SOLAR ENERGY MATERIALS AND SOLAR CELLS
·
2026
·
IF 6.6
Hyejeong Jin,Hyunseo Park,Shurouq Abdulqadir Mohammed,Mengmeng Chu,Maha Nur Aida,Changgeon Lim,Hasnain Yousuf,Muhammad Quddamah Khokhar,Junsin Yi
Silicon heterojunction (HJT) solar cells are sensitive to recombination losses and moisture-induced degradation at mechanically exposed edges. In this study, an untreated 0 wt% control and Nafion solutions with concentrations of 3, 5, 7, and 10 wt% were evaluated on mechanically cut 4 cm × 4 cm HJT solar cells, corresponding to an active area of 16 cm 2 , four exposed edges, and a total exposed edge length of 16 cm. The devices were evaluated using illuminated J–V measurements, dark I–V characterization, damp heat testing at 85°C/85% RH, photoluminescence, X-ray photoelectron spectroscopy, and a calibrated analytical edge-recombination consistency assessment. The host-cell group before cutting exhibited average values of J sc = 39.20 ± 0.05 mA/cm 2 , V oc = 749.36 ± 1.00 mV, FF = 81.70 ± 0.30%, and PCE = 24.00 ± 0.15%. After mechanical cutting, the untreated cut-cell group exhibited J sc = 38.20 ± 0.03 mA/cm 2 , V oc = 722.00 ± 1.00 mV, FF = 78.39 ± 0.45%, and PCE = 21.62 ± 0.13%. The optimized 3 wt% Nafion-treated group achieved J sc = 39.18 ± 0.05 mA/cm 2 , V oc = 748.12 ± 1.32 mV, FF = 81.55 ± 0.32%, and PCE = 23.91 ± 0.15%. Based on the group-average values, the treatment recovered approximately 95.47% of the cutting-induced V oc loss and 96.22% of the PCE loss. The treated cells also retained higher illuminated J–V parameters during damp heat exposure, demonstrating that concentration-optimized Nafion edge passivation can improve both the efficiency and environmental stability of mechanically cut HJT solar cells.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Fei Liu,Lijin Cheng,Hao Li,Shaojun Liu
The dielectric properties of titanate-based microwave ceramics are usually degraded by oxygen vacancies induced by prolonged sintering at high temperature. In this study, the activation sintering and improvement of dielectric properties for 0.7CaTi 1-x O 3 -0.3NdAlO 3 ceramics could be achieved by slight adjusting the stoichiometric ratio of Ti 4+ ions at B-site (CTNA, x = 0.0000, 0.0025, 0.0050, 0.0075). As x increasing from 0.0000 to 0.0050, the relative densities, maximum densification rate, and maximum densification rate temperature all increase. This is attributed to the generation of oxygen vacancy defects that can facilitate atomic diffusion. When x further increase to 0.0075, even though the number of oxygen vacancies continues to increase, the substitution of Nd 3+ with larger ionic radius (1.27 Å) at B-site, compared to Ti 4+ (0.605 Å), induce significant lattice distortion. Consequently, the relative densities of CTNA ceramics (x = 0.0075) remains comparable to that of CTNA ceramics (x = 0.0050). The substitution of Ti 4+ by smaller Al 3+ (0.535 Å) at B-site in CTNA ceramics (x = 0.0050) result in a reduced lattice constant and unti cell volume, which is conducive to the reduction of intrinsic loss and the improvement of dielectric properties: ε r = 45.92; Q × f = 43,900 GHz, and τ f = 2.88 ppm/°C.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2026
·
IF 9.2
Runyu Zhang,Yudong Sui,Lina Han,Yehua Jiang
In this work, graphene oxide (GO) was integrated into the established synthesis route of Ni-TMA MOF. The results demonstrate that the resulting Ni-TMA MOF/GO shows pronounced catalytic activity toward the hydrogen sorption behavior of MgH 2 . Morphological characterization indicates that the as-prepared Ni-TMA MOF/GO possesses a dandelion-like microspherical architecture, featuring an overall spherical profile and a hierarchically porous interior with abundant voids. This structural configuration provides enlarged specific surface area and a high density of accessible active sites. Among all investigated composites, MgH 2 -3 wt.% Ni-TMA MOF/GO delivers the best overall hydrogen-storage performance. At 573 K under 2.6 MPa H 2 , it reaches a maximum hydrogen uptake of 6.3 wt%. The composite also exhibits rapid absorption kinetics, taking up 6.0 wt% H 2 within 1 min. In addition, it maintains good cycling durability: after 100 hydrogenation/dehydrogenation cycles, the reversible capacity remains 5.8 wt%.
