ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2023
·Vol. 30
·期 50
·108538-108552
·
IF 5.8
Wang Yongqiang,Bai Yibo,Han Che,Li Zaimei,Lun Xiaowen,Zhang Conglu
Graphite-like carbon nitride (g-C 3 N 4 ) is favored for its excellent physicochemical properties. However, the high complexation rate of photogenerated carriers greatly limits its practical applications. Based on this, a novel CQDs-doped carbon nitride nanosheets composite (CNS/CQDs) was prepared and applied to the visible light–induced activation of peroxymonosulfate (PMS) for meloxicam (Mel) and tetracycline (TC) degradation. The photocatalytic degradation of Mel and TC were remarkably promoted in the CNS/CQDs+PMS+vis system. Mel photodegradation of 99.90% was achieved over 30 min with 20 mg CNS/CQDs and 20 mg PMS at pH11. And TC photodegradation of 95.97% was achieved over 45 min with 20 mg CNS/CQDs and 20 mg PMS at nature pH6.5. The TOC mineralization rates of Mel and TC were 75.49% and 52.00%, respectively. The transient photocurrent response and electrochemical impedance measurements (EIS) results indicated that the doping of CQDs could improve the charge transfer efficiency of pure g-C 3 N 4 , and CNS/CQDs had a low charge transfer resistance. Capture experiments and EPR tests explored the effective actives in the CNS/CQDs+PMS+vis system. Possible degradation pathways of Mel were also analyzed. This study provides valid residual drugs degradation under the dual conditions of visible light catalytic oxidation and persulfate oxidation, which will be a novel perspective for advanced oxidation technology to effectively remove organic pollutants from water.
研究领域:
环境科学
·
光催化化学
·
水处理技术
·
纳米材料
·
高级氧化工艺
·
药物代谢
·
环境污染物降解
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2016
·Vol. 43
·期 3
·2969-2973
·
IF 2.758
Bing Xie,Haibo Zhang,Hao Kan,Sisi Liu,Ming-Yu Li,Zeyu Li,Shuai Zhu,Shiyong Qiu,Shenglin Jiang
This work demonstrates a highly efficient method for large-scale synthesis of elongated BaTiO 3 nanowires via a novel stirring hydrothermal process. Compared with conventional hydrothermal reaction , one-dimensional (1D) lead-free BaTiO 3 nanowires can be realized at an even lower temperature with a shorter dwelling time. Results suggest that the mechanical force-driven stirring process improved the diffusion and surface reaction rate of BaTiO 3 nanocrystal growth in the solution phase, apparently, leading to the growth of the BaTiO 3 nanowires via an oriented attachment mechanism. Meanwhile, to the best of our knowledge, this method is also the first reported protocol which is capable to grow elongated BaTiO 3 nanowires with length up to tens of micrometers. This research outcome provides a promising option for low cost, high-throughput fabrication of 1D nanostructure in respect of mass-manufacturing.
研究领域:
材料科学
·
纳米科技
·
无机合成
·
功能材料
·
铁电材料
✓ 已验证
DOI
高影响因子
DRUG DELIVERY
·
2019
·
IF 3.829
Yanfei Tao,Fei Yang,Kuiyu Meng,Dongmei Chen,Yujuan Yang,Kaixiang Zhou,Wanhe Luo,Wei Qu,Yuanhu Pan,Zonghui Yuan,Shuyu Xie
In our previous study, enrofloxacin-loaded docosanoic acid solid lipid nanoparticles (SLNs) could be effectively delivered to cells in vitro. In this study, its properties and exploitation as possible oral and intramuscular sustained release formulations for pigs were studied after being made into suspension. The re-dispersed time and sedimentation rate of the nanosuspension were 55 s and 1, respectively. It showed good stability when stored away from light and sustained release in pH = 7.4 PBS buffer. The suspension exhibited no irritation at the injection site and good palatability. Compared with commercial injection and soluble powder, the nanosuspension increased the bioavailability of enrofloxacin by 1.63 and 2.38 folds, and extended the mean residence time (MRT) of the drug from 11.27 and 12.33 to 37.76 and 35.15 h after intragastric and intramuscular administration, respectively. These results suggest that docosanoic acid SLN suspension (DAS) might be a promising oral and intramuscular sustained release formulation to enhance the pharmacological activity of enrofloxacin.
