PHOTOCHEMISTRY AND PHOTOBIOLOGY
·
2013
·Vol. 89
·期 5
·1262-1268
·
IF 2.287
Zhi-Yuan Yan,Bing Yan
Rare earth doped fluorides (BaMgF 4 , aYF 4 and BaYF 5 /BaLuF 5 ) have been synthesized and dispersed in an ionic liquid compound, (3-triethoxysilyl) propyl-3-methylimidazolium chloride (denoted as IM + Cl − ). Through the cohydrolysis and copolycondensatoin reaction between the alkoxy group (3-triethoxysilyl) of IM + and tetraethoxysilane in the presence of carboxylic acids (formic acid) as catalyst and water source, luminescent hybrid ionogels form subsequently. 1 H NMR spectroscopy, X-ray diffraction, transmission electron microscopy, scanning electron microscopy and especially up-conversion (UC) luminescence spectroscopy are used to characterize the precursors and the resulted hybrid ionogels. These hybrid ionogels exhibit the UC luminescence properties of immobilized rare earth fluoride nanocrystals (BaMgF 4 , NaYF 4 and BaYF 5 /BaLuF 5 ) doped Er 3+ /Tm 3+ , Yb 3+ .
研究领域:
材料科学
·
纳米科技
·
无机化学
·
功能材料
·
光子学
✓ 已验证
DOI
高影响因子
MATERIALS RESEARCH BULLETIN
·
2017
·
IF 2.446
Tengchao Guo,Guoyue Xu,Shujuan Tan,Ning Liu,Jianchao Zhang,Xiangxiong Zeng,Juan Liang
The electronic properties and infrared emissivity of Zn 1-x Mg x O (x = 0, 0.0625, 0.125) were systematically investigated by using the first-principle calculation s based on density functional theory (DFT). The Zn 1-x Mg x O (x = 0, 0.0625, 0.125) powders were prepared by sol-gel method and their infrared emissivity in the wavelength of 8–14 μm was characterized. The results indicate that the infrared emissivity increases with the increase in Mg concentration, which is attributed to the reduction in conductivity and in the real part of dielectric function. Furthermore, the variation in conductivity and dielectric function has been well studied, and a reasonable method to calculate infrared emissivity of semiconductors has been established. It is expected that this method can be used for designing materials with different infrared emissivity and also applied for effectively guiding the experimental investigation.
研究领域:
材料科学
·
凝聚态物理
·
计算材料学
·
功能材料
·
半导体物理
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Bo Zhu,Lingyu Zhou,Qi Zhang,Xiaodong Wang,Hongmei Jiang,Aimin Lu
A rigid Pb(II)-imprinted polymers were synthesized by the combination of surface-imprinted method with sol–gel method using (3-mercaptopropyl) trimethoxysilane as a functional monomer, Pb(II) and hexadecyltrimethylammonium bromide as template ions and tetraethoxysilane as cross-linker and were used as adsorbents for the removal of Pb(II). The effect of molar ratio of cross-linker to functional monomer on the morphology and adsorption performance has been evaluated. The effects of pH, initial concentration and adsorption time on the adsorption performance of Pb(II) on both sorbents were investigated. The maximum adsorption capacity calculated from Langmuir isotherm was 68.03 mg g -1 and 17.13 mg g -1 for Pb(II)-IIP and Pb(II)-NIP, respectively. Kinetics studies showed that the adsorption process obeyed the pseudo-second-order kinetic model. The selective adsorption coefficient of Pb(II)-IIP for Pb(II)/Ni(II), Pb(II)/Cd(II), Pb(II)/Hg(II) and Pb(II)/Co(II) are 117.5, 1.42, 4.9 and 30.24, respectively. The spent Pb(II)-IIP could be reused at least five cycles, demonstrating its good practicability.
