LANGMUIR
·
2025
·
IF 3.9
Yunhui Xia,Chengmei Huang,Jingsheng Wang,Guohui Cai,Mengjia Zhang,Jianghui Lin,Ling Li
The direct synthesis of dimethyl carbonate (DMC) from carbon dioxide (CO2) and methanol (CH3OH) represents one of the most attractive strategies in green chemistry, offering 100% atom economy for CO2 utilization. However, this reaction faces significant thermodynamic and kinetic challenges, limiting its practical application. To overcome these barriers, the development of highly efficient catalysts capable of effectively activating the CO2 is essential to achieve industrially viable DMC yields. Herein, a series of poly(ionic liquids) (PILs)@MOF-808 nanocomposites (including poly[AlDBU]Br@MOF-808, poly[AlDBN]Br@MOF-808, and poly[AlTMG]Br@MOF-808) were successfully synthesized via in situ polymerization. These composites integrate Lewis basic N sites, Lewis acidic Zr centers, and nucleophilic Br– within a MOF-808 framework. The nanocomposites were evaluated in a batch autoclave for the direct synthesis of DMC from CO2 and CH3OH. Among them, poly[AlDBU]Br@MOF-808 showed the highest DMC yield. Through systematic optimization of the poly[AlDBU]Br loading and reaction parameters (including temperature, CO2 pressure, and time), a maximum DMC yield of 2.52 mmol·g–1cat was achieved with poly[AlDBU]Br@MOF-808-0.4 at 120 °C under 3 MPa of CO2 for 5 h. Experimental studies and in situ DRIFTS confirmed the synergistic catalytic effect between MOF-808 and the PILs, highlighting their cooperative role in enhancing CO2 activation and DMC formation. The catalytic performance of poly[AlDBU]Br@MOF-808-0.4 is competitive compared to previously reported catalysts. The fundamental understanding of the synergistic effects between MOF-808 and PILs offers groundbreaking insights for CO2 capture and utilization strategies in direct DMC synthesis.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
IONICS
·
2026
·
IF 3.4
Wu Keying,Xie Wenda,Liu Xingjian,Chen Jing,Pu Haitao,Luo Bing
Separator design can improve electrolyte wetting, ion transport and dimensional stability in lithium metal cells with LiFePO 4 cathodes. Here, an Fe–Ti metal–organic framework (MOF) was prepared by a solvothermal route and incorporated into poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofiber membranes by electrospinning. The effects of filler loading were evaluated against pristine PVDF-HFP and a commercial Celgard separator. Among the investigated compositions, PVDF-HFP/MOF-10 exhibited an electrolyte contact angle of 18°, an ionic conductivity of 1.7 × 10⁻ 3 S cm⁻ 1 at 30 °C, and an apparent Li⁺ transference number of 0.56 under the Bruce–Vincent measurement protocol. The composite also showed improved thermal dimensional stability. Li‖Li cells operated for over 500 h at 1 mA cm⁻ 2 and 1 mAh cm⁻ 2 , while LiFePO 4 ‖Li cells retained 92.3% of their initial discharge capacity after 500 cycles at 1 C. These observations support the use of the composite separator for improving performance under the tested conditions. Adsorption calculations provide a possible molecular explanation for electrolyte affinity, but do not establish ion desolvation, selective anion immobilization or a unique bimetallic synergy in the operating electrolyte. The contribution is the integration and loading optimization of an Fe–Ti MOF within a porous PVDF-HFP separator, with the microscopic transport mechanism remaining to be resolved.