✓ 已验证
产品关联
DOI
高影响因子
TALANTA
·
2026
·
IF 6.7
Linying Cheng,Xiang Liu,Zixin Zhang,Jing Liu,Jianru Tang,Xiaohua Zhu,Youyu Zhang,Meiling Liu
Copper ions (Cu 2+ ) are essential micronutrients but become hazardous when accumulated in excess, necessitating reliable, sensitive, and field-deployable detection methods. Herein, we report a fluorescent Mn-based MOF nanozyme (Mn-TCPP) that exhibits intrinsic oxidase-like activity, capable of catalyzing the oxidation of non-fluorescent o -phenylenediamine (OPD) to fluorescent 2,3-diaminophenazine (DAP) with an emission peak at 560 nm, while the Mn-TCPP itself displays characteristic fluorescence at 655 nm. Upon exposure to Cu 2+ , the stronger affinity of Cu 2+ toward the porphyrinic TCPP ligand displaces Mn 2+ from the framework, forming Cu-TCPP. This metal-exchange process simultaneously quenches the 655 nm fluorescence of the MOF and attenuates its oxidase-mimicking activity, whereas free Cu 2+ in solution independently catalyzes OPD oxidation, further enhancing the 560 nm emission. Leveraging this dual-response mechanism, we develop a ratiometric fluorescence sensing strategy for Cu 2+ detection based on the intensity ratio F 560 /F 655 . The calibration curve follows a linear equation: F 560 /F 655 = 0.201x-0.001 (0.2-10 μM, R 2 = 0.985) and y = 0.002x+2.061 (10-100 μM, R 2 = 0.994) with the limit of detection (LOD) of 81 nM (S/N = 3). The sensor exhibits excellent selectivity over competing metal ions, and the method reliability is validated by standard addition recovery experiments in real water and rice samples. Furthermore, the Mn-TCPP nanozyme is embedded into an agarose hydrogel matrix, enabling visual, instrument-free monitoring of Cu 2+ contamination: increasing Cu 2+ concentrations induce a discernible fluorescence color transition from orange to yellow under 365 nm illumination. This work presents a tunable MOF platform that exploits competitive targets synchronous modulation of fluorescence and enzyme-mimicking activity, providing a robust, selective, and field-deployable ratiometric sensor for Cu 2+ .
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2026
·
IF 8.8
Cuijing Liu,Bo He,Lei Li,Mengtian Bai,Zhangji Fan,Jiangfeng Song,Linbo Li,Xihong He,Hideto Matsuyama
Covalent organic frameworks (COFs) are promising candidates for fabricating ion-selective membranes towards Li + extraction from brines. However, most COF membranes feature nanoscale pores, limiting their capability to sieve angstrom-sized ions. Herein, a DG-TBB membrane with angstrom-sized, lithiophilic and positive channels was fabricated via the condensation of a small, positively charged amine (1,3-diaminoguanidine monohydrochloride, DG) with an aldehyde containing lithiophilic groups (2,4,6-trimethoxy-1,3,5-benzenetricarbaldehyde, TBB). For comparison, the DG-TFB membrane based on 1,3,5-triformylbenzene (TFB) without lithiophilic groups was adopted to clarify the role of Li + -affinitive sites, while the ODH-TBB membrane containing neutral oxalyl dihydrazide (ODH) was employed to evaluate charge effect. Benefiting from the synergistic effects of Li + affinity and Donnan exclusion, DG-TBB membrane delivered the highest Li + permeation rate of 73.6 mmol m −2 h −1 and Li + /Mg 2+ selectivity of 1200, which were superior to DG-TFB (4.3 mmol m −2 h −1 , selectivity of 238) and ODH-TBB (64.9 mmol m −2 h −1 , selectivity of 39). Moreover, DG-TBB exhibited robust separation performance in diverse practical scenarios and for various mono-/divalent cations. This study demonstrates that the rational integration of angstrom-sized pores, lithiophilicity and positive charge into COF channels enables highly efficient ion separation.
