JOURNAL OF THE AMERICAN CERAMIC SOCIETY
·
2024
·
IF 3.5
Mamuhe Yeerlan,Meng Zhang,Pengpeng Dai
Fe 3+ ions as near-infrared (NIR) activators are emerging as an alternative to Cr 3+ . 1–5 However, it is a challenge to develop Fe 3+ -activated NIR phosphors featuring tunable optical properties, high efficiency, and thermal stability. Herein, we present a series of near-unity internal quantum efficiency (IQE), wavelength-tunable and thermal stability NIR-emitting phosphors Sr 2− y Ca y Sc 1− x SbO 6 : x Fe 3+ (S 2− y C y S 1− x S: x Fe 3+ ). Sr 2 ScSbO 6 :1%Fe 3+ (SSS:1%Fe 3+ ) phosphor shows broadband NIR emission at 904 nm and near-unity IQE under excitation at 300 nm. Experimental and theoretical calculation results demonstrate that introduced Ca ions could increase the bandgap value and Debye temperature (Θ D ) of host from E g = 3.702 eV, Θ D = 609 K of y = 0 to E g = 3.801 eV, Θ D = 692 K of y = 2. Significantly, the resultant S 2− y C y S 1− x S:1%Fe 3+ NIR phosphors show wavelength-tunable emission from 904 to 952 nm and high IQE of 84.6%–97.5% as well as enhanced thermal stability ( I 423K / I 298K = 76.9%) of Ca 2 ScSbO 6 :1%Fe 3+ (CSS:1%Fe 3+ ) in comparison with that ( I 423K / I 298K = 70.6%) of pristine sample. We fabricated an NIR light-emitting diodes (LED) device by using CSS:1%Fe 3+ NIR phosphors with ultraviolet LED chip and demonstrated its potential applications in anticounterfeiting, information encryption, and night vision.
研究领域:
材料科学
·
光学
·
光子学
·
固体物理
✓ 已验证
DOI
高影响因子
Acta Biomaterialia
·
2020
·
IF 7.242
Yangyang Li,Mingxue Chen,Wenhao Zhou,Shuang Gao,Xujiang Luo,Liqing Peng,Jianglong Yan,Pei Wang,Qiyao Li,Yufeng Zheng,Shuyun Liu,Yan Cheng,Quanyi Guo
Considering the intrinsic poor self-healing capacity of meniscus, tissue engineering has become a new direction for the treatment of meniscus lesions. However, disturbed by mechanical stability and biocompatibility, most meniscus implants fail to relieve symptoms and prevent the development of osteoarthritis. The goal of this study was to develop a potential meniscal substitute for clinical application. Here, silk fibroin with good mechanical performance and biocompatibility, and strontium ion acting as bioactive factor, were incorporated with Ɛ-Polycaprolactone to fabricate a meniscus scaffold (SP-Sr). By the wet-electrospun method, the 3D SP-Sr provided suitable pore size (100–200 μm) and enough mechanical support (61.6 ± 2.9 MPa for tensile modulus and 0.11 ± 0.03 MPa for compressive modulus). Moreover, after addition of Sr 2+ , the SP-Sr seeded by rabbit adipose tissue-derived stromal cells (rADSCs) showed the highest secretion with 2.61- and 2.98-fold increase in collagen and aggrecan , respectively, compared with SF/PCL group. And the extracellular matrix related genes expression in SP-Sr also showed upregulation results. Particularly, the expression of the collagen II gene, which played a crucial role in the formation of meniscal inner avascular region, showed a 9-fold increase in SP-Sr compared with pure PCL group. Furthermore, the MRI results of SP-Sr implanted in rabbits with total meniscectomy for 6 months demonstrated effective prevention of meniscus extrusion and relieving joint space narrowing compared with meniscectomy group. And the effects of cartilage protection and delaying osteoarthritis development were confirmed by Pathological examination. Especially, after 6-month implantation, the neo-menisci showed similar structural constituent and mechanical performance. Statement of significance Meniscus regeneration faces great challenge due to the meniscus having limited healing potential owing to its anisotropic structure, its hypocellularity and hypovascularity. The present tissue engineering solutions have failed to maintain the biological function for meniscus reconstruction in vivo because of fragile and poor biocompatible materials, leading to long-term joint degeneration. The goal of this study was to develop a meniscal substitute potential for clinical application. Here, silk fibroin and strontium were incorporated with Ɛ-Polycaprolactone by wet-electrospinning method to fabricate a meniscus scaffold (SP-Sr). The 6-month implantation results revealed that SP-Sr scaffold was effective in preventing meniscus extrusion, cartilage protection and delaying osteoarthritis development, and the regenerated menisci showed similar structural constituent and mechanical performance.
