JOURNAL OF APPLIED POLYMER SCIENCE
·
2019
·Vol. 136
·期 36
·47922
·
IF 2.188
Nan Pan,Juanrong Qin,Yuwei Fan,Zeke Li,Botao Song
In this study, mesoporous silica nanoparticles (MSNs) were embedded into the hydrophilic poly(vinyl alcohol) (PVA) nanofibrous mats to achieve sustained release of water soluble drug from hydrophilic nanofibrous mats. MSNs were successfully prepared based on a sol–gel method. Water soluble drug naproxen sodium was then loaded into the mesopores of the MSNs, and different amounts of the drug-loaded MSNs were further incorporated into the fibers by the electrospinning process. Morphology of the nanofibrous mats was investigated, and it was found that all the fibers exhibited fibrous structure. Interestingly, lots of protrusions could be observed from the scanning electron microscopy images with high magnification, and numbers of the protrusions increased with the increasing of loading ratios of the MSNs from 5 to 15%. In addition, the wetting behaviors of the nanofibrous mats were also measured, and the water contact angles of all the mats were measured to be 0°. Finally, the drug release results indicated that all the PVA/MSNs composite nanofibrous mats showed an obviously prolonged drug release. The optimal loading ratio of the MSNs in the nanofibers was 10% due to the slowest drug release rate. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136 , 47922.
研究领域:
药剂学
·
生物材料
·
纳米医学
·
药物递送系统
·
高分子科学
✓ 已验证
DOI
高影响因子
PHYSICA STATUS SOLIDI A-APPLICATIONS AND MATERIALS SCIENCE
·
2020
·Vol. 217
·期 6
·1900536
·
IF 1.759
Parisa Zeaiean Firouzabadi,Hajar Ghanbari,Nafiseh Mahmoudi,Seyed Mohammad Amin Haramshahi,Jafar Javadpour
Polymer-based composites are used for wound healing applications. This work aims to prepare an inorganic-polymer nanocomposite based on bentonite, poly(vinyl alcohol), and bacterial cellulose by electrospinning for wound healing. The nanocomposite is synthesized using a solution intercalation technique, with 1–2 wt% nanobentonite concentration variation. The effects of commercial and laboratory-synthesized nanobentonite as well as the extract of the green walnut shell (EGWS) are examined and characterized by different techniques. The addition of nanobentonite increases the average size of fibers and tensile strength up to 200 nm and more than 15 MPa, respectively, due to the presence of hydrogen bonding formed between the nanobentonite sheets and polymer matrix. By the addition of synthetic nanoclay and EGWS, moderate elongation and strength are achieved. The hydrophilicity shows a decreasing trend up to 2 wt% of commercial nanobentonite; however, the laboratory-synthesized nanobentonite is not significantly effective. Effects of extracts on the viability of cultured human adipose tissue–derived mesenchymal stem cells (ADSCs) are quantitated, where the samples containing 1–2 wt% of commercial nanobentonite have less toxicity than others. Antibacterial activity is tested against both Escherichia coli and Staphylococcus aureus bacteria according to the agar diffusion test for 72 h, in which EGWS-based mats exhibit strong antimicrobial activity.
研究领域:
生物材料学
·
组织工程
·
纳米医学
·
再生医学
·
药剂学
·
微生物学
·
高分子科学
✓ 已验证
DOI
高影响因子
MACROMOLECULAR RAPID COMMUNICATIONS
·
2011
·Vol. 32
·期 21
·1729-1734
·
IF 4.371
Juanping Hu,Xianfeng Wang,Bin Ding,Jinyou Lin,Jianyong Yu,Gang Sun
Electro-spinning/netting (ESN) as a cutting-edge technique evokes much interest because of its ability in the one-step preparation of versatile nano-fiber/net (NFN) membranes. Here, a controllable fabrication of polyurethane (PU) NFN membranes with attractive structures, consisting of common electrospun nanofibers and two-dimensional (2D) soap bubble-like structured nano-nets via an ESN process is reported. The unique nanoscaled NFN architecture can be finely controlled by regulating the solution properties and several ESN process parameters. The versatile PU nano-nets comprising interlinked nanowires with ultrathin diameters (5–40 nm) mean that the NFN structured membranes possess several excellent characteristics, such as an extremely large specific surface area, high porosity and large stacking density, which would be particularly useful for applications in ultrafiltration, special protective clothing, ultrasensitive sensors, catalyst support and so on.
