JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2024
·Vol. 35
·期 18
·1251
·
IF 2.8
Zheng Jinjie,Shen Honglie,Li Yufang,Li Hechao,Yue Zhen
Novel efficient visible and near-infrared emitting phosphors NaY(MoO 4 ) 2 (NYM):Ln 3+ (Ln = Ce and Yb) were proposed in this work. The crystal structure, lattice vibration characteristics, morphology, and luminescent properties of NaY(MoO 4 ) 2 phosphors were described. Sensitization of Ln 3+ from the host with various doping concentrations was investigated. The yellow-green emission was achieved in Ce 3+ single-doped NYM phosphors at UV ultraviolet excitation sensitized by the MoO 4 2− group. Under UV excitation, characteristic emissions of Ce 3+ at 400–700 nm and Yb 3+ at 1000 nm of NYM:Ce,Yb were observed, enabling the spectral down-conversion applications. With the increasing concentration of Yb 3+ , the emission intensity as well as the lifetime of Ce 3+ decreased, confirming the energy transfer from Ce 3+ ions to Yb 3+ ions. And the energy transfer coefficient was 27% for NYM:0.01Ce,0.10Yb phosphor. These results indicate that the as-prepared phosphors have potential applications in optical and photonic devices.
研究领域:
材料科学
·
光学材料
·
发光学
·
无机化学
·
光子学
✓ 已验证
DOI
高影响因子
Laser & Photonics Reviews
·
2024
·Vol. 18
·期 11
·2400447
·
IF 9.8
Fangyi Zhao,Yuhe Shao,Quanlin Liu,Jiasong Zhong
Near-infrared (NIR) phosphor-converted light-emitting diode (pc-LED) light sources in the second NIR window (NIR-II, 1000–1700 nm) have sparked great interest for their emerging applications in non-destructive detection and medical diagnostics fields. However, the development of efficient NIR-II phosphors that can be excited by commercial blue LED chips remains a significant challenge, and thus impeding the applications of NIR pc-LED. Herein, a blue-light-excitable broadband NIR-II luminescence of Ni 2+ is achieved upon incorporating Cr 3+ and Ni 2+ into the Ca 3 Ga 2 Ge 3 O 12 (CGGO) host simultaneously. Through the energy transfer from Cr 3+ to Ni 2+ , CGGO:Cr 3+ ,Ni 2+ phosphor presents the improved NIR-II emission peaking at 1470 nm under 460 nm blue light excitation. The internal/external quantum efficiency values are significantly improved from 13.8%/3.3% to 24.6%/13.3% along with the enhanced luminescence thermal stability. Finally, a NIR pc-LED is fabricated by combining CGGO:Cr 3+ ,Ni 2+ phosphor with 450 nm blue chip, and its potential applications in non-destructive examination and biomedical imaging fields have been demonstrated. The strategy of Cr 3+ and Ni 2+ co-doping solves the problem that Ni 2+ luminescence cannot be effectively excited by blue light and provides the design insights to exploit more ultra-broadband NIR pc-LEDs based on blue LED chips.
研究领域:
材料科学
·
生物医学工程
·
光学成像
·
非侵入性检测
·
分子影像学
✓ 已验证
DOI
高影响因子
Small
·
2019
·Vol. 15
·期 10
·1804546
·
IF 10.856
Jing Yang,Donghua Guo,Shulin Zhao,Yue Lin,Rui Yang,Dongdong Xu,Naien Shi,Xiaoshu Zhang,Lingzhi Lu,Ya-Qian Lan,Jianchun Bao,Min Han
As one class of important functional materials, transition metal phosphides (TMPs) nanostructures show promising applications in catalysis and energy storage fields. Although great progress has been achieved, phase-controlled synthesis of cobalt phosphides nanocrystals or related nanohybrids remains a challenge, and their use in overall water splitting (OWS) is not systematically studied. Herein, three kinds of cobalt phosphides nanocrystals encapsulated by P-doped carbon (PC) and married with P-doped graphene (PG) nanohybrids, including CoP@PC/PG, CoP-Co 2 P@PC/PG, and Co 2 P@PC/PG, are obtained through controllable thermal conversion of presynthesized supramolecular gels that contain cobalt salt, phytic acid, and graphene oxides at proper temperature under Ar/H 2 atmosphere. Among them, the mixed-phase CoP-Co 2 P@PC/PG nanohybrids manifest high electrocatalytic activity toward both hydrogen and oxygen evolution in alkaline media. Remarkably, using them as bifunctional catalysts, the fabricated CoP-Co 2 P@PC/PG || CoP-Co 2 P@PC/PG electrolyzer only needs a cell voltage of 1.567 V for driving OWS to reach the current density at 10 mA cm −2 , superior to their pure-phase counterparts and recently reported bifunctional catalysts based devices. Also, such a CoP-Co 2 P@PC/PG || CoP-Co 2 P@PC/PG device exhibits outstanding stability for OWS. This work may shed some light on optimizing TMPs nanostructures based on phase engineering, and promote their applications in OWS or other renewable energy options.