研究领域:
组织工程
·
骨科
·
再生医学
·
生物材料
✓ 已验证
DOI
PubMed
高影响因子
Biomaterials Advances
·
2024
·
IF 5.5
Kunpeng Jia,Changpeng Zuo,Yan Xu,Wenfu Ma,Lingtao Wang,Yan Ji,Jie Chen,Qiuyang Zhang,Changjiang Pan,Tingting Liu
Titanium and its alloys are widely used as orthopedic implants owing to their good mechanical properties and excellent corrosion resistance. However, the insufficient osteogenic activity and antibacterial properties hinder their clinical applications. To address these issues, TiO 2 nanotube arrays (TNT) were first fabricated on the TA2 alloy surface via an anodizing technique, and strontium ions (Sr 2+ ) were then loaded by hydrothermal reaction (TNT + Sr) and annealing treatment (TNT + A). Subsequently, the polydopamine layer (TNT + PDA) was constructed to immobilize the carboxymethyl chitosan and alendronate sodium (TNT + CA) mixture. The prepared coatings were thoroughly characterized by scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray photoelectron spectrometer (XPS), attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffractometer (XRD), and water contact angle measurement. The results confirmed that Sr 2+ ions, polydopamine, and carboxymethyl chitosan/alendronate sodium were successfully immobilized on the nanotubes. The coating of TNT + CA significantly enhanced the hydrophilicity, and effectively delayed the release of Sr 2+ and alendronate. The TNT + CA coating significantly promoted osteoblast adhesion and proliferation, and up-regulated the expressions of alkaline phosphatase (ALP), osteocalcin (OCN), and osteoblast-specific transcription factor (RUNX2). TNT + CA was able to rapidly induce in situ hydroxyapatite deposition from the simulated body fluid (SBF). Moreover, TNT + CA coating showed inhibition against Escherichia coli and Staphylococcus aureus (especially against Escherichia coli ). The prepared TNT + CA coating provides a novel strategy for enhancing bone affinity, improving osteoblast behaviors, and antibacterial properties of titanium-based biomaterials.
研究领域:
生物材料
·
骨科
·
表面工程
·
纳米技术
·
生物医学工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2020
·
IF 3.99
Baojun Ding,Ziwei Wang,Xintong Wang,Wenbo Yang,Sifang Wang,Chong Li,Hongjing Dai,Shengyang Tao
In this paper, hydroxyapatite (HAP) nanoparticles (NPs) were synthesized by continuous flow using a 3D printed microreactor. The HAP NPs mostly consisted of acicular shape NPs and were mixed with chitosan (CS) to obtain precursor solution for the preparation of HAP/CS microspheres by electrospray method. The hybrid microspheres were used as economical adsorbents to remove Sr 2+ from aqueous solution. The effects of different adsorption parameters on the adsorption of Sr 2+ by HAP/CS were studied, including pH value, contact time, the dosage of HAP/CS, and coexisting ions. Adsorption of Sr 2+ using HAP/CS can accomplish in 4 h, and the saturated adsorption capacity was 234.20 mg g −1 . Langmuir isotherm model can describe the Sr 2+ adsorption process well, and the adsorption kinetics data were analyzed using the pseudo-second-order model, Weber–Morris intraparticle diffusion model and McKay equation. The adsorption amount showed no significant changes at 4 ≤ pH ≤ 10. The results suggest that HAP/CS could probably be used as an efficient and economical material to remove Sr 2+ from radioactive wastewater.
