International Journal of Electrochemical Science
·
2023
·
IF 1.5
Yanxia Liu,Xiuquan Yao,Chunlin Liu,Xiaofang Luo,Chao Guo,Wei Du
Electrochemical and SEM methods were used to study domperidone (DPD) as an organic corrosion inhibitor for X60 carbon steel in 1 M hydrochloric acid solution. The corrosion inhibition rate decreases with increasing corrosion inhibitor concentration. The inhibition efficiency was the highest when 400 mg/L DPD inhibitor was added, showing a type of mixed inhibitor. The adsorption of DPD inhibitor on the steel surface conforms to the Langmuir isotherm as a combination of physical and chemical adsorption. In addition, the adsorption conformation of the inhibitor molecules on the steel surface was analyzed by MD calculations and the adsorption energy was calculated.
研究领域:
材料科学
·
电化学
·
表面科学
✓ 已验证
产品关联
DOI
高影响因子
ChemistrySelect
·
2025
·Vol. 10
·期 14
·e202405719
·
IF 2
Zhengquan Zhang,Yuling Wang
Graphical AHNPs are prepared with complexing agent and deposition agent by aqueous solution deposition.The AHNPS's structures are confirmed through FTIR, XRD, and SEM.The reaction temperature have an effect on the size and phase of AHNPs and the degree of the aggregation.A formation mechanism of the AHNPs is represented. In this work, aluminate hydrate nanoparticles were successfully prepared with complexing agent (ethylenediamine) and deposition agent (hydrazinehydrate) by aqueous solution deposition.The aluminate hydrate nanoparticles were analyzed by FTIR, XRD, and SEM. The reaction temperature have an effect on the size and phase of aluminate hydrate nanoparticles, and the degree of the aggregation.When the temperature was at below 80°C, aluminate hydrate nanoparticles were mainly composed of Al(OH) 3 nanoparticles with nordstrandite phase;when the temperature was over 80°C, aluminate hydrate nanoparticles were mainly AlOOH nanoparticles with boehmite phase.The sizes of Al(OH) 3 nanoparticles were in the range of 50–200 nm with a good quality of dispersion, and the size of AlOOH nanoparticles were in the range of 300–800 nm with part of agglomeration and little dispersion.A formation mechanism of the AlOOH and Al(OH) 3 NPs was represented.
研究领域:
材料科学
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
Defence Technology
·
2020
·
IF 2.637
Yue-ting Wang,Xiao-ting Zhang,Jian-bing Xu,Yun Shen,Cheng-ai Wang,Fu-wei Li,Ze-hua Zhang,Jian Chen,Ying-hua Ye,Rui-qi Shen
In this study, Al–CuO nanocomposites were fabricated by sol-gel method. As a contrast, the thermite was prepared by physical mixing at the equivalence ratio of 0.5, 1, 2, respectively. The intermediates and samples as prepared were characterized by SEM and XRD. The exothermic properties of the two samples prepared at different equivalence ratios were tested and the reaction products were characterized by XRD. The SEM results show that the sample prepared by the sol-gel method demonstrates a micron-sized agglomerated sphere formed by a mutual wrapping of Al NPs and CuO NPs, and the particles are evenly distributed in the agglomerate. In addition, when the content of Al powder is seriously insufficient, the heat release of the sample prepared by physical mixing is 1.6 times that of by sol-gel method. With the increase of Al powder content, the exothermic properties of Al/CuO NPs prepared by sol-gel method began to increase significantly compared with physical mixing and the difference is 1.5 times when the equivalence ratio increases to 2. It can be concluded that the reason for this result may be attributed to the different mass transfer modes of components due to the different morphologies of samples.
