FUEL
·
2022
·
IF 8.035
Zhanshi Ni,Haobo Bi,Chunlong Jiang,Hao Sun,Wenliang Zhou,Zhicong Qiu,Qizhao Lin
Faced with increasingly severe environmental and energy issues, the development and utilization of solid waste have become a trend. In this study, a thermogravimetric-Fourier infrared spectrometer-mass spectrometer (TG-FTIR-MS) was used to carry out the co-pyrolysis experiment of coal slime and cellulose. The samples with mass mixing ratios of 0:10, 1:9, 3:7, 5:5, 7:3, 9:1, and 10:0 were pyrolyzed in N 2 atmosphere. The percentages of mass loss during the pyrolysis of coal slime and cellulose were 15.69 and 94.28%, respectively. The addition of cellulose to the coal slime could significantly improve the pyrolysis performance of the sample. It was detected by FTIR that the pyrolysis of the blends mainly formed C=O-containing compounds. MS was used to monitor the ion current intensity of gaseous products of sample pyrolysis online. The average activation energy of the reaction between coal slime and cellulose calculated by the Kissinger-Akahira-Sunose method were 237.59 kJ/mol and 174.06 kJ/mol, respectively. The principal component 1 and principal component 2 dominated the co-pyrolysis process of coal slime and cellulose. The MAE, RMSE, and R 2 of the artificial neural network prediction model for predicting the pyrolysis process of the sample were 0.5249, 0.8244, and 0.9994, respectively. This research provided basic theory and data support for understanding the co-pyrolysis of coal slime and biomass.
研究领域:
能源化学
·
环境科学
·
热化学转化
·
可再生能源
·
固体废物利用
✓ 已验证
DOI
高影响因子
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS
·
2020
·
IF 3.905
Yanshuxian Liu,Yilei Fan,Zhongping Huang,Huijun Liu,Lili Wang,Zhenlu Shen,Ichi Watanabe
A novel method based on on-line pyrolytic methylation-gas chromatography/mass spectrometry was established and applied into rapid determination of γ-hydroxybutyric acid (GHB) in human hair. With the pyrolytic methylation by tetramethylammonium hydroxide (TMAH), GHB was converted into its corresponding methyl ester in the pyrolyzer at 500 °C. Thus, GHB in hair samples could be well determined by GC/MS on a capillary column in SIM mode. To obtain optimum methylation conditions, important factors were investigated and then applied to the following experiments. The results were obtained as following: 500 °C as reaction temperature, 2:1 as the proportion of TMAH to GHB. The achieved calibration curve exhibited good linearity with the correlation coefficient of 0.9997 at the concentraion range of 2−200 ng/mg, and relative standard deviation (n = 3) from 1.3 %–7.7 %. The limit of detection and the limit of quantification were down to 0.3 ng/mg and 1.0 ng/mg, respectively. The precision ranged from 2.0 %–7.9 % and the recovery ranged from 98.5 %–107.4 %. The results of on-line pyrolytic methylation-GC/MS were in agreement with those observed by the referenced off-line silylation-GC/MS method. The method was applied to a real case of a woman addicted to GHB, the drug concentration in hair segments of 0−5 cm and 5−10 cm from the root strand well correlated with the use of GHB in different periods of her life. The proposed method demonstrated significant potential in the application of rapid determination for GHB in human hair.
研究领域:
法医毒理学
·
药物代谢
·
分析化学
·
生物样本分析
·
临床化学
✓ 已验证
DOI
高影响因子
COMBUSTION AND FLAME
·
2024
·
IF 5.8
Hong Wang,Bingzhi Liu,Qiang Xu,Shijun Dong,Zhandong Wang,Long Zhu
Cyclopentanone (CPN) is a widely available biofuel with excellent combustion properties, but detailed speciation profiles during its pyrolysis have rarely been studied. This work examines the pyrolysis of CPN in a jet-stirred reactor (JSR) at atmospheric pressure, with residence time of 2 s and a temperature range from 830 K to 1100 K. Dozens of pyrolysis intermediates and products were measured using synchrotron vacuum ultraviolet photoionization mass spectrometry (SVUV-PIMS) and gas chromatography (GC). Among them, several new species were observed, including water, carbon dioxide , formaldehyde, indene , 1,2-dihydroindene, naphthalene , 1,2-dihydronaphthalene, 1-methylnaphthalene, acenaphthylene , biphenyl , and fluorene . A detailed kinetic model was developed based on the literature, and in general, it predicted the experimental results for most species well. Kinetic analyses indicated that the consumption of CPN was controlled by the bimolecular reactions with H atom. The formation of water, carbon dioxide and formaldehyde could be explained by the reaction pathways of OH radical. The pyrolysis of CPN yielded a significant number of alkenes and alkynes at higher temperatures; the bimolecular addition reactions of these species with resonantly stabilized radicals are important to the formation of polycyclic aromatic hydrocarbons (PAHs). Based on those, this work provides valuable insights into CPN pyrolysis chemistry and it promotes the development of a comprehensive CPN combustion model.