研究领域:
环境化学
·
材料科学
·
分析化学
·
环境污染治理
·
功能高分子材料
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2020
·
IF 4.65
Zhixin Yao,Yuandong Peng,Chao Xia,Xuwu Yi,Shenghua Mao,Miantuan Zhang
The effect of calcination temperature on the coating layer and the phase of the alloy matrix is the main problem to improve the heat treatment process of SMCs and obtain excellent magnetic properties . In this study, FeNiMo@Al 2 O 3 powders which were coated by sol-gel and calcined at 900–1300 °C were prepared and these powders were pressed into SMCs. The results showed that the surface of the powder was uniformly coated with Al 2 O 3 . As the heat treatment temperature increases, the phase of the coating changed from AlOOH to γ-Al 2 O 3 , δ-Al 2 O 3 , θ-Al 2 O 3 , and α-Al 2 O 3 . Meanwhile, the new phase γ-Fe, Ni appeared in the alloy matrix. The magnetic permeability of the sample is very stable in the frequency range of 10–500 kHz. The magnetic loss decreases first and then increases, with a minimum at 1100 °C. The permeability and magnetic loss of the sample pressed from the powder obtained by calcination at 1100 °C are 321.78 mw/cm 3 and 87.61 (50 kHz, 100 mT) at the typical industrial application conditions of Iron–Nickel SMCs. The microstructure and the magnetic properties show that the obtained α-Al 2 O 3 have excellent insulation and heat resistance. This resulted in a significant reduction in core losses of FeNiMo SMCs.
研究领域:
材料科学
·
磁性材料
·
无机非金属材料
·
粉末冶金
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2017
·
IF 3.133
Chunmin Wang,Jun Shen,Xiankun Zhang,Bin Duan,Jiaxin Sang
A new organic-inorganic composite coating was generated on AZ31 alloy surface with sol-gel method to improve the anti-corrosion performance and biocompatibility of AZ31 alloy in the physiological environment. The results of electrochemical impedance spectroscopy (EIS), potentiodynamic polarization , pH variations in modified-simulated body fluid (m-SBF) demonstrated that the silane/Mg(OH) 2 composite coating significantly enhanced the anti-corrosion ability and slowed down the degradation of AZ31 alloy under in vitro condition. Fourier-transform infrared spectroscopy (FTIR) showed that the major composition of in-situ formation layer was Mg(OH) 2 . The surface morphology , chemical and phase constitutions of the composite coating were detected using scanning electron microscopy (SEM). The results demonstrated that the composite coating was uniform and defect-free. X-ray diffraction analysis (XRD) was also employed to characterize the corrosion products of all specimens immersed in m-SBF after 30 days. MTT and ALP tests indicated that the composite coating greatly enhanced the cell proliferation and osteogenic differentiation of osteoblasts on the AZ31 alloy surface.
研究领域:
生物材料学
·
表面工程
·
组织工程
·
生物医学工程
·
腐蚀科学
·
骨科学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Rui Huang,Hongye Wang,Cheng Tao,Hua Hao,Zhonghua Yao,Hanxing Liu,Minghe Cao
Thin film capacitors with large energy storage density and high breakdown strength are widely used in modern electronic fields. To solve the problems of interface effect and different polarization mechanism between matrix and fillers in conventional heterogeneous structure composite thin film capacitors, a new-type inorganic microcrystal-amorphous composite film of 0.92BaTiO 3 -0.08Bi(Ni 0.5 Zr 0.5 )O 3 (0.92BT-0.08BNZ) are prepared by sol–gel method. The amorphous matrix improving the breakdown strength is introduced into the film by adjusting preparation technology. Moreover, the nano-scale polar microcrystalline regions (fillers) are introduced and uniformly distributed in the amorphous matrix under various annealing temperatures. Through investigating the influence of different amorphous matrix and microcrystal trend on the dielectric and energy storage properties, it is found that synergistic effect between the polarized microcrystalline regions and the amorphous matrix are optimal at an annealed temperature of 550 ℃. The result shows that a high energy storage density of 103.7 J cm −3 and an efficiency of 88.3% are obtained under the electric field of 8.30MV cm −1 . Simultaneously, the excellent dielectric and energy storage stability is achieved in a wide temperature range of 20–200 °C. Conclusively, this microcrystal-amorphous composite film overcome the low energy storage capability and poor thermal stability of conventional composite films and provide a feasible way for preparing high energy storage performance films.