研究领域:
材料科学
·
电催化
·
能源化学
·
纳米材料
·
可再生能源
✓ 已验证
DOI
高影响因子
RSC Advances
·
2021
·Vol. 11
·期 16
·9450-9458
·
IF 3.361
Rui Zhang,Zheng Wang,Lin Zhu,Weixin Lv,Wei Wang
For the electrochemical reduction of oxygen the development of heteroatom-doped carbon-based transition metal catalysts has become a recognized strategy to replace traditional noble metal catalysts. In this work a catalyst consisting of CoFe nanoparticles encapsulated in N-doped carbon-based materials (NC) supported by carbon nanotubes (CNTs), i.e. Fe3Co1@NC/CNTs, was modified via treatment with a phosphate salt to synthesize a P-Fe3Co1@NC/CNTs catalyst. The P-Fe3Co1@NC/CNTs exhibits with 5.29 mA cm−2 an enhanced current density which is comparable to a Pt/C catalyst. In addition, a stability and methanol resistance better than the Pt/C catalyst were observed which is ascribed to the carbon encapsulation and the synergies between the two transition metals. Finally, the reaction mechanism of P-doping was studied and discussed. These results provide possible directions for carbon-based catalysts and doping with heteroatoms for the improvement of catalytic activity. Moreover, the zinc–air battery assembled with P-Fe3Co1@NC/CNTs as the air-cathode exhibited a high-power density of 73 mW cm−2, which is comparable to that of Pt/C (71 mW cm−2) and a specific capacity of 763 mA h g−1. The prepared catalyst could potentially serve to take the place of precious metal catalysts in rechargeable Zn–air batteries.
研究领域:
电催化
·
材料化学
·
能源化学
·
纳米材料
·
电化学能源存储
·
燃料电池
·
金属-空气电池
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2017
·Vol. 28
·期 16
·11563-11568
·
IF 2.019
Sun Xinjie,Tong Hua,Yuan Xiao,Liu Cui,Yuan Shuanglong,Chen Guorong,Yang Yunxia
Thermal boron diffusion, which forms highly doped and shallow p-emitters on phosphor-doped silicon wafers, is one of the primary processes in commercial-scale production of n-type cells. Here, we report on the use of nontoxic and nonvolatile borosiloxane sols as the spin-on boron source. In comparison to the tribromide (BBr 3 ) boron diffusion that is applied in the production of most commercial n-type cells, borosiloxane boron diffusion may have potential advantages in terms of cost, safety, operability, etc. The borosiloxane sols studied here were formed from a cross-linking reaction between boron acid and a mixture of two types of silicon alkoxides, methyltriethoxysilane (MTEOS) and dimethyldiethoxysilane (DMDEOS). The MTEOS/DMDEOS ratio was found to be the key factor determining the synthetic period, net structure, thermal transformation property, and coating behavior of the borosiloxane sols. In combination with the spin-coating method, the performance of borosiloxane boron diffusion into phosphor-doped silicon wafers (1–3 Ω·cm) was systematically investigated by varying the borosiloxane composition (boron/silicon or MTEOS/DMDEOS ratio) and the diffusion process parameters (temperature, ambience, and period of individual sub-steps), and by relating them to the resulting sheet resistance and boron doping profile. The results show that under the diffusion conditions in conventional cell production lines, the formed p-emitters can have variable sheet resistance in the range of 35–582 Ω/□ and boron doping depth of 100–300 nm.
研究领域:
材料科学
·
半导体物理
·
光伏技术
·
表面工程
·
纳米材料
·
化学气相沉积
·
微电子学
✓ 已验证
DOI
高影响因子
CARBON
·
2013
·
IF 5.868
Xiuqing Meng,Sefaattin Tongay,Jun Kang,Zhanghui Chen,Fengmin Wu,Shu-Shen Li,Jian-Bai Xia,Jingbo Li,Junqiao Wu
ZnMg and NbCl 5 were intercalated in graphite and the presence of such molecules between the graphene sheets results in n- and p-type doping, respectively. The doping effect is confirmed by Hall and Raman measurements and the intercalation process is monitored by scanning tunneling microscopy . After intercalation the carrier concentration increase almost an order of magnitude and reaches values as high as 10 19 and 10 18 cm −3 for p- and n-type doping, respectively. For higher intercalation times, the intercalated graphite turns back to be as ordered as pristine one as evidenced by the reduction in the D peak in Raman measurements. Intercalation compounds show remarkable stability allowing us to permanently tune the physical properties of few-layer graphite. Our study has provided a new route to produce stable and functional graphite intercalation compounds and the results can be applied to other graphitic structures such as few-layer graphene on SiC.