✓ 已验证
产品关联
DOI
高影响因子
Asian Journal of Pharmaceutical Sciences
·
2026
·
IF 12.6
Xianbin Sun,Xinyi Wang,Fangying Zheng,Ruofei Xu,Xinyi Shen,Ding Tan,Xudong Li,Ya Wang,Kaiming Peng,Haijun Chen,Xiumei Li,Yu Gao
The rising threat of antibiotic resistance severely compromises the treatment of bacterial pneumonia, underscoring the urgent need for innovative and comprehensive therapeutic strategies. Here, we developed an innovative theranostic nanoplatform (Dex/BTGd) through the coordinated assembly of tetracycline, gadolinium ion (Gd 3+ ) and baicalin (Ba), which acts synergistically to combat infection, enable non-invasive magnetic resonance imaging (MRI), and regulate the lung microenvironment. Dex/BTGd demonstrated potent antibacterial activity against clinically relevant pathogens, effectively disrupting biofilms and overcoming tetracycline resistance. The incorporated Gd 3+ allowed targeted visualization of pulmonary infection sites by MRI, facilitating timely disease assessment. Beyond its direct antibacterial effects, the nanoplatform modulated the inflammatory microenvironment by scavenging reactive oxygen species, promoting macrophage polarization from the pro-inflammatory to the anti-inflammatory phenotype, and suppressing profibrotic transforming growth factor-β signaling. In a murine model of tetracycline-resistant Pseudomonas aeruginosa pneumonia, Dex/BTGd significantly reduced bacterial load, alleviated pulmonary edema and fibrosis, and enabled targeted MRI visualization of infected lesions. This integrated strategy of pathogen clearance, microenvironment modulation, and tissue repair offers a multifaceted solution to drug-resistant bacterial pneumonia, providing a promising blueprint for next-generation anti-infective systems.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FOOD RESEARCH INTERNATIONAL
·
2026
·
IF 8.8
Chunling Nie,Zejie Chen,Yijun Liu,Zhonghui Shen,Yujia Dang,Yingtian Qu,Pengrui Wu,Hong Zeng,Yanbo Wang,Jianguo Wang
Salt ions induced CNCs aggregation by electric double layer compression. • Aggregated CNCs formed interfacial bridging structures between emulsion droplets. • Salt-induced CNCs networks enhanced interfacial reinforcement and emulsion viscosity. • AMP/HPMC Pickering emulsions exhibited remarkable long-term stability at 60 days. • Salt-induced CNCs aggregation hindered the contact between AMP and digestive enzymes. Salt ions play a key role in governing the property of food system. In this work, the effects of salt ions on physicochemical property of cellulose nanocrystals (CNCs) and their stabilization behavior in Amylopectin/Hydroxypropyl methylcellulose (AMP/HPMC) water-in-water (W/W) emulsions were investigated. The addition of NaCl significantly reduced the absolute value of zeta potential of CNCs and resulted in particle aggregation, forming of network structures. These structure changes promoted the droplet clustering and bridging flocculation of AMP/HPMC W/W Pickering emulsions and enhanced their stability during long-term storage (60 days). Rheological analysis revealed that increasing NaCl concentration resulted in enhanced viscosity and obvious viscous-dominated behavior due to the synergistic interaction between salt-induced CNCs network and thermal-induced aggregation of HPMC. Furthermore, in vitro digestion results showed that salt-induced structural changes of CNCs effectively limited enzyme accessibility, thereby reducing AMP digestion and glucose release. This work demonstrates that salt ions could regulate the structure-function relationship of CNCs-stabilized W/W Pickering emulsions, and provides new insights to design novel food systems with controlled digestion properties. Download: Download high-res image (188KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
APPLIED ENERGY
·
2026
·
IF 12.2
Wenjia Li,Xiangkai Kong,Yueyang Wang,Shibo Cui,Fei Ma,Zhenyu Tian