研究领域:
燃烧化学
·
能源化学
·
反应动力学
·
分析化学
·
环境化学
✓ 已验证
DOI
高影响因子
BIORESOURCE TECHNOLOGY
·
2020
·
IF 7.539
Kaijun Wang,Sining Yun,Tian Xing,Bingjie Li,Yasir Abbas,Xinming Liu
The effects of binary and ternary trace elements (TEs) (Fe/Co, Fe/Ni, and Fe/Co/Ni) on the anaerobic digestion (AD) of cattle manure were investigated using kinetic models (first-order, logistic, modified Gompertz, and Coats-Redfern) and experimental measurements. Binary and ternary TEs can significantly improve the biogas production rate and yield potential. The deviation between the predicted and measured data for biogas yield with logistic model (2.1%–5.3%) and modified Gompertz model (0.32%–2.9%) was smaller than that with first-order kinetic model (6.9%–9.9%). The Coats-Redfern model fitting indicated that the activation energy of digestates with trace elements during pyrolysis was reduced by 3.9%–26.2% compared with the control group. Meanwhile, digestates with TEs showed remarkable fertility (5.72%–5.95%). The combination of kinetic models and experimental measurements can effectively quantify the effect of TEs on AD performance and provide an informed choice for industrial production.
研究领域:
环境科学
·
农业工程
·
生物质能源
·
废物资源化
·
生物化学工程
✓ 已验证
DOI
高影响因子
BIORESOURCE TECHNOLOGY
·
2016
·
IF 4.917
Hao Li,Samah Awadh Ali Mahyoub,Wenjie Liao,Shuqian Xia,Hechuan Zhao,Mengya Guo,Peisheng Ma
The magnetic biochars were easily fabricated by thermal pyrolysis of Fe(NO 3 ) 3 and distillation residue derived from rice straw pyrolysis oil at 400, 600 and 800 °C. The effects of pyrolysis temperature on characteristics of magnetic biochars as well as adsorption capacity for aromatic contaminants (i.e., anisole, phenol and guaiacol) were investigated carefully. The degree of carbonization of magnetic biochars become higher as pyrolysis temperature increasing. The magnetic biochar reached the largest surface area and pore volume at the pyrolysis temperature of 600 °C due to pores blocking in biochar during pyrolysis at 800 °C. Based on batch adsorption experiments, the used adsorbent could be magnetically separated and the adsorption capacity of anisole on magnetic biochars was stronger than that of phenol and guaiacol. The properties of magnetic biochar, including surface area, pore volume, aromaticity, grapheme-like-structure and iron oxide (γ-Fe 2 O 3 ) particles, showed pronounced effects on the adsorption performance of aromatic contaminants.
研究领域:
环境科学
·
环境工程
·
材料科学
·
物理化学
·
污染控制化学
·
能源材料
·
吸附科学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Yu Zhou,Wenjun Zhou,Chunhua Ni,Shenggang Yan,Liangmin Yu,Xia Li
Precursors of a nickel-based metal–organic framework, denoted Ni-MOF, and the loofah plant were prepared by the microwave method, and “tree blossom” Ni/Nitrogen doped Carbon (NC)/ Carbon (C) composites were prepared by in situ pyrolysis under an argon atmosphere. During pyrolysis, the morphology, specific surface area, porous structure and electromagnetic parameters of the Ni/NC/C composites were adjusted by adjusting the pyrolysis temperature. The maximum reflection loss of the corresponding Ni/NC/C composites can reach −63.1 dB at 13.84 GHz and a thickness of 2 mm when the pyrolysis temperature was 650 ℃ and the filling amount was 16 wt%. And the effective absorption bandwidth was 35.44 GHz when the thickness was adjusted from 1 mm to 5.5 mm within the range of 2–40 GHz. Excellent performance comes from conduction loss, dipole and interface polarization, magnetic resonance, multiple electromagnetic reflections and scattering, and equilibrium impedance matching.