研究领域:
材料科学
·
高分子化学
·
纳米技术
·
膜科学
·
生物医学工程
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2018
·
IF 5.116
Meng Wan,Han Zhu,SongGe Zhang,HaoNan Jin,YanKun Wen,LiNa Wang,Ming Zhang,MingLiang Du
Oxygen evolution reaction (OER) plays an important role in various renewable energy systems . Owing to its complex four-electron redox process , the OER process with sluggish kinetics often requires electrocatalysts to reduce the overpotential and promote the reaction rate. Herein, we have proposed an “all-in-one” strategy to synthesize mutil-elemental perovskite oxides nanofibers (NFs) with hollow and porous structures by using electrospinning technology and Ostwald ripening approach. The hollow La 0.7 Sr 0.3 Co 0.25 Mn 0.75 O 3 nanofibers (LSCM NFs) consist of large amounts of building block La 0.7 Sr 0.3 Co 0.25 Mn 0.75 O 3 nanoparticles (LSCM NPs), forming the unique architecture and the morphologies can be engineering by adjusting the calcination temperatures and the heating rates . Notably, the hollow LSCM NFs prepared at 800 °C and 10 °C min −1 demonstrated the excellent electrocatalytic performance, with overpotential of 340 mV at current density of 10 mA cm −2 and Tafel slope of 111 mV dec −1 , as well as the long-term stability in alkaline electrolyte . The hollow NFs architectures exhibited a large specific surface area , a high porosity and a large inner space, which are beneficial for the OER, reducing the overpotentials and accelerating the electrode kinetics .
研究领域:
材料化学
·
电化学
·
纳米材料科学
·
能源催化
·
功能材料
·
可再生能源
✓ 已验证
DOI
高影响因子
Advanced Energy Materials
·
2017
·Vol. 7
·期 15
·1700087
·
IF 16.721
Ting Jin,Yongchang Liu,Yang Li,Kangzhe Cao,Xiaojun Wang,Lifang Jiao
NaVPO 4 F has received a great deal of attention as cathode material for Na-ion batteries due to its high theoretical capacity (143 mA h g −1 ), high voltage platform, and structural stability. Novel NaVPO 4 F/C nanofibers are successfully prepared via a feasible electrospinning method and subsequent heat treatment as self-standing cathode for Na-ion batteries. Based on the morphological and microstructural characterization, it can be seen that the NaVPO 4 F/C nanofibers are smooth and continuous with NaVPO 4 F nanoparticles (≈6 nm) embedded in porous carbon matrix. For Na-storage, this electrode exhibits extraordinary electrochemical performance: a high capacity (126.3 mA h g −1 at 1 C), a superior rate capability (61.2 mA h g −1 at 50 C), and ultralong cyclability (96.5% capacity retention after 1000 cycles at 2 C). 1D NaVPO 4 F/C nanofibers that interlink into 3D conductive network improve the conductivity of NaVPO 4 F, and effectively restrain the aggregation of NaVPO 4 F particles during charge/discharge process, leading to the high performance.
研究领域:
材料科学
·
电化学
·
纳米技术
·
能源存储
·
无机非金属材料
·
固态化学
✓ 已验证
DOI
高影响因子
SENSORS AND ACTUATORS A-PHYSICAL
·
2021
·
IF 3.407
Wenbo Jiang,Kongsen Hu,Nan Lv,Zhiwei Lyu
Existing piezoelectric sensing materials usually rely on top and bottom planar electrodes to achieve the assembly of piezoelectric sensors , restricting their application due to the limitation of flexibility and miniaturization as well as time-consuming and costly multi-steps preparation. Here, we report a simple strategy to synchronously construct piezoelectric elements and nanoresistance networks via fabricating single PAN/PANI/PVP piezoelectric-conductive nanofibers (NFs) by electrospinning. By virtue of PAN as piezoelectric elements and PANI/PVP as nanoresistance networks, the flexible PAN/PANI/PVP piezoelectric-conductive NFs as an integrated sensing system can timely collect and output voltage based on Wheatstone bridge principle. The pressure sensing potential of flexible PAN/PANI/PVP integrated nanofibers membrane (INFM) is systematically explored and evaluated. The valid contact and adhesion of piezoelectric elements and nanoresistance networks improve effective polarization and collection of induced charges, enhancing piezoelectric output performance. Moreover, it enables the INFM to perceive tiny force with high-precision sensitivity (667 mV N −1 ) down to approximately 0.05 N while retaining a linear relationship. Thus, our research opens a simple route to design integrated sensing materials with nanoscale , high-sensitivity, lightweight and low-cost, making them attractive candidates in the potential application in micro-/nanoscale sensors and wearable electronics .