研究领域:
凝聚态物理
·
材料科学
·
纳米科技
·
表面科学
·
半导体物理
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2018
·
IF 2.732
Qinghua Yang,Benxue Jiang,Shuilin Chen,Yiguang Jiang,Pande Zhang,Jun Wang,Shiqing Xu,Long Zhang
Al 2 O 3 : Er 3+ /Yb 3+ transparent ceramics codoped with Zn 2+ ions with intense upconversion and near infrared emission were prepared by conventional solid-state reaction and vacuum and hot isostatic pressing sintering. The effects of Zn 2+ incorporation to the structure, transparent, upconversion and NIR luminescence were discussed in detail. The as prepared Al 2 O 3 ceramics exhibited a total transmittance of ~ 75% in infrared regions (800–3300 nm) and ~ 50% in visible regions (500–800 nm). Under the excitation of a 980 nm laser diode , the as prepared Al 2 O 3 ceramics displayed two tense upconversion emission peaks of a green one centered at 550 nm and a red one centered at 660 nm and a tense near infrared emission peak centered at 1.532 µm, characteristic of Er 3+ emission. Compared with Er 3+ /Yb 3+ doped only, Zn 2+ codoped Al 2 O 3 :Er 3+ /Yb 3+ transparent ceramics showed higher upconversion and near infrared emission of ~ 11 times and ~ 4 times, respectively. The enhancement mechanism due to incorporation of Zn 2+ ions was also discussed in detail.
研究领域:
材料科学
·
光学材料
·
无机非金属材料
·
发光材料
·
陶瓷工程
✓ 已验证
DOI
高影响因子
Materials Today Chemistry
·
2022
·
IF 7.613
S. Wu,Y. Fu,Q. Liu,P. Xiong,D. Wang,G. Zhang,S. Yuan,Y. Chen
Developing highly efficient cyan-emitting fluorescent materials is essential to bridge the cyan gap in phosphor-converted white light-emitting diodes for full-spectrum white illumination. Here, a Bi-doped cyan phosphor has been reported to solve this gap. The phase purity, photoluminescence emission/excitation spectra, concentration quenching, lifetime decay curves, and temperature-dependent photoluminescence emission spectra were systematically investigated. SrLaGaO 4 :Bi 3+ exhibits a broad excitation band (250–400 nm), which matches with the emission of a commercial near-ultraviolet light-emitting diode chip. The cyan light peaked at 475 nm is observed, which is attributed to the 3 P 1 → 1 S 0 transition of Bi 3+ . The thermal quenching experiment was performed, and the activation energy was calculated as 0.36 eV. Finally, full-spectrum white light-emitting diode devices were fabricated using SrLaGaO 4 :Bi 3+ phosphors, commercial blue BaMgAl 10 O 17 :Eu 2+ phosphor, green (Ba, Sr) 2 SiO 4 :Eu 2+ phosphor, and red CaAlSiN 3 :Eu 2+ phosphor, which displayed an International Commission on an illumination coordinate of (0.3732, 0.3850), a correlated color temperature of 4290 K, and a color rendering index of 93.2 at a drive current of 20 mA. This result indicates that SrLaGaO 4 :Bi 3+ plays an essential role in bridging the cyan gap, providing new inspiration for applying cyan-emitting phosphors in full-spectrum white lighting.
研究领域:
材料科学
·
光学工程
·
固态照明
·
发光材料
·
无机化学
✓ 已验证
DOI
高影响因子
International Journal of Electrochemical Science
·
2023
·Vol. 15
·期 3
·2528-2538
·
IF 1.5
Wenhui Geng,Mengmeng Zheng,Dan Chen,Xianwen Wang,Zekai Zhang,Yishan Lin,Dongqin Cai,Huiqin Li,Guobo Huang,Yanxian Jin Yu,Binbin Yus
Palladium catalyst (Pd) are made attention to application in alcohol fuel cells due to unique performance, as well as the resource abundance and low cost, but the catalyst performance and stability of the catalysts are still not satisfied. In this article, the novel PdFe/B-N-G catalysts with the double element alloying and dual-doping for ethanol electro-oxidation are successfully prepared and determined by XRD, TEM and XPS. TEM results reveal a relatively uniform and high dispersion of Pd particles is observed on PdFe/B-N-G catalyst. The XPS analysis indicates that Pd(0) contents of the PdFe/B-N-G catalyst are increased on account of the B, N-doping effect. Being explored as the catalyst to the ethanol oxidation reactions, the PdFe/B-N-G catalysts exhibit the better electrocatalytic activity with higher current densities and catalyst stability compared to those of PdFe/G and Pd/B-N-G, which can be attributed to the synergistic effect of the enhanced PdFe alloying and the B, N-doping, that can produce more activity sites dispersing on the surface of graphene. Thus, the novel PdFe/B-N-G catalysts can be the potential alternate in alcohol fuel cells.
