Applied Materials Today
·
2024
·
IF 7.2
Lingyan Zheng,Zhen Liu,Shuwen Xin,Qi Chen,Jinbo Ming,Liren Wu,Jiaqi Xu,Peilong Xu,Kai Liu,Ramakrishna Seeram,Fengyun Wang
A pivotal characteristic of neuromorphic systems lies in their inherent capacity for self-adaptation, facilitating environmental adaptation through the attenuation of response to repetitive stimuli. Existing electrolyte-gated synaptic transistors face challenges in simulating these self-adaptive behaviors of the brain. In this work, flexible indium zinc tin oxide (IZTO) nanowires-based synaptic transistors exhibiting self-adaptive behavior were fabricated for the first time via a facile electrospinning technique. The prepared transistors can realize typical synaptic functions by continuously modulating the conductance, including excitatory/inhibitory postsynaptic current and short/long term potentiation. These properties are well maintained even under a bending radius of 12 mm. Additionally, the neuromorphic system based on IZTO nanowires-based transistors achieves a high recognition accuracy exceeding 90 % for hand-written digits recognition. The synaptic transistor exhibits obvious self-adaptive behavior and a low energy consumption with reduction of 8.2 %. Self-adaptive neuromorphic flexible transistors can not only enhance their resemblance to biological systems, but also advance the development of wearable devices and neuromorphic calculation.
研究领域:
材料科学
·
纳米科技
·
生物电子学
·
神经形态工程
·
柔性电子器件
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2019
·
IF 8.355
Kuan Wu,Gang Xu,Dengyu Pan,Minghong Wu
Combination of high-capacity and flexibility in electrode materials is crucial for flexible electronics. Recently, red phosphorus (P) has caused increasing focus as a hopeful storage material for lithium storage due to its super-high theoretical capacity and low cost. However, the low conductivity of red P and its large volume change during cycling process lead to reduced electrochemical activity. So far, no effective methods have been developed to construct flexible binder-free electrodes using red P as an active material for high-performance lithium-ion batteries (LIBs). Here, a novel hollow three‐dimensional (3D) internet structure as a flexible high-areal-capacity electrode material was fabricated by confining red P nanoparticles into compact MOF-derived carbon-based composite polyhedrons/carbon nanotube internets. The electrode manifests an excellent lithium storage performance for LIBs with a high discharge capacity of 4.78 mAh cm −2 (1920 mAh g −1 ) at 0.1 mA cm −2 and a good capacity retention of 79.2% at 1 mA cm −2 after 300 cycles (73% and 69% capacity retention at 5 and 10 mA cm −2 after 500 cycles, respectively). The novel flexible anode materials can provide excellent Li + storage performance for flexible electronics applications.
研究领域:
材料科学
·
电化学
·
纳米材料
·
能源存储
·
功能材料
·
先进电池技术
✓ 已验证
DOI
高影响因子
Journal of Healthcare Engineering
·
2022
·Vol. 2022
·期 1
·2271937
·
IF 3.822
Xiangwen Yuan,Jiabin Zhang
Glaucoma is caused by excessive aqueous humor in the eye, resulting in a continuous or intermittent increase of intraocular pressure, which exceeds the tolerance of the eyeball and damages the optic nerve. Existing treatments for glaucoma do not work well or have significant side effects. Intraocular pressure signal is a very important physiological signal that needs real-time and accurate monitoring in glaucoma patients, especially in severe glaucoma patients. Therefore, long-term, real-time, and accurate monitoring of intraocular pressure is of great significance for the diagnosis and treatment of glaucoma patients. The use of wearable devices for real-time ocular diagnosis and treatment of glaucoma patients is an effective approach. However, the current commonly used intraocular pressure measurement and monitoring technology is difficult to meet the diagnosis and monitoring needs of glaucoma patients in terms of size, measurement accuracy, power consumption, and intelligence. Therefore, facing the needs of glaucoma disease treatment, this topic studies an implantable flexible intraocular pressure sensor for long-term continuous monitoring of intraocular pressure in glaucoma patients and mainly focuses on the working principle, structural design, process fabrication, measurement and control system, characterization, and performance test of the intraocular pressure sensor. It is of great significance for personalized and accurate treatment of glaucoma patients.