研究领域:
兽医学
·
药物递送系统
·
药剂学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS
·
2018
·
IF 2.207
Hongyu Shi,Na Li,Zhixia Sun,Tianqi Wang,Lin Xu
TiO 2 nanoparticles are commonly used as versatile precursors to make functional nanocomposite materials. However, the surface defects at grain boundaries of TiO 2 nanoparticles significantly affect the photoelectric properties of TiO 2 nanomaterials . In this work, we firstly prepared nanocomposites of TiO 2 and polyoxometalates (POMs) in which different POMs, including titanium-substituted POMs K 5 [PW 11 TiO 40 ] and K 7 [PW 10 Ti 2 O 40 ], are incorporated with TiO 2 nanoparticles so as to make an interface modification on grain boundaries of TiO 2 nanoparticles. Then the photoconductivities of the TiO 2 /POM nanocomposites were investigated through measurement of photocurrent responses, current-voltage curves, Mott-Schottky plots and surface photocurrent spectra. Compared with pure TiO 2 nanoparticles, TiO 2 /POM nanocomposites exhibit superior photoelectric properties, benefitting from the interface modification from different POMs. The gas sensing performance for acetone was also explored by use of the as-prepared photoconductive devices, and TiO 2 /PW 11 Ti exhibited a high gas sensing performance.
研究领域:
材料科学
·
纳米科技
·
半导体物理
·
传感器技术
·
光电子学
✓ 已验证
DOI
高影响因子
JOURNAL OF NON-CRYSTALLINE SOLIDS
·
2014
·
IF 1.716
J. Yuan,W.C. Wang,D.D. Chen,M.Y. Peng,Q.Y. Zhang,Z.H. Jiang
Enhanced 1.8 μm emission from Tm 3+ by Yb 3+ sensitization and bubbling in tungsten tellurite glasses has been demonstrated under the excitation of a 976 nm laser diode . Radiative properties such as spontaneous emission probabilities, radiative lifetimes and fluorescence branching ratios along with absorption and emission cross sections have been calculated from the absorption spectra . The influences of Yb 3+ concentration, Tm 3+ concentration, and bubbling time on spectroscopic properties have been thoroughly investigated. It is found that with increasing the bubbling time to 35 min, OH − content deceases sharply while 1.8 μm emission intensity improves greatly and 3 F 4 level lifetime prolongs to 1.57 ms close to radiative time. After 35 min, they change very little due to almost reaching the dynamic balance. The strength of interaction between Tm 3+ and OH − is determined. The energy transfer mechanism between Yb 3+ and Tm 3+ is proposed by photoemission spectroscopy and lifetime measurement. The energy transfer coefficients have been analyzed by the extended spectral overlap method and hopping model. Large ratio of the forward energy transfer from Yb 3+ to Tm 3+ to the backward one (223) and high energy transfer efficiency (97%) from Yb 3+ to Tm 3+ ensure efficient 1.8 μm emission. Hence, Yb 3+ sensitization and the reduction of OH − content could be expected to open up a possibility to achieve high efficient 2.0 μm lasing from Tm 3+ under a 976 nm LD pump.
研究领域:
光学材料
·
激光物理
·
固体激光器
·
光谱学
·
无机非金属材料
·
光子学
·
稀土发光材料
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2021
·Vol. 47
·期 23
·32641-32647
·
IF 4.527
Wei Liao,Yongqiang Tan,Chaowen Zhu,Zhen Teng,Peng Jia,Haibin Zhang
Multi-components and equimolar rare earth monosilicates, (Y 1/3 Dy 1/3 Er 1/3 ) 2 SiO 5 , (Y 1/3 Dy 1/3 Lu 1/3 ) 2 SiO 5 , (Y 1/4 Dy 1/4 Ho 1/4 Er 1/4 ) 2 SiO 5 and (Yb 1/4 Dy 1/4 Ho 1/4 Er 1/4 ) 2 SiO 5 , were prepared by solid-state reactions and the following hot-pressing. Dense microstructures with uniform elemental distributions were obtained for all samples. These investigated multi-components monosilicates exhibit low thermal conductivities and similar coefficients of thermal expansion with SiC. Moreover, they exhibit high corrosion resistances in 1400 °C water vapor , especially, four-components (Y 1/4 Dy 1/4 Ho 1/4 Er 1/4 ) 2 SiO 5 and (Yb 1/4 Dy 1/4 Ho 1/4 Er 1/4 ) 2 SiO 5 experienced almost invariable weights after small weight losses during the initial 0.5 h. All those results indicate that multi-components rare earth monosilicates are promising candidates of environmental barrier coatings for SiC/SiC composites.