研究领域:
材料科学
·
环境科学
·
化学工程
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2022
·Vol. 51
·期 11
·4414-4422
·
IF 4.569
Zhi Wang,Xu Li,Mingyang Li,Jinxing Zhao,Zhenyang Liu,Dawei Wang,Li Guan,Fenghe Wang
With the increasing demand for new inorganic functional materials, more and more attention is paid to rare earth ion doped luminescent materials. In this work, an Eu2+ doped Ba4La6O(SiO4)6 phosphor was synthesized by the high temperature solid-phase method. In the phosphor, two Ba2+ sites could be occupied by Eu2+ cations to provide two different kinds of coordination environments, resulting in broad emitting bands in the range of 450–630 nm and ultra-wide excitation bands in the range of 250–500 nm. The presence of two different Eu2+ emitting centers is verified by measuring the photoluminescence spectra and decay curves in Ba4La6O(SiO4)6 phosphors. The temperature dependence of emission intensity and full width at half maximum of Eu2+ in the range of 293–453 K were investigated systematically. The substitution of Ba2+ by Sr2+ can adjust the crystal field; thus, the luminous intensity was improved by 2.07 times and T50 was increased from 380 K to 453 K. Due to the Sr2+ ion doping, some of the Eu3+ ions cannot be reduced and remain in the trivalent state. In addition, by integrating the as-prepared Ba1.42Sr2.5La6O(SiO4)6:Eu phosphor, commercial blue and red phosphors, and a 385 nm LED chip, a white-LED lamp was made, which realized an applicable color rendering index (Ra = 94.6). For the Ba0.42Sr3.5La6O(SiO4)6 phosphor, the emission can be shifted from yellow to green and to yellow by excitation wavelength variation from 250 to 360 and 480 nm, which proves that the phosphor is a promising candidate for anti-counterfeiting applications.
研究领域:
材料科学
·
光学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SOLID STATE IONICS
·
2020
·
IF 3.107
Xuefeng Shen,Qian Zhang,Tianxiang Ning,Jianlei Liu,Taoyong Liu,Zhiwei Luo,Yao He,Chunchun Qin,Anxian Lu
Garnet solid electrolyte is the most promising candidate among inorganic solid electrolytes due to its wide potential window, good compatibility and high safety. In this work, a dual doping strategy is offered for the development of garnet-type electrolytes with high ionic conductivity . Te 6+ is introduced into the Zr sites to stabilize the high-ionic conductivity cubic phase. Simultaneously, Sr 2+ enter the La sites to achieve a fine-tuning of the Li + concentration by charge compensation, acting as a sintering agent of Te 6+ /Sr 2+ doped electrolytes. The structure, chemical composition and ionic conductivity of Li 7 − 2 y + x La 3 − x Sr x Zr 2 − y Te y O 12 ( x = 0–0.25, and y = 0.35) electrolytes are systematically investigated by X-ray diffraction, Raman spectroscopy , scanning electron microscope , Energy Dispersive X-ray Spectroscopy, Inductively Coupled Plasma-Optical Emission Spectrometry and Alternating Current impedance. The results show that the optimal amount of Sr 2+ substitution helps to reduce the total resistance by promoting the growth of grains and ceramic densification . Among the investigated compositions, the composition with Li 6.425 La 2.875 Sr 0.125 Zr 1.65 Te 0.35 O 12 exhibits excellent performance with relative density of 97.95%, conductivity of 4.27 × 10 −4 S cm −1 at 25 °C and activation energy of 0.30 eV. The assembled Li/Li 6.425 La 2.875 Sr 0.125 Zr 1.65 Te 0.35 O 12 /Li symmetrical batteries are cycled galvanostatically under different current densities. The results show that the symmetrical battery can achieve good cyclic stability, good Li + stripping and plating process and low overpotential.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2025
·
IF 5.6
Xiaoshuai Zhang,Wen Xiong,Chengrun Liu,Zixuan Wang,Xiaoyan Yu,Xiaojie Li,Guodong Zhang,Panlai Li,Zhijun Wang
Exploring oxide-based deep red light-emitting phosphors is crucial for indoor plant lighting applications. In particular, designing Eu 2+ deep red emission in inorganic solids is challenging. In this paper, a cation substitution strategy was used to replace the Ca 2+ ions in the matrix with a certain concentration of Sr 2+ ions. A series of spectrally red-shifted Ca 1-x Sr x Sc 2 O 4 :Eu 2+ deep red phosphors were obtained under 460 nm light excitation. The substitution of Sr 2+ ions changes the local crystal field environment of Eu 2+ . The spectral shift from 656 nm to 702 nm was achieved by changing the centroid shift, the degree of polyhedral distortion and the lattice disorder. Combined with the need for practical applications, Ca 0.5 Sr 0.5 Sc 2 O 4 :0.01Eu 2+ phosphor and blue chip have been made into phosphor-converted light-emitting diodes for plant lighting, and the results of plant lighting experiments show that Ca 0.5 Sr 0.5 Sc 2 O 4 :0.01Eu 2+ phosphor has a certain application potential in plant lighting. In addition, this study will guide the exploration of new oxide-based deep red phosphors with Eu 2+ activation and for the realization of tunable emission through cation substitution.
