✓ 已验证
DOI
PubMed
高影响因子
RSC Advances
·
2018
·Vol. 8
·期 11
·6053-6062
·
IF 2.936
Tian-Ying Luo,Xi He,Ji Zhang,Ping Chen,Yan-Hong Liu,Hai-Jiao Wang,Xiao-Qi Yu
Carbon dots (CDs) are photoluminescent nanoparticles with distinctive properties, having great potential in nano-biomaterial systems such as gene/drug delivery vectors and cell imaging agents. Fluorine-doped CD C-6F was prepared by a one-step ring-opening polymerization-dehydrative carbonization (RPDC) approach based on low molecular weight polyethyleneimine (PEI, 600 Da) and fluorinated diglycidyl ethers, while the non-fluorinated counterpart C-6H and the CD prepared from PEI 600 Da solely (C-600) were also prepared for comparison. TEM, FT-IR and XPS were performed to determine the compositions and surface states of the CDs. In vitro cell experiment results reveal that the CDs prepared from RPDC approach have much higher transfection efficiency and cellular uptake than PEI 600 contrasts in various cell lines. Compared to non-fluorinated C-6H, C-6F exhibited distinctly higher transfection efficiency, and up to 30 and 260 times higher efficiency than PEI 25 kDa could be achieved in the absence and presence of serum, respectively, indicating the advantage of F-doping. Besides, these CDs exhibit good cell imaging capability under single wavelength excitation, making the materials suitable for cellular tracking and transfection mechanism studies. These results demonstrate that fluorine-doping is an efficient approach to obtained CD gene vectors with high efficiency and serum tolerance.
✓ 已验证
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）