✓ 已验证
DOI
高影响因子
LANGMUIR
·
2025
·
IF 3.9
Yanrui Wang,Ting Yu,Qing Xue,Le Chen,Yue Chen,Zhonghua Sun,Junfeng Qian,Chang Guo,Vladimir Yu. Guskov,Zhi-Hui Zhang
In this study, a Zn-based MOF was synthesized via a solvothermal method, and a series of AG/Zn-MOF-X composite aerogels were subsequently engineered through the controlled incorporation of agar. Comprehensive evaluation revealed that the AG/Zn-MOF-0.8 composite achieved remarkable removal efficiencies of 65, 61, and 100% for Cr2O72–, CrO42–, and MnO4–, respectively, outperforming pristine Zn-MOF by 14, 3, and 1%. An analysis of the kinetics and isotherms provided insights into the adsorption mechanisms. Notably, under photocatalytic conditions, the composite exhibited superior degradation with removal rates of 79, 86, and 100% for the respective oxyanions. These findings highlight that tailored MOF modifications can significantly boost both adsorption and photocatalytic performance, offering new possibilities for advanced water purification technologies.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FUEL
·
2025
·
IF 7.5
Chi Li,JiXiang Guo,Li Wang,PengCheng Xue,WenLong Zhang,KunPeng Li
Heavy oil in-situ catalytic technology faces challenges like complex reservoirs, harsh environments, and high viscosity. Developing efficient in-situ catalysts is a key research focus. This study synthesized a Fe/Ce bimetallic organic framework (Fe/Ce-MOF) that addresses critical issues in heavy oil recovery. Under mild conditions at 140℃ with 0.5 wt% catalyst and 2 wt% hydrogen donor for 24 h, Fe/Ce-MOF achieved a 90.15 % reduction in viscosity and a 16.51 % decrease in asphaltene content. The characterization analysis and simulation results collectively reveal that the bimetallic MOF has a synergistic effect. On the one hand, the Fe 3+ /Fe 2+ redox cycle promotes the cracking of large molecules into smaller ones. On the other hand, the Ce 4+ /Ce 3+ redox cycle facilitates the formation of oxygen vacancies (O v ). Under the combined effect of the dynamic redox cycles of Fe 3+ /Fe 2+ and Ce 4+ /Ce 3+ , the electron transfer efficiency of the catalyst is significantly enhanced, increasing the rate of heavy oil pyrolysis and hydrogenation. The coexistence of Fe and Ce modifies the charge distribution in heavy oil MOF, enhancing Lewis acidity and promoting interaction with heteroatoms. Additionally, the coexistence of mesoporous and macropores in the bimetallic framework not only facilitated mass transfer and fully utilized the catalytic activity of active sites but also effectively resolves the issue of traditional microporous MOFs are prone to being blocked by larger asphaltene molecules, thereby improving their operational stability. This study proposes a novel strategy for the design and development of in-situ catalytic viscosity reduction catalysts for heavy oil, highlighting the high efficiency, excellent stability, and environmental compatibility of bimetallic MOF in low-temperature catalytic pyrolysis, and demonstrating their significant potential for practical applications.
✓ 已验证
产品关联
DOI
高影响因子
FUEL
·
2025
·
IF 7.5
Asmat Ullah,Gang Dong,Yasir Javed,Anosha Anwer,Dongsheng Geng
The Cu-based catalyst used for electrochemical CO 2 reduction reaction (CO 2 RR) is a capable approach to reducing greenhouse carbon emissions and producing high value-added multi-carbon (C2 + ) products. Unfortunately, the selectivity of the (C2 + ) products is still quite low. Therefore, it is imperative to develop persuasive electrocatalysts to facilitate the conversion of carbon dioxide into valuable chemical products. Here, we design a CuO Nanosheets catalyst with the phase composition of silver (Ag) and Ag metal–organic framework (Ag-MOF) by using the hydrothermal approach. A maximum ethylene faradaic efficiency (FE) of Ag-MOF/CuO NS is achieved as 45.72 % at −1.1 V (vs RHE), while those CuO NS and Ag/CuO NS show 31 % and 14.24 % respectively. Interestingly, the restructured porous nature of Ag-MOF doped CuO NS electrocatalyst is equipped with a high surface area with strong adsorption capacity of CO 2 and increases the oxygen vacancies abundance with high active sites for selective electrocatalysis activity based on as produced Ag-MOF on CuO surface. This indicates that, in heterostructured catalysts, the coordination between CuO and free carboxyl groups considerably can enhance the dimerization of *CO intermediates and provide a strong coordination environment to the Cu valence state with MOF for the selective electrocatalytic CO 2 reduction. Thereby, the reaction pathway is shifted from two electrons to a multi-electron by constructing the oxygen vacancies for the production of multi-carbon products.
✓ 已验证
产品关联
DOI
高影响因子
Materials Science and Engineering B-Advanced Functional Solid-State Materials
·
2025
·
IF 4.6
Haoyue Deng,Tiehu Li,Hao Li,Alei Dang,Yongkang Han
In this study, a composite material composed of Mg-MOF-74 and graphene oxide (GO) was synthesized to overcome MOFs’ limitations in CO 2 capture. At 273 K/101 kPa, the Mg-MOF-74 composite containing 6 wt% GO achieved 3.46 mmol/g CO 2 uptake and 114.4 CO 2 /N 2 selectivity, demonstrating 25.8 % and 29.3 % enhancements compared with pristine Mg-MOF-74. This enhancement is due to the optimization of CO 2 adsorption by the new pores formed at the interface and the strong affinity of GO functional groups for CO 2 molecules. Furthermore, due to the excellent properties of GO and its strong interaction with Mg-MOF-74, the composites show notable improvements in thermal, adsorption–desorption cycling, and moisture stability. Notably, the Mg-MOF-74 composite containing 6 wt% urea-modified GO exhibits optimal CO 2 adsorption/stability. This is not only due to the synergy between GO and Mg-MOF-74, but also because the amine groups and polar C O bonds in urea can boost adsorption/separation and enhance stability through amine-Mg 2+ coordination. These findings highlight Mg-MOF-74@GO composites as promising candidates for industrial CO 2 capture.