研究领域:
眼科
·
生物医学工程
·
传感器技术
·
转化医学
·
慢性病管理
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2015
·
IF 4.504
Peng Zhang,Zhimeng Liu,Yuping Liu,Hongbo Fan,Yuanqi Jiao,Baiman Chen
In this work, we demonstrate a facile approach to synthesize high-performance and stable TiO 2 @PANI core-shell nanowires (NWs) as flexible electrodes for solid-state supercapacitors (SCs). The TiO 2 @PANI core-shell NWs are grown directly on highly conductive carbon cloth, which not only give efficient charge transport and accessible diffusion of the electrolyte, but also provide large surface area and active sites for redox reaction as well as good strain accommodation. Such these features enable them to deliver a large areal capacitance of 520.3 mF/cm 2 at 0.5 mA/cm 2 with outstanding rate capability. Furthermore, a flexible and stable solid-state SC device based on these TiO 2 @PANI core-shell NWs is also demonstrated. The as-fabricated solid-state SC device yields a remarkable volumetric capacitance of 898.4 mF/cm 3 , excellent flexibility and significant cycling stability with more than 97.2% retention of its capacitance after 10000 cycles. We believe that these findings may open up new opportunities to prepare high-performance PANI-based electrodes for flexible solid-state SCs.
研究领域:
材料科学
·
纳米科技
·
电化学
·
能源存储
·
功能材料
·
柔性电子学
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2019
·Vol. 3
·期 9
·2237-2245
·
IF 4.912
Yulin Chen,Yu Li,Fengnan Yao,Cong Peng,Chen Cao,Yiyu Feng,Wei Feng
Two-dimensional (2D) graphene-based materials are widely applied as electrodes for supercapacitors due to their vast surface area and excellent charge mobility. However, the pursuit of the theoretical capacitance of graphene has lasted besides the improvements of charge/discharge rate and cycling life. In this work, a nitrogen and fluorine co-doped holey graphene hydrogel (NF-HGH) was synthesized by using consecutive solvothermal treatments for creating vacancies on the graphene basal plane and introducing heteroatoms into the graphene framework. The NF-HGH as an electrode for supercapacitors exhibited a remarkable electrochemical performance of 345.4 F g−1 at 1 A g−1 in 6 M KOH electrolyte. In addition, the specific capacitance of the assembled all-solid-state flexible symmetric supercapacitor (SSC) was 67.3 F g−1 at 1 A g−1, with an outstanding long-term cycling stability over 10 000 cycles. The delivered maximum energy and power densities were 7.99 W h kg−1 and 10.08 kW kg−1, respectively. The abundant pyrrolic-N doped at the edge of etched vacancies and the formed semi-ionic C–F bonds around pyrrolic-N were critical for electrochemical developments, which provided a sensational method to construct carbonaceous frameworks for energy storage systems.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
功能材料
✓ 已验证
DOI
高影响因子
RSC Advances
·
2018
·Vol. 8
·期 33
·18690-18697
·
IF 2.936
Qian Liu,Zijie Xu,Wu Qiu,Chen Hou,Yanan Wang,Peijian Yao,Rui Yu,Wenxi Guo,Xiang Yang Liu
Ultraflexible electronics have received extensive attention due to their favorable properties, such as superior mechanical robustness, light weight and good compatibility with large-area roll-to-roll fabrication. Here we present a flexible sandwiched tungsten trioxide/silver nanotrough network/poly(3,4-ethylenedioxythiophene)–poly(styrene sulfonate) multi-layer transparent conducting electrode with prominent conductivity (sheet resistance as low as 1.08 Ω sq−1) and transparency (85%). In particular, the flexible transparent electrode exhibits excellent mechanical robustness upon bending and stretching. This hybrid electrode can be further adhered tightly to a layer of WO3 to form an electrochromic device, which simultaneously displays a rapid switching time (0.75 s/1.82 s for bleaching/coloring) and high cyclic performance (86% retention of the initial optical contrast after cycling for 30 000 s). In addition, our electrode can also be fabricated on various flexible substrates, such as polyethylene cling wrap, polydimethylsiloxane and Ecoflex, with sustained electrochromic properties after bending, twisting, stretching and even strong kneading. Our work provides new opportunities for the next generation of flexible and wearable electronics applied on various flexible substrates.