研究领域:
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
POWDER TECHNOLOGY
·
2025
·
IF 4.6
Shuo Zhang,Hanqing Wang,Li Cheng,Wei Fang,Yonglin Qiu,Lijun Yang,Ruijin Liao
The dispersion of nanoparticles in nanocomposites seriously affects the material properties. However, the current nanoparticle dispersibility assessment mainly relies on the microscopic imaging method, which has the limitations of being lossy and having a narrow detection area, and is unable to realize the assessment of the overall dispersibility of the particles in bulk materials. This article uses nonlinear ultrasonic technology (NLUS) to achieve the overall dispersion evaluation of nanoparticles. Theoretical and experimental results show that: the nanoparticles nonlinear coefficient (Δ β ) and the particle agglomeration degree ( K ) approximately satisfy the linear variation relationship (R 2 > 0.9), while the smaller the elastic modulus of the particles is, the larger the slope of the Δ β -K fitting function is; the results of the NLUS test are not affected by the factors of surface modification. The error between the NLUS nondestructive evaluation results of particle dispersion and the SEM lossy test results ranged from 3 % to 15 %. The single detection region of NLUS is a three-dimensional region of ultrasonic wave propagation and the single detection time is short, these features enable NLUS to be applied in the rapid non-destructive evaluation of the overall dispersion of large volume polymer-based nano-dielectric material particles.
研究领域:
材料科学
·
超声波检测
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2021
·
IF 7.312
Xi Zhang,Mingzhu Huangfu,Jiushuai Deng,Yu Wang,Bozeng Wu,Mingzhen Hu,Honghui Zhao,Suozhi Wu
Specularite is generally recovered by flotation, but its floatability is relatively weak. Activation is an effective method to improve the floatability of minerals. Therefore, finding an economic and effective activator to improve the recovery of specularite is an important research direction. In this study, lead nitrate as an activator was found and confirmed to improve the floatability of specularite. Its activation mechanism was further investigated by various analytical methods. The micro-flotation tests results showed that the recovery of specularite increased from 69.57% to 92.47% at a Pb 2+ concentration of 3 × 10 -5 mol/L, an approximately 23% increase, indicating that Pb 2+ could obviously activate specularite. The SEM-EDS results illustrated that the content of Pb on the specularite surface apparently increased after specularite treatment with lead nitrate, which confirmed the adsorption of Pb species on the surface of specularite. Zeta potential results showed that the zeta potential positively shifted within the pH range from 3 to 11, which was beneficial to the occurrence of electrostatic adsorption and chemisorption between negatively charged oleate species and specularite. XPS results revealed that lead species mainly adsorbed on the O atoms of Fe-O and Fe-OH at the specularite surface, and Pb atoms became new sites to interact with sodium oleate. In addition, Pb 2+ and Pb(OH) + were the predominant components that interacted with the specularite surface and formed -O-Pb and Fe-O-Pb complexes, which considerably increased the number of reactive sites on the specularite surface. After oleate components interacted with Pb-modified specularite, a denser hydrophobic layer was generated on the surface of specularite, which intensified the floatability of specularite.
研究领域:
矿物加工
·
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2022
·
IF 6.206
Shuhui Liu,Hui Xie,Qingmin Cao,Yujie Ning,Yihan Song,Chengdong Zhang,Bin Liu
This research aims to improve the protective performance of coatings in harsh corrosive conditions by using functionalized self-healing microcapsules. CeO 2 /PUF MCs and PUF MCs were prepared via one-step emulsion polymerization . The microcapsules were implanted into epoxy coatings to investigate their self-healing performance. Multiple testing techniques, including SEM, FTIR, XRD , TGA , EIS , and NSS were used to characterize the morphology, crystal structure, chemical composition, thermal properties, and self-healing performance of the microcapsules and coatings. The experimental results indicated that the CeO 2 /PUF MCs had a spherical core-shell structure with a rough surface and an average diameter of 1583 nm. Meanwhile, the minimum corrosion products and the highest low-frequency impedance were found in CeO 2 /PUF MCs coating with artificial scratch, which demonstrated that the self-healing and anti-corrosion performance were significantly improved by the newly developed bi-functional microcapsules.