✓ 已验证
产品关联
DOI
高影响因子
COMPOSITES PART B-ENGINEERING
·
2025
·
IF 14.2
Yue Yin,Shengkai Liu,Xianyan Wu,Dong Liu,Amna Siddique,Muhammad Umair,Chunying Min,Xinke Zhou,Lei Chen,Chuanbin Yu,Zhiwei Xu
Metal-organic frameworks (MOFs) were strategically integrated into the interfacial region of carbon fiber reinforced polymer (CFRP) composites to investigate their mitigation effects on γ-ray irradiation-induced microstructural degradation. Systematic irradiation experiments were conducted at doses of 0, 250, 500 and 1000 kGy under ambient conditions. Scanning electron microscopy (SEM) results demonstrate that significant debonding and cracking of interfaces exposed to air media at irradiation doses of 500–1000 kGy, concomitant with an increase in oxygen content in the interfacial region is revealed by Energy Dispersive Spectroscopy (EDS). Oxygen permeation along the cracked interfaces into the CFRP interior, driven by irradiation, leading to an increase in the modulus and thickness of the “internal interface” as characterised by nanoindentation tests. In contrast, the MOF-modified composites effectively mitigated interfacial cracking, reducing the expansion of the interfacial layer thickness due to oxygen diffusion from 50 % (pristine) to 33 % (MOF-modified). Nanoscale infrared spectroscopy (nano-IR) demonstrated the MOF modification reduced the radiation-induced carbonyl and amide groups in the near-interface region, confirming suppressed oxidative degradation. Finally, three-point bending tests validated the macroscopic relevance, showing that MOF modification reduced the flexural strength loss from 12.3 % (unmodified) to 7.5 % after 1000 kGy irradiation. This work provides microscopic scale insights into interfacial radiation damage mechanisms and establishes a MOF-based interfacial engineering strategy to simultaneously block oxidative pathways and neutralize radiation species, advancing the design of radiation-resistant CFRPs for extreme environments.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2025
·
IF 6.9
Xiaoxin Wu,Si Chen,Huasen Shen,Yunan Tian,Guoning Wu,Tingting Ma,Mengjun Li,Yuyu Li,Zhaohuai Li
Separators constitute vital components in high-energy-density lithium metal batteries (LMBs), yet their propensity to fail under lithium (Li) dendrite growth remains a critical limitation. In this work, we report a commercial Celgard separator engineered with pearl-like nanospheres (Celgard@PNS) to enable electrochemically stable and dendrite-free lithium metal anodes (LMAs). The PNS-functionalized layer in the Celgard@PNS ensures rapid and homogeneous Li ion flux, which stabilizes LMAs and effectively mitigates dendritic Li deposition. Moreover, the PNS modification fosters the development of a robust solid-electrolyte interphase (SEI) layer. The Celgard@PNS-based Li||Cu half-cell exhibits stable Coulombic efficiency for 110 cycles, and the corresponding Li||Li symmetric cell sustains long cycling stability (>900 h) at a high current density of 10 mA cm −2 with an areal capacity of 1 mAh cm −2 . Impressively, when paired with a high-mass-loading NCM811 cathode (22.5 mg cm −2 ), the Li||NCM811 full cell retains 81.4 % of its initial capacity after 140 cycles at 0.5 C. These results underscore the potential of the Celgard@PNS separator for practical implementation in high-capacity LMBs.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF DRUG DELIVERY SCIENCE AND TECHNOLOGY
·
2025
·
IF 4.9
Ahmed M. Omer,Eman M. Abd El-Monaem,Heba S. Hassan,Mahmoud A. Elmeligy,Angela Kleinová,Abdelazeem S. Eltaweil,Abolfazl Heydari
pH-sensitive carriers have emerged as an optimal choice for the oral administration of anticancer drugs, exhibiting the desired release performance. This study aims to develop biocomposite beads for the sustained release of the anticancer drug 5-fluorouracil (5-FU). Here, 5-FU was encapsulated within a ZIF-8 metal-organic framework (MOF), which was subsequently impregnated into amino-chitosan beads. The resulting Am-CS@ZIF-8 biocomposite beads were characterized for their chemical structure, surface morphology, elemental composition, crystallinity, surface charges, and mechanical properties utilizing Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), zeta potential analysis, and a texture analyzer, respectively. The