研究领域:
材料科学
·
介电材料
·
储能技术
·
无机非金属材料
·
功能薄膜
✓ 已验证
DOI
高影响因子
JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY
·
2013
·Vol. 66
·期 1
·133-138
·
IF 1.66
Peng Shusen,Zhao Wenjie,Zeng Zhixiang,Li He,Xue Qunji,Wu Xuedong
In this report, hybrid silica sol–gel coating was prepared using Ce(NO 3 ) 3 (Sol-Ce) as catalyst. Structure, surface morphology and anticorrosion ability of Sol-Ce solution/coating were studied by infrared spectroscopy (IR), scanning electron microscopy, energy dispersive spectrometer (EDS), potentiodynamic scan (PDS) and electrochemical impedance spectroscopy (EIS). IR results showed that Ce(NO 3 ) 3 had a stronger influence on reactivity of alkoxysilane. EDS results revealed that the fraction of Fe in Sol-Ce coating was significantly lower than regular acid-catalyzed hybrid silica sol–gel coating (Sol-Ac) and Sol-Ac with Ce(NO 3 ) 3 -doped coating (Sol-Ac/Ce). The results of PDS and EIS demonstrated that Sol-Ce coating had better anticorrosion ability than Sol-Ac and Sol-Ac/Ce on carbon steel. The enhanced anticorrosion performance of the Sol-Ce coating might result from the following two reasons: (a) Ce(NO 3 ) 3 as a catalyst could alleviate the negative effects of low pH with using acid catalyst (dissolution of carbon steel) and (b) Ce(NO 3 ) 3 could impede corrosion of carbon steel as corrosion inhibitor.
研究领域:
材料科学
·
表面工程
·
腐蚀与防护
·
无机化学
·
电化学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2024
·
IF 13.3
Bing Yang,Bo Wang,Peng Li,Jing Chen,Bo Li,Lushan Ma,Futian Zhang,Haitao Guo,Yunfeng Tian,Xuzhuo Sun,Bo Chi
In this study, we developed an innovative strategy to fabricate perovskite oxide powder with 12.356 m 2 /g of specific surface area. Polyacrylamide hydrogel was used as a template to prepare Sm 0.5 Sr 0.5 CoO 3-δ (SSC) powders with lamellar structure. The three-dimensional interconnected structured SSC electrodes with lamellar connections were fabricate using screen printing method. As a result, the oxygen vacancy concentration of the SSC powder obtained by the polyacrylamide template method was 0.625 and 0.642 at 650 °C and 700 °C respectively. At 650°C, the polarization resistance value was 0.11 Ω cm 2 for the novel SSC-PAM-V cathode. Compared with the SSC-SG cathode, the polarization resistance and activation energy of SSC-PAM-V were reduced by 50 % and 6.9 %, respectively. Furthermore, in a single cell with SSC-PAM-V electrodes, we achieved a maximum power density of 935 and 1243 mW cm −2 at 650 °C and 700 °C under wet H 2 conditions, demonstrating good electrochemical output performance. The layered porous electrode was not only suitable for the diffusion of oxygen, but also for increasing the reactive active sites. The proposed powder prepared with polyacrylamide hydrogel as template, was not only suitable for the optimization of perovskite oxide, but also for the application in other types of catalysis, providing the potential for improving the electro-catalytic activity of perovskite electrodes.
研究领域:
材料科学
·
电化学
·
能源材料
·
催化化学
·
固体离子学
✓ 已验证
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2020
·Vol. 22
·期 23
·13214-13222
·
IF 3.43
Yongfang Yuan,Xiaowen Zhang,Dongliang Li,Xiuyun Zhang,Lihui Wang,Zongliu Lu,Liming Liu,Feng Chi
Hole injection governs the efficiency of ultraviolet organic light-emitting diodes (UV OLEDs) due to the deep highest occupied molecular orbital level of the emissive molecule. Tungsten oxides (WOx), transition metal oxides with high work functions and good stability, cast light on solving this problem. By a low-cost, scalable and high-throughput manufacturing process, herein the facile synthesis of a WOx solution and its doping in poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS + WOx) is systematically investigated for assembling efficient UV OLEDs. X-ray diffraction, atomic force microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy measurements confirm that WOx and PEDOT:PSS + WOx have good film morphology and exceptional electronic properties, such as the oxygen deficiency dominated non-stoichiometry of WOx. With PEDOT:PSS + WOx tailoring hole injection and 2-(4-biphenyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole as the emitter, the UV OLEDs show outstanding electro-optic performance, with a radiance of 3.98 mW cm−2, external quantum efficiency of 2.30%, electroluminescence peak at 400 nm and full width at half maximum of 47 nm, which is superior to the performance of the corresponding reference materials. The mechanism of charge transfer from the PEDOT polycation to WOx, enhancing conductivity, is responsible for the robust hole injection/transport and is further elucidated by ultraviolet photoelectron spectroscopy and impedance spectroscopy, contributing to the optimization of the carrier balance and recombination zone. Our results illustrate an alternative approach for boosting UV OLED performance and advancing organic electronics.