研究领域:
材料科学
·
涂层技术
·
腐蚀科学
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED MICROBIOLOGY
·
2025
·
IF 3.2
Zhang Chuhan,Qin Lijun
AimsTo determine the optimum conditions for extracting Eucommia ulmoides gum (EUG) from Eucommia ulmoides leaves during fermentation by Coprinellus disseminatus. At the same time, the EUG characteristics were characterized.Methods and resultsThe ability of C. disseminatus to secrete degrading enzymes, including enzyme activity and lignocellulose content, was observed by culturing C. disseminatus on a medium with different formulations. Based on the optimal formula, the fermentation conditions were determined by an orthogonal test and EUG was extracted. After that, the characteristic parameters of EUG were determined by FT-IR, 1H-NMR, SEM, POM, DSC, XRD and GPC. The results showed that the lignin and hemicellulose contents in Eucommia leaves decreased significantly with the increase of fermentation days, and C. disseminatus mediated fermentation had an obvious damage effect on the tissue of Eucommia leaves. At the same time, At the same time, xylan can be used as an initiator to induce the expression of degradation-related enzymes. The extraction yield of EUG from Eucommia ulmoides leaves after fermentation was 3.06%, which was significantly improved. The optimum fermentation conditions were 4% inoculum, 28°C fermentation temperature, and pH = 5. The results of infrared FT-IR and 1H-NMR showed that the extract had typical characteristics of EUG, and the surface and quenching part of the EUG were smooth, as observed by SEM. In addition, DSC and XRD analysis show that there are two crystal types, α and β, in the crystallization process of molten EUG. The main crystallization type of EUG extracted from fermented leaves was β type.ConclusionThe ability of C. disseminatus to produce degrading enzymes can effectively improve the extraction rate of EUG under optimal fermentation process. The method can maintain the integrity of gutta-percha better. EUG has the characteristics of good crystallinity, many β crystal types and high molecular weight.
研究领域:
生物技术
·
生物化学
·
材料科学
·
植物学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF DISPERSION SCIENCE AND TECHNOLOGY
·
2022
·
IF 2.042
Jun Cao,Qi Sun,Peng Wang,Jie Shen,Xue Dai
In order to solve the problem that separating zeolite 4A from solutions, we have synthesized Fe3O4/zeolite 4A magnetic nanocomposite by hydrothermal method. It is characterized by Transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR), Vibrating Sample Magnetometer (VSM), scanning electron microscope (SEM) and Brunner-Emmet-teller (BET). The XRD result shows that Fe3O4/zeolite 4A magnetic nanocomposite has a good crystal structure. It also shows that Fe3O4/zeolite 4A magnetic nanocomposite contains two phases of zeolite 4A and Fe3O4 MNP. The optimal sample (Z-2) was judged by the calculation of crystallinity. The successful combination of zeolite 4A and Fe3O4 MNP was visually observed through SEM technology. The functional groups of Fe3O4/zeolite 4A magnetic nanocomposite were characterized by FTIR technology. The TEM result shows that some Fe3O4 MNPs enter zeolite 4A, which further clarifies the microstructure of Fe3O4/zeolite 4A magnetic nanocomposite. N2 adsorption-desorption technique confirms that Fe3O4/zeolite 4A magnetic nanocomposite SBET is 55.3374 m2/g and Dave is 9.7128 nm. VSM result shows that Fe3O4/zeolite 4A magnetic nanocomposite magnetization is 18.4534 emu/g. Simulation experiment shows that Fe3O4/zeolite 4A magnetic nanocomposite exhibit a fast response to an external magnetic field.
研究领域:
材料科学
·
纳米技术
·
化学工程
·
磁性材料
✓ 已验证
产品关联
DOI
高影响因子
Biomass Conversion and Biorefinery
·
2022
·Vol. 14
·期 4
·5295-5304
·
IF 4.05
Tong Dongshen,Chen Xingtao,Dong Yuxiao,Fang Zhi,Zhang Hao,Zhou Chunhui,Yu Weihua
Kaolinite is a layered silicate material with a Janus character and has been directly used as the solid catalyst for the hydrolysis of cellulose in our previous work. Reducing sugar (RS) is one of the most important intermediates for the utilization of cellulose. In the present study, metal ions dispersed on kaolinite was easily prepared and further evaluated for the hydrolysis of cellulose to RS in water. The metal ions dispersed kaolinite was characterized by XRD, BET, SEM(EDS), and XPS. The catalytic results showed that copper was the best co-catalyst among the tested metal ions and the kaolinite treated with 4(wt)% copper nitrate by calcination at 623 K showed the highest total reducing sugar (TRS) yield of 51% under 478 K with the mass ratio of catalyst to cellulose of 0.2 and