研究领域:
材料科学
·
纳米复合材料
·
电磁功能材料
·
能源材料
·
环境功能材料
✓ 已验证
DOI
高影响因子
Solar RRL
·
2019
·Vol. 3
·期 5
·1800346
·
IF 0
Jiang Cheng,Rong Hu,Kun Wang,Xiang Meng,Ying Li,Xin Yang,Xiaoqing Liao,Lu Li,Kok Boon Chong
Antimony chalcogenide is a promising absorber material for photovoltaic (PV) cells because of its tunable band gap, strong optical absorption, earth-abundant, and nontoxic constituents. Here, a novel hydrazine-free approach for fabricating antimony chalcogenide films prepared via spray pyrolysis deposition with further selenylation, as well as high performance solar cells are reported. The fabricated antimony chalcogenide solar cells exhibits remarkably high open-circuit voltage ( V OC ) comparing with that of Sb 2 Se 3 and Sb 2 S 3 devices. The distribution of Se during the selenylation process via refering to the Fick's second law is discussed. The results show that the selenized absorber has tremendously improved absorbance for visible light and a cascade-type energy level from surface to bulk, resulting in an ideal energy level matching for p-n junction. By introducing an efficient buffer layer, the detrimental short-circuit is avoided by reducing the cracks. Finally, 4.57% of the power conversion efficiency (PCE) of the solar cell is achieved. Furthermore, a module with a large-scale active area of 21 cm 2 is successfully fabricated, which shows a PCE of 3.19%, and a V OC of 3.42 V. The present work suggests that the antimony chalcogenide solar cells are promising for industrial application.
研究领域:
材料科学
·
光伏技术
·
半导体器件
·
能源材料
·
薄膜制备
·
表面工程
·
器件物理
✓ 已验证
DOI
CERAMICS INTERNATIONAL
·
2020
·Vol. 46
·期 16
·25802-25807
·
IF 3.83
Jun Xiao,Yan Jia,Dongqing Liu,Haifeng Cheng
Manufacturing complexity and poor machinability hinder the preparation of complex-shaped ceramic composites. Three-dimensional printing can overcome this difficulty. Herein, we report a type of photocurable preceramic resin containing SiO 2 nanoparticles (up to 20 wt% of polymer), which do not affect the photocurability of the preceramic resin, and a small amount of SiC nanofibres (1 wt%). We successfully printed precise green bodies with a complex shape by digital light processing and converted them into ceramic composites via pyrolysis at 1300 °C under a N 2 atmosphere. The introduction of SiO 2 and SiC into the ceramic composites led to reduced weight loss of the composites during pyrolysis and a decrease in their porosity and enhancement in their mechanical properties after pyrolysis. The properties of the printed samples pyrolysed at different ramping rates were compared, and the effects of the microstructure on the mechanical properties of the composites were investigated.
研究领域:
材料科学
·
陶瓷工程
·
增材制造
·
高分子转化陶瓷
·
复合材料
✓ 已验证
DOI
高影响因子
COMBUSTION AND FLAME
·
2021
·
IF 4.185
Zhi-Hao Jin,Jin-Tao Chen,Wang Li,Shu-Bao Song,Jiu-Zhong Yang,Zhen-Yu Tian
Owing to significant advantages over traditional biofuels, 2-methylfuran (MF) has arisen extensive interest as next generation biofuels . Atmospheric pressure pyrolysis of a 1:1 blend of MF with a three-component (3C) surrogate jet fuel was conducted in a flow tube using synchrotronphotoionization and molecular beam mass spectrometry techniques within a temperature range of 898–1223 K. Therein, the 3C surrogate fuel consists of 66.2% n-dodecane (NC 12 H 26 ), 18.0% 1,3,5-trimethylcyclohexane (T135MCH) and 15.8% n-propylbenzene (NPB, A1C 3 H 7 ). The detailed kinetic model including 579 species and 3474 reactions was developed via validating against both measured and literature data with reasonable agreement. MF exhibits no obvious influence on the 3C components pyrolysis . However, 3C mixtures play an important roles in MF decomposition: lower initial temperature and different decomposition pathways. In the meantime, n-propylbenzene (NPB) pyrolysis curve in 3C and 3C+MF significantly transfers to low temperature zone after 1000 K in contrast to pure NPB, while smaller change was found in the decomposition curve of n-dodecane. Compared with 3C pyrolysis, 3C+MF blends have less formation of aromatic species and light hydrocarbons except for vinylacetylene (C 4 H 4 ) and acetylene (C 2 H 2 ). Allyl radical (C 3 H 3 ) has significant roles in benzene ring formation. The combination of allyl radical with propargyl radical producing benzene and H radical (aC 3 H 5 + C 3 H 3 = A1 + 2H) has the highest contribution to the benzene formation in both 3C and 3C+MF. Moreover, most of naphthalene (A2) formation is also related to C 3 H 3 radical via reaction: A1CH 2 + C 3 H 3 = A2 + H, rather than via HACA (hydrogen abstraction carbon addition) reaction. Interaction of fuel blends was mainly presented through the common and important sensitive reactions which are much to do with CH 3 and H radicals. The overview of product distribution was investigated by providing comparisons of carbon conversion rates during the pyrolysis of 3C and 3C+MF. These results will be helpful to better understand the pyrolysis properties of MF/jet fuel surrogate blends and could contribute to developing new generation biofuels for aviation.
研究领域:
燃料化学
·
燃烧动力学
·
生物燃料
·
能源化学
·
反应机理
·
质谱分析
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）