研究领域:
材料科学
·
无机非金属材料
·
高温防护涂层
·
陶瓷基复合材料
·
表面工程
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2018
·
IF 5.116
Xiaozhen Chen,Ji Qi,Pan Wang,Chuang Li,Xiao Chen,Changhai Liang
Herein, PVA-Mo 2 C/Mo 2 N nanospheres with surface roughness are synthesized via a polyvinyl alcohol (PVA) involved approach and used for hydrogen evolution reaction (HER). The average crystallite size of the PVA protected nMo 2 CN nanospheres (6.1 nm) is one third of that of the PVA-Mo 2 C/Mo 2 N without PVA protection (17.9 nm). At 10 mA cm −2 current density, the as-synthesized PVA-Mo 2 C/Mo 2 N nanospheres with surface roughness exhibit HER overpotentials of 132 mV and 142 mV with corresponding Tafel slope of 51.8 mV dec −1 and 50.4 mV dec −1 in acid and alkaline medium, respectively. This high apparent activity can be attributed to the high intrinsic activity originated from the adjacent surface active sites of Mo 2 C and Mo 2 N as well as the large ECSA of PVA-Mo 2 C/Mo 2 N nanospheres with surface roughness.
研究领域:
材料科学
·
电化学
·
纳米催化
·
能源化学
·
表面科学
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2023
·Vol. 52
·期 21
·7143-7151
·
IF 4
Lu Liang,Xiaohui Li,Xiaoge Wang,Zhaoji Luo,Kun Lin,Qiang Li,Sihao Deng,Lunhua He,Xiaojun Kuang,Xianran Xing
Mixed electronic and oxide ionic conduction was enabled in digermanate-type La2−xCaxGe2O7−x/2 containing Ge3O10 chains and isolated GeO4 units by substitution of La3+ with Ca2+. The structure and solid solution limit of Ca doped La2Ge2O7 were studied by systematic experiments, including rotation electron diffraction (RED), X-ray diffraction (XRD) and neutron powder diffraction (NPD) experiments, etc. The preferred occupation of Ca2+ and oxygen vacancies was investigated by Rietveld analysis of the NPD data. The obtained conducting material La1.925Ca0.075Ge2O6.963 exhibits superior thermal stability and an order of magnitude improvement in conductivity compared to the parent La2Ge2O7 (∼9 × 10−5 S cm−1 at 1000 °C). BVEL calculations reveal that the oxygen vacancies were stabilized and transported within the framework of La2Ge2O7 by sharing oxygen and oxygen exchange between the adjacent Ge3O10 chains and GeO4 units, exhibiting a three-dimensional oxide ion transport nature.
研究领域:
无机化学
·
固态离子学
·
功能材料
·
结构化学
·
能源材料
·
晶体化学
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2016
·
IF 6.333
Xiaowei Kong,Xiaoliang Zhou,Yu Tian,Xiaoyan Wu,Jun Zhang,Wei Zuo
Development of cost-effective and efficient electrochemical catalysts for the fuel cells electrode is of prime importance to emerging renewable energy technologies . Here, we report for the first time the novel La 0.9 Ca 0.1 Fe 0.9 Nb 0.1 O 3−δ (LCFNb) perovskite with good potentiality for the electrode material of the symmetrical solid oxide fuel cells (SSOFC). The Sc 0.2 Zr 0.8 O 2−δ (SSZ) electrolyte supported symmetrical cells with impregnated LCFNb and LCFNb/SDC (Ce 0.8 Sm 0.2 O 2−δ ) electrodes achieve relatively high power outputs with maximum power densities (MPDs) reaching up to 392 and 528.6 mW cm −2 at 850 °C in dry H 2 , respectively, indicating the excellent electro-catalytic activity of LCFNb towards both hydrogen oxidation and oxygen reduction. Besides, the MPDs of the symmetrical cells with LCFNb/SDC composite electrodes in CO and syngas (CO: H 2 = 1:1) are almost identical to those in H 2 , implying that LCFNb material has similar catalytic activities to carbon monoxide compared with hydrogen. High durability in both H 2 , CO and syngas during the short term stability tests for 50 h are also obtained, showing desirable structure stability, and carbon deposition resistance of LCFNb based electrodes. The present results indicate that the LCFNb perovskite with remarkable cell performance is a promising electrode material for symmetrical SOFCs.