研究领域:
材料科学
·
有机电子学
·
薄膜器件
·
光电功能材料
·
半导体器件物理
✓ 已验证
DOI
高影响因子
MATERIALS LETTERS
·
2017
·
IF 2.572
Shu-Hui Xia,Shu-Hua Teng,Peng Wang
Polyvinyl alcohol/silica (PVA/SiO 2 ) hybrid fibers were prepared via a sol–gel combined electrospinning technique, and their potential application in bone tissue engineering was evaluated in terms of in vitro bioactivity. When the PVA concentration was 8%, the obtained PVA/SiO 2 hybrid fibers exhibited a uniform and continuous morphology, with an average fiber diameter of about 542.9 nm. The SiO 2 xerogel phase was uniformly distributed within the PVA matrix, and its actual content was very close to the theoretical value. After 3 days of immersion in simulated body fluid (SBF), the PVA/SiO 2 hybrid fibers displayed a vigorous precipitation of lamellar apatite crystals, reflecting their excellent in vitro bioactivity.
研究领域:
生物材料学
·
组织工程
·
纳米医学
·
生物医学工程
·
无机非金属材料
·
再生医学
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2013
·Vol. 129
·期 4
·2313-2320
·
IF 1.395
Mingchao Luo,Xiaoxue Liao,Shuangquan Liao,Yanfang Zhao
Waste rubber powder (WRP) was modified by microwave, sol–gel method, and both microwave and sol–gel method, respectively. The mechanical and dynamic mechanical properties of natural rubber (NR)/modified WRP composite were investigated. The influence of bis-(3-(triethoxysilyl)-propyl)-tetrasulfide (TESPT) content on curing characteristics and mechanical properties of vulcanizate was also studied. The results showed that NR/WRP modified by both microwave and sol–gel method composite owned the best mechanical properties. Rubber processing analyzer was used to characterize the interaction between silica and rubber chains and the dispersion of silica. With increase of TESPT content, the Payne effect decreased. Scanning electron microscopy indicated the coherency and homogeneity of in situ generated silica filled vulcanizate. Dynamic mechanical analyzer showed that NR/WRP modified by both microwave and sol–gel method composite with 5 phr TESPT exhibited the lower tan δ at temperature range of 50–80°C, compared with composite without TESPT and the higher tan δ at temperature of 0°C, compared with the conventional modification of WRP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013
研究领域:
高分子材料科学
·
橡胶工程
·
复合材料学
·
材料化学
·
高分子物理
·
功能材料
·
可持续材料技术
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2020
·Vol. 46
·期 10
·16524-16532
·
IF 3.83
Muhammad Yousaf,Asma Noor,Shuai Xu,Majid Niaz Akhtar,Baoyuan Wang
Yttrium iron garnet (YIG) nanoparticles (NPs) doped with rare earth (RE) metal ions (Y 2.5 Sm 0.5 Fe 5 O 12 , Y 2.5 Nd 0.5 Fe 5 O 12 ) were successfully synthesized by sol-gel auto combustion approach. The cubic crystalline structure and morphology of the prepared garnet ferrite NPs were analyzed by X-ray diffractometer (XRD) and field emission scanning electron microscopy (FESEM). The cubic crystalline garnet phase of the synthesized YIG, Sm-YIG and Nd-YIG samples was successfully achieved at 950 °C sintering temperature . The force constant and absorption bands were estimated by using Fourier transform infrared spectroscopy (FTIR). The doping effect of RE metal ions on the chemical states of YIG were examined by x-ray photoelectron microscopy (XPS). The valence band (from 12.63 eV to 13.22 eV), conduction band (from 10.89 eV to 11.34 eV) edges and optical bandgap values of RE doped YIG samples were calculated using UV–Vis spectroscopy and ultraviolet photo electron spectroscopy (UPS). The magnetic analysis of the prepared NPs was studied using vibrating sample magnetometer (VSM). The XPS analysis of RE doped YIG samples exhibit the existence of RE (Sm +3 , Nd +3 ) contents on the surface of YIG ferrite by decreasing the oxygen lattice in garnet structure. The optical bandgap (from 1.74 eV to 1.88 eV) explains the semiconducting nature of the synthesized NPs. The UPS results confirm the valence band position of YIG doped samples. The saturation magnetization and remanence of RE doped garnet ferrite samples increased from 13.45 to 18.83 emu/g and 4.06–6.53 emu/g, respectively.
研究领域:
材料科学
·
纳米科技
·
固体物理
·
无机化学
·
功能材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）