研究领域:
材料科学
·
纳米科技
·
柔性电子学
·
功能材料
·
电化学
·
高分子材料
·
器件物理
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2017
·
IF 6.395
Zhiliang Chen,Guang Yang,Xiaolu Zheng,Hongwei Lei,Cong Chen,Junjie Ma,Hao Wang,Guojia Fang
Perovskite solar cells have developed rapidly in recent years as the third generation solar cells. In spite of the great improvement achieved, there still exist some issues such as undesired hysteresis and indispensable high temperature process. In this work, bulk heterojunction perovskite-phenyl-C 61 -butyric acid methyl ester solar cells have been prepared to diminish hysteresis using a facile two step spin-coating method. Furthermore, high quality tin oxide films are fabricated using pulse laser deposition technique at room temperature without any annealing procedure. The as fabricated tin oxide film is successfully applied in bulk heterojunction perovskite solar cells as a hole blocking layer. Bulk heterojunction devices based on room temperature tin oxide exhibit almost hysteresis-free characteristics with power conversion efficiency of 17.29% and 14.0% on rigid and flexible substrates , respectively.
研究领域:
材料科学
·
光伏技术
·
纳米材料
·
能源材料
·
半导体器件
·
薄膜制备
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2016
·
IF 6.333
Qianlong Zhou,Chunyang Jia,Xingke Ye,Zhonghua Tang,Zhongquan Wan
At present, the topic of building high-performance, miniaturized and mechanically flexible energy storage modules which can be directly integrated into textile based wearable electronics is a hotspot in the wearable technology field. In this paper, we reported a highly flexible fiber-shaped electrode fabricated through a one-step convenient hydrothermal process. The prepared graphene hydrogels/multi-walled carbon nanotubes-cotton thread derived from natural cotton thread is electrochemically active and mechanically strong. Fiber-shaped supercapacitor based on the prepared fiber electrodes and polyvinyl alcohol-H 3 PO 4 gel electrolyte exhibits good capacitive performance (97.73 μF cm −1 at scan rate of 2 mV s −1 ), long cycle life (95.51% capacitance retention after 8000 charge-discharge cycles) and considerable stability (90.75% capacitance retention after 500 continuous bending cycles). Due to its good mechanical and electrochemical properties , the graphene hydrogels/multi-walled carbon nanotubes-cotton thread based all-solid fiber-shaped supercapacitor can be directly knitted into fabrics and maintain its original capacitive performance. Such a low-cost textile thread based versatile energy storage device may hold great potential for future wearable electronics applications.
研究领域:
材料科学
·
纳米技术
·
柔性电子学
·
能源存储
·
纺织工程
✓ 已验证
DOI
高影响因子
ADVANCED FUNCTIONAL MATERIALS
·
2019
·Vol. 29
·期 38
·1904416
·
IF 15.621
Huai Yang,Longfei Pan,Xiaoting Wang,Hui-Xiong Deng,Mianzeng Zhong,Ziqi Zhou,Zheng Lou,Guozhen Shen,Zhongming Wei
Mixed-valence states can bring unexpected unique phenomena, especially novel anisotropic physics, due to structural asymmetry, which originate from the discrepant distribution of atoms with different valence. This study reports an unexploited mixed-valence-driven quasi-1D Sn II Sn IV S 3 crystal, which exhibits widely and distinctively anisotropic polarized-light absorption reaching ≈3.4 from the deep ultraviolet to near-infrared region (250–850 nm). The fabricated polarization-sensitive photodetectors based on highly air-stable Sn II Sn IV S 3 nanowires display strong linear dichroism among the UV–vis–NIR spectrum with responsivity exceeding ≈150 A W −1 . Furthermore, the devices are further constructed onto a flexible polyethylene terephthalate (PET) substrate and the photoresponse remains roughly unchanged after repeated bending. This work based on novel mixed-valence-driven quasi-1D ternary sulfide Sn II Sn IV S 3 excites interest in low-symmetry semiconductors for developing broadly spectral polarization-sensitive photodetectors with environmental stability and mechanical flexibility.