developed beads exhibited a textured surface, denser composition, and a positively charged surface with a maximum zeta potential of +12.4 at pH 7.4. In comparison to Am-CS beads, the Am-CS@ZIF-8 biocomposite beads demonstrated superior mechanical properties, achieving a maximum stress value of 5.668 MPa compared to the 1.874 MPa recorded for pure Am-CS beads. pH sensitivity was assessed through the investigation of water uptake behavior at pH 1.2 and pH 7.4. The Am-CS@ZIF-8 biocomposite beads demonstrated a high encapsulation efficiency of approximately 81.6 % for 5-FU. They exhibited pH-responsive release behavior, with only 17 % of the drug released at pH 1.2 after 2 h and a sustained release of 52 % at pH 7.4 over 24 h. The release mechanism was predominantly governed by Fickian diffusion, as closely fitted by the Peppas-Sahlin kinetic model. The formulated carrier confirmed its biodegradability under enzymatic physiological conditions, suggesting its potential applicability as an effective system for the oral delivery of anticancer drugs.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Yaping Zhang,Yanan Zhao,Yixin Qi,Yanyan Lin,Yuhang Cheng,Mengmeng Sun,Lei Wang
Photogenerated holes have emerged as critical mediators for activating peroxymonosulfate (PMS) in the coupled photocatalytic PMS activation system, enabling novel dual-channel activation pathway. A tandem system based on Fe-MOF@BiVO 4 (Vis/PMS/Fe-MOF@BVO) with spatially separated active sites was constructed to form a dual-channel activation mechanism. The BiVO 4 (010) face provides the active sites for photogenerated electrons to drive the Fe 3+ /Fe 2+ cycle and activate PMS, while the BiVO 4 (110) face serves as the active sites for photogenerated holes to activate PMS. Consequently, the Vis/PMS/Fe-MOF@BVO system achieved complete degradation of 10 mg/L BPA within 6 min, with a degradation rate constant (K obs ) of 0.74 min −1 . It also demonstrated high removal efficiency for various organic pollutants with excellent immunity to interference and reusability. This work provides a new insight into the coordinative mechanism for coupled photocatalysis and PMS activation system.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ELECTROCHIMICA ACTA
·
2025
·
IF 5.6
Qianxilong Wang,Jiakuo Chen,Jiansheng Wang,Xiongfeng Zeng,Ruimin Wang,Yingna Zhao
In this paper, TiO 2 nanotube arrays with gap characteristics were designed and fabricated. Moreover, by adjusting the ratio of metal ions to ligands (1:20), a fully coated Co-MOF/TiO 2 composite photoanode was obtained; Secondly, tests such as XPS and EPR were adopted and combined with theoretical calculations to verify the construction of Type II heterojunctions, which promoted the separation of photogenerated electron-hole pairs and thereby enhanced the cathodic protection effect of the composite photoanode. Finally, to promote green and environmentally friendly anti-corrosion materials, an in-depth study was conducted on the anti-corrosion and anti-pitting effects of composite photoanodes on 304SS with different application areas (1cm 2 ,25cm 2 ,100cm 2 ).
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2021
·
IF 5.316
Lin Cheng,Min Xie,Yitong Sun,Hong Liu
Constructing Z-scheme heterojunction is considered to be a promising strategy to isolate photogenerated carriers and boost the activity of the photocatalysts . Here in, a novel Z-scheme Bi 2 WO 6 /Ni-MOF heterojunction with intimate interface was constructed via wrapping flowerlike Bi 2 WO 6 on 2D Ni-MOF sheets. The resultant Bi 2 WO 6 /Ni-MOF heterojunction displayed superior photocatalytic performance with respect to methylene blue degradation under visible light illumination. When the content of Ni-MOF was 20 wt%, the Bi 2 WO 6 /Ni-MOF heterojunction achieved the highest activity, which was 24.0 and 6.4 folds that of the pristine Ni-MOF and Bi 2 WO 6 , respectively. The superior degradation performance was caused by the formation of a direct Z-scheme heterostructure between Ni-MOF and Bi 2 WO 6 , which boosted the separation of photoinduced carriers. The principal active species and possible photocatalytic mechanism were also explored. This study provides a pathway to design and fabricate efficient Z-scheme photocatalysts for environmental remediation.
✓ 已验证
DOI
高影响因子