研究领域:
材料科学
·
电化学
·
能源材料
·
燃料电池
·
催化化学
✓ 已验证
DOI
高影响因子
Advanced Energy Materials
·
2017
·Vol. 7
·期 15
·1700087
·
IF 16.721
Ting Jin,Yongchang Liu,Yang Li,Kangzhe Cao,Xiaojun Wang,Lifang Jiao
NaVPO 4 F has received a great deal of attention as cathode material for Na-ion batteries due to its high theoretical capacity (143 mA h g −1 ), high voltage platform, and structural stability. Novel NaVPO 4 F/C nanofibers are successfully prepared via a feasible electrospinning method and subsequent heat treatment as self-standing cathode for Na-ion batteries. Based on the morphological and microstructural characterization, it can be seen that the NaVPO 4 F/C nanofibers are smooth and continuous with NaVPO 4 F nanoparticles (≈6 nm) embedded in porous carbon matrix. For Na-storage, this electrode exhibits extraordinary electrochemical performance: a high capacity (126.3 mA h g −1 at 1 C), a superior rate capability (61.2 mA h g −1 at 50 C), and ultralong cyclability (96.5% capacity retention after 1000 cycles at 2 C). 1D NaVPO 4 F/C nanofibers that interlink into 3D conductive network improve the conductivity of NaVPO 4 F, and effectively restrain the aggregation of NaVPO 4 F particles during charge/discharge process, leading to the high performance.
研究领域:
材料科学
·
电化学
·
纳米技术
·
能源存储
·
无机非金属材料
·
固态化学
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Hongyuan Qin,Jiawei Huang,Xueli Zhang,Ling Yu,Yang Yu
In this study, lanthanum hydroxide adsorbent was synthesized through a simple hydrothermal method and applied for removing phosphate from water. The optimal adsorbent was obtained at the La/OH molar ratio of 4:1. The adsorbent showed rapid adsorption of phosphate within the first 4 h in which approximately 84% of the equilibrium adsorption capacity can be achieved. The phosphate uptake was highly dependent on solution pH. The better fit of the Langmuir isotherm model to experimental data indicated that the monolayer adsorption occurred and the maximum adsorption capacity of 193.9 mg/g was accomplished at pH 7.0. The presence of fluoride could significantly retard the uptake of phosphate. X-ray photoelectron spectroscopy analysis indicated that hydroxyl groups on the adsorbent surface played the most key role in the adsorption. The phosphate ions were adsorbed on the adsorbent through the formation of inner-sphere complexes.
研究领域:
环境化学
·
纳米材料科学
·
水污染控制
·
表面化学
·
吸附科学
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2022
·
IF 7.336
Yifan Zhang,Laifu Yang,Wenqiang Wang,Gengchao Wang
LiNbO 3 is an intercalation material with high theoretical specific capacity, which is promising for lithium-ion capacitor (LIC) anode. However, the poor charge transfer dynamics makes LiNbO 3 unable to match the capacitive cathode in rate performance and cycle stability, resulting in poor electrochemical performance of the device. Herein, through the integrated process of in-situ nitrogen-doping with polypyrrole as the nitrogen source and hydrothermal deposition, the coaxial heterostructure of ultrafine LiNbO 3 nanoparticles and nitrogen-doped carbon nanotubes (NCNT) was realized. The large lithium-ion accessible surface and the bonding with the conductive channel significantly enhance the pseudocapacitive behavior of LiNbO 3 (capacitance contribution of 78.5% at 1 mV s −1 ). After 1000 cycles at a current density of 2 A g −1 , NCNT@LiNbO 3 still has a specific capacity of 154.9 mAh g −1 (89.8%). Thus, the assembled NCNT@LiNbO 3 //AC devices can charge and discharge up to 10000 cycles at a current density of 2 A g −1 , and the capacity retention rate can still reach 90.3%, and can provide an energy density of 142 Wh kg −1 . This work provides ideas for the interface and structure design of nanocomposite electrode materials.
研究领域:
材料科学
·
电化学
·
纳米复合材料
·
能源存储
·
界面工程
·
电极设计
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）