Photoelectrochemical water splitting is a promising technology for producing hydrogen from solar energy. However, during the scale-up process, substrate resistance and current-collection loss result in a significant decrease in the photoelectrochemical current density. In this study, a high light flux concentration anion exchange membrane photoelectrochemical water splitting reactor was developed using a hydrothermally derived α-Fe 2 O 3 photoanode and a sprayed FeNiCo cathode supported on porous titanium fiber felt. The porous Ti fiber network facilitates charge transport, electrolyte infiltration, and bubble release, suitable for concentrated light operation. By concentrating a large-area of sunlight onto a small-area electrode, the requirements for substrate resistance and current-collection loss are reduced. Meanwhile, the high light flux concentration brings about an increase in both incident photons and temperature, and that the two have a synergistic effect on the photoelectrochemical water splitting reaction. The photoelectrochemical current density is elevated. Compared with operating condition at 5 suns, 30 °C, the reactor temperature could reach 70 °C under 20 suns, and the current density was significantly increased from 1.59 mA cm −2 to 6.47 mA cm −2 at 1.23 V. After optimization, the bias-assisted solar to hydrogen efficiencies at 5, 15, and 20 suns exceeded that under the initial condition and reached 0.386%, 0.390%, and 0.379%, respectively. These results demonstrate that photo-thermal synergy enhances the current density by reducing charge carrier recombination, while bubble management improves reactor-level photoelectrochemical performance by mitigating both optical losses and mass-transfer limitations.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2026
·
IF 8.8
Congcong Zhou,Erqiao Chen,Jinfeng Yuan,Zhongting Liu,Yang Jiao,Hongjun Lin,Yanchao Xu,Liguo Shen
To address the loose structure and limited separation performance of polyester nanofiltration membranes arising from the low reactivity of hydroxyl monomers, this study proposes a phosphate buffer solution (PBS)-based pH-regulated interfacial polymerization strategy to construct high-performance polyester nanofiltration membranes using tannic acid (TA) and trimesoyl chloride (TMC). Using tannic acid as the aqueous-phase monomer and trimesoyl chloride as the organic-phase monomer, high-performance tannic acid-based polyester nanofiltration membranes were successfully fabricated. By regulating the acid-base environment during interfacial polymerization with PBS, the oxidation state of the phenolic hydroxyl groups in TA was effectively controlled, which in turn significantly enhanced the structural compactness of the polyester selective layer. Experimental results showed that the membrane prepared under the optimal condition of pH 8 exhibited a water permeability of 10.2 L m −2 h −1 ·bar −1 and a Na 2 SO 4 rejection of 98.2%, while the rejection of six antibiotics, including tetracycline and ciprofloxacin, remained higher than 96.5%. Meanwhile, the membrane displayed lower surface roughness and stronger surface hydrophilicity, and maintained stable flux and rejection performance during 7 days of continuous operation. These results demonstrate that the PBS buffer system can effectively promote the formation of a highly crosslinked polyester selective layer by stabilizing the interfacial reaction environment and regulating the chemical state of TA, thereby achieving a synergistic enhancement in the permeability and selectivity of polyester nanofiltration membranes.
✓ 已验证
产品关联
DOI
高影响因子
LWT-FOOD SCIENCE AND TECHNOLOGY
·
2026
·
IF 7.1
Tsekwi Gracious Rinwi,Wenhong Gao,Qi-Jun Wang,Ke Shen,Xiaotong Wang,Ning Wang,Zhong Han,Ji Ma
Combination of PEF and isochoric preservation improved shelf-life stability. • Immersion in citric and ascorbic acid solutions caused hypotonic swelling. • Phenolic compounds were better retained with PEF and isochoric preservation. • Combined PEF and isochoric preservation synergistically reduced enzymatic browning and microbial growth. Minimally processed litchi is prone to quality loss due to its high moisture content, biochemical activity, and vulnerability to microbial growth. This study examined the combined effects of PEF pre-treatment and isochoric freezing (−3 °C, 235 kPa) on the quality and shelf-life of minimally processed litchi, with additional tests using ascorbic and citric acid solutions to assess their impact on preservation. Results showed that samples treated by vacuum packaging followed by isochoric freezing (VP + IF) and PEF pre-treatment combined with vacuum packaging and isochoric freezing (PEF + VP + IF) effectively maintained tissue integrity and enhanced water retention, thereby stabilising key quality parameters, including color, pH, ascorbic acid, and total phenolics, and slight titratable acidity decreased. Notably, the PEF + VP + IF treatment exhibited more pronounced positive effects, likely due to enhanced tissue permeability and improved mass transfer. Conversely, samples treated by IVP + IF and PEF + IVP + IF exhibited hypotonic swelling, resulting in significant reductions in texture, total soluble solids, ascorbic acid content, water-holding capacity, and enzyme activity, along with a slight increase in total phenolics. Nevertheless, microbial counts decreased across all treatments, with PEF + IVP + IF achieving the lowest microbial load.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ETHNOPHARMACOLOGY