研究领域:
材料科学
·
半导体物理
·
纳米光学
·
光电子学
·
凝聚态物理
✓ 已验证
DOI
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2024
·Vol. 130
·期 8
·547
·
IF 2.5
Geriletu,Gu Hao
Flexible silicone materials have excellent elastic properties and can maintain excellent structural stability under high-intensity repeated deformation. They are ideal materials for preparing piezoresistive flexible sensors. However, traditional silicone materials exhibit strong insulation properties. The solid block structure is also not conducive to improving sensitivity. Inspired by the irregular hole structure of Taihu Lake stone, this paper prepared a porous silica gel skeleton (rGO/CTAB/SG) based on reduced graphene oxide film coating, which was equipped with flexible interdigital electrodes to achieve electrical signal derivation. The “honeycomb” shaped sensing module prepared in this way achieves an extremely wide elastic deformation range (20-200%). In the pressure feedback layer, the rGO film is evenly coated on the SG surface, which greatly improves the device conductivity and sensing performance (high sensitivities of 89.4 kPa − 1 and 25.4 kPa − 1 are achieved within 0-30.2 kPa and 30.2–42 kPa, ultra-high durability under more than 22,000 load-unload cycles.) Numerical simulation analysis results confirmed that the structure of the flexible substrate SG prepared by this method maintained well when extreme deformation occurred, and no fracture or stress concentration occurred. As an elastic sensor, after being integrated with a microprocessor, it can easily monitor and analyze human body movement in real time. It has huge potential in areas such as daily training and health monitoring of athletes.
研究领域:
生物医学工程
·
柔性电子
·
运动医学
·
可穿戴传感器
·
力学传感
·
功能材料
✓ 已验证
DOI
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2023
·Vol. 129
·期 10
·682
·
IF 2.7
Yin Chunmei,Li Qinghua,Lu Zhiyi,Shi Yaochen,Lin Wei
A highly sensitive pressure-sensitive sensor based on MXene was developed using the electrostatic self-assembly method, with carbide sponges as the elastic substrate and a rational design. Specifically, CTAB was used to treat the carbide triamine sponge and conduct the electrostatic self-assembly with MXene to achieve a tightly combined conductive filler and substrate. The resulting pressure sensor showed excellent performance, with a high sensitivity of 15.05 kPa −1 under a range of 0–20 kPa, a response time of 0.1 s, and high durability under 2000 loading–unloading cycles. The minimum detection limit of the sensor was as low as 0.3 Pa, demonstrating excellent monitoring performance. Additionally, finite-element simulation analysis showed that MXene@CTAB@CMF had even better sensing performance at the same stress level. Moreover, the pressure sensor exhibited good sensing performance for various physiological signals and daily work monitoring of the human body, indicating its potential application value.
研究领域:
生物医学工程
·
纳米医学
·
柔性电子学
·
传感技术
·
材料科学
✓ 已验证
DOI
高影响因子
Advanced Materials Interfaces
·
2020
·Vol. 7
·期 7
·1901815
·
IF 4.948
Minglong Yang,Qiang Wei,Jianjun Li,Yao Wang,Hongfei Guo,Liya Gao,Li Huang,Xiaodong He,Yibin Li,Ye Yuan
Inspired by the traditional Chinese “pancake-making” method, the efficient electromagnetic interferences (EMI) shielding composite carbon films are conveniently obtained by assembling graphene oxide (GO) sheets, carbon nanotubes (CNTs), and Co/C nanocomposites into a laminated “nacre-like” structure. The developed composite carbon films are characterized by a shielding effectiveness (SE) up to ≈51 dB in X band with a small thickness of ≈34.3 µm. Moreover, the composite carbon film shows favorable flexibility and the SE values almost keep a constant after repeatedly bending test. These results demonstrate a promising approach to simply fabricate a flexible and highly efficient EMI shielding material.
研究领域:
材料科学
·
纳米科技
·
复合材料
·
电磁功能材料
·
柔性电子学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）