研究领域:
材料科学
·
光学工程
·
植物学
✓ 已验证
产品关联
DOI
高影响因子
ACTA MATERIALIA
·
2018
·
IF 6.036
Jun-Cheng Zhang,Xin-Hua Fan,Xu Yan,Feng Xia,Weijin Kong,Yun-Ze Long,Xusheng Wang
Trap-controlled mechanoluminescence (ML) enables the direct observation of stress concentration of load-bearing objects through imaging the ML distribution, showing numerous prospects in stress detection, bio-imaging and optical displays. However, the applications of trap-controlled ML materials universally require long-time delay to fade the noise of symbiotic persistent luminescence (PersL) in order to achieve high-contrast ML images. In view of the difficulty to solve the PersL problem through individually eliminating the PersL traps, herein we propose a novel strategy of sacrificing trap density which decreases PersL and ML traps as a whole. By employing Sr 2+ substitution to decrease the trap density of Ca 2 Nb 2 O 7 :Pr 3+ , we identify a novel composition of (Ca 0.5 Sr 0.5 ) 2 Nb 2 O 7 :Pr 3+ displaying short-delay and high-contrast ML images, and evaluate its practicability through a 2-dimensional in-situ imaging experiment of dynamic stress distribution. The underlying mechanism is ascribed to the greater decrease ratio of PersL intensity than ML intensity as a result of the larger detrapping rate of traps due to stress (leading to ML) than that due to thermal energy (PersL). Furthermore, multi-spectral investigations of (Ca,Sr) 2 Nb 2 O 7 :Pr 3+ system reveal a distinctive electron transition process co-regulated by trap levels, charge transfer state and crystal field . The proposed strategy and the associated phosphors are expected to initiate the reconstruction of PersL-type ML materials and bring important implications for real-world stress imaging.
研究领域:
材料科学
·
光学工程
✓ 已验证
DOI
高影响因子
JOURNAL OF RADIOANALYTICAL AND NUCLEAR CHEMISTRY
·
2025
·
IF 1.6
Liu Jiahong,Shi Shuying,Liu Yan,Yang Heng,Yin Jing,Jiang Long,Yang Ailin,You Yongshuang,Deng Hao,Xiong Ying
Amorphous sodium zirconium phosphate (NaZrP) with the formula Zr(HPO 4 ) 0.66 (NaPO 4 ) 1.34 ·H 2 O exhibits superior Sr 2+ adsorption capacity (221.85 mg/g) driven by a chemisorption-dominated ion-exchange mechanism. Structural characterization confirms that the amorphous matrix of NaZrP provides accessible active sites (= ZrO 2 POONa/ = ZrO 2 POOH), while kinetic and thermodynamic analyses reveal rapid adsorption kinetics (99% Sr 2+ removal within 5 min) and an endothermic, spontaneous process (ΔG = − 36.56 kJ/mol). In simulated lake water containing competing ions (Na + /K + /Ca 2+ /Mg 2+ ), NaZrP retains 69.10% Sr 2+ uptake efficiency, demonstrating the practical potential for 90 Sr immobilization across diverse aquatic systems.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Polymer Materials
·
2022
·
IF 4.855
Fangwei Qi,Zhihui Wang,Yang Shuai,Shuping Peng,Cijun Shuai
Strontium ion (Sr2+) enabled us to endow polymer bone scaffolds with bioactivity owing to its excellent osteoinductive capacity. Nevertheless, the burst release of Sr2+ hindered its further application. Herein, strontium substituted hydroxyapatite (SrHA) was constructed to achieve a sustained release system. Specifically, Sr2+ could substitute Ca2+ in a HA lattice framework through ion exchange due to their similar ion radius. The ionic bond formed by Sr2+ and surrounding ions could prevent the rapid escape of Sr2+ and thereby achieve the sustained release of Sr2+. Subsequently, SrHA was introduced into the poly-l-lactic (PLLA) scaffold fabricated by selective laser sintering. Results demonstrated that PLLA/SrHA scaffolds presented a sustained Sr2+ release with a cumulative concentration of 5.6 mg/L over 28 days. The released Sr2+ significantly promoted the cell proliferation and differentiation. Furthermore, the tensile and compressive strengths of PLLA/SrHA scaffolds were also greatly enhanced in comparison with that of PLLA scaffolds. These positive findings demonstrated that PLLA/SrHA scaffolds had considerable potential for bone repair.