·
2026
·
IF 6.8
Xinyang Du,Jingran Li,Shuai Qu,Hong Kan,Yingping Wang
Ethnopharmacological relevance Epimedium koreanum Nakai is a well-recognized tonic herb in traditional Chinese medicine that has been extensively used for thousands of years in the management of bone metabolic diseases. According to classic traditional Chinese medicine processing principles, stir-frying Epimedii Folium with mutton fat can synergistically augment its “kidney-warming and bone-strengthening” therapeutic effects. However, the modern pharmacological basis and precise molecular mechanisms underlying this processing-enhanced efficacy remain largely unexplored. Aim of the study This study aimed to compare the anti-osteoporotic effects of raw and mutton fat-processed Epimedii Folium in postmenopausal osteoporosis, and to reveal the underlying mechanisms. Materials and methods Multiple techniques were applied, including ultra performance liquid chromatography coupled with Q Exactive mass spectrometry, network pharmacology, cell and animal models, non-targeted metabolomics, Western blot analysis, and quantitative real-time reverse transcription polymerase chain reaction. These approaches enabled component analysis, mechanism prediction, and multi-level in vitro and in vivo validation. Results Processed Epimedii Folium contained more blood-absorbed constituents, and more effectively improved bone mass, trabecular structure, osteoclast activity and osteogenesis. It regulated glycerophospholipid metabolism, inhibited inflammatory signaling, and relieved stress on the osteoprotegerin/receptor activator of nuclear factor-κB ligand axis to restore bone homeostasis. Conclusion Mutton fat-processed Epimedii Folium exerts anti-osteoporotic effects through a “metabolic remodeling–inflammation inhibition–bone homeostasis restoration” axis. This study provides modern scientific evidence for the processing method of Epimedium recorded in the Chinese Pharmacopoeia, and offers a valuable paradigm for research on traditional Chinese medicine processing.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FOOD RESEARCH INTERNATIONAL
·
2026
·
IF 8.8
Hui Zhang,Chunmei Liu,Jiahao Yang,Shanglin Li,Meng Yang,Jingbo Liu,Ting Zhang,Yajuan Li
Dual-ligand nanoparticles enable oral co-delivery of quercetin and anthocyanins. • Core–shell structure provides high encapsulation efficiency and stability. • Nanoparticles enhance intestinal absorption via energy-dependent endocytosis. • Oral NPs surpass atorvastatin in reducing obesity, hepatic steatosis and inflammation. • NPs reshape gut microbiota, enriching beneficial and suppressing harmful bacteria. Obesity is a global epidemic driven in part by poor oral bioavailability of bioactive food compounds. Here, we develop dual-ligand-functionalized nanoparticles (NPs) for the oral co-delivery of hydrophilic anthocyanins (ACN) and hydrophobic quercetin (Que) to combat obesity. The system is assembled from lactobionic acid-modified chitosan (LACS) and glycyrrhetinic acid-modified casein (GACA), forming a core–shell structure that protects both compounds against gastrointestinal degradation and affords pH-responsive colloidal stability. In Caco-2/HT29-MTX-E12 co-culture models, the LACS-ACN-GACA-Que NPs enhance intestinal absorption via energy-dependent endocytosis, facilitate transcellular transport, and achieve sustained intracellular accumulation. Orally administered to high-fat diet-induced obese mice, the NPs surpass both the unencapsulated bioactive mixture and the clinical drug atorvastatin in reducing body weight gain, white adipose tissue hypertrophy, hepatic steatosis, and systemic inflammation. These anti-obesity benefits are accompanied by favorable gut microbiota remodeling: enrichment of short-chain fatty acid-producing taxa ( Oscillospiraceae , Ruminococcaceae , Lachnospiraceae ) and suppression of pro-inflammatory lineages ( Erysipelotrichaceae ). Collectively, this dual-ligand strategy establishes a versatile oral delivery platform that protects and synergistically delivers disparate bioactive compounds, offering a promising approach for obesity management. Download: Download high-res image (361KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子