研究领域:
生物医学工程
·
纳米医学
·
柔性电子学
·
传感器技术
·
可穿戴设备
·
功能材料
·
微纳系统
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2018
·
IF 2.955
Yuhua Dong,Siyi Li,Qiong Zhou
The self–healing capability of epoxy coatings modified with coaxial core–shell nanofibers loaded with the corrosion inhibitor 2–mercaptobenzothiazole (MBT) was investigated using electrochemical techniques. The polyvinyl alcohol/polyvinylidene fluoride core–shell nanofibers were prepared by coaxial electrospinning. Electrochemical impedance results showed that the MBT–loaded coaxial nanofibers improved the barrier properties and decreased the corrosion activity of the coatings. Results of the Scanning Kelvin Probe technique revealed that the MBT–loaded coaxial nanofibers healed corrosion over artificial defects exposed to NaCl electrolytes. These results indicate that adding MBT–loaded coaxial nanofibers to epoxy coatings is a promising strategy toward the development of self–healing epoxy coatings.
研究领域:
材料科学
·
高分子化学
·
腐蚀与防护
·
表面工程
·
功能材料
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2012
·
IF 3.832
Pingfan Du,Lixin Song,Jie Xiong,Ni Li,Zhenqiang Xi,Longcheng Wang,Dalai Jin,Shaoyi Guo,Yongfeng Yuan
Novel TiO 2 /ZnO core–sheath nanofibers (NFs) film was fabricated through an extraordinary coaxial electrospinning technique . Dye-sensitized solar cells (DSSCs) were assembled using the TiO 2 /ZnO NFs film as photoanode . FESEM , TEM, FTIR , XRD , XPS and UV–vis were used to characterize the NFs electrode film. Photocurrent–voltage ( I – V ) characteristic, incident photo-to-current conversion efficiency (IPCE) spectrum, and electrochemical impedance spectroscopy (EIS) measurements were performed to evaluate the DSSCs performance. The results reveal that the DSSCs based on the TiO 2 /ZnO core–sheath NFs are superior to their bare TiO 2 NFs-based counterparts. Compared with the latter, the overall energy conversion efficiency was enhanced from 4.47 to 5.17%. And the possible mechanism for this enhancement was discussed.
研究领域:
材料科学
·
纳米技术
·
能源材料
·
光电化学
·
半导体薄膜
✓ 已验证
DOI
高影响因子
MATERIALS LETTERS
·
2017
·
IF 2.572
Shu-Hui Xia,Shu-Hua Teng,Peng Wang
Polyvinyl alcohol/silica (PVA/SiO 2 ) hybrid fibers were prepared via a sol–gel combined electrospinning technique, and their potential application in bone tissue engineering was evaluated in terms of in vitro bioactivity. When the PVA concentration was 8%, the obtained PVA/SiO 2 hybrid fibers exhibited a uniform and continuous morphology, with an average fiber diameter of about 542.9 nm. The SiO 2 xerogel phase was uniformly distributed within the PVA matrix, and its actual content was very close to the theoretical value. After 3 days of immersion in simulated body fluid (SBF), the PVA/SiO 2 hybrid fibers displayed a vigorous precipitation of lamellar apatite crystals, reflecting their excellent in vitro bioactivity.
研究领域:
生物材料学
·
组织工程
·
纳米医学
·
生物医学工程
·
无机非金属材料
·
再生医学
✓ 已验证
DOI
高影响因子
EUROPEAN POLYMER JOURNAL
·
2015
·
IF 3.005
Hongwei Zhang,Qijian Niu,Ning Wang,Jun Nie,Guiping Ma
In this research a thermo-sensitive drug loaded core–shell fibers were prepared by UV photo-polymerization combined with electrospinning technology. The biodegradable polymer polylactic acid (PLA) was used as the core with electrospinning and the N-isopropylacrylamide (NIPAM) was selected to be shell of the fibers via UV photo-polymerization, respectively. Combretastatin A4 (CA4) was used as the model drug loaded in PLA (core structure) to test the thermo-sensitivity of the core–shell fibers. SEM was performed to observe the morphology of the fibers. TEM was carried out to confirm the core–shell structure of the fibers. Furthermore, XPS and FTIR results demonstrated that the core–shell structure had been fabricated as designed. Water contact angle (WCA) test indicated that the fibers show different wettability when the temperature was below or above the lower critical solution temperature (LCST). Moreover, in vitro drug release test was conducted to explore the difference of the drug release when the temperature was at 25 °C and 40 °C. The cell culture studies showed that the prepared core–shell structure nanofibers have a potential application in the biomedical fields as tissue engineering.