weight ratio of water to cellulose of 7 for 3 h. Moreover, the catalyst could be easily regenerated by calcination and the yield of TRS on the regenerated catalyst decreased from 51 to 43.2% after four times reuse. The characterization results revealed that copper was highly dispersed on the outer SiO 4 tetrahedral layer. The surface cuprous species were the active sites and could make the C-O bond cleavage easily by attacking the positively charged carbon atoms of the β-(1,4)-glycosidic linkage in the cellulose. The leaching of the cuprous species was responsible for the deactivation of the catalyst. The copper dispersed kaolinite is the efficient catalyst for the hydrolysis cellulose to reducing sugars and worth further development. Graphical abstract
研究领域:
催化
·
材料科学
·
环境化学
·
绿色化学
·
高分子科学
✓ 已验证
DOI
高影响因子
RSC Advances
·
2015
·Vol. 5
·期 105
·86620-86624
·
IF 3.84
Tao Wang,Huiping Zhang,Ying Yan
A novel porous zeolite beta coating/PSSF composite was prepared by secondary growth method in fluoride media. The morphology of zeolite beta coating/PSSF composite was characterized by SEM and the structural and textual properties of composite were characterized by XRD and N2 adsorption/desorption isotherms on ASAP 2020, respectively. The thermal stability of composite was analyzed by thermogravimetry (TG) and differential scanning calorimetry (DSC). The results indicated that well-intergrown and continuous zeolite beta coating with highly crystallinity were successfully synthesized on the surface of paper-like stainless steel fibers support. The structures of zeolite beta coating/PSSF composite were three-dimensional network with large void volume and majority of microporous structure. The thickness of zeolite beta coating on stainless steel fibers is approximate 2 μm. The specific surface area (SBET) and the total pore volume of composite were 118 m2 g−1 and 0.067 cm3 g−1, respectively. The composite was stable at temperature up to 650 °C.
研究领域:
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
APPLIED CLAY SCIENCE
·
2019
·
IF 3.89
Haiyan Yang,Yang Zhou,Dongshen Tong,Miao Yang,Kai Fang,Chunhui Zhou,Weihua Yu
Cellulose is the most abundant form of biomass on earth, and is considered as an alternative for fuels and chemicals. The hydrolysis of cellulose to platform compounds, such as reducing sugars (RS), is one of the most important ways for the utilization of cellulose. In this study, the solid acid catalysts of SO 4 2− -ZrO 2 /montmorillonite (SZ-Mt) were prepared by coupling SO 4 2− with ZrO 2 and then introducing into the interlayer of Mt using the coprecipitation method. Meanwhile, the catalytic performance of the SZ-Mt catalysts for the hydrolysis of cellulose to RS in water was studied. The catalysts were characterized by XRD , FT-IR, BET, SEM(EDS), NH 3 -TPD and XPS . The catalytic results showed that the SZ-Mt composite calcined at 500 °C with the molar ratio of S/Zr of 0.3 showed the highest total reducing sugars yield of 30.1%. The characterization results revealed that the surface S O bonds of sulfated zirconium oxide could gradually change from O=S-OH groups (type I, -HSO 4 ) to O=S=O groups (type II, -S 2 O 7 ). It was concluded that the surface S-OH groups in type I were responsible for the hydrolysis of cellulose in the low molar ratio of S/Zr and the new S-OH bonds formed by breaking the S-O-S bonds in type II were contributed to the conversion of cellulose in the high molar ratio of S/Zr. Finally, the mechanism of cellulose hydrolysis on the SZ composites was suggested.
研究领域:
化学工程
·
材料科学
·
生物化学
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2018
·Vol. 8
·期 23
·12870-12878
·
IF 2.936
Li Tan,Hailong Li,Mengru Liu
In this study, CMC–LDH beads were prepared and characterized using SEM, FTIR and TG analysis. The beads were applied for the removal of Cr(VI) from aqueous solution. The effects of adsorbent dosage, initial pH and initial concentration of Cr(VI) solution on Cr(VI) uptake were investigated in detail. Moreover, adsorption isotherms and adsorption kinetic models were employed to analyze the adsorption process, and a preliminary study of the reusability of the adsorbent was performed. The experimental results showed that the CMC–LDH beads could remove Cr(VI) from aqueous solution efficiently. When the initial concentration of the Cr(VI) solution was 100 mg L−1 and the adsorbent dosage was 12 g L−1, the removal efficiency of Cr(VI) reached 96.2%. After the CMC–LDH beads were reused 10 times, the removal efficiency of Cr(VI) still remained at 89.6%.
研究领域:
环境科学
·
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）