研究领域:
电化学
·
纳米催化
·
能源材料
·
燃料电池
·
表面科学
✓ 已验证
DOI
高影响因子
CATALYSIS COMMUNICATIONS
·
2015
·
IF 3.699
Feng Ding,Sizhao Zhang,Xuegang Luo,Xiaoyan Lin
A novel S/BiOCl thermocatalyst in response to heat excitation was successfully synthesized by a one-step method and then added into polymeric matrix to give corresponding films. The results obtained show that the surfaces of as-prepared films with S/BiOCl were truly degraded via thermocatalytic reactions at ambient conditions. The average molecular weights of experimental films have fallen dramatically, comparing to the comparisons. In addition, the changes of chemical groups were simultaneously observed in the process. Thus this thermocatalytic process maybe a very fascinating route to come true the degradation of polymeric films with lower temperature triggered.
研究领域:
材料科学
·
高分子化学
·
环境功能材料
·
催化化学
·
纳米材料
✓ 已验证
DOI
高影响因子
RSC Advances
·
2012
·Vol. 2
·期 12
·5403-5410
·
IF 0
Qinghua Liang,Yao Shi,Wangjing Ma,Zhi Li,Xinmin Yang
Uniform square-like BaFBr:Eu2+ microplates were successfully fabricated via a simple water/oil emulsion method. Various characterization techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, Scanning electron microscopy (SEM) and Transition electron microscopy (TEM) were employed to examine the phase, size, morphology, and structure of the products. It was found that the morphology and size of products were strongly dependent on the reaction parameters, such as the ratio of reactants, the reaction time and the reaction temperature. The length and thickness of these square-like BaFBr:Eu2+ microplates can be tuned by adjusting the reaction time and temperature. Well-dispersed cuboctahedron and corner cut cuboid-like BaFBr:Eu2+ particles were produced when the reaction temperature was increased above 60 °C. A possible formation mechanism of the products was discussed based on the time and temperature-dependent experimental results. The optical properties were characterized by photoluminescence (PL) spectroscopy as well as kinetic decay. Eu2+-doped dependent luminescent intensity was investigated in detail. The prepared BaFBr:Eu2+ phosphors are considered promising materials for fluorescent applications.
研究领域:
材料科学
·
无机化学
·
纳米技术
·
光学材料
·
功能材料
✓ 已验证
DOI
JOURNAL OF MATERIALS SCIENCE
·
2020
·Vol. 55
·期 20
·8642-8650
·
IF 3.553
Chen Shaoping,Xu Libin,Li Rong,Fan Wenhao,Chen Yanzuo,An Decheng,Wang Wenxian,Wu Yucheng
Energy filtering effect is helpful to decouple Seebeck coefficient and electric conductivity, and dopant is helpful for improving conductivity; in this work, synergetic function of both is supposed to enhance zT values of tellurium.
In bulk Te and Sb 0.003 Te 0.997 , the Ni/Te heterojunction was built by electroless plating combined with spark plasma sintering. The Ni/Te interface barrier successfully decoupled the relationship between the Seebeck coefficient and the electrical resistivity. The Seebeck coefficient and resistivity of Ni/Te samples increased by 37.9% and decreased by 28.1%, respectively. Meanwhile, the thermal conductivity of the Ni/Te samples decreased by 25.8% (T = 300 K), and the zT value was increased by 36.4% compared to the pure Te sample. Consequently, a peak zT of 0.96 at 550 K is achieved in 18wt %Ni/Sb 0.003 Te 0.997 sample,which is 50% higher than Sb 0.003 Te 0.997 samples. This work indicates that electroless plating combined with spark plasma sintering is an effective method to construct heterojunction in bulk materials. This method should be widely applicable to various materials for achieving better thermoelectric properties.
研究领域:
材料科学
·
凝聚态物理
·
能源材料
·
半导体物理
·
热电转换
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）