研究领域:
生物材料
·
药物递送
·
组织工程
·
高分子科学
·
纳米医学
✓ 已验证
DOI
高影响因子
JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALS
·
2016
·Vol. 105
·期 6
·1369-1378
·
IF 2.881
Bing Wang,Jun Dong,Lijing Niu,Wenyan Chen,Dongliang Chen,Chengyi Shen,Jiang Zhu,Xiaoming Zhang
Electrospun membranes of poly(p-dioxanone-co- l -phenylalanine) (PDPA) hold potential as an anti-adhesion material. Since adjustable degradation properties are important for anti-adhesion materials, in this study, the in vitro and in vivo degradation processes of PDPA electrospun membranes were investigated in detail. The morphological analysis of these membranes revealed the main degradation conditions of PDPA membranes. The weight remaining and molecular weight variation showed that the overall degradation rate of the membranes could be adjusted by modulating the molecular structure of the PDPAs. Especially, α-chymotrypsin could catalyze the degradation process of PDPAs. Based on these results, the in vitro degradation mechanism was demonstrated, and confirmed by 1 H NMR of the hydrolysis products. Finally, the in vivo degradation and biocompatibility of different PDPAs were investigated. The kinetic study showed that the in vitro and in vivo molecular weight loss of PDPAs have the first-order characteristics. The in vivo degradation rate of the most Phe-containing PDPA-3 is the slowest, and this result relates to the biocompatibilities of PDPAs. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1369–1378, 2017.
研究领域:
生物材料学
·
组织工程
·
高分子科学
·
生物医学工程
·
药物递送
·
再生医学
·
生物降解
✓ 已验证
DOI
高影响因子
Nanoscale
·
2019
·Vol. 11
·期 34
·15881-15891
·
IF 6.97
Yong Xu,Jun Chen,Ze'en Xiao,Caixia Ou,Weixia Lv,Lihong Tao,Shengwen Zhong
A porous composite electrode composed of diatomite-mixed 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTCDA) is prepared by electrostatic spinning technology. Compared with traditional coated electrodes without diatomite mixing, the obtained composite electrode materials have higher porosity, larger specific surface area and faster lithium ion transport channels, which makes them exhibit better electrochemical performance, such as smaller impedance, higher capacity, and better cycling stability and rate performance. The electrospun diatomite-mixed 1,4,5,8-NTCDA composite (ED-1,4,5,8-NTCDA) electrode shows an initial coulombic efficiency of 77.2%, which is much higher than that of the electrospun 1,4,5,8-NTCA (E-1,4,5,8-NTCDA) electrode without diatomite mixing (63.8%) and the coated 1,4,5,8-NTCA (C-1,4,5,8-NTCDA) electrode (48.3%). Moreover, the ED-1,4,5,8-NTCDA electrode displays an initial discharge capacity of 1106.5 mA h g−1, which is much higher than that of the E-1,4,5,8-NTCDA electrode (546.0 mA h g−1) and the C-1,4,5,8-NTCDA electrode (185.4 mA h g−1). After 200 cycles, the capacity of the ED-1,4,5,8-NTCDA electrode remains at 1008.5 mA h g−1 with a retention ratio of 91.2%, which is also much higher than that of 753.2 mA h g−1 for the E-1,4,5,8-NTCDA electrode and 288.1 mA h g−1 for the C-1,4,5,8-NTCDA electrode. Even at a higher current density of 1500 mA g−1, its capacity remains above 508.9 mA h g−1. The ED-1,4,5,8-NTCDA electrode presents superior performance, which opens up a promising new approach for further utilization of organic materials as electrode materials in rechargeable lithium-ion batteries.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
功能材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）