研究领域:
生物材料学
·
骨组织工程
·
医学
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2023
·
IF 5.2
Halizati Abulimiti,Reziwanguli Yantake,Aierpati Taximaimaiti,Taximaiti Yusufu,Aierken Sidike
Currently, there is a cyan gap in white light-emitting diodes (LEDs) manufactured by combining near-ultraviolet (NUV) chips with tricolour (blue/green/red) phosphors, resulting in a poor colour rendering index (Ra). Broadband blue-cyan phosphors contain blue, cyan and green luminescent components that complement the cyan gap. In this paper, feldspar-structured Ba 0.92- x Sr x Al 2 Si 2 O 8 :0.08Eu 2+ ( x = 0–0.5) phosphors were prepared by a high-temperature solid-phase method and a cation substitution strategy. A phase transition was achieved by varying the concentration of x , which resulted in the formation of two luminescent centres and a 10.33-fold enhancement of the luminescence intensity for Ba 0.92 Al 2 Si 2 O 8 :0.08Eu 2+ . The colour of the emission changed from the original green to blue-cyan, and the strongest emission peak with a half-height width of 94.5 nm was observed at a Sr 2+ concentration of 0.3 (30%) and covered the blue, cyan and green wavelength ranges (390–600 nm). The experimental value of the optical band of the substrate is 5.71 eV, and the luminous intensity of the Ba 0.62 Sr 0.3 Al 2 Si 2 O 8 :0.08Eu 2+ sample at 150 °C was 91.3% of that at room temperature. Ba 0.62 Sr 0.3 Al 2 Si 2 O 8 :0.08Eu 2+ , (Ca, Sr) AlSiN 3 :Eu 2+ and 365 nm NUV chips were successfully packaged into white LED devices. The colour rendering index (Ra) of the prepared white LED devices was 87, R9 was 89, the colour coordinates were (0.3763, 0.3382), and the colour temperature was 3759 K, which effectively solves the problem of the lack of cyan luminescent components in white LED devices and simplifies the manufacturing process of white LEDs.
研究领域:
材料科学
·
光学工程
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2021
·
IF 5.816
Chao Sun,Liuzhen Bian,Wang Yu,Yunting Hou,Lijun Wang,Lei Xing,Chaoyi Wang,Jun Peng,Jihua Peng,Shengli An
La-doped Sr 2-x La x Fe 1.5 Mo 0.5 O 6-δ perovskite oxides are synthesized and used as a symmetric electrode to evaluate the effect of La on the crystal structure, conductivity, and catalytic activity for O 2 reduction and H 2 oxidation reaction. The electronic doping effect dominates the oversize effect in Sr 2-x La x Fe 1.5 Mo 0.5 O 6-δ oxide, resulting in unit cell volume expansion and decreased conductivity in air. In addition, the introduction of La increases the chemical structural stability of Sr 2 Fe 1.5 Mo 0.5 O 6-δ in reducing condition due to the higher La–O bond compared with Sr–O bond, leading to high catalytic activity for the H 2 oxidation reaction. At 800 °C, the R p values of Sr 1.9 La 0.1 Fe 1.5 Mo 0.5 O 6-δ symmetric cell in air and wet H 2 are as low as 0.075 and 0.21 Ω cm 2 , respectively. Moreover, the peak power densities of 769, 561, 439, and 653 mW cm −2 at 850 °C are obtained when wet H 2 , CO, CH 4, and C 3 H 8 are used as fuels on Sr 1.9 La 0.1 Fe 1.5 Mo 0.5 O 6-δ /LSGM/Sr 1.9 La 0.1 Fe 1.5 Mo 0.5 O 6-δ cell. The symmetric cell also shows excellent stability (>100 h) in wet H 2 /air, implying Sr 1.9 La 0.1 Fe 1.5 Mo 0.5 O 6-δ oxide is a promising symmetric electrode material .
研究领域:
材料科学
·
能源科学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）